Engineering Mechanics Commons^™

Percolation-Induced Thermo-Rheological Transitions In Biobased Graphene Nanoplatelet Nanofluids, Abiodun A. Saka, Tobechukwu K. Abor, Anthony C. Okafor, Monday U. Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Biobased lubricants with thermally responsive rheology are increasingly needed for high-efficiency mechanical systems. Graphene nanoplatelet (GnP) nanofluids in vegetable oils are promising candidates, yet their percolation-driven thermo-rheological transitions remain insufficiently understood. In particular, the coupled concentration–temperature landscape controlling network-mediated flow transitions has not previously been established. Here, surfactant-free GnP nanofluids were prepared in high-oleic soybean oil (HOSO) at concentrations of 0.025–2.15% v/v (ϕ), and their rheological response was mapped between 25°C and 80 °C under steady-shear and oscillatory conditions. Below the percolation threshold (ɸ ≤ 0.1% v/v), the nanofluids exhibit near-Newtonian behavior, moderate reversible viscosity enhancement, and classical Arrhenius-type temperature …

Extraction Of Aluminum From Lunar Regolith Through Molten Salt Electrolysis, Jacob N. Ortega, Todd P. Sander, Jeffrey D. Smith, Fateme Rezaei, David J. Bayless, William Schonberg, Daniel S. Stutts, Frank D. Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents the methodology, development, and results of an end-to-end regolith-to-metal concept for producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method. Using electrolytic reduction, aluminum oxide (i.e., alumina) can be reduced into aluminum and oxygen via electrolysis in a molten salt bath. A steady supply of hydrogen chloride could allow this in-situ resource utilization (ISRU) method to supply several necessary materials consumed in the electrolytic reduction step of the process to produce bulk aluminum metal, oxygen, water, and silica from anorthite abundant in lunar highland regions. In this …

Effects Of Cutting Conditions On Tool Temperature And Material Removal Rate In Turning Operations, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Cutting conditions in manufacturing processes have effects on tool temperature and material removal rate. The objective of this study was to investigate the effects of cutting conditions namely spindle speed, feed rate, depth of cut and tool nose radius on tool temperature and material removal rate in turning operations. A total of 81 experiments were conducted to measure tool temperature and material removal rate in order to determine the effects of cutting conditions on tool temperature and material removal rate using ANOVA and regression analysis. The results show that tool nose radius, depth of cut, and spindle speed are significant …

Cellulose Recovery From Waste Denim Fabrics Through Indigo Vat Dye Reduction And Spandex Dissolution, Tito N. Venance

Tanzania Journal of Engineering and Technology (TJET)

This study addresses environmental conservation by tackling end-of-life management for post-consumer denim garments through the recycling of cotton fibres from waste denim. The purification process involved dithionite reduction of vat dyes in the presence of an alkali followed by selective dissolution of spandex using N,N-dimethylformamide (DMF). Optimal conditions for dye removal were determined at 90°C for 120 minutes with sodium hydroxide at 25 g/L, sodium dithionite at 6 g/L and PVP at 4.5 g/L, while spandex extraction was achieved using a 5% DMF solution at 70°C for 4 hours. Ultraviolet (UV)-vis spectrophotometric analysis indicated a significant increase in whiteness (DL*). …

Thermo-Rheological And Tribological Properties Of Low- And High-Oleic Vegetable Oils As Sustainable Bio-Based Lubricants, Abiodun Saka, Tobechukwu K. Abor, Anthony C. Okafor, Monday U. Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Vegetable oil-based lubricants have attracted increased research attention in recent decades as sustainable alternatives to conventional petroleum-based lubricants in metal machining. However, more studies are required to fully elucidate the thermo-rheological and tribological properties. This study presents an investigation of the thermo-rheological and tribological properties of different vegetable oils, including low- and high-oleic soybean oil, high-oleic sunflower, safflower, and canola oils. The lubricity, and evolution of viscosity and thermodynamic properties as a function of temperature were investigated to obtain important parameters including the viscosity index, flow behavior index, flow activation energy, specific heat capacity, thermal conductivity, coefficient of friction, contact …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO2, MoS2, and Al2O3) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment of 10 °C. Obtained results showed that thermal …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Nanoscale Modeling Of Membrane Systems Under Mechanical Deformation In Traumatic Brain Injury Using Molecular Dynamics, Anh Thi Ngoc Vo

Theses and Dissertations

Neuronal membrane disruption and mechanoporation are nanoscale damage mechanisms that critically affect brain cell viability during traumatic brain injury (TBI). These nanoscale cellular impairments are elusive in experiments and necessitate in silico approaches such as molecular dynamics (MD) simulations. Implementing MD, this research aims to investigate the effects of different key factors related to membrane deformation and damage, including force field resolutions, lipid compositions, and loading conditions.

