Applied Mechanics Commons^™

Dynamic Analysis And Fabrication Of A Bi-Stable Structure Designed For Mems Energy Harvesting Applications., Masoud Derakhshani

Electronic Theses and Dissertations

Thanks to the rapid growth in demand for power in remote locations, scientists’ attention has been drawn to vibration energy harvesting as an alternative to batteries. Over the past ten years, the energy harvesting community has focused on bistable structures as a means of broadening the working frequency range and, by extension, the effective efficiency of vibration-based power scavenging systems. In the current study, a new method is implemented to statically and dynamically analyze a bistable buckled, multi-component coupled structure designed specifically for low-frequency vibration energy harvesting systems in both macro and MEMS-scale sizes. Furthermore, several micro-fabrication steps using advanced …

Design Of Structural Stand For High-Precision Optics Microscopy, Sara T. Novell

Master's Theses

Lawrence Livermore National Lab (LLNL) is home to the National Ignition Facility (NIF), the world’s largest and most energetic laser. Each of the 192 beamlines contains dozens of large optics, which require offline damage inspection using large, raster-scanning microscopes. The primary microscope used to measure and characterize the optical damage sites has a precision level of 1 µm. Mounted in a class 100 clean room with a raised tile floor, the microscope is supported by a steel stand that structurally connects the microscope to the concrete ground. Due to ambient vibrations experienced in the system, the microscope is only able …

Fluid Power Vehicle Challenge, Jacob Torrey, Kayla Londono, Bryson Chan, Aaron Trujillo

Mechanical Engineering

The FPVC combines mechanical engineering disciplines to design and manufacture a vehicle that utilizes hydraulic power. The FDR covers the final manufacturing process and verification processes developed during the front end of research and analysis built upon the Critical Design Review (CDR) and the PDR (Preliminary Design Review). This report showcases the design decisions and extensive research that supports the continuing efforts by the Team Pump My Ride, to build upon the accomplishments of Cal Poly’s previous team, The Incompressibles. The FDR presents how Team Pump My Ride produced the design changes from the CDR and PDR to achieve improvements …

Mechanical Properties Of Permanent Foaming Fixatives For Deactivation & Decommissioning Activities, Tristan Maximilian Simoes-Ponce

FIU Electronic Theses and Dissertations

The Department of Energy is investigating fixative technologies that encapsulate and/or immobilize residual contamination in voids during deactivation and decommissioning (D&D). These technologies must have adequate mechanical and adhesion properties to withstand seismic activity that may occur. One solution is the implementation of polyurethane foams used as permanent foaming fixatives (PFF), specifically intumescent foams that contain expandable graphite, making them fire resistant when exposed to extreme heat conditions.

Tensile, compression, seismic, and tensile adhesion testing was done on six commercial-off-the-self polyurethane foams to determine if the expandable graphite and other filler intumescent technologies improve its mechanical limits. It was found …

Footsteps Power Generator, Faisal Alonazi, Mohammed Aljohani

All Undergraduate Projects

This project was motivated by the need for a device that would generate electricity from human motion, especially footsteps. Electricity is a very important resource in our daily life. There are numerous sources from which generate electrical energy. The major sources of energy include but are not limited to coal, natural gas, petroleum, and nuclear energy. Most of these sources have adverse effects on the environmental inclusion such as air pollution; for example, from coal energy generation plants which then cumulatively leads to effects such as increase in rates of global warming. This project seeks to establish an environmentally friendly …

R/C Mini Baja Car: Drive Train And Steering, Carlton R. Mcdonald

All Undergraduate Projects

The purpose of the Baja R/C Car is to compete in the ASME eFX competition in a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race, The Slalom is a test in the steering capability of the vehicle, the Drag is a test in the acceleration of the vehicle in a straight line, and the Baja puts all factors together in a race to test every component of the vehicle. This project is about building an R/C car that not only functions, but also has maximum performance capabilities …

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …