Energy Systems Commons^™

Loss Modeling Of A Permanent Magnet Dc Motor Drive Water Pumping System, Nelson Lujara

Tanzania Journal of Engineering and Technology (TJET)

The paper presents an analytical approach to the determination of losses in each of the sub-systems of the Photovoltaic (PV) Permanent Magnet DC Motor (PMDC) drive water pumping system with and without maximum power tracking. The losses of the system at varying heads are firstly, determined using parameters from the data sheets and then validated by experimental results. The results are used to establish the head and the flow rate optimal operating point of the system.

Scheduling And Cooperative Control Of Electric Vehicles' Charging At Highway Service Stations, Florida Solar Energy Center, Azwirman Gusrialdi

FSEC Energy Research Center®

This is a re-print version of a publication for the 53rd IEEE Conference on Decision and Control, Los Angeles, California, USA, December 15-17, 2014. Due to their limited ranges, electric vehicles (EVs)need to be periodically charged during their long-distance travels on a highway. Compared to the fossil-fuel powered vehicles, the charging of a single EV takes much more time(up to 30 mins versus 2 mins). As the number of EVs on highways increases, adequate charging infrastructure needs to be put in place. Nonetheless waiting times for EVs to get charged at service stations could still vary significantly unless an appropriate …

Process Simulation Of Biomass Gasification Integrated With A Solid Oxide Fuel Cell Stack, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

Biomass gasification-solid oxide fuel cell (BG-SOFC) combined heat and power (CHP) systems are of major interest in the context of climate change mitigation, energy security and increasing energy efficiency. Aspen Plus is employed to simulate various BG-SOFC CHP systems. The aim of the research work is to investigate the technical feasibility of these systems and to study the influence of important operating parameters and examine integration options. Systems based on dual fluidised bed steam gasification and tubular SOFC technologies are modelled. The cathode recycle and electric heater integration options are not attractive in comparison to the base case anode recycle …

Phased Retrofits In Existing Homes In Florida Phase I: Shallow And Deep Retrofits, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The U.S. Department of Energy (DOE) Building America program, in collaboration with Florida Power & Light (FPL), is conducting a phased residential energy-efficiency retrofit program. This research seeks to establish impacts on annual energy and peak energy reductions from the technologies applied at two levels of retrofit ' shallow and deep, with savings levels approaching the Building America program goals of reducing whole-house energy use by 40%. Under the Phased Deep Retrofit (PDR) project, we have installed phased, energy-efficiency retrofits in a sample of 56 existing, all-electric homes. End-use savings and economic evaluation results from the phased measure packages and …

Heat Transfer Enhancement And Applications Of Femtosecond Laser Processed Metallic Surfaces, Corey M. Kruse

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, functionalized 304 stainless steel metallic surfaces were created with the use of a Femtosecond Laser Surface Processing (FLSP) technique. The laser processing technique produces self-organized micro/nanostructures on the surface. The heat transfer performance of various FLSP functionalized surfaces were characterized through pool boiling and Leidenfrost experiments. Enhancement in both the nucleate and film boiling heat transfer were observed through an increase of the critical heat flux and heat transfer coefficient as well as shifts in the Leidenfrost temperature respectively. For both experiments, a polished reference sample was used as a baseline line to compare against the …

Direct Synthesis Of Methane From Co2-H2O Co-Electrolysis In Tubular Solid Oxide Electrolysis Cells, Long Chen, Fanglin Chen, Changrong Xia

Faculty Publications

Directly converting CO₂ to hydrocarbons offers a potential route for carbon-neutral energy technologies. Here we report a novel design, integrating the high-temperature CO₂–H₂O co-electrolysis and low-temperature Fischer–Tropsch synthesis in a single tubular unit, for the direct synthesis of methane from CO₂ with a substantial yield of 11.84%.

