Energy Systems Commons^™

Sustainability Matchmaking: Exploration Into Using Excess Renewable Energy To Deliver ‘Free’ Energy To Fuel Poor Homes – A Preliminary Case Study In Ireland, Ciara Ahern, Ronan Oliver

Articles

The aggregated fuel cost of domestic hot water (DHW) generation in Ireland, in 2022, was €529M with associated emissions/load of 1.3MtCO₂/289GWh. The shadow price of carbon monetises the negative impact of emissions, rising with time; DHW generation has an associated shadow carbon cost of €13M in 2022, rising to €42M in 2030 and €335M in 2050.

In 2020, c12%/€441M of wind was curtailed or wasted as inter alia, there was no demand at times of high wind. Meanwhile, a ‘silent crisis’ is occurring in Ireland wherein one-in-two dwellings were considered in fuel poverty in 2022. Households in …

Addressing Low Heat Pump Heating System Sales In The Uk, Ben Costelloe

Articles

The replacement of existing fossil fuel boilers with heat pumps is seen as a key measure in the decarbonisation of heating systems and addressing climate change. This policy however, is currently failing in many Western European states, particularly in the UK. The many reasons for this situation are examined. However, the age of UK housing stock and particularly the high number of dwellings built prior to the introduction of building insulation regulations in 1980, are key. To maintain the running cost of air source heat pumps competitive with those of the gas boilers they generally replace the heat pump lift …

Energy-Specific Greenhouse Gas Emissions Measurements From 2-Stroke Marine Diesel Engine Using Liquefied Natural Gas, Kang-Ki Lee, Wilfried Hochegger, Alessandro Schonborn

Articles

This study reports the energy specific air emissions from a diesel-cycle high pressure injection dual fuel engine for operation on liquefied natural gas and heavy fuel oil. An experiment at sea was performed onboard a bulk carrier during commercial voyages, to measure the efficiency of the engine and to measure air emissions relevant to air pollution and climate impact for operation on both fuels. The measurements showed that the energy conversion efficiency of the engine was higher for operation on liquefied natural gas because its lower NOx emissions permitted the use of a higher effective compression ratio whilst meeting the …

Tidal Current Turbine Blade Optimisation With Improved Blade Element Momentum Theory And A Non-Dominated Sorting Genetic Algorithm, Eng Jet Yeo, David Kennedy, Fergal O'Rourke

Articles

Tidal current energy has the advantage of predictability over most of the other renewable energy resources. However, due to the harsh operating environment and complicated site conditions, developments in this domain have been gradual. Paramount to these points is device design and optimisation of hydrodynamic performance. Recent developments in the correction models of BEM theory have further improved the accuracy of the prediction model. Using an improved blade element momentum theory model that is capable of accurately capturing the downwash angle and combining it with a well-developed and reliable non-dominated sorting genetic algorithm model, an effective and efficient tidal current …

Building Performance - Societal Drive, Programme And Symposium, Joseph Little, Patrick Daly

Articles

Society is increasingly looking at the construction industry to mitigate the environmental crisis and solve the housing crisis through wholesale embrace of three broad sets of challenges. The MSc in Building Performance (Energy Efficiency in Design) (MSc BP(EED)) was created in 2017 to provide significant upskilling in the knowledge, skills, and software applications of building design professionals so that they can meet these challenges, while creating compliant, sustainable, super-low energy, new and renovated buildings. The delivery of the programme supports upskilling of employed building design professionals at Masters level, encouraging a minority to develop their capacity and interest in research …

The Application Of Evolutionary Algorithms In Multi-Objective Design And Optimization Of Air Cooled Heatsinks, Younis Osama Abdelsalam, Sajad Alimohammadi, Tim Persoons

Articles

Genetic algorithms (GAs) are considered to be one of the main types of evolutionary algorithms (EAs) and are being increasingly used in various engineering design applications. To a large extent, plate-fin heatsinks are used in the thermal management of compact electronic equipment and data centers. The shape optimization of the heatsinks is not rigorously investigated during the design process of high power electronics. Any improvements in the effectiveness of the heatsinks impact the energy consumed by large-scale information communication technology (ICT) facilities including data centers and telecommunication systems and promote a more sustainable use of raw materials. This paper investigates …

