Computer-Aided Engineering and Design Commons^™

A Parametric Computational Fluid Dynamics (Cfd) Study Of In-Line Horizontal Axis Wind Turbines (Hawts) With Yaw, North Alyster Yates

Masters Theses

Because of the constant use of non-renewable fossil fuels, and the enormous impact they have on global warming and pollution, there has been a push to use more eco-friendly and renewable sources for power. One such form is wind power via turbines. The most common form, Horizontal Axis Wind Turbines (HAWTs), can generate massive amounts of power. However, they also have a serious flaw in their design. As the wind passes through the swept area of the blades and past the tower, it creates massive disturbances in the airflow. These disturbances are called a ‘wake’. When trying to create a …

The Development Of A Finite Element Model For Ballistic Impact Predictions, Richard Allen Perkins

Theses and Dissertations

Concrete is a widely used product and is an important application throughout industry due to its inexpensive cost and wide range of applications. This work focuses on understanding the behavior of high strength concrete in high strain rate ballistic impact loading scenarios. A finite element analysis was created with the implementation of the Concrete Damage and Plasticity Model 2 (CDPM2) to represent the material behavior. The model’s parameters were calibrated to existing literature and the results were analyzed by a comparison of the impact velocity to residual velocity and a qualitative assessment of the impact crater. The model captured the …

Process Improvement Of Honeysuckle Biscuits And Bakery, Jevon Franklin, Kaela Bellamy, Manuel Quintal, Suheyl Polat

Senior Design Project For Engineers

Honeysuckle Biscuits and Bakery is a locally owned restaurant in Downtown Kennesaw, Georgia. Mitch and Lori Phillips, the owners, opened the restaurant in 2018. The restaurant serves breakfast (with biscuits as its specialty), lunch, coffee, desserts, and specialty cakes. As the business is beginning to outgrow itself, the project manager, Kaela Bellamy, felt it was a need to look at how to best accommodate the growing demand within the new space.

Deep Learning Strategies For Pool Boiling Heat Flux Prediction Using Image Sequences, Connor Heo

Graduate Theses and Dissertations

The understanding of bubble dynamics during boiling is critical to the design of advanced heater surfaces to improve the boiling heat transfer. The stochastic bubble nucleation, growth, and coalescence processes have made it challenging to obtain mechanistic models that can predict boiling heat flux based on the bubble dynamics. Traditional boiling image analysis relies on the extraction of the dominant physical quantities from the images and is thus limited to the existing knowledge of these quantities. Recently, machine-learning-aided analysis has shown success in boiling crisis detection, heat flux prediction, real-time image analysis, etc., whereas most of the existing studies are …

Mission Profile Effects On Automotive Drivetrain Electronics Reliability: Modeling And Mitigation, Bakhtiyar Mohammad Nafis

Graduate Theses and Dissertations

The reliability of electronic devices is dependent upon the conditions to which they are subject. Temperature variations coupled with differences in thermal expansion between bonded materials results in thermomechanical stresses to build up, which can instigate failure in the interconnects or other critical regions. With the move towards electrification in the automotive industry, there is the increasingly important consideration of powertrain electronics reliability, the pertinent conditions being governed by the drive cycle or mission profile of the vehicle. The mission profile determines the power dissipated by the electronic devices, which determines the peak and mean temperature, temperature swing and the …

Respiratory Compensated Robot For Liver Cancer Treatment: Design, Fabrication, And Benchtop Characterization, Mishek Jair Musa

Graduate Theses and Dissertations

Hepatocellular carcinoma (HCC) is one of the leading causes of cancer-related death in the world. Radiofrequency ablation (RFA) is an effective method for treating tumors less than 5 cm. However, manually placing the RFA needle at the site of the tumor is challenging due to the complicated respiratory induced motion of the liver. This paper presents the design, fabrication, and benchtop characterization of a patient mounted, respiratory compensated robotic needle insertion platform to perform percutaneous needle interventions. The robotic platform consists of a 4-DoF dual-stage cartesian platform used to control the pose of a 1-DoF needle insertion module. The active …