Analysis And Optimization Of The Scheffler Solar Concentrator, Simone Alberti

Master's Theses

The Scheffler reflector is a new solar concentrator design which maintains a fixed focus while only having a single axis tracking mechanism. This design makes the construction and operation of high temperature solar concentrators accessible to developing nations. In this project, I wrote computer simulation codes to better understand the dynamics and the effect of deformation or deviations from ideal conditions in order to define necessary manufacturing and operational tolerances. These tools and knowledge drove the prototyping of new reflector concepts by myself and other students on my team. A fiberglass prototype was able to drive the cost of a …

Methane Production By A Packed-Bed Anaerobic Digester Fed Dairy Barn Flush Water, Sean Richard Thomson

Master's Theses

Packed-bed digesters are an alternative to covered lagoon digesters for methane production and anaerobic treatment of dilute wastewaters such as dairy barn flush water. The physical media of packed-beds retain biofilms, often allowing increased treatment rates. Previous studies have evaluated several types of media for digestion of dilute wastewaters, but cost and media fouling have setback commercial development. A major operational cost has been effluent recirculation pumping.

In the present effort, a novel approach to anaerobic digestion of flush dairy water was developed at pilot-scale: broken walnut shells were used as a low-cost packed-bed medium and effluent recirculation was replaced …

Thermal Assessment Of A Latent-Heat Energy Storage Module During Melting And Freezing For Solar Energy Applications, Antonio Miguel Ramos Archibold

USF Tampa Graduate Theses and Dissertations

Capital investment reduction, exergetic efficiency improvement and material compatibility issues have been identified as the primary techno-economic challenges associated, with the near-term development and deployment of thermal energy storage (TES) in commercial-scale concentrating solar power plants. Three TES techniques have gained attention in the solar energy research community as possible candidates to reduce the cost of solar-generated electricity, namely (1) sensible heat storage, (2) latent heat (tank filled with phase change materials (PCMs) or encapsulated PCMs packed in a vessel) and (3) thermochemical storage. Among these the PCM macro-encapsulation approach seems to be one of the most-promising methods because of …

Optimised Integration Of Grid-Connected Renewable Energy Technologies For Domestic Application In Ireland, Zhe Li

Doctoral

The utilisation of renewable energy resources for electricity and thermal generation is extremely important in Ireland due to the lack of indigenous fossil fuel resources and the high dependence on imported fossil fuels. The release of environmentally-damaging greenhouse gases in the combustion of fossil fuels in electricity and thermal generation is also a major issue. In Ireland, the domestic dwelling is recognised as one of the biggest energy consumers. The use of renewable energy technologies to provide electricity, heating and hotwater can effectively offset the usage of fossil fuels. The aim of this research study was to develop a novel …

Modeling Hydrodynamic Stability Of Incline-Liquid Airblast Nozzle For Gas Turbine Combustion, Kevin Matiko

Doctoral Dissertations and Master's Theses

Fuel is a major cost item for civil transport airplanes. Minimizing fuel consumption of these crafts is a stream of economic opportunity and a stage for innovation, competition and exploration. Regardless of the fuel type, bio or crude oil based, the civil transport stakeholders would like to minimize fuel consumption of their airplanes. The mixing of fuel and air is a critical process for optimum combustion in gas turbine engines due to its high influence on the downstream combustion process. The need for minimizing fuel consumption coupled with the requirement for combustion systems to perform well at all flight conditions …

Second Semi-Annual Program Progress Performance Report For University Transportation Systems, Florida Solar Energy Center, David L. Block

FSEC Energy Research Center®

The Electric Vehicle Transportation Center (EVTC) supports the U.S. Department of Transportation's strategic goal of planning for near-term integration of alternative fuel vehicles as a means to build a sustainable transportation system. The project will evaluate technologies, standards and policies to ensure seamless integration of electric vehicles (EVs) into a complex transportation network and electricity grid. The EVTC will bridge the gap between deployment of electric vehicles and the traditional transportation system.

