Manufacturing Commons^™

Development And Testing Of A 1:70 Scale Model Wind Turbine Of The Iea Reference 15 Mw Floating Offshore System, Amber Parker

Electronic Theses and Dissertations

This thesis presents the development of a 1/70th scale performance-matched wind turbine intended for wind and wave basin model testing of commercially viable floating wind turbine structures based off of the International Energy Agency (IEA) Wind 15 MW design. The focus of this demonstration is to test active blade pitch response controls and to provide an experimental dataset for use by modelers and industry for future turbine improvements. Future research is planned to test the turbine in conjunction with an actively damping hull to test the interactions between the two control systems.

Outlined in this thesis are the methods of …

Rehology And Electrical Conductivity Of Particulate Composites In Additive Manufacturing, Bin Xia

Mechanical Engineering Research Theses and Dissertations

Extrusion-based multi-functional additive manufacturing (AM) has been a rapidly developing area in AM recently. Particulate composites are widely used in this area to provide different functionalities with different types of particulate additives. However, there is no systematic understanding of the behavior of particulate composites during extrusion (especially in small nozzles) or of their properties once deposited in the build. This work investigates the properties of the type of particulate composites usually used in additive manufacturing, composed of a polymer matrix material and particulate additives within the micrometer scale. The focus is on the material rheology in the nozzle/capillary (for the …

Rocket Motor Nozzle, Corey Hillegass

Williams Honors College, Honors Research Projects

For this honors research and senior design project, the authors will research, analyze, and manufacture a rocket motor nozzle for the Akronauts rocket design team. This research and design project will improve how the rocket design team will decide and manufacture nozzles going forward. The impact of this improvement allows the rocket design team to take steps toward being self-sustaining by manufacturing student designed parts as opposed to commercially bought parts. This will not only be successful in increasing student impact on future designs, but also provides a technical challenge for the authors and will present as an impressive feat …

Design Of Banner Tow Mechanism For Bush Plane, Kyle Ciarrone, Ivan Martin, Rishabh Gadi, Tyler Brandt

Williams Honors College, Honors Research Projects

The 2019-2020 AIAA DBF objective was to design, build, and test a banner-towing bush plane that carries wooden passengers and luggage. Senior members on the team undertook the creation of the banner tow mechanism subsystem as their senior design project on behalf of the design team due to the challenge of its mechanical design and the aerodynamic considerations regarding its placement and enclosure aboard the aircraft. The competition as well as access to campus resources were canceled due to COVID-19, so full testing and integration of the mechanism was not achieved. However, the engineering design process was experienced from the …

Space Dynamics Laboratory Payload Challenge: Autonomous Water Sampling Uav, Thomas Wheeler, Zachary Williams, Joseph Stack

Williams Honors College, Honors Research Projects

The following report has been completed over the course of the Fall 2018 and Spring 2019 semesters at The University of Akron by Joseph P. Stack (Aerospace Systems Engineering), Thomas J. Wheeler (Mechanical Engineering) and Zachary M. Williams (Mechanical Engineering). The purpose of this project was to create a payload system for the Akronauts Rocket Design Team to use at the Intercollegiate Rocket Engineering Competition (IREC) Spaceport America Cup. The Competition as a challenge that is sponsored by Space Dynamics Laboratory specifically regarding payload systems. The challenge in very open-ended and allows student to identify their own scientific experiment and …

Generator Design: A Study Of Optimized Airflow, Rachel Wattleworth

Williams Honors College, Honors Research Projects

The core goal of this project was to prototype, test, and evaluate a new type of fan for the Safran Electrical & Power air-cooled generators. The idea of a new fan being made for these two generators arose when they were not adhering to design requirements. A base mixed-flow fan was created to test on multiple generators. Upon creating a prototype, it will be tested to prove if it can increase the air flow, decrease temperatures, and increase power and life of the machines. They all proved to be successful and achieve the main objectives for this project. Data such …

Leading Edge Boundary Layer Suction Device For The Cal Poly Rolling Road Wind Tunnel, Daniel C. Glover, Liam M. Madden, Robert J. Cabri

Mechanical Engineering

Over the course of three quarters from Fall of 2016 to Spring of 2017, our team designed and built a boundary layer suction device. The boundary layer suction device has three main functions: a scoop that redirects most of the boundary layer air out of the wind tunnel, fans that suck the remaining boundary layer air through a porous plate and ducting and out of the wind tunnel, and a transition bridge that transitions the remaining air smoothly onto the rolling road. The wind tunnel is owned by Cal Poly and the rolling road is a new addition to it. …