Printed Circuit Board Design And Layout For Hobbyists, Engineers, And Students, Michael A. Derrenbacher

Master's Theses

Printed Circuit Boards (PCBs) are a ubiquitous element of virtually every electronic system manufactured world-wide. It is not a stretch of the imagination to say that if it’s electronic, there is a PCB in it. PCBs are necessary tools for electronics work, and tools need to have instructions. For better or worse, PCB knowledge is a deep and wide ocean. There is much to cover for even a surface level understanding, and there are deep areas rich in technical expertise. Navigating the ocean of knowledge is treacherous; common knowledge of yore can be downright dubious now. PCB manufacturing and electronics …

Automated Mini-Tubular Ceramic Production, Hunter Brooks, Daniel Freeman, Leo Taranta-Slack

Mechanical Engineering

Researchers at Lawrence Livermore National Laboratory need a way to increase the rate of manufacturing of mini-tubular ceramics to be used in testing particulate air filters. This document outlines our process from researching and writing an initial scope of work all the way to fabricating and testing a final prototype. This journey takes us through the background research, ideation process and selection of a final design. We also detail the desired engineering specifications and our concept selection process. We dedicate a significant portion of this report to discussion of our final design. We delve into how it was manufactured as …

Digital Design And Thermomechanical Process Simulation For 3d Printing With Abs And Soyhull Fibers Reinforced Abs Composites., Saleh Khanjar

Electronic Theses and Dissertations

Recent demonstrations with fused filament fabrication (FFF) 3D printing have shown to produce prototypes as well as production components. Additionally, due to the FFF process platforms being low-cost and readily available there has been a high-demand to produce on-demand parts for various applications in automotive, in-space manufacturing and electronic industries. However, current limitations such as limited availability of advanced composites materials, and guidelines for design-for-manufacturing make the process prone to trial-and-error experiments both at the materials development, product design and manufacturing stage. In this work, new thermomechanical process simulations platform, Digimat-AM has been evaluated to address and demonstrate digital design …

Design Of A 300cm2 Pemfc Stack With Force And Cfd Simulation To Optimize Flow Channels, Gasket Design, And Clamping Forces., Robert M. Ench

Electronic Theses and Dissertations

Proton exchange membrane fuel cells are important to the future of green energy as hydrogen can be made with green technologies and store energy for later use. Fuel cells can efficiently convert the hydrogen to electricity as needed. This study uses Solidworks simulation to make design improvements to the fuel cell before the prototype build stage of testing; this saves money and time by reducing the prototype builds needed.

In this study, a multi-channel serpentine design with two outlets versus a single outlet is evaluated using CFD to investigate pressure drop. Lower pressure drops are desirable as less energy input …

Product Lifecycle Management - Application Of Patterning Methods To Gas Turbine Blades And Creation Of Learning Materials, David Procopio

All Theses

To compete in the global marketplace, companies need to embrace virtual design and manufacturing methods. Product Lifecycle Management (PLM) embodies both the workflow processes and tools to bring forth products from conception to design to fabrication to service to decommissioning, and to eventual recycling. In response to the growing demand for engineers and technicians with these critical skills, colleges and universities should introduce these virtual tools through seminars, software workshops, and computer laboratory sessions. Some of the opportunities in the PLM Center at Clemson University include short courses on PLM practices, focused software training sessions, hands-on exploration activities, and research …

Design And Fabrication Of A Polymer Fdm Printer Capable Of Build Parameter Monitoring And In-Sit Geometric Monitoring Via Photogrammetry, Travis Roberts

All Theses

Additive manufacturing, or 3D printing, is a complex process that creates free-form geometric objects by sequentially placing material in a location to construct an object, usually as a layer-by-layer process. One of the most widespread methods is Fused Deposition Modeling (FDM). FDM is used in many of the consumer-grade polymer 3D printers available today. While consumer grade machines are cheap and plentiful, they lack many of the features desired in a machine used for research purposes and are often closed-source platforms. Commercial-grade models are more expensive and are also usually closed-source platforms that do not offer flexibility for modifications often …