Carbon-Based Interlayers In Perovskite Solar Cells, Aleksandr P. Litvin, Xiaoyu Zhang, Kevin Berwick, Anatoly V. Fedorov, Weitao Zheng, Alexander V. Baranov

Articles

Perovskites are solution-processed, high-performance semiconductors of interest in low-cost photovoltaics. The interfaces between the perovskite photoactive layers and the top and bottom contacts are crucial for efficient charge transport and minimizing trapping. Control of the collection of charge carriers at these interfaces is decisive to device performance. Here, we review recent progress in the realization of efficient perovskite solar cells using cheap, easily processed, stable, carbon-based interlayers. Interface materials including graphene, carbon nanotubes, fullerenes, graphene quantum dots and carbon dots are introduced and their influence on device performance is discussed.

Energy Performance Certification: Misassessment Due To Assuming Default Heat Losses, Ciara Ahern, Brian Norton

Articles

Energy Performance Certificates (EPCs) are issued when dwellings are constructed, sold or leased in the EU. Where the cost of obtaining the required data is prohibitive, EPC assessors use nationally applicable default-values. To ensure that dwellings are not assigned a wrongly-higher EPC rating, a standardised thermal bridging transmittance coefficient (Y-value) is typically adopted for all existing dwellings while worst-case overall heat loss coefficients (U-values) are used. Default U-values are applied to a specific building element type (roof, wall, floor etc.) based on building codes and regulations applicable at time of construction. Due to significant building fabric upgrades, default U-values are …

A Generalisable Bottom-Up Methodology For Deriving A Residential Stock Model From Large Empirical Databases, Ciara Ahern, Brian Norton

Articles

Specifying representative reference buildings as a prerequisite for calculating cost-optimal energy performance requirements for buildings and building elements. Appropriate characterisation is prerequisite data for an overall national building energy consumption model to produce valid outcomes. Energy Performance Certificates (EPCs) are issued in the EU, for dwellings whenever they are constructed, sold or leased. Where acquiring data for an EPC would be prohibitively costly, nationally applicable default-values are employed for the building envelope thermal transmittance coefficients. Significant levels of retrofits led to the default-values used now being higher than is typical in reality, leading to characterisations of reference dwellings based on …

Thermal Refurbishment Status Of The Irish Housing Stock, Ciara Ahern, Brian Norton

Articles

Energy Performance Certificates (EPCs) are issued for buildings constructed, sold or leased across the EU. Using a generalizable methodology this work exploits Ireland’s EPC national dwelling stock database to determine the thermal refurbishment status of Ireland’s housing stock. It is estimated in 2014 that; i) 58% of walls were insulated at a mean overall heat loss coefficient or U-value of 0.66 W/m 2 K, ii) 67% of roofs were insulated at a mean U-value 0.37 W/m 2 K, iii) 97% of windows were double-glazed, and iv) 53% of floors were insulated to a mean U-value of 0.59 W/m 2 K. …

A Techno-Economic Analysis Of Current Cooling Techniques In Irish Data Centres, Lee Gibbons, Bryan Coyne, David Kennedy, Sajad Alimohammadi

Articles

This research is part of a comprehensive study to determine reformative actions for cooling regimes within the Irish data centre market. To achieve this goal, preliminary Exergy, Entropy change and operational cost analyses are used. It is determined that there is no clear advantage for using one cooling method over another without knowing the data centres secondary function (e.g. district heating, energy generation). Air cooling technology is a good candidate for a highly reliable system due to the low exhaust temperatures of 30°C. Two-phase immersion is a possibility for economically viable data centres where operational costs are to be minimised, …

A Novel Approach Towards Investigating The Performance Of Different Pvt Configurations Integrated On Test Cells: An Experimental Study, Vivek Tomar, Brian Norton, G. N. Tiwari

Articles

This study elaborates the theoretical and experimental analysis for the effectiveness of different photovoltaic thermal (PVT) configurations along with their building implications. An experiment was performed on especially designed four identical prototype test cells emphasise the building integration photovoltaic thermal (BiPVT) systems. A comparative analysis of four different possible PVT configurations integrated on identical test cells namely; Case 1: Glass-to-glass PV with duct integrated on a test cell, Case 2: Glass-to -glass PV without duct integrated on a test cell, Case 3: Glass to tedlar PV with duct integrated on a test cell and Case 4: Glass to tedlar PV …

