Computer-Aided Engineering and Design Commons^™

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

LSU New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Micro-Architectured Metamaterials: Design And Analysis, Li Ai

Mechanical Engineering Research Theses and Dissertations

Metamaterials are engineered materials with unusual properties deriving mainly from their micro-architectures rather than composition. They have attracted increasing attention owing to their tailorable multi-functional properties that cannot be exhibited by naturally-occurring or traditionally-manufactured materials. Materials with a negative Poisson’s ratio (PR) and materials with a non-positive coefficient of thermal expansion (CTE) are examples of mechanical metamaterials. In this dissertation, metamaterials with negative Poisson’s ratios and negative coefficients of thermal expansion are designed using both heuristic approaches and topology optimization methods.

Firstly, based on a star-shaped re-entrant structure, three two-dimensional (2-D) periodic cellular materials are developed, which can be tailored …

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Exploring Energy, Comfort, And Building Health Impacts Of Deep Setback And Normal Occupancy Smart Thermostat Implementation, Zachary Ethan Alderman

Graduate Theses and Dissertations

As smart thermostat adoption rates continue to increase, it becomes worthwhile to explore what unanticipated outcomes may result in their use. Specific attention was paid to smart thermostat impacts to deep setback and normal occupancy states in a variety of conditions while complying with the ventilation and temperature requirements of ASHRAE 90.2-2013. Custom weather models and occupancy schedules were generated to efficiently explore a combination of weather conditions, building constructions, and occupancy states. The custom modeling approach was combined with previous experimental data within the Openstudio graphics interface to the EnergyPlus building modeling engine. Results indicate smart thermostats add the …

3d Printed Pcu/Uhmwpe Polymeric Blends For Artificial Knee Meniscus, Raissa Araujo Borges

Graduate Theses and Dissertations

3D printing was used to fabricate porous artificial knee meniscus material from biocompatible polymeric blends of polycarbonate-urethane (PCU) and ultra-high-molecular-weight polyethylene (UHMWPE) to enable “weep” lubrication that mimics the native meniscus. 3D printed and molded pure PCU, as well as molded PCU and UHMWPE, were used for comparison. Preliminary printing was done to evaluate the impact of process parameters on the results. The samples were subject to a variety of rotational oscillating friction and wear tests under simulated body fluid and loading conditions to replicate the natural motion of the knee. Results show that 3D printed PCU samples yielded a …

Usa Boccia Ball Ramp For Athletes With Quadriplegia, Alissa A. Koukourikos, Matthew Lee, Nathan Bernards

Mechanical Engineering

In this report, the design process in creating an assistive device for Boccia Classification 3 (BC3) players is outlined. The initial research steps, including research into the rules of the game, capabilities of the players, and existing products is documented to show where ideas for the product stemmed from. This transitions into requirements that the sponsor requested, and preliminary designs and ideas for the product. Finally, this report explains the details of the final design, which has been analyzed for safety, ease of use, and ability to function under different conditions. The processes of manufacturing and testing will also be …

Design, Analysis, And Application Of A Cellular Material/Structure Model For Metal Based Additive Manufacturing Process., Shanshan Zhang

Electronic Theses and Dissertations

Powder bed fusion additive manufacturing (PBF-AM) has been broadly utilized to fabricate lightweight cellular structures, which have promising potentials in many engineering applications such as biomedical prosthesis, aerospace, and architectural structures due to their high performance-to-weight ratios and unique property tailorabilities. To date, there is still a lack of adequate understanding of how the cellular materials are influenced by both the geometry designs and process parameters, which significantly hinders the effective design of cellular structures fabricated by PBF-AM for critical applications. This study aims to demonstrate a cellular structure design methodology that integrates geometrical design and process-material property designs. Utilizing …

Material Properties Design Using Simulations And Experiments For Powder Injection Molding Of Lead Zirconate Titanate (Pzt)., Bhushan Pramod Bandiwadekar