Optimized Tip Cooling Using Am Process, Alberto H. Gamez, Lourdes Sarmiento Martinez, Andrew Van Bogelen

Mechanical Engineering

This Final Design Review (FDR) reports on the senior design project undertaken by our team of mechanical engineering seniors at California Polytechnic State University, San Luis Obispo. This project seeks to use the additive manufacturing process to improve the existing design of a Taurus 60 gas turbine injector tip. The current injector tip is owned by Solar Turbines, a designer and manufacturer of gas turbines for electric generation, propulsion, as well as natural resource transportation. The challenge at hand is to design a new injector tip that will be reliable for at least 60,000 hours and provide ease of replacement, …

Mechanical Interfacial Locking And Multiscale Modeling Of Reinforced Thermoplastic Composites For Structural Applications, Anmol Kothari

All Dissertations

The ever-growing pressure of reducing the adverse impact of transportation systems on environment has pushed industries towards fuel-efficient and sustainable solutions. While several approaches have been used to improve fuel efficiency, the light-weighting of structural components has proven broadly effective. In this regard, reinforced thermoplastic composites (RTPC), owing to their high recyclability, higher impact strength and fast cycle times, have become competitive candidates at an industrial scale. However, to implement RTPC toward large scale structural applications several challenges pertaining to material design and manufacturing effects need to be addressed. To this end, a computational study is carried out to address …

The Effect Of Bit Depth On High Temperature Digital Image Correlation Measurements, Steven Robert Jarrett

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Digital Image Correlation (DIC) is a camera-based method of measuring mechanical displacement and strain which is commonly used in high-temperature experiments due to its ability to take contactless measurements. High-temperature DIC is challenging due to light emitted from the sample which can saturate the camera sensor. Blue-DIC and UV-DIC have been developed to minimize this effect, but the maximum sample temperature range of DIC remains a function of the camera and camera settings. Bit depth, also referred to as color depth or number of bits, is an important camera setting which affects the dynamic range of an image, but which …

Additive Manufacturing Of Cork, A Cold Spray Technology, Kimberly Kay Dickey

Theses and Dissertations

Cold Spray Additive Manufacturing is a technology capable of mass manufacturing components with complicated geometry and coating substrates in hard-to-reach areas. In addition, cold spray also has the ability of conducting a green manufacturing process, with zero waste of renewable feed material, and zero gas and chemical emission. This paper investigates solely cold spray as an additive manufacturing technology with cork as the natural material. CFD results were used to predict the physical behavior of air and the cork particles. After unsuccessful coatings, final results showed that when moisture is added, cork is successfully cold sprayed, and agglomeration is experienced. …

Creating Reel Designs: Reflecting On Arthrogryposis Multiplex Congenita In The Community, Iris Layadi

Purdue Journal of Service-Learning and International Engagement

Because of its extreme rarity, the genetic disease arthrogryposis multiplex congenita (AMC) and the needs of individuals with the diagnosis are often overlooked. AMC refers to the development of nonprogressive contractures in disparate areas of the body and is characterized by decreased flexibility in joints, muscle atrophy, and developmental delays. Colton Darst, a seven-year-old boy from Indianapolis, Indiana, was born with the disorder, and since then, he has undergone numerous surgical interventions and continues to receive orthopedic therapy to reduce his physical limitations. His parents, Michael and Amber Darst, have hopes for him to regain his limbic motion and are …

Rip Curl: Community Activism For The Coast (The Ux Phase, Rip Curl And Sustainability, The Ui Phase), John Delacruz

Assignment Prompts

ADV 132 enables students to explore the craft and process of user experience and user interface design. They develop their skills within the context of a specific brief. The aim is to offer students the opportunity to immerse themselves in a particular problem and come up with creative solutions that will come to life on digital media platforms.

