Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Additives (1)
- Beams and girders (1)
- Cracking (1)
- Deposition (1)
- Dilution (1)
-
- Energy dispersive X ray spectroscopy (1)
- Energy dispersive spectroscopy (1)
- FGMs (1)
- Functional properties (1)
- Functionally graded material (FGM) (1)
- Functionally graded materials (1)
- Hardness (1)
- Intermixing (1)
- LMD (1)
- Laser metal deposition (1)
- Lattice (1)
- Microstructure, Chemical compositions (1)
- Optical microscopes (1)
- SLM (1)
- Scanning electronic microscopes (1)
- Spatial variations, Fabrication (1)
- Steel (1)
Articles 1 - 10 of 10
Full-Text Articles in Metallurgy
Effective Elastic Properties Of Additively Manufactured Metallic Lattice Structures: Unit-Cell Modeling, Okanmisope Fashanu, David Murphy, Myranda Spratt, Joseph William Newkirk, K. Chandrashekhara, Ben Brown, John Porter
Effective Elastic Properties Of Additively Manufactured Metallic Lattice Structures: Unit-Cell Modeling, Okanmisope Fashanu, David Murphy, Myranda Spratt, Joseph William Newkirk, K. Chandrashekhara, Ben Brown, John Porter
Materials Science and Engineering Faculty Research & Creative Works
Lattice structures are lightweight materials, which exhibit a unique combination of properties such as air and water permeability, energy and acoustic absorption, low thermal conductivity, and electrical insulation. In this work, unit-cell homogenization was used to predict the effective elastic moduli of octet-truss (OT) lattice structures manufactured using selective laser melting (SLM). OT structures were manufactured using a Renishaw AM 250 SLM machine with various relative densities. Compression test was carried out at strain rate 5 x 10-3 m-1 using an MTS frame. Finite element analysis was used in the determination of the OT’s effective elastic properties. Results …
Comparison Of Fatigue Performance Between Additively Manufactured And Wrought 304l Stainless Steel Using A Novel Fatigue Test Setup, M. M. Parvez, Y. Chen, Joseph William Newkirk, Frank W. Liou
Comparison Of Fatigue Performance Between Additively Manufactured And Wrought 304l Stainless Steel Using A Novel Fatigue Test Setup, M. M. Parvez, Y. Chen, Joseph William Newkirk, Frank W. Liou
Materials Science and Engineering Faculty Research & Creative Works
In this research, a novel adaptive controlled fatigue testing machine was designed for bending type high cycle fatigue test. A unique dual gauge section Krouse type mini specimen was designed for simply supported transverse bending. Displacement controlled fatigue tests were implemented using an electromechanical actuator. The variation in the control signal and load observed during the test provides unique insights into realizing the deterioration of the specimen due to fatigue. These analyses were utilized to compare the fatigue performance of wrought and additively manufactured 304L stainless steel. The influence of the build direction on fatigue performance was also investigated by …
Elevated Temperature Mechanical And Microstructural Characterization Of Slm Ss304l, G. R. Hecht, Sriram Praneeth Isanaka, Joseph William Newkirk
Elevated Temperature Mechanical And Microstructural Characterization Of Slm Ss304l, G. R. Hecht, Sriram Praneeth Isanaka, Joseph William Newkirk
Materials Science and Engineering Faculty Research & Creative Works
SLM built SS304L was annealed and water quenched to minimize residual stress and avoid carbide precipitation. Mini-tensile characterization of strength and elongation at temperature conditions up to 800°C, along with observations of the associated microstructural transformations were utilized to understand the changes produced in SLM SS304L. As-built and annealed specimens were found to exhibit decreasing strength and elongation with increasing temperature as expected. Carbide precipitates appeared after short times at high temperatures within both as-built and annealed specimens for all cases, but no brittle intermetallic phase development was observed for any of the temperatures investigated. While the lack of Sigma, …
Compressive And Bending Performance Of Selectively Laser Melted Alsi10mg Structures, D. Murphy, O. Fashanu, Myranda Spratt, Joseph William Newkirk, K. Chandrashekhara, H. Misak, D. Klenosky
Compressive And Bending Performance Of Selectively Laser Melted Alsi10mg Structures, D. Murphy, O. Fashanu, Myranda Spratt, Joseph William Newkirk, K. Chandrashekhara, H. Misak, D. Klenosky
Materials Science and Engineering Faculty Research & Creative Works
Selective laser melting (SLM) is a widely used additive manufacturing technique that effectively manufactures complex geometries such as cellular structures. However, challenges such as anisotropy and mechanical property variation are commonly found due to process parameters. In a bid to utilize this method for the commercial production of cellular structures, it is important to understand the behavior of a material under different loading conditions. In this work, the behavior of additively manufactured AlSi10Mg under compression, bending, and tension loads was investigated. Vertical and horizontal build directions are compared for each type of loading. Specimens were manufactured using the reduced build …
Development Of An Engineering Diagram For Additively Manufactured Austenitic Stainless Steel Alloys, Zachary T. Hilton, Joseph William Newkirk, Ronald J. O'Malley
Development Of An Engineering Diagram For Additively Manufactured Austenitic Stainless Steel Alloys, Zachary T. Hilton, Joseph William Newkirk, Ronald J. O'Malley
Materials Science and Engineering Faculty Research & Creative Works
