Computer-Aided Engineering and Design Commons^™

Elevate Hardcase, Caleb J. Bailey, Colby M. Cordoba, Marissa Mccleod, Shaan Sandhu

Mechanical Engineering

The Elevate Hardcase project developed a portable mechanical elevation system that allows users to access rugged hard cases at a comfortable working height without needing a separate table or placing the case on uneven ground. The design focuses on improving ergonomics, portability, stability, and quick setup for users in field environments such as photography, hunting, and maintenance. Through customer research, concept development, prototyping, analysis, and testing, the final system was designed to support a loaded hard case, provide height adjustability, remain stable on uneven terrain, and be deployed by a single user in under five minutes. The final prototype demonstrates …

Mars Rover Wheels And Drive, Presley S. Sacavitch, Ryan W. Trevena, Dylan A. Mack, Daniel Hudak

Mechanical Engineering

Cal Poly’s Poly1Rover team, advised by Professor Rich Murray, aims to deploy four student-designed mini-Mars rovers, each equipped with a sample-tube retrieval claw, before 2030. However, the wheels of Poly1Rover’s current 6th generation rover are not ready for deployment to Mars, as they do not utilize space-grade materials, are not optimized for manufacturability, and lack sufficient spoke compliance to absorb landing and high-impact loads. This project will be developed by a team of Mechanical Engineering students at California Polytechnic State University, San Luis Obispo (Cal Poly): Daniel Hudak, Dylan Mack, Presley Sacavitch, and Ryan Trevena. Next Intent is providing funding …

Formula Sae Planetary Gearbox Characterization Dynamometer, Trevor Marco Toma, Thomas Welden Pierce, Ethan Liu

Mechanical Engineering

This report outlines a custom hub motor dynamometer requested by the Cal Poly Racing FSAE team. The need for this testing platform is to characterize an existing Formula SAE planetary gearbox for a proposed 4WD powertrain. Hub motors, compact electric machines integrated directly into each outboard wheel, offer significant advantages in efficiency, traction, and chassis packaging compared to conventional RWD drivetrains. By mapping torque capacity, efficiency, lubrication method effectiveness, and fatigue life, the team can validate gearbox design and performance.

This senior project group designed and built a dynamometer according to these specifications which will allow for successful testing to …

Peltier-Based Hydration Accumulation Terminal (P.H.A.T.), Jenner Mucher, Ethan Pace, Renee Robolledo, Sabrina Luo, Taehoon Lee, Tarsem Pal

Mechanical Engineering

The objective of this project is to design an innovative potable water dispenser capable of safely delivering hot, ambient, and chilled water on demand for human lander missions. The system will support astronauts’ hydration and food rehydration needs while minimizing mass, power, maintenance, and contamination risks in microgravity and partial-gravity environments. Current spacecraft dispensers, such as the International Space Station (ISS) system, provide only heated water and have limited temperature control, cleaning accessibility, and microbial resilience. Building on NASA heritage designs and lessons learned from the ISS Potable Water Dispenser, this project advances a lighter, simpler, and more energy-efficient concept …

Smart Sleeve, Evan Abalos, Bright Jung, Owen Bowling, Wyatt Eberhart

Mechanical Engineering

Quantifying human arm muscle activity is essential for understanding human movements and helping individuals who suffer from motor or neurological impairments such as stroke or traumatic brain injuries. Today, these individuals, as well as clinicians, researchers, and athletes, face many challenges when using the traditional surface electromyography (sEMG) systems to monitor muscle activities, including complex setup, restricted mobility, discomfort, inconsistent placement of electrodes, and lack of accuracy. Therefore, a comfortable EMG sleeve device that accurately measures arm movement without interfering with daily tasks is needed, which the team will be designing, manufacturing, and testing as their senior project. In addition, …

Process Improvement For Thermal Barrier Coating Masking Applications, Katherine Meezan, Aiden Senn, Saksham Giri, Katelyn Perez

Mechanical Engineering

Solar Turbines, a gas turbine manufacturer, needs a more efficient method to prevent the application of a thermal barrier coating (TBC) to select areas of their combustion liners during manufacturing. Currently, the process is labor, material, and time intensive: reusable masking tools should increase the efficiency of the TBC process.