The EVTC's goals were described in detail in the previous Program Progress Performance Report. These goals have not changed significantly and this report provides updates to each of …

Thermoelectric Waste Heat Recovery In Automobile Exhaust Systems: Topological Studies And Performance Analysis, Sumeet Kumar

Open Access Dissertations

The demand for improved fuel efficiency in automobiles has placed an emphasis on exhaust system waste heat recovery as a 40% of the fuel's chemical energy is lost to the environment in modern spark ignition engines. To advance fuel economy, researchers are currently evaluating technologies to exploit exhaust stream thermal power using thermoelectric generators (TEGs) that operate using the Seebeck effect. Thermoelectric generators have the potential to recover some of this waste energy in the exhaust stream potentially improving fuel economy by as much as 5%. ^ Attempts are made to maximize the electrical power generation by optimizing the thermoelectric …

Electric Vehicle Life Cycle Cost Assessment, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

The Electric Vehicle Transportation Center (EVTC) has developed a life cycle cost (LCC) model to include all reasonable costs associated with vehicle ownership over a 5, 10, 15, or 20-year period. The EVTC LCC model compares ownership costs of conventional vehicles to plug-in hybrid and battery electric vehicles. Internal combustion engines using gasoline, ethanol, or diesel are considered. The analysis includes costs for tires, insurance and maintenance, federal incentives, state tax, dealership fee, and financed interest payments. Traction battery replacement costs are difficult to ascertain yet are included to investigate their impact on overall life cycle costs. Economic factors used …

An Analysis Of Fuel Cell Vehicle Models By Major Automakers, Florida Solar Energy Center, Nan Qin

FSEC Energy Research Center®

Fuel cell electric vehicles (FCEVs) use hydrogen as fuel and exhaust only water. They provide driving ranges and fueling times comparable to gasoline vehicles. Despite the advantages, FCEVs have been in and out of spot light of the auto industry for the past several decades. The information on the development of fuel cell vehicles by major automakers is disparate. This report systematically examined the technical developments of FCEVs since the introduction of the first lab-based fuel cell vehicle in 1966. It included an overview of 117 FCEV models from 31 automakers. It should help the stakeholders to gain an insight …

Achieving Challenge Home In Affordable Housing In The Hot-Humid Climate, Florida Solar Energy Center, David Beal

FSEC Energy Research Center®

The Building America Partnership for Improved Residential Construction (BA-PIRC) worked with two affordable housing builders who pursued and achieved CH certification. Both builders needed very few changes to reach CH; however, both were already certifying homes under the ENERGY STAR® for Homes Standard v.3.1. Habitat for Humanity affiliates’ mortgage terms are 0% interest over a 30-year mortgage to qualified buyers. To improve relevance of the study to the general homebuilding community, the cost-effectiveness calculations herein are based on a code-minimum reference rather than the builders’ standard practice (ENERGY STAR), and projected first year cash flow is provided for both the …

Modeling Of Mixed Friction Interactions Occurring In Axial Piston Pumps, Andrew C. Adelsperger, Lizhi Shang, Dan Mizell, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

Axial piston pumps are integral to a variety of hydraulic systems due to their versatility and reliability, but most attempts to model them for design purposes have failed. However, software which fully models the fluid structures within these pumps, such as the FSTI gap design program, has improved significantly. Unfortunately, current discrepancies between simulated and measured friction forces on the cylinder due to the fluid drag and piston movement need to be eliminated so that more accurate simulation of these pumps in operation is possible. Friction measurements and FSTI simulation outputs were analyzed with MATLAB filters and graphs, resulting in …

The Role Of Surface Area In Catalytic Gasification Of Biomass, Elizabeth A. Wachs, Nitish Kumar, Indraneel Sircar, Prithviraja Basak, Jay P. Gore Phd

