Engineering Science and Materials Commons^™

Castrip Process Technology: Non-Grain Oriented (Ngo) Si Steels Extension And Carbide-Free Bainitic (Cfb) For Flat Products, Naram Naidu Meesala

Masters Theses

"This research explores the development of advanced steel grades manufactured through Castrip® twin-roll thin strip casting technology, with particular attention to non-grain-oriented electrical Si-Steels (NGOES) and carbide-free bainitic (CFB) steels. The Castrip® process offers a near-net-shape route for producing thin steel strips, which greatly decreases the number of processing stages, lowers energy demand, and reduces carbon dioxide emissions when compared with traditional steel production methods.

In the NGOES part of the study, several industrial Fe–Si steel compositions were cold rolled to final thicknesses ranging from 0.35 mm to 0.15 mm. These materials were then exposed to short-duration continuous annealing at …

Synthesis Of Durable Sio2 Nanoparticle Coatings For Self- Cleaning Solar Panel Surfaces, Pratima Parajuli

Masters Theses

The demand for innovations that improve the efficiency of solar panels has grown due to an increasing reliance on solar energy as a sustainable energy source. Great effort has been made to increase the conversion efficiency of solar energy to electrical energy. The accumulation of dirt, dust, and other environmental particulates on their surfaces is a challenge faced by solar panel technology. These contaminants can significantly reduce the overall performance of the solar panel. Recently, interest in developing self-cleaning surfaces has risen to maintain the performance of solar panels.To create self-cleaning surfaces, silicon dioxide (SiO₂) nanoparticles are emerging …

Assessing A Byproduct Of The Cbd Ethanol Extraction Process For Potential As A Wood Finishing Product, Avani M. Flanagan

Masters Theses

Developments in regulations concerning the use of CBD products as therapeutic remedies have allowed the global cannabidiol (CBD) market to take off within the past five years. Despite producers of CBD oil wanting to optimize their methods and increase product yields, several waste streams still exist. During the winterization phase of the ethanol extraction process, CBD oil is cooled and filtered so the fats, waxes, and lipids from the Cannabis sativa plant can coagulate and be removed, creating a purer oil with higher potency but contributing to the 58% (crude weight) total loss that occurs throughout the process. The removed …

Modeling The Torque Of Ferrite Nano-Particles As A Ferrofluid Suspended In Liquid To Determine The Electromagnetic Response To Angular Displacement, Jackson Tyler Brennecke

Masters Theses

Inertial sensing is an important part of engineering and technology, especially for determining spatial orientation. Most modern inertial sensing units rely on MicroElectroMechanical systems (MEMS) style gyroscopic sensors to determine angular acceleration. This research investigates a novel gyroscopic sensing technology that uses mechanical precision of magnetic nanoparticles, instead of MEMS, to determine inertial measurements. The only other study on this novel technology proposed a scalar set of equations for relating magnetic field and torque magnitude to the magnitude of angular displacement of the sensor. This research develops the theoretical model into a set of full vector equations, so that the …

A Cfd Study On The Performance Of High Speed Planing Hulls, Mowgli J. Crosby

Masters Theses

Most high speed water craft are able to achieve high speeds through the use of a planing hull. Planing hulls use hydrodynamic forces to lift a portion of the vessel out of the water, reducing drag, and allowing for greater speeds. Determining the flow around such vessels is traditionally achieved using a scale model in a tow tank. The purpose of this study was to analyze the performance of a high speed planing hull determine the effects of several geometric features using computational fluid dynamics rather than traditional experimentation. The goal was to determine the best configuration to ensure the …

The Modification Of A Curtain Coating Formulation: A Study Of Rheology And Surface Tension, And Their Effect On Pitting, Samantha Leigh Schoenfelder

Masters Theses

When an undisclosed recycled fiber mill installed a “two-slotted” curtain coater to replace their air knife coater, a prominent defect arose known as “pitting,” which is also called pinholing or cratering. Pitting occurs when the coating of the sheet has small holes that mar its surface, which, when clustered together or larger in size, can cause print breakup during the printing process.