To examine the impact of force field resolution, MD deformation simulations were conducted on 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC) lipid bilayer membranes, using all-atom (AA), united-atom (UA), and coarse-grained Martini (CG-M) force fields. The mechanical responses …

The Fourth Industrial Revolution: Opportunities And Challenges To The Future Of Mechanical Engineering, Ulingeta O.L. Mbamba

Tanzania Journal of Engineering and Technology (TJET)

This paper provides a conceptual overview of the developments of the Fourth Industrial Revolution (4IR) and derives challenges and opportunities for the future of the mechanical engineering profession. The paper broadly defines 4IR as the fusion of technologies and interaction across physical, digital and biological aspects, while defining mechanical engineering as "a multi-faceted discipline that encompasses the teaching, practice and guidance of others in the development and application of scientific principles to mechanical systems". The paper looks specifically at developments in the Internet of Things (IoT), blockchain technology, robotics, Big Data analytics, biotechnology, nanotechnology, 3D printing and artificial intelligence and …

Designing And Manufacturing Of Vegetable Slicing Machine, Juma Nuhu Msuya

Tanzania Journal of Engineering and Technology (TJET)

Agro-processing industry is faced with a challenge of slicing of vegetables for immediate consumption. This stems from the fact that the traditional slicing methods use bare hands, and knives. This method is faced with shortcomings of inefficiency, poor hygiene, and significant dangers to injury. If vegetables are not sliced, their drying takes longer, may possibly be spoiled, and cannot be stored for future uses. Therefore, this paper strives to design a vegetable slicing machine to increase the efficiency of the drying process as a post-processing step. The study employed a Pugh’s design model to design the machine and manufacture it. …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Electrochemical Deposition In Energy Storage Devices, Witness Atutala Martin

Graduate Theses and Dissertations

Metals, whether in a solid or soluble ion form, are a vital part of any electrochemical storage system. More so, Li metal is widely considered as the ideal anode because of its low density and low electrochemical potential (-3.04 V vs. the standard hydrogen electrode – SHE). However, just like most metals, it does not plate or strip evenly during cycling which can lead to cycling performance issues, short cycling lifespans, and even safety concerns brought about by dendrites that can cause internal short-circuiting within cells. This research focused on investigating the electroplating of metals in both aqueous and non-aqueous …

An Improved Foam Modeling Technique And Its Application To Petroleum Drilling And Production Practice, Yanfang Wang

LSU Doctoral Dissertations

Foam is one of the most common used multiphase fluid in Underbalanced Drilling (UBD) and Managed Pressure Drilling (MPD). Because of its low density, high capacity of lifting and carrying cuttings, low cost and compatibility with formations, foam has become more superior than the conventional drilling mud when depleted reservoir pressure, severe lost circulation, or unstable borehole are encountered. In general, the success of foam applications rely on the understanding of the fundamentals of foam rheology in downhole conditions.

Foam rheology has been studied for decades. Conventional foam rheological models such as Power Law, Bingham Plastic, Herschel-Bulkley to explain foam …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Influence Of Tempering And Cryogenic Treatment On Retained Austenite And Residual Stresses In Carbonitrided 18crnimo7-6 Low Alloy Steel, Richard Katemi

Tanzania Journal of Engineering and Technology (TJET)

This work investigated the influence of tempering conditions coupled with cryogenic treatment on thermal stabilization of retained austenite and residual stress distributions in carbonitrided 18CrNiMo76 low alloy steel samples. The carbonitriding conditions were set to enable attaining surface carbon and nitrogen content of 0.87 and 0.34 mass.-percent respectively. After carbonitriding, some of the samples were subjected to varying tempering conditions followed by cryogenic treatment at-120 °C using nitrogen gas. Analysis of both retained austenite and residual stresses was conducted using X-ray diffraction. In the as-quenched state, carbonitrided samples contained 52 mass.-percent. Samples that were directly subjected to the cryogenic treatment …

Group Iv Environmentally Benign, Inexpensive Semiconductor Nanomaterials For Solar Cells, Lisa Je

ENGS 86 Independent Projects (AB Students)

Modern solar cells are composed of silicon, cadmium tellurium, and copper indium gallium diselenide. While these materials are efficient, elements such as cadmium and indium are rare and expensive. To make this renewable energy source more inexpensive and sustainable, the Liu Optics lab is substituting expensive rare earth metals for more commonly found transition state metals. Work has been done to replace the solar cell layers composed of cadmium and gallium to replace them with glass, silicon, and/or thin films. Common metals such as germanium and tin are investigated and characterized to provide a platform for solar cell components.

