Manufacturing Commons^™

Experimental Manufacturing Optimization Of 3d-Printed Ducted Fans, Stanlie Cerda-Cruz

Discovery Day - Daytona Beach

This study aims to assess the efficiency gains, feasibility, and practicality of 3D printing fan and ducts with pre and post processing techniques. With the rapid expansion of MAV use; labs, students, hobbyists, can benefit from manufacturing Electric Ducted Fans (EDFs), both fans and ducts, in-house rather than purchasing traditional propellers. There are several advantages of utilizing EDFs, as they can minimize wing tip vortices, reduce wake contraction, and induce a duct lip Coanda effect which all lead to an increased system efficiency. However, EDF implementation in MAV's remain largely unexplored due to the difficulty of development and the production …

Smart Process Planning For Automated Fiber Placement, Matthew J. Godbold

All Dissertations

Automated Fiber Placement (AFP) is a preeminent manufacturing technology for producing high-performance composite structures, offering precise material placement, reduced waste, and the potential for highly optimized lightweight designs. While AFP has been widely adopted in aerospace applications, its broader use across industries such as automotive, wind energy, maritime, and sporting goods remains limited. A key barrier to wider adoption is the traditional separation of design, manufacturing, and inspection processes, which drives up cost and results in inefficiencies, sub-optimal designs, and limited feedback between lifecycle stages. In current practice, manufacturing is treated as an isolated process, disconnected from early-stage design decisions …

3d Semi-Analytical Thermo-Elasto-Plastic Model For Additive Manufacturing, Tao Liu, Ming C. Leu, Edward C. Kinzel, Chinedum Okwudire

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In additive manufacturing (AM), stress field drives distortion and warping and promotes delamination and cracking. Fast, accurate stress prediction is therefore essential for AM process planning and control, including real-time adaptive control, AM digital twins, data-driven and physics-driven workflows. However, spot-wise thermo-elasto-plastic finite element method (FEM) are often too slow for design iteration or real time use. Existing semi-analytical thermo-elasto-plastic approaches achieve high speed but are largely limited to 2D. In this paper, a full 3D semi-analytical thermo-elasto-plastic model for AM is built. The method uses a spot-wise analytical thermal field as the load and computes displacements and stresses via …

Optimization Of Aluminum Coating Deposition Parameters To Enhance The Performance Of Automotive Headlamps, Gulirano Saidakhmedova, Giovanni Maizza

Technical science and innovation

The paper investigates the influence of the optical characteristics of functional coatings applied to automotive reflectors on vehicle active safety parameters, with a focus on the range and intensity of road illumination. The study examines the mathematical relationship between the maximum luminous intensity of a headlamp, the object detection distance, and the reflection coefficient  of an aluminium layer deposited via vacuum thermal evaporation. The main factors driving the degradation of surface reflectivity (including oxidation, thermal degradation of the base coat, and surface roughness) are analysed. It is demonstrated that a decrease in the reflection coefficient during operation directly impairs the …

Direct Ink Writing Of Functional Fiber/Granular Composites, Zhuoyuan Yang

Doctoral Dissertations and Master's Theses

Direct ink writing provides a versatile manufacturing route for fabricating functional fiber and granular composites with controlled architecture, tunable interfaces, and customized material distributions. Fiber reinforced composites offer high stiffness, strength, fatigue resistance, and functional anisotropy, while granular composites provide scalable access to particle based structures with high material efficiency and broad resource compatibility. However, the additive manufacturing of these composite systems remains challenging. For fiber based composites, precise control of fiber placement, matrix impregnation, interfacial bonding, and freestanding deposition is difficult to achieve during printing. For granular composites, stable particle flow, controllable packing, binder infiltration, and shape retention are …

Mars Rover Wheels And Drive, Presley S. Sacavitch, Ryan W. Trevena, Dylan A. Mack, Daniel Hudak

Mechanical Engineering

Cal Poly’s Poly1Rover team, advised by Professor Rich Murray, aims to deploy four student-designed mini-Mars rovers, each equipped with a sample-tube retrieval claw, before 2030. However, the wheels of Poly1Rover’s current 6th generation rover are not ready for deployment to Mars, as they do not utilize space-grade materials, are not optimized for manufacturability, and lack sufficient spoke compliance to absorb landing and high-impact loads. This project will be developed by a team of Mechanical Engineering students at California Polytechnic State University, San Luis Obispo (Cal Poly): Daniel Hudak, Dylan Mack, Presley Sacavitch, and Ryan Trevena. Next Intent is providing funding …

Improving The Reliability And Performance Of A Supersonic Indraft Tube Wind Tunnel, Christian J. Kaml

Master's Theses

Access to supersonic testing is increasing in demand, and wind tunnels remain one of the safest and most cost-effective methods for gathering high-speed flow data. Despite being more economical than alternative options, supersonic wind tunnel facilities often require substantial investment to construct, operate, and maintain.