Electronic Theses and Dissertations

Powder injection molding (PIM) process simulations can be performed to minimize the number of injection molding experiments by estimating material properties necessary for PIM simulations. In current work, lead zirconate titanate (PZT) powder-polymer binder feedstock was compounded for 45 vol. % and 52 vol. % solids loading. PIM experiments on designed micro-pillar array geometry were performed using 52 vol. % PZT. Using PIM experiments results as basis, PIM simulations were performed on designed micro-pillar array geometries to understand the effectiveness of PIM simulations with the use of estimated feedstock properties in predicting molding behavior that have micro-features. Additionally, PIM simulations …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Animated Otto-Langen Atmospheric Engine, Keiran M. Hansen, Lance Hodgson, Rachel A. Jakob, Chris J. Splees

Mechanical Engineering

Based on an existing relationship between Dr. Owen and the Deutsches Museum, Otto-Mated was given the opportunity to collaborate with the two in a year-long senior design project. Otto-Mated was tasked with modeling and simulating the Otto-Langen Atmospheric Engine as a form of preservation and education. The model was created in SolidWorks and animated in Blender, effectively providing the museum with accurate and educational videos demonstrating the engine’s function. Within this document are the plans, decisions, and processes used to create our final product for Deutsches Museum.

Answering Food Insecurity: Serving The Community With Food And Knowledge Using Technology, Courtney Simpson

Purdue Journal of Service-Learning and International Engagement

The courses of Tech120, CGT110, and ENGT 180/181 and Red Gold at Purdue collaborated to design a robot that would plant and water a garden for a local community charter school. The students centered the project on the users’ needs for fresh food, nutrition education, and early exposure to STEM for children. The school, Anderson Preparatory Academy (APA), is comprised of many children who come from low-income families and are in the free or reduced lunch program. Inspired from “Farm Bot,” a similar system that allows for almost hands-free gardening, the “Boiler Bot” is designed to be scalable so children …

Cam-Based Pose-Independent Counterweighting For Partial Body-Weight Support In Rehabilitation, Ashish Shinde

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents the design and testing of a body weight support system for gait training in a two-dimensional workspace. Extension of the system to a three-dimensional workspace is not within the scope of this thesis.

Gait dysfunctions are changes in normal walking patterns, often related to a disease or abnormality in different areas of the body. There are numerous body weight support (BWS) systems present in the market which are applied to rehabilitation scenarios in mobility recovery like in gait training. But most of these BWE systems are costly and generally are stationary devices. A major drawback of such …

Design Of A Test-Rig For Gerotor Pump, Weijin Qiu, Andrea Vacca, Matteo Pellegri

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gerotor pumps are a kind of fluid power machines widely used in the automotive field, especially for fuel injection as well as lubrication. To improve the performance of these units, virtual prototyping is necessary to decrease time and cost related to trial and error. Within this research a simulation model for Gerotor units has been developed with the aim of predicting accurately the performance of a generic unit. The model can accurately predict the system behavior regarding mechanical and volumetric losses by considering real machining tolerances and their interactions. Ultimately, this model should help to design new generations of Gerotor …

Ani-Bot: A Mixed-Reality Ready Modular Robotics System, Zhuangying Xu, Yuanzhi Cao

The Summer Undergraduate Research Fellowship (SURF) Symposium

DIY modular robotics has always had a strong appeal to makers and designers; being able to quickly design, build, and animate their own robots opens the possibility of bringing imaginations to life. However, current interfaces to control and program the DIY robot either lacks connection and consistency between the users and target (Graphical User Interface) or suffers from limited control capabilities due to the lack of versatility and functionality (Tangible User interface). We present Ani-Bot, a modular robotics system that allows users to construct Do-It-Yourself (DIY) robots and use mixed-reality approach to interact with them instantly. Ani-Bot enables novel user …

Development Of Portable Hyperspectral Imaging Device, Chenxi Li, Youngkee Jung, Iyll-Joon Doh, Euiwon Bae

The Summer Undergraduate Research Fellowship (SURF) Symposium

Most of the conventional hyperspectral imaging devices require sophisticated optical components, occupy a large footprint, and requires an initial capital investment for laboratories which mostly suits for laboratories benchtop system. The requirement of shipping the sample and waiting an extended period of time to get the results are the main downsides of this traditional approach. Capitalize in many specific field applications and diagnosis, portable devices provide both convenience and on-site results which are desirable for government agencies and food safety inspectors. This project was aimed to develop a low-cost, portable hyperspectral device for food safety applications. A smartphone was used …

Developing Methods Of Obtaining Quality Failure Information From Complex Systems, Oladapo Olalekan Bello

Graduate Theses and Dissertations

The complexity in most engineering systems is constantly growing due to ever-increasing technological advancements. This result in a corresponding need for methods that adequately account for the reliability of such systems based on failure information from components that make up these systems.