Calculation Methods Of Radon-222 Radiological Activity For Norm Plant With Ventilation, Pedro M. Dieguez-Elizondo, Paul G. O'Donohoe, Tomas Gil-Lopez, Juan Castejon-Navas, Miguel A. Gálvez-Huerta

Articles

A procedure is proposed to determine the radiological activity of air present in the working area of a NORM (Naturally-Occurring Radioactive Materials) plant. This NORM plant is located in the United Arab Emirates and is dedicated to the recycling of material and equipment used in oil extraction facilities. Substantial quantities of NORM waste will be present inside the enclosed plant facilities and will exhale significant amounts of Radon-222 into the working environment. The continued inhalation of this gas and its progeny has been shown to cause lung cancer. In order to reduce the concentration level of the aforementioned gas to …

Effect Of Sky Conditions On Light Transmission Through A Suspended Particle Device Switchable Glazing, Aritra Ghosh, Brian Norton, Aidan Duffy

Articles

A suspended particle device (SPD) switchable glazing changes its state from opaque to transparent in the presence of a power supply. SPD glazing's near normal transmission varies with incident angle and clearness index. Due to a lower diffuse component, higher glazing transmission ensues at higher clearness indices. Transmittance values for different azimuthal incident angle for a SPD glazing for its “transparent” and “opaque” states have been determined. In Dublin, below 0.5 clearness index, isotropic diffuse transmittance was prevailed while transmission of direct insolation was dominant above 0.5 clearness index. For south facing vertical plane SPD glazing transmittance in its transparent …

Behaviour Of A Spd Switchable Glazing In An Outdoor Test Cell With Heat Removal Under Varying Weather Conditions, Aritra Ghosh, Brian Norton, Aidan Duffy

Articles

Suspended particle device (SPD) switchable glazing has potential to control transmission of solar radiation in the visible range by changing its transparency from 55% to 5%. Outdoor test cell characterisation of a SPD switchable glazing offered the dynamic solar heat gain coefficient (SHGC) which varied between 0.05 (when opaque) and 0.38 (when transparent). Reduction of maximum temperature rise of 11% and 15% was possible using SPD “transparent” and “opaque” state compared to same area double-glazing. Insulated test cell with water flow heat exchanger was employed to measure the cooling load reduction potential of SPD glazing while its transmission changed from …

Thermodynamic Analysis Of Closed Steady Or Cyclic Systems, Jim A. Mcgovern

Articles

Closed, steady or cyclic thermodynamic systems, which have temperature variations over their boundaries, can represent an extremely large range of plants, devices or natural objects, such as combined heating, cooling and power plants, computers and data centres, and planets. Energy transfer rates can occur across the boundary, which are characterized as heat or work. We focus on the finite time thermodynamics aspects, on energy-based performance parameters, on rational efficiency and on the environmental reference temperature. To do this, we examine the net work rate of a closed, steady or cyclic system bounded by thermal resistances linked to isothermal reservoirs in …

Energy Savings Across Eu Domestic Building Stock By Optimizing Hydraulic Distribution In Domestic Space Heating Systems, Ciara Ahern, Brian Norton

Articles

The objective of this work is to quantify the resultant savings across the EU from the optimization of existing system components in domestic space heating distribution systems to maintain comfort levels. Heat energy savings are shown to range from 1% to 19% depending on dwelling type, age, location and initial specific heat energy consumption.

