Open Access. Powered by Scholars. Published by Universities.®
- Institution
- Keyword
-
- AEDC (1)
- Agriculture (1)
- Art conservation (1)
- Boat tower (1)
- Capacitive sensing (1)
-
- Co-polymer Stabilized Interfaces (CSI) (1)
- Demonstration Model (1)
- Design (1)
- Drop Tower (1)
- Droplet interface bilayer (DIB) (1)
- Dynamic Model (1)
- Dynamics (1)
- Dynamics of Structures (1)
- Engineering (1)
- Fabrication (1)
- Fatigue (1)
- Football (1)
- Helfrich membrane bending (1)
- Helmet (1)
- Impact (1)
- Laser Interferometry (1)
- Mechanical Vibrations (1)
- Mechanical properties of intradroplet interfdaces (1)
- Mechanotransduction (1)
- Membrane based hair cell (1)
- Multi-membrane linear droplet array (1)
- NOCSAE (1)
- Orchard (1)
- Reflectance transformation imaging (1)
- Sensors (1)
- Publication
- Publication Type
Articles 1 - 8 of 8
Full-Text Articles in Applied Mechanics
3-Axis Automated Probe Traverse For Aerodynamic Testing, Tananant Boonya-Ananta, Ricky Wai, Zander Oostman, Teyvon Brooks
3-Axis Automated Probe Traverse For Aerodynamic Testing, Tananant Boonya-Ananta, Ricky Wai, Zander Oostman, Teyvon Brooks
Mechanical Engineering
Our primary objective is to design, build, and test an automated traverse to hold measurement probes in Cal Poly’s low speed wind tunnel. The device should cause minimal flow disturbance. It’s movements must be able to cover eighty percent of the three-dimensional test section. The device should have a mounting point for interchangeable probes. The assembly is to be integrated with the current frame structure on the wind tunnel test section, and should allow very minimal deflection of the measurement probe. The user should be able to control the motion of the traverse via a computer interface which supports automatic …
Dynamic Monitoring And Life Prediction Of Internal Strain-Gage Balances, David Leon Yoder
Dynamic Monitoring And Life Prediction Of Internal Strain-Gage Balances, David Leon Yoder
Masters Theses
Wind tunnel test customers continue to push the limits by producing air vehicle designs that produce high aerodynamic loads at the desired test conditions. These loads are a combination of steady aerodynamic, unsteady aerodynamic, and inertial forces. A methodology to monitor the health of a wind tunnel strain-gage balance has been developed. The objective of this methodology is to define the stress limits of the balance and monitor these limits so the balance can be safely tested without failure of the balance. A balance failure could result in costly damage to the wind tunnel model, support system, and the wind …
Quantifying And Mapping Induced Strain In Canvas Paintings Using Laser Shearography, Philip Klausmeyer, Matthew Cushman, Ivo Dobrev, Morteza Khaleghi, Ellery Harrington, Xiaoran Chen, Cosme Furlong
Quantifying And Mapping Induced Strain In Canvas Paintings Using Laser Shearography, Philip Klausmeyer, Matthew Cushman, Ivo Dobrev, Morteza Khaleghi, Ellery Harrington, Xiaoran Chen, Cosme Furlong
Morteza Khaleghi
Physical Testing Of Potential Football Helmet Design Enhancements, Michael Jeremy Schuster
Physical Testing Of Potential Football Helmet Design Enhancements, Michael Jeremy Schuster
Master's Theses
Football is a much loved sport in the United States. Unfortunately, it is also hard on the players and puts them at very high risk of concussion. To combat this an inventor in Santa Barbara brought a new design to Cal Poly to be tested.
The design was tested in small scale first in order to make some preliminary conclusions about the design. In order to fully test the helmet design; however, full scale testing was required. In order to carry out this testing a drop tower was built based on National Operating Committee on Standards for Athletic Equipment, NOCSAE, …
Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich
Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich
Architectural Engineering
The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.
To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …
Inter-Droplet Membranes For Mechanical Sensing Applications, Nima Tamaddoni Jahromi
Inter-Droplet Membranes For Mechanical Sensing Applications, Nima Tamaddoni Jahromi
Doctoral Dissertations
This dissertation combines self-assembly phenomena of amphiphilic molecules with soft materials to create and characterize mechanoelectrical transducers and sensors whose sensing elements are thin-film bioinspired membranes comprised of phospholipids or amphiphilic polymers. We show that the structures of these amphiphilic molecules tune the mechanical and electrical properties of these membranes. We show that these properties affect the mechanoelectrical sensing characteristic and range of operation of these membrane transducers. In the experiments, we construct and characterize a membrane-based hair cell embodiment that enables the membrane to be responsive to mechanical perturbations of the hair. The resulting oscillations of membranes formed between …
Orchard Bin Atv Trailer, Neil F. Leitz
Orchard Bin Atv Trailer, Neil F. Leitz
All Undergraduate Projects
A local orchardist was experiencing a problem that was being caused by their lack of apple picking bin moving equipment. The orchardist needed a well-engineered solution to this lack of equipment. The solution arrived at was a five bin trailer. There were multiple design requirements for this trailer, including the device needing to be able to interface with an ATV, be able to be loaded by hand, be able to carry five bins, and not exceed a budget of $750. While perfecting the design of the trailer, a number of different disciplines were utilized, which included dynamics, kinematics, static loading …
Flag Raising Device, Josh Quintero
Flag Raising Device, Josh Quintero
All Undergraduate Projects
The motivation for this project stems from a lifetime of boating with father Richard Jones. One problem that many people encounter, including Richard, was when towing someone behind a boat, is the difficulty with handling the warning flag. This flag is used to show other surrounding boats that someone has fallen into the water behind their boat. This warns other boats to stay far away from that area to keep safe from running over the swimmer. Although, when holding the flag in the boat, it can be hard to see at times. The boat driver, or other people standing in …