The novel indraft tube tunnel architecture was conceived as a high-speed flow testbed that incorporates features of both Ludwieg tubes and indraft wind tunnels to maintain costs low enough to be accessible even to small universities. This design was first developed and tested in 2018 at California Polytechnic State University, featuring a cost per test …

Lunar Manufacturing Systems And The Role Of Additive Recycling Technologies, Camille A. Newman

Honors Theses

Renewed international interest in sustained lunar exploration has created a growing demand for technologies to support long-duration space exploration. Part of the recent Artemis missions and the Moon to Mars initiative is to improve key mission capabilities and fill critical gaps necessary to sustain lunar habitation. Waste management, recycling systems, and manufacturing systems have been identified as critical technologies that need further development before a sustained mission is possible. This thesis explores the feasibility of an additive manufacturing and recycling system designed to process plastic waste generated during extended lunar habitation. Initial research focused on existing manufacturing and recycling technologies …

Manufacturing Of Functional Surface Coatings In The Automotive Industry, Gulirano Saidakhmedova

Technical science and innovation

The development of environmentally sustainable technologies for material processing represents one of the most pressing scientific and technical challenges in modern industrial production. This issue is particularly relevant to the automotive industry, where growing demands for energy efficiency, durability, and environmental safety necessitate the adoption of advanced manufacturing methods. Special attention is given to developing vacuum-based, import-substituting equipment and technologies for producing functional coatings from composite materials with predefined physical, mechanical, and optical properties, including reflective and protective characteristics. Current requirements for mechanical engineering products and production technologies drive the need for innovative approaches to material processing and specialized technical …

Detecting And Repairing Conflicting Constraints In Co-Trained Physics-Informed Neural Networks For Composite Curing Processes, Cooper J. Evans

Dissertations, Master's Theses and Master's Reports

Composite materials have become a critical component of modern manufacturing, especially in the automotive and aerospace industries. The curing process for these composites has been modeled using a variety of partial differential equations representing the heat transfer and composite curing kinetics. Optimizing the applied temperature profile is critical for maximizing the efficiency and capacity of composite part manufacturers. Constraints must be placed on the inputs and outputs of the model, including but not limited to, the applied temperature profile, part temperature, and final degree of cure. Conflicting sets of constraints are easy to unknowingly impose due to the highly coupled …

Corrigendum To “3d Semi-Analytical Thermo-Elasto-Plastic Model For Additive Manufacturing”(Additive Manufacturing, (2026), 127, C, (105308), (S2214860426002344), 10.1016/J.Addma.2026.105308), Tao Liu, Ming C. Leu, Edward C. Kinzel, Chinedum Okwudire

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The author regret about the correction in the Equation B(1) in original article. The corrected version of the Equation B(1) is given below,(1.1)∂uxxx,ξ∂x=116πμ1−ν4ν−1x−ξxR3−3x−ξx3R5−8ν−5x−ξxR13+34ν−3x−ξx3R15−18x−ξxzξzR15+30x−ξx3zξzR17−12ν−12ν−1x−ξxR1R1+z+ξz2+4ν−12ν−1x−ξx3R13R1+z+ξz2+8ν−12ν−1x−ξx3R12R1+z+ξz3 The authors would like to apologise for any inconvenience caused. DOI of original article: < 10.1016/j.addma.2026.105308>

Optimization Of Post-Processing Methods For Additively Manufactured Metals, Julia R. Carano

Williams Honors College, Honors Research Projects

Ultrasonic Nanocrystal Surface Modification (UNSM) is a process used to change the surface hardness of flat-faced materials. It is a machining process using a high-powered laser and a blunt-tipped tool at high speeds which aims to improve the uniformity of the surface on most metals. By heating and pressing the surface of the workpiece, the grains of the material become less rounded and more cohesive on a microscopic level. This, ideally, results in a workpiece with improved material properties. The changes were previously observed through hardness testing.