Process Simulation Of Biomass Gasification Integrated With A Solid Oxide Fuel Cell Stack, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

Biomass gasification-solid oxide fuel cell (BG-SOFC) combined heat and power (CHP) systems are of major interest in the context of climate change mitigation, energy security and increasing energy efficiency. Aspen Plus is employed to simulate various BG-SOFC CHP systems. The aim of the research work is to investigate the technical feasibility of these systems and to study the influence of important operating parameters and examine integration options. Systems based on dual fluidised bed steam gasification and tubular SOFC technologies are modelled. The cathode recycle and electric heater integration options are not attractive in comparison to the base case anode recycle …

Economic, Energy And Ghg Emissions Performance Evaluation Of A Whispergen Mk Iv Stirling Engine Μ-Chp Unit In A Domestic Dwelling, Gerry Conroy, Aidan Duffy, Lacour Ayompe

Articles

This paper presents an assessment of the energy, economic and greenhouse gas emissions performances of a WhisperGen Mk IV Stirling engine μ-CHP unit for use in a conventional house in the Republic of Ireland. The energy performance data used in this study was obtained from a field trial carried out in Belfast, Northern Ireland during the period June 2004 - July 2005 by Northern Ireland Electricity and Phoenix Gas working in collaboration with Whispertech UK. A comparative performance analysis between the µ-CHP unit and a condensing gas boiler revealed that the µ-CHP unit resulted in an annual cost saving of …

The Effects Of Physical Activity On Greenhouse Gas Emissions For Common Transport Modes In European Countries, Aidan Duffy, Robert Crawford

Articles

This paper applies a life cycle methodology to estimate activity-related contributions of transport modes to GHG emissions. The methodology uses national input-output tables, environmental accounts, household budget data and nutritional data to derive food-sector GHG coefficients of consumption for ten European countries. The food energy requirements for each mode of transport are estimated taking account of the modal activity level and energy requirements. Walking, cycling, driving and bus travel are considered. Typical national food energy-related emissions for walking, cycling, and driving ranged from 25.6 - 77.3 gCO2-eq/pass.km, 10.4 - 31.4 gCO2-eq/pass.km and 1.7 - 5.2 gCO2-eq/pass.km; passenger transport was found …

State Of The Irish Housing Stock - Modelling The Heat Losses Of Ireland’S Existing Detached Rural Housing Stock & Estimating The Benefit Of Thermal Retrofit Measures On This Stock, Ciara Ahern, Philip Griffiths, Micheal O'Flaherty

Articles

Ireland’s housing stock has been identified as being amongst the least energy efficient in Northern Europe. Consequently, atmospheric emissions are greater than necessary. Government funded schemes have been introduced to incentivise the uptake of thermal retrofit measures in the domestic Irish market. A study of Ireland’s housing highlights the dominance of detached houses (43%), 72% of which are rurally located and are predominantly heated with fuel oil. This paper investigates the economic and carbon case for thermal retrofit measures to the existing detached, oil centrally heated, rural housing stock. The study found the case for energy efficiency measures to be …

Transient And Quasi-Steady Thermal Behaviour Of A Building Envelope Due To Retrofitted Cavity Wall And Ceiling Insulation, Aimee Byrne, Gerard Byrne, Anna Davies, Anthony Robinson

Articles

Accurate understanding of the thermal behaviour of building components is essential for predicting heat-ing or cooling needs and facilitates the implementation of more successful energy saving strategies and retrofits. This paper focuses on a specific measure commonly introduced through the residential energy efficiency retrofit programmes in Ireland–insulation. Traditionally, assessments of the performance of building envelopes have been based on assumed thermal resistances of the materials involved, labora-tory tests and computer modelling. The aim of the present work is to investigate the in situ thermal behaviour of a case study building and its components under transient and quasi-steady environmental conditions, comparing …

Technical Note: Friction Factor Diagrams For Pipe Flow, Jim Mcgovern

Articles

This technical note describes diagrams of friction factor for pipe flow that have been prepared using, mainly, the equations that Lewis Moody used to prepare his famous diagram in 1944. The preparation of the new diagrams was prompted by the need for vector graphics versions that could be used for teaching purposes and that could be distributed freely to students and others under a Creative Commons Attribution-Share-Alike license. Using a structure very similar to that of Moody's diagram, variants with the Darcy friction factor and the Fanning friction factor have been prepared. In addition, variants have been prepared that include …

Some Experiences, Thoughts, Ideas And Open Questions Relating To Applied Thermodynamics, Jim Mcgovern