This dissertation presents an approach to validating qualitative function failure results from model abstraction details. The impact of the level of detail available to a system designer during conceptual stages of design is considered for failure space exploration in a complex system. Specifically, the study develops an efficient approach towards detailed function and behavior modeling required for complex …

Visualization And 3d Printing Of A 3d Solar Tracker Model Using Mayavi And Pov-Ray, Aditya Mehra

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

In this work, we have created a realistic model of a solar tracker using Mayavi: 3D scientific data visualization and plotting in Python, Enthought Canopy:a comprehensive Python analysis environment and Persistence of Vision Ray Tracer, or POV-Ray, a ray tracing program which generates photo-realistic images from a text-based scene description, a model of the solar tracker was also 3D printed.

Development Of The End-Effector Of A Cable-Driven Parallel Manipulator For Automated Crop Sensing, Iman Salafian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A four cable-driven parallel manipulator (4CDPM), consisting of sophisticated spectrometers and imagers, is under development for use in acquiring phenotypic and environmental data over an acre-sized maize field. This thesis presents the design, controls, and testing of two sub-systems in a 4CDPM: a Center of Mass Balance System (CMBS) and a Drop-Down System (DDS).

One of the factors that influences stability is the center of mass (COM) position of the end effector. An offset in COM can cause a pendulum effect or an undesired tilt angle. A center of mass balancing system is presented in this thesis to minimize the …

A Parametric Investigation And Optimization Of A Cylindrical Explosive Charge, Logan Ellsworth Beaver

Master's Theses (2009 -)

Explosive device design has a wide impact in the space, manufacturing, military, and mining industries. As a step toward computer assisted design of explosives, an optimization framework was developed using the Design Analysis Kit for Optimization and Terrascale Applications (Dakota). This software was coupled with the hydrocode CTH. This framework was applied to three exploding cylinder models, two in 1D and one in 2D. Gradient descent, dividing rectangles, and a genetic algorithm were each applied to the one-dimensional models. Parametric studies were performed as a basis for comparison with the optimization algorithms, as well as qualifying the 1D model's accuracy. …

A Study In The Use Of Elastic Materials In Expandable Containment Units, Andrew J. Eisenman, Joby Anthony Iii, David Satagaj

Montview Journal of Research & Scholarship

The rigidity of materials in conjunction with the aspect of elasticity has been a concern of modern technologies and construction in recent centuries because of the advantages that expandable storage would bring to the fields of containment units with respect to population growth and space exploration. The world population is currently growing at an exponential rate, and as our population grows, the more important it will become to have containment units that can both contain large volumes of material as well as minuscule amounts of material without wasting space. In order accomplish this, we will need a new type of …

Comparing Building Modeling Software To The Energy Record Of A Preexisting Structure, Nathan Lasley

Mahurin Honors College Capstone Experience/Thesis Projects

Buildings are complex systems - even "simple" residential structures. Many factors go into building energy consumption and the design to reduce it. Computer energy modeling allows the simultaneous consideration and balance of many of those variables. Computer models are only as good as the information provided however. Tools like blower door and duct blaster can be used to aid in verifying the model or to provide more information to build a better model. In order to verify of building computer energy simulation methods, the Western Kentucky University (WKU) Office of Sustainability located at 503 Regents Ave. in Bowling Green KY …

Additive Manufacturing For Post-Processing, Nathan D. Goodwin, Andrew Furmidge

Mechanical Engineering

Additive Manufacturing for Post Processing (AMPP) is a team comprised of two Cal Poly Mechanical Engineering students: Nathan Goodwin and Andrew Furmidge. The project is focused in the area of metal additive manufacturing (AM) machines, which are still a developing technology. Improvements have been made to the quality of the machines in the past years, but many limitations still exist. One of these is the inability to print parts that are larger than the build volume. In an effort to solve this problem, whole parts are divided into pieces that are printed individually. This team’s senior project is to create …

