Applied Mechanics Commons^™

Mechanistic Insights Into Polymer-Assisted Graphene Exfoliation: The Roles Of Velocity, Adhesion, Cohesion, Temperature, Peeling Mode, And Edge Defect Via Coarse-Grained Molecular Dynamics, Linjiale Dai

All Theses

Graphene exfoliation is a critical step in the fabrication of high-quality graphene

layers. However, the underlying fracture mechanisms remain poorly understood. In this

work, I employed coarse-grained (CG) molecular dynamics (MD) simulations to

investigate how factors such as interfacial binding energy, substrate cohesion, temperature,

peeling mode, and edge defects influence the outcome of the exfoliation process. To model

polymer-assisted mechanical exfoliation, I used a finite-size system in which multilayer

graphene (MLG) is sandwiched between two thin polymer films. Leveraging the

spatiotemporal efficiency of the CG model, I performed fifty simulation iterations per

parameter set and analyzed the results from a …

Cellulose Recovery From Waste Denim Fabrics Through Indigo Vat Dye Reduction And Spandex Dissolution, Tito N. Venance

Tanzania Journal of Engineering and Technology (TJET)

This study addresses environmental conservation by tackling end-of-life management for post-consumer denim garments through the recycling of cotton fibres from waste denim. The purification process involved dithionite reduction of vat dyes in the presence of an alkali followed by selective dissolution of spandex using N,N-dimethylformamide (DMF). Optimal conditions for dye removal were determined at 90°C for 120 minutes with sodium hydroxide at 25 g/L, sodium dithionite at 6 g/L and PVP at 4.5 g/L, while spandex extraction was achieved using a 5% DMF solution at 70°C for 4 hours. Ultraviolet (UV)-vis spectrophotometric analysis indicated a significant increase in whiteness (DL*). …

Thermo-Elasto-Plastic Stability Of Biaxially Loaded Hollow Rectangular Section Steel Beam-Columns With Applied Torsion, George Adomako Kumi

Civil & Environmental Engineering Theses & Dissertations

Presented herein is an experimental and theoretical study of biaxially loaded hollow rectangular section steel beam-columns with applied torsion at elevated temperatures. The theoretical analysis is based on a system of simultaneous materially nonlinear differential equations of equilibrium for which an iterative semi-analytic solution approach is formulated. Although the primary goal of this research is to study the influence of elevated temperatures on the steel member with the complex loading, rigorous analysis is also conducted of the member at ambient temperature for comparison. The experimental part of the study involves conducting tests on the members at both ambient and high …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Computational Modeling Using A Novel Continuum Approach Coupled With Pathway-Informed Neural Networks To Optimize Dynein-Mediated Centrosome Positioning In Polarized Cells, Arkaprovo Ghosal, Padmanabhan Seshaiyar Dr., Adriana Dawes Dr., General Genomics Inc.

Annual Symposium on Biomathematics and Ecology Education and Research

No abstract provided.

Designing A Cylindrical Capacitive Based Sensor For Monitoring The Table Salt’S Moisture Content During Iodization, Mwajuma Lungo

Tanzania Journal of Engineering and Technology (TJET)

Coaxial cylinder capacitive moisture sensor for determination of moisture content of table salts has been fabricated. The CMS method for determination of moisture content of table salts overcomes the effect of evaporation of iodine in table salt which results from heating in the oven drying method. The CMS overcomes the polarization effect result from the resistive methods of moisture content determination and it is non expensive to construct and it has high accuracy since measurements involves programming system in interpretation of the results. In this research, moisture content sensor based on capacitive principal created using two coaxial cylinders with height …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

Review On Modifications Of Sisal Fibers For Textile Applications, Liberato V Haule

Tanzania Journal of Engineering and Technology (TJET)

Properties of sisal fibers such as high coarseness and poor drapability made the fibers less suitable in production of conventional textiles compared to synthetic fibers. The environmental consciousness and depletion of petrochemical resources have attracted researchers on investigating the use of natural fibers in the industrial production of conventional textiles. Sisal is among highly researched natural fibers due to its features such as strength, recyclability, availability, low processing cost, light weight and ease process ability. This paper reviews possible modifications of sisal fibers to enhance performance in conventional textiles applications