This project is sponsored in full by Solar Turbines, and is under the guidance and administration of three Solar Turbines engineers: Chris Noone, Rick Rogers, and Carson Roff. The project is mentored by Cal Poly senior design Coach, Rick Lasko. This project will be completed by a team of four …

Cal Poly Fluid Powered Vehicle Challenge 2025/2026, Ethan Malachi Nejame Zeiset, Christian Anthony Cuamani, Daniel Chacon-Bizarro, Marcus Minera, Bradley Hansell

Mechanical Engineering

In this Final Design Report, the Cal Poly Fluid Power Vehicle Challenge Contending Team competed in Sun Hydraulics’ 2026 Fluid Powered Vehicle Challenge. The objective of the competition is to expose college students to the fluid power sector, the “hidden giant” of the engineering industry. Specifically, student teams are tasked with the development of a human-powered, fluid-driven vehicle for use in various competitive settings. The team prioritized the optimization of an existing prototype for simplicity, ease of maintenance, and reliability during the competition. The existing prototype exhibited issues related to the main frame’s deflection under load, a lack of gear …

Mars Mini Rover Sample Retrieval Robotic Claw, Cami Chambers, Ani Lachikian, Alexa Ramirez, Alex Power

Mechanical Engineering

This project involves several key stakeholders, including the Poly1 Rover Club, Professor Rich Murray, and NASA’s Jet Propulsion Laboratory (JPL). The primary objective is to develop an improved robotic claw capable of retrieving sample tubes left by the Perseverance Rover on the Martian surface. In tackling this challenge, the design must account for the harsh Mars climate while integrating cameras and electrical components, durable structure, and a rotational component to the Mini-Rover claw without incorporating an additional motor, sample storage unit, structural aspects or unnecessary weight. The current Mini-Rover consists of a four-degree-of-freedom robotic arm with joints often referred to …

Sensory, Light, And Sound Box, Galilea Andrea Portillo, Hannah Elizabeth Henderson, Marcus Kiyoshi Kanenaga

Mechanical Engineering

The Sensory, Light, and Sound Box senior project outlined an adaptable, mobile sensory environment designed to improve cognitive and visual processing skills for students with Cerebral Visual Impairment (CVI) at the Oceano Education Center. Currently, the market lacks accessible solutions tailored to these non-verbal, low-mobility students, making traditional classrooms overwhelming. This project outlines the modification of an existing static layout into a functional, three-sided wooden over-bed frame that accommodates a standard hospital bed. Our team manufactured a structurally stable verification prototype under a $500 budget, integrating slow-closing outward-hinged walls for safety, dual Bluetooth speakers, and a synchronized LED projector that …

Portable Ice Cube Maker, Ayden Ziegler, Emiliano Hansen, Wyatt Engdahl, Dane Hansen

Mechanical Engineering

This Final Design Report outlines the senior design project undertaken by a team of mechanical engineering students at California Polytechnic State University, San Luis Obispo, for the development of a portable backpacking ice cube maker. The project aims to design, build, and test a lightweight, compact device that produces ice cubes for backpackers in remote outdoor environments. The goal is to create a functional prototype that is durable, user-friendly, and suitable for backcountry use. This document details background research, project objectives, and project plan, and current design status.

Fsae Bespoke Brake Calipers For Hub Motor Architecture, Connor William Vaughan, Liam Upton Walsh, Bradley Brian Kern

Mechanical Engineering

Brakes are the most critical safety system on any performance vehicle, and as Cal Poly Racing transitions their Formula SAE car from a single rear motor to a four-in-wheel motor setup with regenerative braking, the team identified an opportunity to develop a bespoke brake caliper tailored to their specific needs. This document outlines the research, design, manufacturing, and validation of custom front brake calipers designed to improve upon commercial motorcycle calipers in key areas such as serviceability, mounting rigidity, thermal behavior, mass, and hub motor integration. The resulting design is a two-piece, four-piston, radially-mounted aluminum caliper featuring titanium pistons, toolless …

Cvj Torque Loss Dynamometer, Malaika Sriram, Coleman Brown, Zachary Norris, Logan Mast, Chris Mattis

Mechanical Engineering

This report details the design and results of a dynamometer testing rig built to measure torque losses in constant velocity joints (CVJs) for Cal Poly Racing's Baja SAE team. The rig spins a flywheel connected to articulable CVJs up to 800 RPM using a motor, then decouples it and measures the spin-down rate from 800 to 100 RPM to calculate angular acceleration and torque loss. The data collected from this dyno will be used to inform freewheel packaging for future Baja car development.