Articles

In this paper I present some of my thoughts and experiences relating to 'applied thermodynamics' over my career so far. I explain my interest in thermodynamics, describe some topics I have worked on, point out some questions that appear still to be open and outline some ideas for work that could be done. I describe how I was inspired to pursue the area of applied thermodynamics, with reference to a glass, opposed-piston internal combustion engine. I put my heat pump research in the late 1970s briefly into today's context. Some of my research has been in relation to compressors, which …

Computer Simulation Of A Biomass Gasification-Solid Oxide Fuel Cell Power System Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

The operation and performance of a solid oxide fuel cell (SOFC) stack on biomass syn-gas from a biomass gasification combined heat and power (CHP) plant is investigated. The objective of this work is to develop a model of a biomass-SOFC system capable of predicting performance under diverse operating conditions. The tubular SOFC technology is selected. The SOFC stack model, equilibrium type based on Gibbs free energy minimisation, is developed using Aspen Plus. The model performs heat and mass balances and considers ohmic, activation and concentration losses for the voltage calculation. The model is validated against data available in the literature …

Simulation Of A Tubular Solid Oxide Fuel Cell Stack Operating On Biomass Syngas Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

A tubular solid oxide fuel cell (SOFC) stack was modelled and its operation on biomass syn-gas was investigated. The objective of this work was to develop a computer simulation model of a biomass gasification-SOFC (BG-SOFC) system capable of predicting performance under various operating conditions and using diverse fuels. The stack was modelled using Aspen Plus and considers ohmic, activation and concentration losses. It was validated against published data for operation on natural gas. Operating parameters such as fuel and air utilisation factor U_f and U_a, current density j and steam to carbon ratio STCR were varied and …

Marine Current Energy Devices: Current Status And Possible Future Applications In Ireland, Fergal O'Rourke, Fergal Boyle, Anthony Reynolds

Articles

There is a growing demand for the use of renewable energy technologies to generate electricity due to concerns over climate change. The oceans provide a huge potential resource of energy. Energy extraction using marine current energy devices (MCEDs) offers a sustainable alternative to conventional sources and a predictable alternative to other renewable energy technologies. A MCED utilises the kinetic energy of the tides as opposed to the potential energy which is utilised by a tidal barrage. Over the past decade MCEDs have become an increasingly popular method of energy extraction. However, marine current energy technology is still not economically viable …

Tidal Energy Update 2009, Fergal O'Rourke, Fergal Boyle, Anthony Reynolds

Articles

Tidal energy has the potential to play a valuable part in a sustainable energy future. It is an extremely predictable energy source, depending only on the gravitational pull of the moon and the sun and the centrifugal forces created by the rotation of the earth-moon system. Tidal energy has been exploited on a significant scale since the construction of the La Rance tidal barrage in France in 1967. A tidal barrage utilises the potential energy of the tide and has proven to be very successful, despite opposition from environmental groups. Kinetic energy can also be harnessed from tidal currents to …

Heat Transfer Correlations For Low Approach Evaporative Cooling Systems In Buildings, Ben Costelloe, Donal Finn

Articles

The experimental performance of an open industrial scale cooling tower, utilising small approach temperature differences (1–3 K), for rejection of heat at the low water temperatures (11–20 °C) typical of chilled ceilings and other sensible air–water heat dissipation systems in buildings, is examined. The study was carried out under temperate maritime climatic conditions (3–18 °C wet-bulb temperature range). Initially a theoretical analysis of the process at typical conditions for this climate was conducted, which indicated that a water to air (L/G) mass flow rate ratio of less than 1.0 was required for effective operation. Consequently for these low L/G ratios, …

Renewable Energy Resources And Technologies Applicable To Ireland, Fergal O'Rourke, Fergal Boyle, Anthony Reynolds

Articles

The energy consumed in Ireland is primarily achieved by the combustion of fossil fuels. Ireland’s only indigenous fossil fuel is peat; all other fossil fuels are imported. As well as fossil fuels continually becoming more expensive, their use as an energy source also has a negative impact on the environment. Ireland’s energy consumption can be separated into 3 divisions; transportation, electricity generation and heat energy. Ireland however has a vast range of high quality renewable energy resources. Ireland has set a target of 33% of its electricity will be generated from renewable sources by 2020[1]. The use of biomass, wind …