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gasification of biomass has the potential to provide a carbon-negative source of liquid fuels. The current limited use of gasification is due in part to the high temperatures necessary to achieve high conversion levels. These temperatures can be lowered by the use of catalysts, but the mechanisms by which catalysts affect the reaction rate are not fully understood. Here, the structural component of potassium carbonate’s role in the gasification process was examined. Samples of pinewood sawdust were impregnated with potassium carbonate, then pyrolyzed with N2 in a fixed bed reactor at 750°C (heater thermocouple reading). Half of the char was …

Cost Effectiveness Of 2015 Iecc Compliance Using The Hers Index, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

The EnergyGauge HERS software tool is used to examine the 2012 IECC Standard Reference Design (IECC SRD) configuration for three-bedroom, one-story 2000 ft² and three-bedroom, two-story 2,400 ft² single-family homes in sixteen representative U.S. cities. The energy use of the 2012 SRD homes is compared against the energy use of homes complying with the 2015 IECC using the ERI compliance method. HERS simulations for each home are conducted for both a best case home orientation and a worst case home orientation. Improvements to the 2012 IECC SRD homes are made such that the HERS Index for the homes …

Investigation Of Potential Benefits Of Revising Exception 1 Under Florida Building Code, Energy Conservation, Section 101.4.7.1.1 Duct Sealing Upon Equipment Replacement, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

Section 101.4.7.1.1, Duct sealing upon equipment replacement (Mandatory), of the 2012 Supplement to the Florida Building Code, Energy Conservation went into effect briefly in 2013. The new section required sealing of accessible ducts at the time of HVAC equipment replacement. Exception #1 however, eliminates the requirement for ducts in conditioned space, and by doing so, effectively eliminates the sealing requirement for building cavities in conditioned space that are used as air distribution paths. However, test results show that these building cavities are often connected to adjacent unconditioned spaces, in effect they are not really in the conditioned space because they …

Analysis Of Different Techniques For Improving Performance Of Flat Plate Solar Collectors For Fruits Drying, Godfrey Mbabaye

Tanzania Journal of Engineering and Technology (TJET)

Fruits drying had become a broader technology in fruits and vegetables value addition. The technology is reported to be a promising way of drying without incurring higher cost but its adaptation has not been feasible in rural areas. Solar dryers have been developed but its poor performance limits its applicability. In this study, several techniques for modifications of traditional solar collector were addressed. It was observed that, varying collector designs in different techniques, a range of collector performances can be archived. The research shows that, collector efficiency can be improved by 9.6% when employing double duct counter flow compared to …

Initial Testing Of A Unitary Hvac System Advanced Control Module, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

Testing of a unitary HVAC system advanced control module and the results.

Assessment Of Energy Efficient Methods Of Indoor Humidity Control For Florida Building Commission Research, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

This research project was conducted with the primary objective to identify approaches and technologies which can achieve energy-efficient latent cooling in light of code requirements that may increase overall ventilation rates in new Florida homes. This report covers the work of two primary efforts of completing a literature review and testing a few space conditioning methods in a mechanically ventilated building. Results from a literature review provide a list of various approaches to managing the latent load in homes with emphasis on energy efficiency and cost-effectiveness. In addition to a literature review, controlled experiments using four different approaches to space …

A Review Of Home Airtightness And Ventilation Approaches For Florida Building Commission Research, Florida Solar Energy Center, Jeffrey Sonne

FSEC Energy Research Center®

This research project was conducted with the primary objectives of 1) providing a literature review, examination of experimental data, and calculations of energy impacts of using or not using various types of ventilation systems and 2) developing alternative approaches to achieving acceptable levels of ventilation while avoiding the risks associated with super-tight home enclosures and potential mechanical system failures. The report includes discussions of pertinent airtightness and mechanical ventilation topics and provides recommended ventilation practices for Florida.