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Fused Filament Fabrication Additive Manufacturing Of 17-4 Ph Stainless Steel: Process–Structure–Property Relationships In Magnetic Materials, Maanav Patel

Theses and Dissertations

Additive manufacturing (AM) enables the fabrication of complex metallic components through layer-by-layer processing directly from digital models. Among AM techniques, material extrusion–based processes such as fused filament fabrication (FFF) provide an accessible method for producing metal parts using filament feedstocks composed of metal powders and polymer binders. When applied to precipitation-hardening stainless steels such as 17-4 PH, the processing route and heat treatments can influence the resulting microstructure and functional properties. This work investigates the magnetic behavior of 17-4 PH stainless steel fabricated using FFF and evaluates how heat treatment conditions influence measured magnetic properties. Samples were produced and analyzed …

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

In-Situ Defect Detection In Selective Laser Melting Using Convolutional Neural Networks, Ethan Gaigalas

Master's Theses

This thesis develops and trains a convolutional neural network (CNN) to classify defects in metal parts produced by selective laser melting (SLM) using acoustic emission (AE) data. The model successfully identified porosity and standard build layers with high accuracy but consistently struggled to classify lack of fusion (LOF) defects, regardless of input type, normalization, or class count. These results suggest that while AE signals contain distinguishable features for certain defect types, LOF signals may be too subtle or inconsistent for reliable detection. The study addresses the ongoing challenge of in-situ quality monitoring in metal additive manufacturing, where defects like cracks, …

3d Printed Fixed Wing Aircraft Competition, Sidney E. Long, Mitchell Heise, Jack Bride, Daniel Salinas

Mechanical Engineering

Cal State LA and Arlington University, Texas are hosting the same 3D printed, fixed wing aircraft competition for 2025. Cal Poly requires a competitive plane that can adhere to each rule and be piloted remotely to achieve the longest time in the air. The plane must utilize solely 3D printing technology for the wings, body, and all other structures. The only off-the-shelf components can be the motor and electronics, as well as mechanical devices such as hinges.

Thermal Characterization Of 3d Printing Materials For Increasing Insulation Potential And Practicality, Jackson H. Minnick

Mechanical Engineering Undergraduate Honors Theses

This study served as an exploration into the possible existence of a correlation between the infill lattice structure of a 3D printed wall section and the thermal performance of that sample as characterized by thermal conductivity measured in units of Watts per meter Kelvin. With the continual increase in the practicality, fidelity, and applicable fields of additive manufacturing, namely FDM 3D printing, research on specific print characteristics and their effects on the material and thermal characteristics of the part in question is steadily becoming more commonplace. Although the thermal conductivity of 3D printed wall sections as a function of infill …

Ultrafast Laser Surface Structuring For Wettability Control On Copper, Akshay Arvind Nagvenkar

All Theses

Wettability is a crucial surface property influencing various phenomena, including heat transfer, cell adhesion, and corrosion. Engineering devices can achieve superior performance by precisely manipulating surface wettability. As a result, extensive research has focused on developing surfaces that exhibit either extreme water attraction (superhydrophilic) or strong water repellency (superhydrophobic). Tailoring surface wettability paves the way for numerous applications, such as drag reduction in marine vessels, controlled drug delivery, efficient water collection, advanced liquid transport systems, oil-water separation, anti-corrosion coatings, friction reduction, and self-cleaning materials. Ultrafast laser surface structuring is a promising approach for engineering multifunctional surfaces, effectively modifying material properties …

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

Experimental And Theoretical Fracture Analysis Of Additively Manufactured Orthotropic V-Notches, Venkata Siva Sainath Bavapuram

Theses and Dissertations

This study presents a comprehensive investigation into the fracture behavior of additively manufactured orthotropic V-notched components made of Acrylonitrile Butadiene Styrene (ABS) material. The research integrates both theoretical and finite element approaches to evaluate stress intensity factors (SIFs) in Modes-I and II, which are fundamental in characterizing stress field distributions around notches under applied loading conditions. Unlike isotropic materials, where stress fields depend only on geometry of the component, the anisotropic nature of 3D-printed ABS introduces a dependency on material properties that necessitate different approaches to include anisotropy of the material.

Tensile specimens are 3D-printed with specific material orientations to …

40 - Design, Fabrication, And Installation Of Morphing Control Surfaces For Small-Scale Uas, Kyle Purser

Undergraduate Research Symposium

Morphing control surface technology, inspired by organic structures and compliant mechanisms, offers significant potential for enhancing the aerodynamic efficiency and performance of unmanned aerial systems (UAS). Despite these benefits, its adoption has been hindered by complexities in design, manufacturing, and installation, particularly when compared to traditional flap systems. This research explores the design, fabrication, and integration of morphing control surfaces for small-scale UAS using additive manufacturing techniques. To reduce costs and streamline the design process, fused deposition modeling (FDM) additive manufacturing was employed for component fabrication. An off-the-shelf Horizon Sport Cub S2 served as the testing platform, modified with a …

Fabrication Of Ultra High-Temperature Compact Heat Exchanger By Extrusion-Based Ceramic Additive Manufacturing, Abid Hasan Rafi, David W. Lipke, Jeremy Lee Watts, Greg Hilmas, Ming-Chuan Leu

Miners Solving for Tomorrow Research Conference

No abstract provided.