Aerospace Fastener Installation Tool, Anthony I. Berghout, Matthew K. Eggers, Liam Dunsmore, Jose Pardo

Mechanical Engineering

Contamination, particularly in aerospace manufacturing environments, is a significant concern, especially with fastener designs that incorporate torque-rated breakaway pieces for easier installation. These breakaway pieces are also known as pintails. Howmet has tooling that can collect loose pintails during installation, but they have small capacities and are not ergonomic for aerospace technicians. Their current need is for a light and ergonomic tool capable of installing a wide variety of Ergo-Tech® fasteners while having a large capacity to collect pintails and improve aerospace manufacturing methods. For this Critical Design Stage, we have finalized a design that allows Pintails to pass through …

Aluminum Boat Rotation Fixture, Kevin W. Heiskell, Nathaniel M. Conway, James S. Knowles, Austin J. Kehl

Mechanical Engineering

Aluminum fishing boats are widely used for various water-based activities, including fishing, transportation, and recreation. Their lightweight construction makes them ideal for maneuverability, particularly in regions like Australia. However, the manufacturing process presents challenges, specifically the need to weld both the interior and exterior seams of the hull. As the boat’s weight increases during assembly, flipping it becomes difficult and potentially hazardous. Traditional methods such as cranes or forklifts are inefficient and pose safety risks. To address this, our team developed a rotating fixture that secures the boat at two connection points, one at the bow and one at the …

Llnl Raft Flash Pole Redesign, Jack Stangel, Evan Wolfson, Jake Borden, Alexander Meeter

Mechanical Engineering

During research exercises in the ocean, Lawrence Livermore deploys a fleet of rafts outfitted with flash modules affixed to tall poles (in tandem called flash poles) that flash while a photo is taken to act as datums for data collection. The current flash pole design that the LIDSS (Lawrence Livermore Independent Diagnostic Scoring System) team uses is too short to be visible in high seas, not mechanically suited to be made taller, too susceptible to the elements and blunt impact and too difficult to service. We aim to solve these issues.

Micro Mobile Home R3, Roha Y. Ali, Yuka M. Iwashita, Luke C. Douglas, Joshua Q. Le

Mechanical Engineering

Homelessness is an ever-growing issue all around the world. In 2023, over 250,000 or ~40% of all people experiencing homelessness did not have access to shelter spaces in the U.S. [1]. All people have the right to a place where they are safe from violence, crime, and the constant fear that they will be forced out.

Both homeless people and outdoor enthusiasts need a new way to keep themselves and their belongings safe when living outdoors, since existing products do not offer adequate security, portability, or versatility.

Large Backflow Check Valve Life Cycle Test Stand, Colin Bentley, Christopher Carloni, Ethan Gray, Luke Romanini

Mechanical Engineering

Backflow preventers are plumbing devices containing internal check valves used to prevent cross-contamination between downstream contaminants and potable water supply. Zurn Wilkins needs a life cycle test stand to mechanically force open check valves submerged in contaminated water and verify check performance. The stand needs to be modular to work with a range of check types and sizes.

Zurn Wilkins is the primary stakeholder for this project. Secondary stakeholders include commercial and residential building owners, contractors, and water utility companies, who rely on their products for safe and efficient water management. The team for this project consists of four Cal …

3d Printed Fixed Wing Aircraft Competition, Sidney E. Long, Mitchell Heise, Jack Bride, Daniel Salinas

Mechanical Engineering

Cal State LA and Arlington University, Texas are hosting the same 3D printed, fixed wing aircraft competition for 2025. Cal Poly requires a competitive plane that can adhere to each rule and be piloted remotely to achieve the longest time in the air. The plane must utilize solely 3D printing technology for the wings, body, and all other structures. The only off-the-shelf components can be the motor and electronics, as well as mechanical devices such as hinges.