Bear Minimum: Ultralight Composite Bear Canister, Rama B. Adajian, Adam C. Eisenbarth

Mechanical Engineering

The ultralight backpacking community needs a strong, easy to use, safe bear canister that is lighter than current market products for trekking in the backcountry. A full design of the lid for the bear canister is to be completed. This includes the locking mechanism to ensure it is bear proof, the interface between the lid and the canister, and the structure of the lid so it passes the strength and weight specifications. The lid, along with the already designed canister body, is to be manufactured with formal documentation. The lid will initially be tested separately and then with the canister …

Development Of 3d Compression Molded Composite Primary Structure, Sean D. Tischler, Jacob H. Goldstein, Alea A. Perez

Mechanical Engineering

The work accomplished by the Black Gold team improved upon the carbon fiber compression molding research and information available on the Cal Poly San Luis Obispo campus. The team used the rear suspension rocker arm off a Ventana Alpino mountain bike as a design goal for this project. This research and body of work includes the methods used to design a compression molded part for complex part loading and shape. This extends to the process of choosing an appropriate layup process, in addition to benefits and drawbacks of the use of chopped fibers in compression molding. The research includes the …

Leading Edge Boundary Layer Suction Device For The Cal Poly Rolling Road Wind Tunnel, Daniel C. Glover, Liam M. Madden, Robert J. Cabri

Mechanical Engineering

Over the course of three quarters from Fall of 2016 to Spring of 2017, our team designed and built a boundary layer suction device. The boundary layer suction device has three main functions: a scoop that redirects most of the boundary layer air out of the wind tunnel, fans that suck the remaining boundary layer air through a porous plate and ducting and out of the wind tunnel, and a transition bridge that transitions the remaining air smoothly onto the rolling road. The wind tunnel is owned by Cal Poly and the rolling road is a new addition to it. …

Pedal-Powered Drivetrain System, Geremy J. Patterson, Callaghan Fenerty, Bradley Welch

Mechanical Engineering

No abstract provided.

An Experimental Study On Drag Reduction Of Aftermarket Additions On An Suv, Christiana L. Katsoulos

Senior Honors Projects, 2010-2019

Over recent years, the awareness of climate change has become more prevalent worldwide and one major contributor to global warming has been the use of transportation. Vehicles contribute to global warming by releasing petroleum based emissions such as significant amounts of carbon dioxide and numerous other harmful environmental pollutants. SUVs contribute to the emissions problem more so than sedans, since they have lower gas mileage and need more gasoline regularly. The main functionality of sport utility vehicles, or SUVs, includes hauling or off-roading and fuel efficiency is not always the focus in the design process. However, aerodynamic enhancements could improve …

Automation In Entertainment: Concept, Design, And Application, Ryan Thally

Undergraduate Honors Theses

The focus of this thesis is to explore the automation technology used in the modern entertainment industry. Upon completion of my thesis, I will deliver a working prototype of the chosen technology and present its capabilities in a choreographed show.

The Intersection Of Manufacturing Technologies And School Music Programs, Leslie Prunier

University Scholar Projects

The objective of this project is to design and manufacture a musical instrument, a marching baritone horn, out of plastic. It is constructed out of both PVC pipe and 3D-printed components. Utilizing this project’s documentation, a high school student could use a 3D printer and other basic tools to make their own musical instrument for a fraction of the cost of purchasing one. This documentation will produce a horn tuned in the key of B flat with one functioning valve, and suggestions for future work to make the other two valves functional as well.

Chip-Package Interfacial Stress Analysis And Reliability Implications For Flip-Chip Power Devices, Jonathan Gh Treco

Mechanical Engineering Undergraduate Honors Theses

The solder in flip-chip assemblies experience high stress and strain because of thermal mismatch induced deformation. These deformations occur because of the differences of coefficient of thermal expansion between flip-chip assembly materials. The similarly in stress profiles between thermal induced and shear induced stress in solder joints enable the use of die shear testing as a representative technique for relating the max stress the flip-chip can withstand to cyclic thermal fatigue failures. In this work, two electronic device sample preparation types are evaluated: One set of samples are soldered together and other set of samples use epoxy as an adhesive. …