Properties Of Matter, Mike Jackson, Holly Haney

High School Lesson Plans

Students will investigate the relationship(s) between thermal and electrical properties of matter. First, students will use a multimeter and temperature probe to investigate the relationship between electrical resistance and temperature of an electrical resistor composed of metals. They will then graph collected data to analyze the relationship and draw a conclusion as to their relationship. They will then perform the same investigation on a thermal resistor made of a semiconducting substance and analyze that collected data. Finally, using ClaimEvidence-Reasoning (CER) structure, students will use their experimental evidence to state the similarities and differences between the electro-thermal properties of metals and …

An Analysis Of Common Drill Stem Vibration Models, Mohammed F. Al Dushaishi, Runar Nygaard, Daniel S. Stutts

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Excessive drill stem (DS) vibration while rotary drilling of oil and gas wells causes damages to drill bits and bottom hole assemblies (BHAs). In an attempt to mitigate DS vibrations, theoretical modeling of DS dynamics is used to predict severe vibration conditions. To construct the model, decisions have to be made on which beam theory to be used, how to implement forces acting on the DS, and the geometry of the DS. The objective of this paper is to emphasize the effect of these assumptions on DS vibration behavior under different, yet realistic, drilling conditions. The nonlinear equations of motion …

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Discrete Element Modelling Of The Abrasive Dehulling Process Of Sorghum And Millet, E. L. Lazaro

Tanzania Journal of Engineering and Technology (TJET)

The abrasive dehulling process of sorghum and millet was modelled using a three-dimensional discrete element model. The model was validated by comparison between experimental and simulation results. Good correlation between experimental and simulation results was obtained. Several numerical experiments were also carried out using the developed model to investigate the influence of mill and grain parameters on dehulling of sorghum and millet. The simulated results correlated well with experimental results from literature. The developed model therefore provides a simple and cheap tool, which can be used to study the dehulling process in more detail than, is currently possible using the …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Xiaolong Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fundamental issues related to the selection of a metallic fuel casting furnace design are presented and discussed including heating mechanisms, casting issues, crucible design, and issues related to the mass transport of americium. The process of evaluating all of these different criteria is undertaken to select a concept that would have the greatest chance of success for casting americium in a metallic fuel rod. Based on this evaluation process, a concept for the casting of metallic fuel pins containing high vapor pressure materials is selected and discussed. The important physics of this concept include mass transport of americium from the …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Design Approach For Small Scale Continuous, Steady State Plants, O Kaunde

Tanzania Journal of Engineering and Technology (TJET)

One of the major steps in the design of a process plant is development of an appiopriate flowsheet. At this step, the technical solutions may be con- sidered in relation to the social and economic factors. In this paper, guide- lines for developing a flowsheet for continuous, steady State process in a developing country environment have been proposed. To illustrate the pro- posed guidelines, a case study involving design of an ethanol distillation plant has been used.

Improved Heat Transfer By Means Of Steam Injection In A Shell & Tube Heat Exchanger, O Kaunde

Tanzania Journal of Engineering and Technology (TJET)

When designing a heat exchanger; one aims at attaining high heat transfer rates SO as to minimise heat transfer area and therefore the overall cost. This paper presents a method of improving the overall heat travsfer coef- ficient of a conventional shell and tube heal exchanger. The method in- volves injecting steam into the process fluid as it enters the heat exchanger thus effecting mixing of fluid as it travels along the exchanger Tests car- • ried out using this technique showed a significant increase in the overall heat transfer coefficient values.

Influence Of Arc Discharge Duration On Turbulent Mass Burning Rate, E Mushi

Tanzania Journal of Engineering and Technology (TJET)

The influence of arc discharge duration on turbulent mass burning rate was investigated for turbulent r.m.s vglocities of u '=1.73 m/s and u'=4.5 nfs. Methane air mixtures were used at equivalence ratios ranging from 0.83 to / .25. Flame size was obtained through schiieren photography while the intensity Of CH chemiluminescence emissions was used to measure mass burning rate. A variable spark duration unit was used for ignition sparks and all the experiments were done in a fan stirred bomb. Discharge duration has no effect when the equivalence ratio is I. For higher values longer duration inoeases the burning rate …

An Alternative Method Of Interfacing A Dc Motor To A Microprocessor For Mo- Tion Control, M Selekwa

Tanzania Journal of Engineering and Technology (TJET)

A Simple and cheap alternative method Of interfacing a permanent mag- net dc motor to a motion control using switch- ing transistor motor drivers is presented. This method involves the use Of very few transistor-transistor logic (TTL) devices and a 555 timer to pro- duce a pulse width modulated (P WM) signal which is required by the mo- ror driver. The motor driver in this case should be of an H-bridge type. Like other methods currently in use, it relieves the MPU of all timing func- tions which are necessary in the generation of P WM signals. The present method, …

Thermodynamics And Transport Proper- Ties Analysis Of Natural Gas From Songosongo In Kilwa- Tanzania, G Mrema

Tanzania Journal of Engineering and Technology (TJET)

Analysis ofthermodynamics and transport properties was carried outfor six natu- ral gas samples from Songosongofield in Kilwa - Tanzania using PRO/II simula- for. Properties of most interest in gas processing (due to their influence on the sales value) such as density, specific gravity, critical parameters, bubble point and dew point, enthalpy, latent heat of vaporisation, molecular weight, boiling point and phase were investigated. In addition composition of the gas was com- pared with that from elsewhere. The gas was assumed to be at a temperature of 30C and a pressme of 150 bar before pressure let down station. Results indicated …