Build Your Own Body Mod: Empowerment Through Prototyping And Design, Anaiss Arreola, Katherine R. Ganim

Journal of Science Education for Students with Disabilities

When you don’t have a hand, what could you have instead? This article introduces the impact of inviting youth with disabilities to learn tools and technology to design their own solutions and advocate for their own future. This approach to programming is rooted in a mindset of designing WITH, not FOR. Not only are design outcomes improved when users are incorporated into the process, but this approach has been shown to improve confidence in creating one’s own solutions. These programs include hands-on “design-your-own-body-mod” workshops, as well as a budding inclusive design consultancy led by youth with disabilities. Through this programming, …

Design And Development Of A Novel Soft Gripper Manipulated By A Robotic Arm, Derek Price

Symposium of Student Scholars

This study presents the design and development of a tendon-driven soft gripper manipulated by a 4 DOF robotic arm. The proposed robotic arm and the gripper explore the new areas focusing on increasing the grasping performance of the gripper as well as the workspace. The gripper is designed as a 3 finger and driven by tendons using two servo motors. The tension of the strings is adjusted using a pulley mechanism and a string. The opening and grasping of the soft gripper are accomplished by each motor. The wide opening allows the gripper to grasp wide objects. The parallel robotic …

Atomistic Simulation Of Desalination, Ian David Durr

Symposium of Student Scholars

Atomistic Simulation of Desalination

Ian Durr, Matheus Prates, and Jungkyu Park

Kennesaw State University

In this research, we investigate the desalination capacity of three-dimensional (3D) carbon nanostructures using molecular dynamics simulations. 3D carbon nanostructures proposed here will filter seawater efficiently because of their multiple layers with holes of tunable sizes. The structure is designed to be flexible, allowing mechanical deformation during daily use. The 3D carbon nanostructure will still possess high thermal conductivity, enabling easy recycle through a simple heating process. Here, we employ LAMMPS, Large-scale Atomic/MolecularMassively Parallel Simulator distributed by Sandia National Laboratories to measure salt ion flux through …

Using Comprehensive Finite Element Analysis To Simulate A Special Connection In Post-Tensioned Concrete, Joshuah Leljedal

Symposium of Student Scholars

Finite element analysis (FEA) uses differential equations to determine a computer-based solution that explains interactive behaviors within models of complex structural and mechanical systems, subjected to various loading and environmental conditions. Those systems are partitioned into finite elements consisting of a linear mesh with nodes at each end point, and FEA determines relationships, such as force-displacement, between each of the finite elements. This apportioned model allows systems to be evaluated under multiple loading scenarios. Computer-based FEA offers significant benefits that reduce cost and the time required to perform alternative analysis for complex structural systems. In this research project, a comprehensive …

Laser Surface Treatment And Laser Powder Bed Fusion Additive Manufacturing Study Using Custom Designed 3d Printer And The Application Of Machine Learning In Materials Science, Hao Wen

LSU Doctoral Dissertations

Selective Laser Melting (SLM) is a laser powder bed fusion (L-PBF) based additive manufacturing (AM) method, which uses a laser beam to melt the selected areas of the metal powder bed. A customized SLM 3D printer that can handle a small quantity of metal powders was built in the lab to achieve versatile research purposes. The hardware design, electrical diagrams, and software functions are introduced in Chapter 2. Several laser surface engineering and SLM experiments were conducted using this customized machine which showed the functionality of the machine and some prospective fields that this machine can be utilized. Chapter 3 …

Flow Characterization In Mine Ventilation Fan Blade Design Using Cfd, Anwar Endris Hassen

Journal of Sustainable Mining

In axial ventilation fans, the generation of a uniform flow velocity is desirable for better efficiency. To that end, different fan blade types have been developed to achieve better flow uniformity. This article aimed to characterize the flow distribution and its uniformity in four blade designs, namely constant chord, tapered blade, skewed blade, and tapered skewed blade, using Computational Fluid Dynamics (CFD). The study employs an iterative study where key study decisions are made as the study progresses. The study began with the selection of a blade profile for the study. A comparative study between the NACA seven-digit and four-digit …

Geometrically Complex Planar Heat Exchangers, Derli Dias Do Amaral Junior, Jose Lage

Mechanical Engineering Research Theses and Dissertations

In this study, geometrically complex planar heat exchangers, designed in line with the Constructal Law and operating at steady-state, are investigated numerically. The work is divided into two parts, one focusing on diffusion heat transfer in a rectangular plane and another on conjugate diffusion-convection heat transfer in a circular plane heat exchanger.