Through research, pitting is known to be caused by a boundary layer of air that gets laterally pulled in between the coating and board during their initial contact. Thus, rheological properties and the surface tension of the curtain …

Satellite Sequencing Optimization And Observational Orbit Determination Using Genetic Algorithms, Andrew W. Verstraete

Masters Theses

The problem of mission design for a robotic servicing satellite in geosynchronous Earth orbit (GEO) was investigated. A representative set of potential client satellites was selected, and operational needs were randomly assigned based on the average number of GEO retirements, anomalies, and repositioning maneuvers that currently occur each year. An objective function was developed to represent the value of servicing mission sequences, including client fees, time penalties, and operational risk. A genetic algorithm was then used to find sequences of operations on the potential client set that maximized the objective function’s value. Scenarios were analyzed with the database of satellites …

Development Of An Effective Portable And Flexible Glove For Hand Tremor Suppression, Abdulrahem Turkistani

Masters Theses

This paper presents the work carried out in designing and developing a prototype for a tremor suppression system that reduces hand tremor by counteracting vibrations initiated from a patient’s shaking hand. This system includes a glove with a built-in vibration simulation module that oscillates and mimics the hand vibration. The oscillation is generated by a DC motor mounted on the top of the glove, and can vary in degree of vibration. The glove is also equipped with an accelerometer-gyroscope based micro-electromechanical system (MEMS) and vibrating coin motors mounted on each finger, both interfaced with a microcontroller. The microcontroller used in …

A Parameterized Implementation Of A Hybrid Fuzzy Boolean Finite State Machine Using An Fpga, Sean T. Fuller

Masters Theses

A fuzzy system based on the extended Hybrid Fuzzy Boolean Finite State Machine (HFBFSM) model is designed and implemented in a Xilinx Zynq® all programmable System on Chip (SoC). The system allows for a single dominant crisp state and multiple non-dominant states to be activated simultaneously. A method is proposed to calculate the degree of membership of non-dominant states, β, by the distance of defuzzified fuzzy inputs to state transition trigger mechanisms.

The HFB-FSM is was realized by the author using custom logic written in VHDL (Very High Speed Integrated Circuit (VHSIC) Hardware Description Language) in the Programmable Logic (PL) …

Mechanics Of Impulse Force Reduction For Mitigating Dump Truck Vibrations Under Hislo Conditions, Danish Ali

Masters Theses

"The deployment of large capacity shovels and dump trucks, for achieving economic bulk production capacities, has resulted in high impact shovel loading operations (HISLO). These large shovels generate high impact forces when loading dump trucks with over 100-ton passes under gravity. The impact forces also generate high frequency shock waves, which cause severe truck vibrations, and thus, expose dump truck operators to high levels of whole body vibrations (WBV). The dynamic impact force generates these vibrations, and thus, there is a need to develop efficient technologies to eliminate or reduce its impact. Existing literature and industry practice show that this …

Simulation Of Drainage Rates Of A Flexible Fiber Network On Wire Screen, Yihsin Tang

Masters Theses

A forming process of a fiber mat over a filter or wire net/screen, which can move horizontally, is numerically simulated. A lattice Boltzmann equation is used to simulate fluid velocity, vorticity and structures and a lattice spring model is employed to mimic the collective motion of up to 750 flexible fibers, with aspect ratio of 20.

The interaction between the fluid and fibers is handled by an immersed boundary method. The fiber motion is driven by the hydrodynamic forces and the gravity of both fluid and solid fibers and disturbed by the horizontal shear force between the fluid and the …

Replacement Of Solvent Based Ink By Water Based Inks For Gravure Presses With Low Efficiency Ink Driers, Viraj Suresh Dalvi

Masters Theses

Rotogravure printing of decorative laminates, wall coverings, or vinyl floorings process often uses solvent based inks. The main constraining factor with solvent based ink is presence of volatile organic compounds (VOC’s). Due to the environmental norms on Volatile Organic Compounds (VOCs), and restrictions on using solvent based inks, the ink industry came up with water based ink as more environmentally friendly alternative. Organizations which print decorative laminates, wall coverings, or vinyl floorings with solvent based inks have gravure printing infrastructure, which is often equipped with low efficiency driers capable of drying solvent based inks. In order to comply with environmental …