Extraction And Characterization Of Collagen From Cattle Horns For Potential Wound Healing, Yeriko Halson

Tanzania Journal of Engineering and Technology (TJET)

The need for bandages and gauze for wound dressing and healing is inevitable due to the high increase in accidents. Most of the material used for the production of bandages and gauzes for wound healing are from non-renewable synthetic material. The sustainability of non renewable resources is at jeopardy due to the health and associated environmental impact. Consequently, the use of naturally occurring and biodegradable material is a promising solution to the sustainability challenges of synthetic material. In this paper, the extraction of collagen films from cattle horns for potential wound healing is reported. Collagen was extracted from cattle horns …

Preparation And Characterization Of Microporous Cellulose Membranes As Potential Pathogen Filters, Peresi M. Bulemo

Tanzania Journal of Engineering and Technology (TJET)

Growth and development in the textile and fashion industry have resulted in the generation of large amounts of industrial pre consumer textile wastes. It is estimated that 10 to 20% of textile fabrics are wasted during garment manufacturing, with most of the wastes being burned or landfilled. Reusing pre-consumer fabric wastes is therefore considered a viable approach to alleviate environmental impacts associated with their disposal. To achieve a higher porosity membrane, pre-consumer cotton fabrics were partially dissolved in a solution of dimethyl acetamide (DMAc) and lithium chloride (LiCl), and the resulting fibre suspension was utilized to prepare a microporous cellulose …

Cellulose-Keratin Supramolecular Composite: Conformation By Combined Fourier Transform Spectroscopy And Partial Least Square Regression Coefficient, Ngesa Ezekiel Mushi Dr

Tanzania Journal of Engineering and Technology (TJET)

Keratin and cellulose are important nano components with excellent mechanical and biological properties. However, the preparation route through dissolution in organic solvents to make manmade materials is challenging because of their intensive bonding interaction characteristics. Structural modification of the natural attributes is difficult to maintain after polymer regeneration. A new technique by a green route was devised to dissolve keratin from wool, hair, and feather with cellulose in situ using 1-Butyl-3-methylimidazolium chloride [BMIm] + Cl- ionic liquid as a solvent. The mixture of keratin and cellulose homogeneously and synergistically resulted in a supramolecular composite film through non-derivatized mechanochemical interactions. The …

Combustion Characteristics Of Methane, Ethane, Propane, And Butane Blends Under Conditions Relevant Of A Dual-Fuel Diesel And Natural Gas Engine, Christopher Joseph Ulishney

Graduate Theses, Dissertations, and Problem Reports (ETD)

As natural gas production infrastructure is already in place in most of the world and will continue expanding for the foreseeable future, natural gas is an alternative to traditional liquid petroleum fuels in heavy-duty engines. Dedicated natural gas or dual-fuel diesel-natural gas heavy-duty engines are alternatives to diesel-only power generation equipment. One challenge is the large variation in the natural gas composition available for such applications, which is known to significantly affect engine’s combustion characteristics and the emissions composition. As the literature on dual-fuel combustion under low load engine operating conditions that use more realistic natural gas mixtures (i.e., mixtures …

Synthesis, Characterisation And Catalytic Evaluation Of Castor Oil-Templated Mesoporous Sulfated Solid Acid Catalysts For Esterification Reaction, Steven Nyandoro Pr

Tanzania Journal of Engineering and Technology (TJET)

In bio-refinery and other catalytic reactions, heterogeneous catalysts confer advantage over homogenous catalysts due to minimized recovery and separation costs. However, templating surfactant and solid support for the synthesis of heterogeneous catalysts ought to consider their cheap sources and environmentally friendliness for their sustainable use. Thus, with the vision to make the process significantly benign, in the present work, solid acids were synthesised from renewable sources (castor oil as surfactant and rice husk as the source of silica). The synthesised castor oil-templated mesoporous sulfonic acid modified catalysts (SO3H-MTS and SO3H-MT-RHS) were characterised and evaluated for catalytic esterification of acetic acid …

Optimization Of Pulsed Laser Deposition Parameters For Single Crystalline (011) Oriented Tetragonal Pzt Thin Films, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

Recent advances in nanotechnology applications require the processing of high-quality thin films. A systematic study of the optimization of Pulsed deposition parameters for (110) oriented tetragonal PZT thin films is reported in this work. Prior to film deposition, a highly tetragonal Pb(Zr0.5, Ti0.95) or PZT 05/95 was selected to be deposited on (110) oriented Strontium titanate, SrTiO3 substrate, STO(110) to insure small compressive misfit strain. Unlike SRO, the LSOM bottom electrode was then successfully grown at 620 °C, 1.0 J/cm2 and a target-substrate distance of 3.9 cm. Finally, deposition parameters of PZT were progressively optimized through monitoring film morphological changes. …

Properties Of (Cd, Zn)S Films Deposited By Dc Co-Sputtering, Lwitiko P. Mwakyusa

Tanzania Journal of Engineering and Technology (TJET)

CdS thin film is commonly used as a buffer layer in most thin film solar cells. However, the buffer layer with less absorption in the visible region of the solar spectrum as well as that which provides perfect lattice matching with the absorbers is required. The incorporation of Zn in the CdS films can affect the structural and optical properties of the buffer layer. In this work, films of CdS and (Cd,Zn)S films were deposited by DC sputtering utilizing CdS and Zn targets. The concentration of Zn in the CdS was varied by changing the sputtering power of the Zn …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

The Varied Thermal Response Of Magnetic Iron-Oxide Nanoparticles During Induction Heating In Liquid And Solid-Liquid Phase Change Mediums, Joshua Tompkins

Graduate Theses and Dissertations

This study investigates the induction heating response of uncapped iron oxide nanoparticles sonically dispersed as a nanofluid and mechanically distributed in solid phase change materials. The nanoparticles examined have a mean diameter of 14.42 nm and are magnetically heated in an alternating magnetic field at an amplitude of 72.6 kA/m at frequencies of 217, 303, and 397 kHz. Nanoparticle characterization was undertaken through transition electron microscopy, x-ray diffraction, and dynamic light scattering when in suspension. Carrier fluids were characterized through viscosity, heat capacity, and density measurements which were used in the calorimetric calculation of the specific absorption rate (SAR) of …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

Fluid Agitation Studies For Drug Product Containers Using Computational Fluid Dynamics, Matthew Hiroki Ichinose

Master's Theses

At Amgen, the Automated Vision Inspection (AVI) systems capture the movement of unwanted particles in Amgen's drug product containers. For quality inspection, the AVI system must detect these undesired particles using a high speed spin-stop agitation process. To better understand the fluid movements to swirl the particles away from the walls, Computational Fluid Dynamics (CFD) is used to analyze the nature of the two phase flow of air and a liquid solution.

Several 2-D and 3-D models were developed using Fluent to create simulations of Amgen's drug product containers for a 1 mL syringe, 2.25 mL syringe, and a 5 …

Drawing And Twisting Of Graphene Fibers, Gregory T. Lane, Robert J. Sekerak, Isaias Diaz

Mechanical Engineering

The aim of this project was to develop a more automated process for drawing and twisting of graphene fibers than was currently in place. This was implemented by having two chemical baths with variable speed rollers at either end, and intermediate roller to spool fiber between stages, and a twisting cylinder with integral spool to twist the fiber as it is collected. The goal was to have this first iteration deliver a working prototype, however due to manufacturing delays and timing constraints, that will be missed. A second follow-on project would be able to continue the work presented here and …

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

Stabilizing Electrochemical Carbon Capture Membrane With Al2O3 Thin-Film Overcoating Synthesized By Chemical Vapor Deposition, Jingjing Tong, Fengzhan Si, Lingling Zhang, Jie Fang, Minfang Han, Kevin Huang

Faculty Publications

Development of high-efficiency and cost-effective carbon capture technology is a central element of our effort to battle the global warming and climate change. Here we report that the unique high-flux and high-selectivity of electrochemical silver-carbonate dual-phase membranes can be retained for an extended period of operation by overcoating the surfaces of porous silver matrix with a uniform layer of Al₂O₃ thin-film derived from chemical vapor deposition.