Additive Manufacturing Of Thermoplastic Composites, Matik Heskin, K. Chandrashekhara, Richard Billo, Ming-Chuan Leu, Thomas P. Schuman

Miners Solving for Tomorrow Research Conference

No abstract provided.

Image-Based Stage Prediction Of Pressure Injuries Using Deep Learning, Mehedi Tusar, Fateme Fayyazbakhsh, Ming-Chuan Leu

Miners Solving for Tomorrow Research Conference

No abstract provided.

Experiment-Based Superposition Thermal Modeling Of Laser Powder Bed Fusion, Cody S. Lough, Tao Liu, Robert G. Landers, Douglas A. Bristow, James A. Drallmeier, Ben Brown, Edward C. Kinzel

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Parts experience significant local thermal variations during the Laser Powder Bed Fusion (LPBF) metal Additive Manufacturing (AM) process, providing a potential source of defects. Near real-time thermal predictions can enable better process planning and facilitate corrections on subsequent layers to enable the engineering of laser parameter and scan path combinations that avoid defect inducing scenarios. This paper considers an experiment-based Discrete Green's Function (DGF) thermal model for temperature field prediction in LPBF. An analytical framework is developed and used to calculate an experimental DGF (i.e., powder bed's single pulse temperature response) from spatiotemporal Short-Wave Infrared (SWIR) camera data. The extracted …

Development Of A Design Tool For Tow-Steered Composite Structures With Machine Learning-Assisted Modeling, Bangde Liu

Industrial, Manufacturing, and Systems Engineering Dissertations - Archive

Fiber-reinforced composites (FRCs) are widely used in aerospace, automotive, and other engineering applications due to their lightweight characteristics and superior mechanical properties. Traditional FRCs employ a fixed fiber orientation in each layer, and while different layup sequences can tailor performance, the mechanical properties remain spatially uniform. Tow-steered composites, which enable fibers to follow curvilinear paths, offer the potential for spatially varying stiffness and strength, improving structural performance.

This dissertation addresses key challenges in modeling and designing tow-steered composite structures, including the lack of commercial design tools, the high computational cost of design optimization, and the need to efficiently evaluate manufacturing …

Development And Processing Of Shape Memory Polymer Composites (Smpcs) For Application In Structural Robotics And Robotic Sensors., Kavish Sudan

Electronic Theses and Dissertations

Shape Memory Polymers (SMPs) have attracted significant attention since their introduction in the 1980s due to their remarkable ability to regain their original shape from a temporarily deformed state when exposed to an external stimulus, typically heat. This shape memory effect, driven by thermal transitions such as the glass transition temperature (T_g) or melting temperature (T_m), has made SMPs highly attractive for applications in soft robotics, aerospace, and biomedical devices. However, SMPs face challenges such as limited mechanical strength, thermal stability, and electrical conductivity, which hinder their broader adoption in advanced applications. To address these challenges, …

Kissing Bond Assessment In Adhesive Bonded Carbon Fiber Reinforced Composites Using Dielectric Spectroscopy, Minhazur Rahman

Mechanical and Aerospace Engineering Dissertations - Archive

The widespread use of fiber-reinforced composites in industries such as space, aviation, automobiles, and construction necessitates the formation of robust composite joints between critical structural components. Although adhesive-bonded joints are superior with improved load distribution and reduced weight, they are often overlooked in favor of bolted joints and mechanical fasteners due to the lack of reliable Non-Destructive Evaluation (NDE) techniques for adhesive-bonded composites. The anisotropic nature of the substrate and the intricate interfacial interactions between the adherend and adhesive material present significant challenges for conventional NDE methods. Moreover, weak adhesive bonds can result from uncontrolled manufacturing parameters, such as accidental …

Materials Testing For Large Format 3d Printing, William Jenkins

Williams Honors College, Honors Research Projects

An ABS Carbon Fiber blend was printed into single walled hexagons at a variety of settings on a Cincinnati BAAM large format 3D printer. These hexagons were then cut down into sheets and had tensile and flexural test samples cut out of them, in order for materials testing to be performed. Tensile strength, tensile strain, young’s modulus, flexural strength, deflection and elastic modulus were all determined. A desktop CNC machine and a planer were purchased for the manufacturing of these samples, and an efficient cutting procedure was designed and optimized. After all data collection concluded, this data was thoroughly analyzed, …