Self-Supported Printed Multi-Layer Capacitors, Michael James Joyce

Masters Theses

The increasing demand for miniaturized electronic devices has increased the need for rechargeable micro-power sources. Although lithium and lithium ion batteries have been utilized in these applications since the late 1990s, other energy harvesting technologies, such as thermal, mechanical, and solar, are now being used to augment batteries to enable systems to be self-powered. However, the lifetime of any battery is finite, which may be a major problem when the application is in a permanent structure or medical implant device. For power or significant energy storage applications, printed multilayer capacitors or supercapacitors are being explored as an enhancement, or replacement …

A Novel Silica-Based Nano Pigment As A Titanium Dioxide Replacement, Ryan Stoneburner

Masters Theses

This research focused on the evaluation of a new Silica-based pigment for the replacement of titanium dioxide (TiO₂) in paperboard coatings. The silica-based pigment has shown the ability to be a replacement in terms of functionality and runnability. TiO₂ is currently the highest opacifying pigment used in paper coatings, but it is also the most costly. Finding a less expensive pigment that doesn't reduce effectiveness is critical to reducing the cost of TiO₂ formulations. To evaluate the new pigment, coatings will be applied using a Cylindrical Laboratory Coater (CLC) with varying amounts of TiO₂ and …

Effects On Digital Image Quality When Photographing Through A Transparent Material Used To Hold Or Flatten An Original Object, Paul E. Howell

Masters Theses

An increasing number of libraries and archives are initiating projects where new and updated technologies make it practical to digitize materials containing color and fine detail. Many of the imaging systems and methods used for this process require that some type of glass or plastic be placed over the original to hold it flat and in the correct position during image capture. The physical properties of a material placed between an original object and the capture system or camera, during digitization, could possibly affect the accuracy of image color and quality being reproduced by the system. This investigation provides an …

Oxidation Of Titanium In Alpha-Calf Serum Solution, Ali Stait Ismailoglu

Masters Theses

Titanium and its alloys have been used extensively in orthopedic implants mainly because of its excellent biocompatibility. This biocompatibility is attributed to its surface oxide film (3-7 nm thickness) that forms immediately upon exposure of titanium to air. In the research, the oxidation of Ti-6Al-4V in alpha-calf serum solution was studied. Four different immersion times were tested. Characterization of surface topography and its chemical composition was examined using Atomic force microscopy (AFM), Fourier transform-infrared radiation (FT-IR), and X-ray photoelectron spectroscopy (XPS). The AFM results clearly show the gradual change that occurred in the samples topography which is associated with more-rounded …

Structure And Spectroscopy Of Polymer Ultra Thin Films And Nanocomposites, Ramesh Chandra Kattumenu

Masters Theses

This research involves the study of structure and properties of polymer composite thin films. The intrinsic relation between the morphology and thickness of polymer thin films is the main idea behind this research. Polymer films with thickness in the range of 3nm to 600nm (comparable with the characteristic molecular length scale - radius of gyration) are studied for changes in morphology with temperature and thickness using Atomic Force Microscopy and Raman spectroscopy. The study of very thin polymer films using Force Modulation technique with AFM and Surface Enhanced Raman Spectroscopy showed that polymers could be characterized with these techniques at …

Mechanical Properties And Corrosion Resistance Of Ni-Sic Nano Composite Coatings On 2024-T3 Aluminum, Amit Jain

Masters Theses

Coatings of nickel with and without silicon carbide nano-particles were carried out on 2024-T3 aluminum alloy by the electrochemical process. The size of the silicon carbide particles was less than 50nm. Nickel coatings were done using a nickel sulfamate bath maintained at a constant temperature of 50° ± 5° C. Tensile specimens were prepared and studied to determine the Young's modulus of bare aluminum, with nickel coatings and with composite nickel and silicon carbide coatings. Wear samples of 1 inch² (6.45cm²) were prepared and studied for wear resistance. The residual stress measurements were done by the hole …

