Engineering Mechanics Commons^™

Percolation-Induced Thermo-Rheological Transitions In Biobased Graphene Nanoplatelet Nanofluids, Abiodun A. Saka, Tobechukwu K. Abor, Anthony C. Okafor, Monday U. Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Biobased lubricants with thermally responsive rheology are increasingly needed for high-efficiency mechanical systems. Graphene nanoplatelet (GnP) nanofluids in vegetable oils are promising candidates, yet their percolation-driven thermo-rheological transitions remain insufficiently understood. In particular, the coupled concentration–temperature landscape controlling network-mediated flow transitions has not previously been established. Here, surfactant-free GnP nanofluids were prepared in high-oleic soybean oil (HOSO) at concentrations of 0.025–2.15% v/v (ϕ), and their rheological response was mapped between 25°C and 80 °C under steady-shear and oscillatory conditions. Below the percolation threshold (ɸ ≤ 0.1% v/v), the nanofluids exhibit near-Newtonian behavior, moderate reversible viscosity enhancement, and classical Arrhenius-type temperature …

Magnetic Field-Induced Transformation In Polycrystalline Ni2mnal Heusler Type Magnetic Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The martensitic and magnetic transformations, as well as the mechanical properties, of Ni₂MnAl alloys in as-cast (AC) and heat-treated (HT) conditions were investigated. Magnetic-field-induced strain was evaluated via magnetostriction, with reversible strains of 0.14% and 0.2% achieved in the martensitic phase at 2 K for the AC and HT alloys, respectively. Transformation temperatures and Curie temperatures were determined under constant applied magnetic field, revealing that γ-phase inclusions in the AC microstructure suppress antiferromagnetic domain response, yielding a lower magnetization (∼8.4 emu g⁻¹) compared to the HT alloy (∼13.4 emu g⁻¹). Both alloys exhibited hysteretic behavior in the martensitic state and …

Evaluation Of The Effect Of Vibration On Signal Reflection In Coaxial Cable Connectors For Vibration Sensing In Aircraft Structures And Systems, Saidanvar Esanjonovich Valiev, Anthony C. Okafor, Jeremiah J. Rittenhouse, Daniel S. Stutts, Jie Huang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper investigates the effects of vibration on signal reflection (S11) in aerospace data transmission line (ADTL) and commercial data transmission line (DTL) connectors for their alternative use as vibration sensors. The impact of vibration on the S11 signal was investigated on five ADTL and four DTL connectors at six vibration frequencies (20 Hz, 40 Hz, 80 Hz, 160 Hz, 320 Hz, and 640 Hz) and four vibration accelerations (0.5G, 1 G, 2 G, and 4G). The experiment was conducted using a split-plot design with a cable type assigned as the main-plot factor, with vibration frequency and acceleration as subplot …

Distributed Vibration Sensing For Identification Of Loose Connectors In Coaxial Data Transmission Lines, Saidanvar Esanjonovich Valiev, Anthony C. Okafor, Jeremiah J. Rittenhouse, Jie Huang, Daniel S. Stutts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This study investigates the effect of vibration-induced loose connections on signal reflection (S11) for loose connection identification in aerospace coaxial cables using distributed sensing approach, which is effective in filtering the noise and identifying minor discontinuities. In this approach, a sliding gated window is applied to S11 signal, a fast Fourier transform is performed over the gated windows, cross-correlation is computed between the baseline and vibration-affected signals, and the standard deviation is mapped along the cable length. Sinewave signals from 9 kHz to 5 GHz were swept through cables with vibrating connectors under three conditions: fully tightened, loosened by 180°, …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Extraction Of Aluminum From Lunar Regolith Through Molten Salt Electrolysis, Jacob N. Ortega, Todd P. Sander, Jeffrey D. Smith, Fateme Rezaei, David J. Bayless, William Schonberg, Daniel S. Stutts, Frank D. Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents the methodology, development, and results of an end-to-end regolith-to-metal concept for producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method. Using electrolytic reduction, aluminum oxide (i.e., alumina) can be reduced into aluminum and oxygen via electrolysis in a molten salt bath. A steady supply of hydrogen chloride could allow this in-situ resource utilization (ISRU) method to supply several necessary materials consumed in the electrolytic reduction step of the process to produce bulk aluminum metal, oxygen, water, and silica from anorthite abundant in lunar highland regions. In this …

Detection Of Bacterial Genomic Dna Fragments Using The Mxene Crispr-Cas9 Field-Effect Transistor, Jiaoli Li, Ali Taheri, Weijia Liu, Ying Zhuo, Pengfei Ma, Chenglin Wu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Clustered regularly interspaced short palindromic repeats (CRISPR)-based field-effect transistor (FET) sensors provide a promising platform for highly specific and amplification-free nucleic acid detection. However, their direct application in identifying target sequences within intact genomic DNA remains underexplored. We developed a CRISPR-Cas9 FET sensor for detecting DNA sequences by immobilizing Cas9 onto a graphene-MXene sensing interface via (3-aminopropyl)triethoxysilane (APTES) functionalization. The sensor targeted Stx1, a 440 bp laboratory-amplified fragment associated with Shiga toxin production in pathogenic E. coli. Gel electrophoresis confirmed the precise cleavage of Stx1, while the nontarget sequence Stx2 remained undetected. FET measurements further validated the sensor's specificity, showing …