Austenitic stainless steels are the most widely applied types of stainless steels, due to their good weldability and high corrosion resistance. A number of engineering diagrams exist for the purpose of providing insight into the behavior of these steels. Examples of these diagrams are constitution diagrams (aka Schaeffler Diagrams) which are used to approximate the solidification path of the alloy and the amount of retained ferrite in the solidified matrix. Other diagrams are the Suutala diagram, which approximates cracking susceptibility, and microstructural maps, which predict the solidification path by varying a processing parameter, such as cooling rate. By combining these …
Effect Of Wall Thickness And Build Quality On The Compressive Properties Of 304l Thin-Walled Structures Fabricated By Slm, Myranda Spratt, Sudharshan Anandan, Rafid M. Hussein, Joseph William Newkirk, K. Chandrashekhara, Heath Misak, Michael Walker
Effect Of Wall Thickness And Build Quality On The Compressive Properties Of 304l Thin-Walled Structures Fabricated By Slm, Myranda Spratt, Sudharshan Anandan, Rafid M. Hussein, Joseph William Newkirk, K. Chandrashekhara, Heath Misak, Michael Walker
Materials Science and Engineering Faculty Research & Creative Works
The specific strength of lightweight lattice structures built with SLM is of interest to the aerospace industry. Honeycombs were manufactured with increasing wall thicknesses (which increases density) and tested under compression. The optimal strength to density ratio was determined from the resulting data. The build quality was also evaluated to determine how/if the results were influenced by the specimen quality. Differences between the nominal and as-built geometry were identified, but considered to be minimal. Microstructural evaluation of the specimens revealed a possible dependence on the ‘border scan’ properties, as the thickness of the specimens was such that the board scan …
Fast Prediction Of Thermal History In Large-Scale Parts Fabricated Via A Laser Metal Deposition Process, Lei Yan, Tan Pan, Joseph William Newkirk, Frank W. Liou, Eric E. Thomas, Andrew H. Baker, James B. Castle
Fast Prediction Of Thermal History In Large-Scale Parts Fabricated Via A Laser Metal Deposition Process, Lei Yan, Tan Pan, Joseph William Newkirk, Frank W. Liou, Eric E. Thomas, Andrew H. Baker, James B. Castle
Materials Science and Engineering Faculty Research & Creative Works
Laser metal deposition (LMD) has become a popular choice for the fabrication of near-net shape complex parts. Plastic deformation and residual stresses are common phenomena that are generated from the intrinsic large thermal gradients and high cooling rates in the process. Finite element analysis (FEA) is often used to predict the transient thermal cycle and optimize processing parameters; however, the process of predicting the thermal history in the LMD process with the FEA method is usually time-consuming, especially for large-scale parts. Herein, multiple 3D FEA models with simple assumptions on the heat source and its loading methods are compared and …
Design And Fabrication Of Functionally Graded Material From Ti To Γ-Tial By Laser Metal Deposition, Xueyang Chen, Lei Yan, Joseph William Newkirk, Frank W. Liou
Design And Fabrication Of Functionally Graded Material From Ti To Γ-Tial By Laser Metal Deposition, Xueyang Chen, Lei Yan, Joseph William Newkirk, Frank W. Liou
Materials Science and Engineering Faculty Research & Creative Works
Functionally graded material (FGM) is one kind of advanced material characterized by a gradual change in properties as the position varies. The spatial variation of compositional and microstructure over volume is aimed to control corresponding functional properties. In this research, when 100% γ-TiAl was directly deposited on pure Ti substrate, cracks were formed within the γ-TiAl layer. Then a six-layer crack-free functionally graded material of Ti/TiAl was designed and fabricated by laser metal deposition (LMD) method, with composition changing from pure Ti on one side to 100% γ-TiAl on the other side. The fabricated FGM was characterized for material properties …
Studying Chromium And Nickel Equivalency To Identify Viable Additive Manufacturing Stainless Steel Chemistries, Zachary T. Hilton, Joseph William Newkirk, Ronald J. O'Malley
Studying Chromium And Nickel Equivalency To Identify Viable Additive Manufacturing Stainless Steel Chemistries, Zachary T. Hilton, Joseph William Newkirk, Ronald J. O'Malley
Materials Science and Engineering Faculty Research & Creative Works
Chromium and nickel equivalency modeling has long been used in welding to determine the weldability of steel chemistries. A study was conducted to determine the applicability of Cr-Ni modeling to the additive manufacturing process. Many AM methods involve rapid solidification of small melt pools, similar to welding. Chemistries with varying Cr/Ni ratios were selected for use in a selective laser melting process and modeled using known models. Initial results indicate that the standard "safe welding zone" may not directly apply to additive manufacturing. The capability to build with chemistries outside the weldability “safe zone” could result in improved and varied …
Functionally Graded Materials By Laser Metal Deposition (Preprint), Syamala R. Pulugurtha, Joseph William Newkirk, Frank W. Liou, Hsin-Nan Chou
Functionally Graded Materials By Laser Metal Deposition (Preprint), Syamala R. Pulugurtha, Joseph William Newkirk, Frank W. Liou, Hsin-Nan Chou
Materials Science and Engineering Faculty Research & Creative Works
Fabrication of functionally graded materials (FGMs) by laser metal deposition (LMD) has the potential to offer solutions to key engineering problems over the traditional metalworking techniques. But the issues that need to be addressed while building FGMs are intermixing in the layers and cracking due to the residual stresses. This paper is to present the study of the effect of process parameters (laser power and travel speed) on the degree of dilution between the substrate (or, previous layer) and powder material for few metallurgical systems.