Structural Studies Of Metastable Nanocrystalline Magnesium Titanate Ceramics, Renmei Xu

Masters Theses

Nanocrystalline magnesium titanate powders were produced using alkoxides of magnesium and titanium for the sol-gel method. High temperature phases which can only be formed at above 1200°C in equilibrium were formed at much lower temperature 600°C in nanometric system. Cation ordering and structural changes in qandilite (Mg₂TiO₄ ), geikielite (MgTiO₃ ) and karrooite (MgTi₂O₅ ) were studied by Rietveld refinement of neutron powder diffraction data and X-ray photoelectron spectroscopy. Single qandilite phases were obtained in a wide range of Mg:Ti ratios from 2:038:1 to 1.52:1, and appeared to be Mg_2-xTi_{1+x …}

An Investigation Of Mechanical Properties Of Composites Containing Recycled Rubber Particles, Ryan C. Archey

Masters Theses

In order to promote applications of recycled automobile tires, composite materials of recycled rubber tire particles with ethylene co-vinyl acetate (EVA), polybutadiene (PB), and Primacor were studied in the thesis. The composites were processed using a single screw extruder and a pelletizer. Compression molding was used to form specimens for hardness and impact tests. Mechanical properties of the composites were investigated in terms of tensile strength, percent elongation, Durometer hardness, and impact energy.

In this study, the content of recycled rubber was between 0 and 40 percent. Various matrices were processed using a combination of EVA, PB, or Primacor to …

Eigenproperties Of Nonclassically Damped Dynamic Systems, Daniel Patrick Malone

Masters Theses

"This thesis develops perturbation series solutions for the eigenvalues and eigenvectors of nonclassically damped dynamic systems for the case where the unperturbed system has repeated eigenvalues. The case of repeated eigenvalues is much more complicated than the case of perturbing a system with distinct eigenvalues. Because of this difficulty, only a specific category of dynamic systems with repeated eigenvalues is addressed. Namely, only those systems that when perturbed have series solutions of the form of a power series. This category of systems can be easily identified by an a priori check developed in the application section of this thesis. The …

Nonlinear Finite Element Micromechanic Analysis Of Thermoplastic Composite Of Recycled High Density Polyethylene Reinforced With Short Glass Fibers, Qiming Lou

Masters Theses

This thesis studied the nonlinear micromechanic behavior of thermoplastic composite of recycled high density polyethylene (HDPE) reinforced with short glass fibers using finite element method. The composite material was modeled using a micromechanic unit cell to simulate the stress distribution between the plastic matrix and the fiber in the composite. Nonlinear behavior of recycled HDPE and imperfect bonding between the fiber and matrix were investigated. Load-bearing capability of the fiber was evaluated using stress partition ratio (SPR) in the composite models. The effect of fiber aspect ratio on the stress distribution of the composite was studied to optimize the material …

A Study Of The Effects Of Polyacrylates On Water Retention And Binder Migration Tendencies Of Coatings, Wichan Charoenkitsupat

Masters Theses

Five commercial polyacrylate samples were used to study their effects on viscosity, water holding, and binder migration under non-pressure conditions. The polyacrylates used were different in acid level, degree of crosslinking, and type of polymer (copolymer and terpolymer). A series of coatings was prepared using a number two clay and three styrene-butadiene latexes of similar particle size and T⋁g but different degrees of carboxylation, then the polyacrylates were added at several levels. The coatings were evaluated for rheological properties, water loss rate and binder migration. The results show that with increasing amounts of polyacrylates, the viscosity increased and the water …

Development Of A Quadratic Finite Element Solution Of The Convective-Transport Equation., David A. Dillard

Masters Theses

"A quadratic finite element has been developed for the solution of the general three-dimensional convective-transport equation. Inherent instabilities in the numerical solution arise when the convective terms in the governing equation become significant. An application of upwinding techniques to the 20 degree of freedom serendipity element failed to produce acceptable results. Upwinding was applied to the 27 degree of freedom Lagrangian element with good results. Results of the latter element are given for several problems, including a model of a round to round metal forming process"--Abstract p. iii