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Thermo-Rheological And Tribological Properties Of Low- And High-Oleic Vegetable Oils As Sustainable Bio-Based Lubricants, Abiodun Saka, Tobechukwu K. Abor, Anthony C. Okafor, Monday U. Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Vegetable oil-based lubricants have attracted increased research attention in recent decades as sustainable alternatives to conventional petroleum-based lubricants in metal machining. However, more studies are required to fully elucidate the thermo-rheological and tribological properties. This study presents an investigation of the thermo-rheological and tribological properties of different vegetable oils, including low- and high-oleic soybean oil, high-oleic sunflower, safflower, and canola oils. The lubricity, and evolution of viscosity and thermodynamic properties as a function of temperature were investigated to obtain important parameters including the viscosity index, flow behavior index, flow activation energy, specific heat capacity, thermal conductivity, coefficient of friction, contact …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Identification Of Corrosion Damage, Vibration, And Loose Conections In Aircraft Data Transmission Lines Using Reflected And Transmitted Signals; Formulation Of Vegetable Oil-Based Nanofluids As Cutting Fluids For Mql Machining, Saidanvardzhon Valiev

Doctoral Dissertations

This research presents a novel Frequency Domain Transmitometry (FDT) method that uses transmitted signals (S21) to detect and characterize aircraft data transmission lines (ADTL) corrosion damage without additional reflectometry circuitry. Corrosion experiments were conducted according to ASTM G85-A5 over 14 weeks. Combined FDT and reflected signals (S11) analyses revealed distinct three-peak signatures associated with damage and corrosion. The square root of the Area Under the Curve (AUC) of the FDT damage peak and the Full Width at Three-Quarter Maximum (FW3QM) of the S11 damage peak is correlated with corrosion propagation depth and width. S11 signals were further used for vibration …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO2, MoS2, and Al2O3) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment of 10 °C. Obtained results showed that thermal …

Tough Monolayer Silver Nanowire-Reinforced Double-Layer Graphene, Yanxiao Li, Congjie Wei, Steven E. Kooi, David Veysset, Chuanrui Guo, Yuxiang Gan, Ying Zhuo, Genda Chen, Mohammad Naraghi, Keith A. Nelson, Chenglin Wu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Mixed-dimensional nanomaterials composed of one-dimensional (1D) and two-dimensional (2D) nanomaterials, such as graphene-silver nanowire (AgNW) composite sandwiched structures, are promising candidates as building blocks for multifunctional structures and materials. However, their mechanical behavior and failure mechanism have not yet been fully understood. In this work, we have performed integrated experimental, theoretical, and numerical studies to explore the performance and failure modes of graphene-AgNW composite under tensile and impact loading conditions. In situ tensile tests using a nano indenter, implemented with a push-to-pull device and a laser-induced projectile impact test system, are used to shed light on load-bearing mechanisms in graphene-AgNW …

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Influence Of Nanofiller Surface Treatment On Mechanical Properties Of Pyrolyzed Ceramic Nanocomposites, Laxmi Sai Viswanadha, Chenglin Wu, Jeremy Watts, Mohammad Naraghi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The brittleness and limited plastic deformation of ceramics restrict their applications. In this work, the effects of pristine (CNTP), functionalized (CNTOH, CNTCOOH) and silanized MWCNTs on the mechanical properties of Silicon Carbide obtained by pyrolyzing polycarbosilane SMP-10 were studied. Functionalization with 3-glycidoxypropyltrimethoxy was analyzed through dispersion stability, zeta potential, and EDS analyses, revealing increased silicon content and colloidal stability in silanized MWCNTs. However, silanized MWCNTs led to reduced mechanical properties in composites, while untreated MWCNTs (CNTP, CNTOH, CNTCOOH), showed a substantial increase in modulus by 74.2 %, 86.9 %, and 30.5 %, respectively. The observed enhancement in mechanical properties exceeded …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. The end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …

Internal Structure And Breakage Behavior Of Biogenic Carbonate Sand Grains, Elieh Mohtashami, C. Guney Olgun, Chenglin Wu, Tara Selly

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Study Investigates the Mechanical Behavior of Biogenic Carbonate Sands from Puerto Rico at Grain-Scale Level. Micro-Computed Tomography Has Also Been Used to Get Insights on the Internal Structure of These Particles Before and after Loading. the Crushing Strength of These Particles Are Smaller Comparing to the Values Reported for Silica Sands. It Has Also Been Shown that These Particles Have Complex Internal Structure Including a Network of Pores Connected with Channels. This Study Also Demonstrates the Effect of Intragrain Structure of Biogenic Carbonate Sands and Shows How Internal Grain Structure Plays a Role on Particle Fracture.

Effects Of Fiber Clustering On Fatigue Behavior Of Steel Fiber Reinforced Concrete Beams, Danying Gao, Zhiqiang Gu, Congjie Wei, Chenglin Wu, Yuyang Pang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper investigated the effects of fiber clustering on fatigue behavior of steel-fiber-reinforced concrete (SFRC) beams with reinforcements by experimental and numerical analysis. The steel fiber volume fractions of beams were 0 vol%, 0.5 vol%, 1.0 vol%, and 1.5 vol%. One beam was tested under static loading, and eight beams under fatigue loading with different stress levels. Moreover, the fiber distribution in the cross section of concrete was experimentally characterized to understand the underlying mechanism. The results indicated that the fatigue life of beam increased with increasing fiber volume fraction from 0 to 1.0 vol% and decreased from 1.0 vol% …

Spherical Cavity Expansion Approach For The Study Of Rigid-Penetrator’S Impact Problems, Mario Buchely, Alejandro Marañon

Materials Science and Engineering Faculty Research & Creative Works

In recent years, Spherical Cavity Expansion (SCE) theory has been extensively utilized to model dynamic deformation processes related to indentation and penetration problems in many fields. In this review, the SCE theory is introduced by explaining the different mathematical features of this theory, its solution, and a potential application to model the penetration of a rigid penetrator into a deformable target. First, a chronologically literature review of the most common models used to study this kind of penetration problems is introduced, focusing on the SCE theory. Then, the engineering model of penetration is presented using the SCE approach. The model …