Applied Mechanics Commons^™

Hitch Cart “Landing Gear”, Rebekah White, Jose Raygoza, Randy Hernandez, Brandon Leon

Mechanical Engineering

This report aims to allow our sponsor, to review our design process of the Hitch Cart Landing Gear Prototype. In the design overview section of this report, we discuss the primary design modifications we made to the wheel mechanism of the existing hitch cart prototype, including the addition of the ACME screws and the folding brackets. This allows our sponsor to see the intended improvements made to the past prototype and understand the primary goal of our project. Then, in the implementation section, we cover the entire manufacturing process to allow our sponsor to understand what manufacturing steps must be …

Headlamp/Bike Light Damping System, Ethan Reece Clark, Alec Stonehouse, Omeed Ostry, Mitchel Anderson

Mechanical Engineering

The task for this project is to design a headlamp and/or bike light that absorbs the impact shocks from the user’s actions. The user that the system is being designed for may be riding a bike or running on a trail in the evening or early in the morning where the light needs to be stabilized and their path must be illuminated. This report presents the final design chosen after months of prototyping and design iteration. It encompasses the system design, design verification through testing, implementation, future recommendations, and lessons learned throughout the process. The chosen design utilizes a fully …

Disc Golf Throwing Robot, Nevada S. Schultz, Sydney M. Lewis, Erick Edmundo Daza, Rachel Alysse Greenberg, Peter M. Kean

Mechanical Engineering

Disc golf companies need better methods to test disc flight. The scope of this project is to create a disc throwing robot that can throw a disc golf driver 450-500 feet, with control over the speed, spin, and release angle. Research shows that multiple disc-throwing products exist; however, none meet the full requirements of this project. The Cal Poly senior project design team created a proof-of-concept machine. This prototype started as a two-wheel mechanism. Eventually, a third wheel was added, allowing for complete control over disc spin. The three-wheel prototype reached 62 mph when perfectly calibrated. The prototype is accurate, …

Programmable Vibration Table Retrofit With Eagle Medical, Jonathan Ilagan, Madhav Asok, Max Lewter

Biomedical Engineering

This project aimed to repair and upgrade a vibration table used for package testing for the sponsor, Eagle Medical - a medical packaging and sterilization company based in Paso Robles, California. The current vibration table is not programmable and lacks circuit diagrams, making it difficult to repair. In addition, it is not functional due to internal circuitry issues and power requirements. To address these issues, the team will implement several upgrades to improve the product and allow for better random cyclic vibration testing. A full assessment of the existing vibration table will be conducted to ensure the viability of these …

Novelty Ice Cream Assembly Prototype, Mason Sylvester, Logan Williamson, Alvaro Martinez, Adin Gilman-Cohen

Mechanical Engineering

Cool Beans USA is a novelty ice cream startup company founded by Keith Zachow. In the winter of 2022, our team began working with Mr. Zachow to develop a machine to automate parts of the production process for his product. This product consists of two hemispherical ice-cream cone shell halves filled with soft serve ice cream and pressed together. The assembled pods are around the size and shape of a small walnut and are intended to be sold in stores as a frozen finger food. At the time of project inception, this product was in its early stages and was …

Novel Hitch Cargo Cart, Cesilio Sanchez Ramirez, Lance Haidet, Richard Lontoc, Tyler Selinka

Mechanical Engineering

This document presents the engineering design process used to develop, manufacture, and test a new and improved iteration of a hitch cart prototype. This process was performed by a team of four mechanical engineering seniors as part of California Polytechnic State University, San Luis Obispo’s senior design pathway. The goal of this project was to develop a sturdy and reliable iteration of our sponsor’s hitch cart prototype, that integrated the functionality of a vehicle hitch cargo platform and that of a height adjustable cargo cart into a single streamlined and easy to use product. This design could be used by …

Interactive Lego Girl Scout Arm, Chris Suzuki, Emi Okuyama, Bryson Shores, Karina Sandoval

Mechanical Engineering

This Senior Project Report document outlines the senior design project for Girl Scouts of California’s Central Coast (GSCCC) led by a team of four Mechanical Engineering students at California Polytechnic State University, San Luis Obispo. The project encompasses the researching, designing, prototyping, and testing of a LEGO robotic arm for the Girl Scouts to learn more about STEM (Science, Technology, Engineering, and Mathematics) and provide support to each Girl Scouts cookie sales in their stores. Their goal was to build a LEGO robotic arm that will interact with customers at the Girl Scout stores and promote the girl scouts' interest …

Design Of A Proprioceptive Actuator Utilizing A Cycloidal Gearbox, Craig John Kimball