Deformation Of A System Of Clamped Thin Circular Plates With Liquid Filled Interspace., Archie Forrest Gatrost

Masters Theses

"In this work the behavior of a system of thin, circular clamped plates with liquid-filled interspace in a variable pressure environment was investigated. Six plates separated by liquid-filled chambers were arranged in alternate layers in a clamping device and a pressure was applied on one side of the six plate system. The deformation of each plate and the pressure distribution from the high pressure to low i i pressure side was measured. The plate deformation was measured by a strain gage attached at the apex of each plate and the chamber pressure by a strain gage pressure transducer.

The results …

Stability Of Filled Cylindrical Shell Columns, Yu Wen Tsao

Masters Theses

"This experimental investigation was conducted to study the stability of filled cylindrical shell columns. Two kinds of filler materials, flower clay (florist clay) and silica sand, were investigated. The cylindrical shells were made of 2024-T3 Reynolds aluminum tubing. Uniaxial compressive loading was applied directly to the filler materials through two loading rams, one at each end of the cylinder, (no loading was applied directly to the shell). Tests for investigating the load transmitting characteristics of the filler materials were performed, and the states of the stresses existing in the cylindrical shells were then obtained.

The buckling formula for thin-walled cylindrical …

Investigation Of An Energy Absorbing Device For Passenger Safety, Prakash Krishnaswamy

Masters Theses

"Energy absorption by driving an oversized plunger through a longitudinally slit shell has been studied. The characteristics obtained by conducting several runs indicate that such a system could be used for energy absorption and for limiting the force required to drive the plunger through the shell. The characteristics can be readily altered by changing the dimensions of the tube. Details of the experimental set-up have been given.

Such an absorber has been adapted for mitigating injury sustained by the occupants in the interior of a colliding vehicle. Full advantage has been taken of the "Ride down" potential available to the …

A Comparison Of Analytical And Experimental Approaches In Determining The Thermoelastic Stresses Around A Cylindrical Inclusion Of Elliptical Cross-Section, Kenneth Byron Oster

Masters Theses

"Three approaches are used to determine the principal stress differences in an infinite elastic medium containing a cylindrical inclusion of elliptic cross-section due to a uniform temperature change. First, the two-dimensional equations of thermoelasticity are solved resulting in equations for the stress components anywhere in the medium material. Second, boundary displacements based on stress-strain relations are used as input displacements in a finite element program of the medium. Third, these same boundary displacements are used as input displacements on a photoelastic model simulating the medium. The problem is treated as one of plane strain in the first approach and one …

The Analysis Of An Axially Symmetric Submerged Membrane Shell, Walter Earl Wehmeyer

Masters Theses

"The general theory of large elastic deformations is applied to the problem of a liquid-filled, axisymmetric membrane which is supported on a rigid horizontal plane and subjected to a variable external pressure. The variable external pressure is caused by submerging the membrane to various depths. The variation of the hydrostatic pressure in the inflating medium as well as in the surrounding environment is considered. By assuming large meridional deformations the stress field and the deformed shapes of a submerged membrane made of a neo-Hookean material are obtained. The effect of the initial shape on the deformed configuration of the membrane …

A Study Of The Effect Of Drilled Holes On The Concentration Of Elastic Stresses Around A Notch, Glenn Michael Kmecz

Masters Theses

"Hole drilling as a method for improving the toughness of notch weakened tensile specimens is investigated by means of a photoelastic technique. Tests were performed on 20%, 40%, 60%, and 80% notch depth specimens machined from PSM-1 photoelastic material. The basic criteria for success was no increase in the elastic stress concentration factor. The photoelastic results were verified by a finite element stress analysis of the 60% notch depth specimens. Comparison of the experimental and numerical results provide conclusive proof that no increase in the elastic stress concentration factor occurs when proper positioning of the drilled holes is accomplished"--Abstract, page …