Redox Stable Anodes For Solid Oxide Fuel Cells, Guoliang Xiao, Fanglin Chen

Faculty Publications

Solid oxide fuel cells (SOFCs) can convert chemical energy from the fuel directly to electrical energy with high efficiency and fuel flexibility. Ni-based cermets have been the most widely adopted anode for SOFCs. However, the conventional Ni-based anode has low tolerance to sulfur-contamination, is vulnerable to deactivation by carbon build-up (coking) from direct oxidation of hydrocarbon fuels, and suffers volume instability upon redox cycling. Among these limitations, the redox instability of the anode is particularly important and has been intensively studied since the SOFC anode may experience redox cycling during fuel cell operations even with the ideal pure hydrogen as …

Flexible Residential Test Facility: Impact Of Infiltration And Ventilation On Measured Cooling Season Energy And Moisture Levels, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

Air infiltration and ventilation in residential buildings is a very large part of the heating loads, but empirical data regarding the impact on space cooling has been lacking. Moreover, there has been little data on how building tightness might relate to building interior moisture levels in homes in a hot and humid climate. To address this need, BA-PIRC has conducted research to assess the moisture and cooling load impacts of airtightness and mechanical ventilation in two identical laboratory homes in the hot-humid climate over the cooling season.

Economic, Energy And Ghg Emissions Performance Evaluation Of A Whispergen Mk Iv Stirling Engine Μ-Chp Unit In A Domestic Dwelling, Gerry Conroy, Aidan Duffy, Lacour Ayompe

Articles

This paper presents an assessment of the energy, economic and greenhouse gas emissions performances of a WhisperGen Mk IV Stirling engine μ-CHP unit for use in a conventional house in the Republic of Ireland. The energy performance data used in this study was obtained from a field trial carried out in Belfast, Northern Ireland during the period June 2004 - July 2005 by Northern Ireland Electricity and Phoenix Gas working in collaboration with Whispertech UK. A comparative performance analysis between the µ-CHP unit and a condensing gas boiler revealed that the µ-CHP unit resulted in an annual cost saving of …

Investigation Of Boiling Performance Of Graphene-Coated Surfaces, Daniel C. Stack

Renée Crown University Honors Thesis Projects - All

In this Capstone Project, I sought to investigate the boiling performance of graphene-coated surfaces. Boiling was accomplished in a pool boiling chamber, with samples of graphene-coating SiO₂ wafers. I developed a procedure for graphene transfer for sample fabrication. Samples were prepared with graphene grown on copper substrates by chemical vapor deposition (CVD). Graphene was transferred from copper substrates to SiO­₂ wafers by a thermal release transfer tape. Copper was etched away from the tape-graphene combination by ferric chloride, and the tape was peeled away after heating, leaving graphene on the SiO₂ substrate. Contact angles were measured to …

Bellevue-Santa Fe Charter School Solar Panel Project, Dulce Arroyo Martinez, Henrik Lee, Moises Quiroz, Timothy Iafrate

Mechanical Engineering

This project covers the design, manufacture, and installation of solar panel frames on a charter school in Avila Beach, CA. Through preliminary research regarding important factors (such as solar movement, ideal panel angle, and site-specific factors), a frame that meets the standards set forth in the California Building Codes was designed. After approval by presiding authorities, parts specified in the design were ordered, inspected upon arrival, and manufactured to the design as necessary. Much of the challenge was related to the installation aspect of the project—coordination with the proper authorities and correct submission of applications was integral to the success …

Anisotropy Of The Reynolds Stress Tensor In The Wakes Of Counter-Rotating Wind Turbine Arrays, Nicholas Michael Hamilton

Dissertations and Theses

A wind turbine array was constructed in the wind tunnel at Portland State University in a standard Cartesian arrangement. Configurations of the turbine array were tested with rotor blades set to rotate in either a clockwise or counter-clockwise sense. Measurements of velocity were made with stereo particle-image velocimetry. Mean statistics of velocities and Reynolds stresses clearly show the effect of direction of rotation of rotor blades for both entrance and exit row turbines. Rotational sense of the turbine blades is visible in the mean spanwise velocity W and the Reynolds shear stress -[macron over vw]. The normalized anisotropy tensor was …