Controlling Nanoparticles Formation In Molten Metallic Bilayers By Pulsed-Laser Interference Heating, Mikhail Khenner, Sagar Yadavali, Ramki Kalyanaraman

Mathematics Faculty Publications

The impacts of the two-beam interference heating on the number of core-shell and embedded nanoparticles and on nanostructure coarsening are studied numerically based on the non-linear dynamical model for dewetting of the pulsed-laser irradiated, thin (< 20 nm) metallic bilayers. The model incorporates thermocapillary forces and disjoining pressures, and assumes dewetting from the optically transparent substrate atop of the reflective support layer, which results in the complicated dependence of light reflectivity and absorption on the thicknesses of the layers. Stabilizing thermocapillary effect is due to the local thickness-dependent, steady- state temperature profile in the liquid, which is derived based on the mean substrate temperature estimated from the elaborate thermal model of transient heating and melting/freezing. Linear stability analysis of the model equations set for Ag/Co bilayer predicts the dewetting length scales in the qualitative agreement with experiment.

Formation Of Organized Nanostructures From Unstable Bilayers Of Thin Metallic Liquids, Mikhail Khenner, Sagar Yadavali, Ramki Kalyanaraman

Mathematics Faculty Publications

Dewetting of pulsed-laser irradiated, thin (< 20 nm), optically reflective metallic bilayers on an optically transparent substrate with a reflective support layer is studied within the lubrication equations model. A steady-state bilayer film thickness (h) dependent temperature profile is derived based on the mean substrate temperature estimated from the elaborate thermal model of transient heating and melting/freezing. Large thermocapillary forces are observed along the plane of the liquid-liquid and liquid-gas interfaces due to this h-dependent temperature, which, in turn, is strongly influenced by the h-dependent laser light reflection and absorption. Consequently the dewetting is a result of the competition between thermocapillary and intermolecular forces. A linear analysis of the dewetting length scales established that the non-isothermal calculations better predict the experimental results as compared to the isothermal case within the bounding Hamaker coefficients. Subsequently, a computational non-linear dynamics study of the dewetting pathway was performed for Ag/Co and Co/Ag bilayer systems to predict the morphology evolution. We found that the systems evolve towards formation of different morphologies, including core-shell, embedded, or stacked nanostructure morphologies.

Modeling Diverse Physics Of Nanoparticle Self-Assembly In Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

Presents physics behind dewetting of thin liquid films and mathematical/computational modeling tools (Educational/Research presentation for senior physics majors).

Stability Of A Strongly Anisotropic Thin Epitaxial Film In A Wetting Interaction With Elastic Substrate, Mikhail Khenner, Wondimu T. Tekalign, Margo S. Levine

Mathematics Faculty Publications

The linear dispersion relation for longwave surface perturbations, as derived by Levine et al. Phys. Rev. B 75, 205312 (2007) is extended to include a smooth surface energy anisotropy function with a variable anisotropy strength (from weak to strong, such that sharp corners and slightly curved facets occur on the corresponding Wulff shape). Through detailed parametric studies it is shown that a combination of a wetting interaction and strong anisotropy, and even a wetting interaction alone results in complicated linear stability characteristics of strained and unstrained films.

Stability Of A Strongly Anisotropic Thin Epitaxial Film In A Wetting Interaction With Elastic Substrate, Mikhail Khenner, Wondimu Tekalign, Margo Levine

Mathematics Faculty Publications

The linear dispersion relation for longwave surface perturbations, as derived by Levine et al. Phys. Rev. B 75, 205312 (2007) is extended to include a smooth surface energy anisotropy function with a variable anisotropy strength (from weak to strong, such that sharp corners and slightly curved facets occur on the corresponding Wulff shape). Through detailed parametric studies it is shown that a combination of a wetting interaction and strong anisotropy, and even a wetting interaction alone results in complicated linear stability characteristics of strained and unstrained films.

Morphological Evolution Of Single-Crystal Ultrathin Solid Films, Mikhail Khenner

Mathematics Faculty Publications

An introduction to mathematical modeling of ultrathin solid films and the role of such modeling in nanotechnologies: Educational presentation for senior physics majors

Morphological Evolution Of Single-Crystal Ultrathin Solid Films, Mikhail Khenner

Mathematics Faculty Publications

An introduction to mathematical modeling of ultrathin solid films and the role of such modeling in nanotechnologies: Educational/Research presentation for senior physics majors