Master's Theses

Legged robotics creates the demand for high torque compact actuators able to develop high instantaneous torque. Proprioceptive actuator design theory is a design theory that removes the need for a torque feedback device and relies on the stiffness in the leg for absorbing the high Ground Impact Forces created by walking locomotion. It utilizes a high torque density motor paired with a gearbox with a high gear ratio for torque multiplication. Previously work has been done to design a proprioceptive actuator design that utilizes a planetary gearbox to create a modular low-cost actuator for legged robotics. The purpose of this …

Adjustable Head Tube Angle Headset, Glenn Petersen, Ben Harper, Josh Martin, Dylan Prins

Mechanical Engineering

This final design review report describes the design, manufacture, and test process of a bicycle headset capable of quickly and easily adjusting the effective head tube angle. The evolution of mountain bike geometry has forced bike designers to compromise between climbing and descending performance when choosing a head tube angle. A headset capable of quickly adjusting the effective head tube angle would allow riders to optimize their bike’s geometry for different stages of riding. This report details the research, idea generation, concept development and selection, design, manufacturing, and testing of our adjustable head tube angle headset.

Tensile Testing Environmental Chamber – Structural, Michael Ingel, Erik Soldenwagner, Austin Marshall, Lauren Schirle

Mechanical Engineering

Environmental chambers for tensile testing machines are used to study how a multitude of materials behave in extreme temperatures. These chambers provide the necessary information to innovate cutting edge technology for materials in fields such as aerospace. These chambers are often heavy and expensive requiring a significant amount of time and money just in the installation process alone. This report will serve to outline and define the design and fabrication of an environmental chamber, conducted by a team of four senior mechanical engineering students at California Polytechnic State University, San Luis Obispo. The goals of the project include a low-weight …

Cnc Feed Drive Control, Ryan J. Funchess, Caleb P. O'Gorman, Nick J. Desimone, Juan M. Majano, Samuel K. Wong

Mechanical Engineering

This document serves as the Final Design Report (FDR) for a senior project developed by our team: four senior Mechanical Engineering students and one computer engineering student at California Polytechnic State University, San Luis Obispo (Cal Poly). While the project was completed for, and sponsored by, Professor Simon Xing of Cal Poly, the remainder of the university’s controls professors will be indirectly benefited from this project. Our goal was to design and implement a functional CNC Feed Drive to be used for educational demonstrations and data collection. This document discusses our early product research and benchmark goals, which established constraints …

F34 Beekeeper Assist, Kyle Ladtkow, Javier Guerra, Jose Velazquez, Ryan Heryford

Mechanical Engineering

Alejandro Jauregui is a veteran who now works as a commercial beekeeper. He lost both of his legs during his service. While his current prostheses allow him to fully complete his work, he has found that inspection of the bee boxes causes him severe hip and back pain. Bee box inspection is a critical task for beekeeping, especially since he maintains about 200 hives every day. Our senior project team was tasked with designing and building a device that would help him move the top bee box out of the way to allow for inspection. We performed preliminary research into …

Configurable Seat Track Latching Mechanism, Emily Sun, Kai Quizon, Rick Hall, Daniel Turn, Nicholas Holman, Alexander Kuznik, Jacob Winkler, Audrey Trejo, Phoebe Zeiss, Steven Kam

Mechanical Engineering

The reconfigurable seating system is a flexible seating solution for transit vehicles that allows operators to change the configuration of the floor plan in a timely manner in order to accommodate change in needs. This project consists of three senior project teams each working on a component of the design: system, track & latch, and articulation. Descriptions of the responsibilities of each team will be discussed below.

Composite Pegboard, Asa J. Cusick, Luis Corrales, Joelle Hylton, Wyatt Pauley

Mechanical Engineering

Many of those with mobility limitations who are told they will need a wheelchair for the rest of their lives can actually begin to stand and walk again given the proper tools and support. The current design for a wheelchair seeking to support this process is overly complex, heavy, and exhibits some features that could potentially pose a serious health hazard to those using it. The scope of this project is to aid in the design of an adaptable composite wheelchair frame that can be both lightweight and strong, while still allowing for physical diversity of potential users. Through research …

Enduro Campers, Ryan J. Shomsky, Alexander W. Horst, Kevin S. Pickering, Jackson L. Aplanalp, Luke Arana, Will Firestone

Mechanical Engineering

The Enduro Campers senior project team (Formerly known as Lobo Campers senior project team) was recruited by Mr. Leif Stein to assist in the design, manufacturing, and testing of the materials and components of his company’s expedition box camper. The two main focuses of the project, divided into two sub-teams, were on the testing and manufacturing process of the materials used in the camper, and on the design and analysis of the camper’s access door, step box, and other subsystems.