In the first part, a heat generating rectangular solid volume made of a low conductivity material is cooled through a small, isothermal side-section of the domain. The diffusion cooling process is improved by distributing within the heat generating material a fixed amount of a high conductivity material. The …

A Manufacturing-To-Response Pathway For Formed Carbon Fiber Reinforced Polymer Composite Structures, Madhura Limaye

All Theses

Over the past decade, there has been an increased adoption of thermoplastic and thermoset based continuous carbon fiber reinforced polymer (CFRP) composites for structural applications in several industries. Among the different manufacturing methods, thermoforming process for thermoplastic based continuous CFRP’s offer a major advantage in reducing cycle times for large scale productions. Similarly, out-of-autoclave curing process for thermoset based continuous CFRP’s using heated tooling enables production of large composite structures. However, these manufacturing processes can have a significant impact on the structural performance of parts by inducing undesirable effects. These effects include inhomogeneous fiber orientations, thickness variations, and residual stresses …

Socio-Technical Perspective For Electronic Tax Information System In Tanzania, Lucas Ngowi, Ellen Kalinga

Tanzania Journal of Engineering and Technology (TJET)

Socio-technical systems theory has rarely been used by system architects in setting up computing systems. However, the role of socio-technical concepts in computing, which is becoming social in nature, has made the concepts more relevant and commercial. Tax information systems are examples of such systems because they are influenced by external variables such as the political environment, technological trends, and social environment, introducing complexity in their deployment and determining the type of e-services and their delivery to a diverse group of people. It was observed that in Tanzania there is resistance, reluctance and minimal use of electronic tax system because …

Material Detection With Thermal Imaging And Computer Vision: Potentials And Limitations, Jared Poe

Graduate Theses and Dissertations

The goal of my masters thesis research is to develop an affordable and mobile infraredbased environmental sensoring system for the control of a servo motor based on material identification. While this sensing could be oriented towards different applications, my thesis is particularly interested in material detection due to the wide range of possible applications in mechanical engineering. Material detection using a thermal mobile camera could be used in manufacturing, recycling or autonomous robotics. For my research, the application that will be focused on is using this material detection to control a servo motor by identifying and sending control inputs based …

Computational Frameworks For Multi-Robot Cooperative 3d Printing And Planning, Laxmi Prasad Poudel

Graduate Theses and Dissertations

This dissertation proposes a novel cooperative 3D printing (C3DP) approach for multi-robot additive manufacturing (AM) and presents scheduling and planning strategies that enable multi-robot cooperation in the manufacturing environment. C3DP is the first step towards achieving the overarching goal of swarm manufacturing (SM). SM is a paradigm for distributed manufacturing that envisions networks of micro-factories, each of which employs thousands of mobile robots that can manufacture different products on demand. SM breaks down the complicated supply chain used to deliver a product from a large production facility from one part of the world to another. Instead, it establishes a network …

Anisotropic Plasticity Modeling Of Thin Sheets And Its Application To Micro Channel Forming Of Steel Foils, Jie Sheng

Mechanical Engineering Research Theses and Dissertations

Thin sheet metals and ultrathin metal foils produced by industrial rolling processes are textured polycrystalline materials and their mechanical behaviors may depend strongly on the orientation of applied loading. Consideration of such plastic anisotropy in advanced modeling of these materials is of the paramount importance in designing optimal manufacturing processes for automotive and other applications using finite element methods. This research addresses several critical issues in anisotropic plasticity modeling and its applications in analyzing micro channel forming of ultrathin stainless-steel foils. An experimental study has first been carried out on the accuracy and sensitivity of measuring the plastic strain ratios …