Lidss Raft Battery Pack Integration, Jack Maxwell, Vincent Stevens, Matthew Hoodmaker, Colin Flanders

Mechanical Engineering

Lawrence Livermore National Laboratory is a critical member of the United States Department of Defense. Their Independent Diagnostics Scoring System (LIDSS) uses rafts that operate in the ocean to collect missile test data. Several times a year, the United States will test their Inter-Continental Ballistic Missiles by launching them into the ocean near the Marshall Islands. This is where the LIDSS rafts collect their test data. Our project was centered around re-designing the battery pack used by the rafts. The current battery pack design experiences water ingress problems and is difficult to access. Our re-designed battery pack is waterproof to …

Baja Sae Brakes, Carson Moore, Jaedyn Michael Imhoff, Will Duncan, Matthew Shaffer

Mechanical Engineering

Historically, the Cal Poly Racing Baja SAE has produced a braking system that has proven unreliable and barely passes competition rules and inspections, leading to ill performing and unsafe brakes. The goal of this project is to produce a system and documentation that meets the requirements provided by Cal Poly Racing Baja SAE. The final design includes a transient braking model of the vehicle to set system requirements, universal custom front and rear calipers modified from “Cal Poly BSAE Custom Brake Caliper Senior Project”, and a revamped hydraulic harness. Leaning on the team’s previous work and modifying the custom calipers …

Emg-Based Intraoperative Neuromonitoring Using Advanced Machine Learning Approaches, Abdalla Nabil Elsharkawy, Nourhan Zayed

Mechanical Engineering

Intraoperative neuromonitoring (IONM) plays a critical role in minimizing nerve damage during surgeries by providing real-time feedback on neural integrity. This study evaluated models associated with deep learning and machine learning models for electromyography classification of signal during intraoperative neuromonitoring (IONM). The CNNLSTM model achieved the highest accuracy (85.2%), outperforming traditional models like KNN (53%), RF (62%), and CNN (76%). This demonstrates the degree to which the CNN-LSTM model can gain insight into temporal and spatial dependencies throughout the EMG signals, which makes it optimal for real-time classification in IONM applications. This implies that deep learning techniques can improve surgical …

Development Of Planetary Drive System For Formula Sae Electric Race Car, Brian Wong, Bradley Maruoka, Joshua Charles Fine, Madison Kai

Mechanical Engineering

Hub motors are compact electric motors mounted directly on each outboard wheel hub. Utilized in Formula SAE and Formula Student vehicles, this configuration offers several advantages over traditional drivetrains, including packaging optimization within the chassis, vehicle traction, and improved efficiency. Although hub motors are not yet common in 4WD vehicles, they are being explored for use in EVs and may become more common in the future. Every year, Cal Poly Racing FSAE designs and builds a formula-style race car. To improve drivetrain performance, the team is investigating the achievability of a hub motor 4WD drivetrain, requiring extensive research, development, and …

Expandable And Retractable Wheel Design, Ethan Fortenberry, Emily Cottrell, Keegan Martin, Benjamin Mcconnell

Mechanical Engineering

Our sponsor, Jeremy Goren, wants to see his patented expandable wheel design come to life. He requires a functional final product actuated by linear actuators and with a continuous, circular outer shell. The overall design can be broken up into 2 parts: the inner hub and outer shell. The wheel's shell will consist of a 12-piece outer shell that guides the 6 inner shell pieces. The outer shell pieces will be connected via a UBracket. The hub will consist of 3 identical parts that will hold 2 linear actuators each. The pieces will be bolted together to create 1 singular …

The Waterbug: Adaptive Paddle Board Frame, Remy James Elio Lacchia, Katie Kellum, Madeline Evenson, Shelbi Sullaway

Mechanical Engineering

People with disabilities, particularly wheelchair users, face limitations in participating in outdoor activities like paddleboarding. Central Cal Adaptive, a nonprofit organization, aims to bridge this gap by offering adapted paddleboarding experiences. However, their current paddleboard presents challenges such as portability, range of motion, stability, and safety. Our team, comprising Madeline Evenson, Remy Lacchia, Katie Kellum, and Shelbi Sullaway, has collaborated with Central Cal Adaptive to refine the existing paddleboard design. The team’s goal is to enhance the paddleboard's functionality to better cater to wheelchair users' needs, ensuring lightweight, portable, and safe features for an improved outdoor experience.