The focus of the materials analysis and manufacturing team was based around the design parameter to use composite sandwich panels …

Half-Barrel Planter Mover, Mihir Shah, Natalie Lewis, Mason James Hughes

Mechanical Engineering

A device for transporting heavy barrel planters is needed. Barrel planters are wooden wine barrels that have been cut in half along the circumference. They are used to store and grow a variety of plants. As such, they can contain more than 300 pounds of soil. The products currently on the market are not designed for such heavy planters, are cost prohibitive, and do not take advantage of the tapered design of a wine barrel half. A solution is needed that is durable, easy to use, and low cost. This final design report will show the steps used to find …

Dual Motor Drive System For Formula Sae Electric Race Car, Bryan D. Neill, Jackson T. Mcfaul, Cole T. Andrews, Isaiah D. Penzell

Mechanical Engineering

This paper serves as the Final Design Report (FDR) for the senior project developed by our team. This FDR builds on our CDR, in which the main deliverable was the detailed design of a planetary gearbox delivering a 5:1 reduction to be mated to an Emrax 188 motor. This planetary gearbox would allow for the possibility of implementing a dual-motor torque-vectoring rear-wheel-drive system in Cal Poly Racing’s electric FSAE car, which has demonstrated in simulation to yield significant performance gain over the current single motor/mechanical LSD system. As this project’s scope is purely mechanical, the intent is for the Cal …

Final Design Review Report: The Underdogs, Parker Johnson, Jack Montgomery, Katherine Thomas

Mechanical Engineering

Aspen is a three-legged dog with mobility issues from Berkeley, California. She was hit by a car and her rear left leg was amputated at the hip. Robin Swanson, Aspen's owner, and her friend, Audrey Beil, are the sponsors for this project. Jack Montgomery, Katherine Thomas, and Parker Johnson, “The Underdogs”, are tasked with helping Aspen regain some of her mobility and the ability to go on walks. Research was done into the problem by talking with the sponsors and looking into existing products, designs, and patents. This document, the Final Design Review Report, outlines the background information, problem specification, …

2 Degree Of Freedom Robotic Leg, Oded Tzori, Henry Terrell, Adan Martinez

Mechanical Engineering

Professor Xing, an assistant professor at Cal Poly, proposed the 2 DOF Robotic Leg project for this quarter’s senior project class. The project is to build a robotic leg attached at the hip to a stand, which will be used as a teaching tool and eventually help develop Cal Poly’s very own robotic quadruped. Since this project has multiple uses after its completion, there are multiple customers that it must perform well for: the Cal Poly Mechanical Engineering (ME) Department, the ME Lab instructors, and the students. The Scope of Work (Sections 2 & 3) is composed of 2 main …

Spring Loaded Camming Device, Jared S. Christner, Kaitlin O. Deherrera, Ryan W. Edwards, John S. Hickey

Mechanical Engineering

Spring loaded camming devices or “cams” are used in traditional rock climbing as a means of active fall protection. Climbers place cams in cracks and fissures in the rock wall. The cam’s lobes press against the walls, locking it in place, anchoring the climber in case of a fall. Currently, there is a lack of large cams on the market. Only two small companies produce cams that are usable in cracks 6.5 inches wide and larger, however their designs are either too heavy and/or lack features to be comfortable. We are a group of mechanical engineering students at Cal Poly …

Automated Drone Calibration System, Jackie Kelly Jong-Mee Paik, Zach Nathan Richter, Tyler Wilson Van Den Berg, Ryan Alexander Zhan, Matthew Ward Carlson

Mechanical Engineering

The final design review of the Inspired Flight Calibration Team senior project will detail the process used to complete a verification prototype of a drone calibration device and discuss lessons learned and suggestions for improving this device. Going from brainstorming and conceptual prototyping all the way through verification prototyping and testing, we were able to design a gyroscopic device that met Inspired Flight’s needs for the flight sensor calibration of their drones. The mechanical design involved comprehensive CAD models and hands-on manufacturing. The mechatronics side of the project worked heavily with electrical wiring and writing custom software to communicate and …

Safran Seat Attachment System, Craig John Kimball, Tyler Bragg, Lynette Cox

Mechanical Engineering

This final design review (FDR) document outlines the senior design project being carried out by a team of mechanical engineering undergraduate students attending California Polytechnic State University, San Luis Obispo for Safran Seats in Santa Maria, CA. The project originally was to design, build, and test a universal attachment to secure a widebody business class seat to seven aircraft models with different seat track geometry. The goal was to design, document, and create a finished product that fits design, weight, and manufacturing requirements, as well as passes static 9G FWD testing. Structural analysis, manufacturing analysis, FEA, and CAD assemblies will …

Cal Poly Supermileage Dynamometer, Jacob Randall, Nate Deffenbaugh, Kyle Milgram

Mechanical Engineering

Our senior project involves designing a chassis dynamometer capable of simulating variable loads for the Cal Poly Supermileage Vehicle (SMV) team. The chassis dynamometer we are developing uses an alternator to develop additional resistance that the vehicle will have to overcome while testing. To implement a control system for the variable load, we use an Arduino Nano paired with multiple sensors and drivers. This control system allows the user to select different levels of resistance that correlate with different road grades. We designed a custom Printed Circuit Board (PCB) that will contain all the electrical components needed for the control …

Baja Sae Ecvt Mechanical Design, Tyler Lee Connel, Will Daniel Antes, Matt Stephen Balboni, Benjamin James Colard, Julian Edward Finburgh

Mechanical Engineering

This objective of this project was to design, manufacture, and test the mechanical systems of an electronically-controlled continuously variable transmission (eCVT) for the Cal Poly Baja SAE vehicle.

Fluid Power Vehicle Challenge - The Incompressibles - Final Design Report, Nicholas Gholdoian, Russell Posin, David Vitt, Alex Knickerbocker, Kyle Franck, Julian Rodkiewicz

Mechanical Engineering

This report provides a comprehensive description of the research, analysis and design work that The Incompressibles have completed thus far in the senior project process. This document includes all the work that The Incompressibles have completed for the team’s Preliminary Design Review (PDR), Critical Design Review (CDR), the work leading up to the 2019 FPVC competiton and the competition results. This report includes the initial research that the team completed for the fluid power competition, first iterations of designs, final iterations of designs, manufacturing results and processes, and finally testing and results from competition. With a new design for the …

Adapted Trailer Hitching System, Joseph Neil Hearn, Maxwell M. Selna, Maximilian D. Cossalter, Eric B. Ringsrud

Mechanical Engineering

This report highlights the entire design process of an adapted trailer hitching system for Taylor Morris: a navy veteran and quadruple amputee. This begins with problem definition through customer and product research. Objectives are generated after the problem is defined and the boundary of the project is set. This outcome of the project focuses on modifications/improvements to the vehicle side of the problem and leaves the trailers untouched. Engineering specifications are developed to constrain the concept design direction, which ultimately dictates the outcome of the final design. The final design is used as a basis to manufacture a structural prototype …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Final Design Report For Human Powered Vehicle Drivetrain Project, Derek Fromm, Luke Opitz, Michael Juri, Olivier Côté

Mechanical Engineering

The Cal Poly Human Powered Vehicle Club is building a bike to surpass 61.3 mph in 2019. The club and their mentor, George Leone, have proposed a senior project to design, build, and test the drivetrain for this year’s human powered vehicle. Research into human powered vehicles and their drivetrains has shown that the power that a rider can output and the efficiency at which the rider can pedal depend extensively on the design of the drivetrain. Despite the existence of standard bicycle drivetrain designs, the senior project team has found that the best design to meet the club’s requirements …

Investigation Of Design, Manufacture, Analysis, And Test Of A Composite Connecting Rod Under Compression, Thomas Juhl Rohrbach

Master's Theses

Composite materials hold great potential for the replacement of traditional materials in machines utilized on a daily basis. One such example is within an engine block assembly where massive components inherently reduce the efficiency of the system they constitute. By replacing metal elements such as connecting rods, cylinder caps, or a crank shaft with composite alternatives, a significant increase in performance may be achieved with respect to mechanical strength, thermal stability, and durability, while also reducing mass. Exploration of this technology applied to a connecting rod geometry was investigated through a combination of process development, manufacturing, numerical analysis and testing. …

Ares Cleaning System, Andy Sagers, John Cunningham, Peter Greig, Jack Glynn

Mechanical Engineering

In this Final Design Review, the team outlines the general scope of the ARES Cleaning System project and the final design direction chosen and built. This team consists of a group of four mechanical engineering students who have been tasked with designing and manufacturing an autonomous ARES cleaning system to help their sponsor, Fracsun, better track soiling losses measured at large solar arrays. They designed, conceptualized, manufactured, and tested throughout the project as they looked to create a final, functioning product. In creating this Final Design Review, they have identified how the product will perform the desired functions and what …