Our paddleboard concept …

Piston Crown Design, Kurt L. Lippmann, Liam T. Janssen, Alex Rangel, Larry J. Davis

Mechanical Engineering

This project investigates the effects of dimpling a piston crown, and its impact on engine combustion dynamics. Through computational methods, the effects of piston crown dimpling on flow characteristics were evaluated. Theoretical results were verified with experimental methods. Experimental methods included characterization of exhaust gas content, engine horsepower and torque, and exhaust opacity.

Robot Rodeo, Daniel Rickers, Tyler Vaughn, Vinayak Sharath, Berent Baysal, Promit Das Gupta

Mechanical Engineering

This document outlines the Final Design Review (FDR) for an autonomous robot developed in response to the Naval Surface Warfare Center (NSWC) Ship Maintenance Robot Rodeo Challenge. Through extensive analysis, we selected a design concept, built a verification prototype, and tested the prototype in the NSWC Robot Rodeo Competition. The design overview portion of this report will present the details of our design while explaining how it will function. Next, is our implementation section, which provides evidence about our procurement, manufacturing, and assembly of our product. Our design verification follows and explains the tests that we conducted on the robot …

Scitechatorium Exhibit, Adam Khan, Cole Busch, Logan Femling, Alan Onuma

Mechanical Engineering

This document outlines the final stages of development and analysis of our interactive children’s exhibit for the Bellevue-Santa Fe Charter School’s SciTechatorium. We will showcase the final form of our ball and track display, giving a detailed look at each component and subsystem.

To describe how our final prototype will be built we have included a detailed manufacturing summary for our design. Our models have been designed with manufacturability in mind, and we have outlined which processes were used to produce all our parts.

There are also detailed descriptions of testing that were conducted to verify the performance of the …

Supermileage Competition: Vehicle Chassis, Enrico Miguel Sangalang, Walter Oppelt, Adam Ponce, Vincent Corella

Mechanical Engineering

The Supermileage Urban Concept Vehicle Chassis Project was proposed by the Cal Poly Supermileage club. The goal of this project is to deliver a fully assembled vehicle chassis by the end of the 2023-2024 school year to be used by the club in the 2025 Shell Eco-Marathon competition. The competition requires a four-wheeled vehicle to comply with various requirements outlined in the Shell Eco-Marathon rulebook, such as dimensions and some safety requirements. The team selected a backbone-style chassis as the design direction. This design consists of a main structural beam that supports all other chassis and vehicle components. This main …

3d-Printed Remote Controlled Aircraft, Sebastian Bessoudo, Jose Ramirez, Manny Ruiz, Andrew Edwards

Mechanical Engineering

The Senior Project for the 3D Printed Aircraft presents a compelling challenge to the team: design and fabricate an aircraft for the Cal State LA 3D-Printed Fixed-Wing Aircraft Competition, comprising three distinct events: Flight, Design, and Simulation. The objective of the flight competition is to achieve the longest flight duration, while the design event emphasizes innovation and originality. In the Simulation contest, our aircraft's CAD model undergoes Computational Fluid Dynamics analysis to assess its aerodynamic performance. These competitions are slated for May 2024.

While building the aircraft has its limitations due to the source of our construction being only 3D …

Miniature Train Engine, Jason Patrick Lacson Del Castillo, Renato Andrew Dilauro, Sophia Theresa Tiu, Robert John Pallares Iii

Mechanical Engineering

This report details the redesign of the Mini Train Prop for the SLO Civic Ballet’s The Nutcracker, aiming to create a lighter, more user-friendly, and easily maneuverable train. The Final Design Review (FDR) includes the design process, manufacturing plan, and justifications for decisions made. Key improvements are reducing the train's weight, automating the fake wheels, and enhancing maneuverability with a neutral pin and lever system. In this report we detail the significant changes since the Critical Design Review (CDR). The implementation covers procurement, manufacturing, and assembly, while design verification ensures compliance with cost, weight, turn radius, and structural integrity specifications. …