Engineering Education Commons^™

Effect Of Rheology Modification On Fiber Orientation And Dispersion In 3d-Printed Ultra-High-Performance Concrete, Haodao Li, Alfred Addai-Nimoh, Seongho Han, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The extrusion process in 3D concrete printing (3DCP) facilitates horizontal alignment of steel fibers along the printing direction, thus enhancing the load-bearing capacity of printed elements. However, such shear-induced fiber alignment is highly sensitive to rheological properties. This study investigates how variations in dynamic yield stress (τd) and plastic viscosity (μ), influence the extrudability, fiber orientation and dispersion, and anisotropic mechanical behavior of ultra-high-performance concrete (UHPC). Five viscosity-modifying agent (VMA) types were incorporated at two content levels to modify the rheology of printable UHPC. Results showed that moderate VMA additions improved printability, whereas excessive contents markedly increased τd and μ; …

How Does Competitive Adsorption Between Vma And Pce Influence Yield Stress Of Cement Paste? A Novel Insight From Interparticle Forces And Percolation Threshold, Huamin Sun, Le Teng, Xiaohan Yu, Xin Shu, Zhangli Hu, Jiaping Liu, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Viscosity modifying admixture (VMA) and polycarboxylate superplasticizer (PCE) are often combined to optimize rheological properties of cement-based materials. However, the competitive adsorption of these complex admixtures can greatly influence rheological properties. Many studies have investigated the variation of yield stress due to competitive adsorption between VMA and PCE; but the mechanisms are not fully understood. This study aims to shed a new light on this question in cement paste systems prepared with low water-to-binder ratios of 0.16–0.30. The competitive adsorption of VMA and PCE was quantitatively assessed using the Total Organic Carbon and Ultraviolet-Visible Spectroscopy measurements. The effect of competitive …

Transforming Dredged Sediment Into Reactive Clay: Critical Review Of Calcination, Reactivity, And Sustainable Valorization As Supplementary Cementitious Material, Seongho Han, Sanghwon Wi, Koochul Ji, Keun Hyeok Yang, Farshad Rajabipour, Kamal H. Khayat, Jinyoung Yoon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Dredged sediment (DS) is generated worldwide in large volumes through routine port and waterway maintenance, yet its disposal presents environmental and economic challenges. Recently, calcined dredged sediment (CDS) has emerged as a supplementary cementitious material (SCM), offering a viable alternative to traditional SCMs, such as fly ash and slag cement. This review synthesizes current knowledge on the physical, chemical, and mineralogical characteristics of raw DS and pretreatment strategies aimed at dewatering, organic matter removal, and contaminant stabilization. The effects of calcination on the production of reactive amorphous aluminosilicates are also discussed. Emphasis is placed on physicochemical changes revealed by experimental …

Low-Carbon Concrete For Sustainable Construction: A Comprehensive Review Of Performance Characteristics, Implementation Challenges, And Decarbonization Pathways, Fazel Azarhomayun, Jingjie Wei, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Reducing the carbon footprint of concrete has become a central objective in sustainable construction. Low-carbon concrete (LCC), developed primarily through clinker reduction, supplementary cementitious materials, and alternative binder strategies, offers a promising route for lowering embodied emissions while maintaining the performance requirements of structural concrete. This comprehensive review consolidates the current state of knowledge on LCC, identifies critical research and implementation gaps, and examines its material composition, mixture-design methodologies, performance characteristics, structural applications, implementation challenges, and decarbonization pathways. Single-SCM systems have been reported at clinker-replacement levels approaching 50%, although durability at these replacement levels, particularly carbonation resistance, remains system- and …

Recent Advances In The Rheological Properties Of Ultra-High-Performance Concrete: A Critical Review, Le Teng, Kamal H. Khayat, Jiaping Liu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Ultra-high-performance concrete (UHPC) with adapted rheology continues to attract interest considering the requirement for novel processing techniques such as self-consolidating, pumping, spraying, and three-dimensional (3D) printing. The rheology of UHPC is complex due to its high solid volume fraction, low water content, and wide range of constituent materials that affect its flow properties. This work provides guidance for tailoring the mixture proportioning of UHPC to secure proper rheological properties and performance of UHPC for various applications. In the first part of this work, key physical, physicochemical, and chemical factors that can affect the rheological properties of UHPC are discussed. Rheological …

Computer Vision And Machine Learning Approaches For Defect Detection In 3d-Printed Cementitious Materials: A Systematic Review, Muhammad Ali Musarat, Ruben Paul Borg, Jingjie Wei, Carl James Debono, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

3D printing is evolving at a fast pace in both the manufacturing and construction sectors. These advancements can greatly benefit these industries. However, the 3D printing of concrete structures presents some challenges due to defects in the 3D concrete printed elements. Hence, this study systematically reviews Artificial Intelligence (AI)-driven techniques, such as Computer Vision and Machine Learning, to identify surface defects that can occur in 3D-printed cementitious material structures. The adopted methodology was the PRISMA statement with the aim of reporting the systematic review and meta-analysis. Two well-known databases, Web of Science and Scopus, were utilised for data extraction of …

Toward Sustainable 3d Printable Cementitious Materials: Low-Carbon Design With Fiber Reinforcement, Nima Mahmoudzadeh Vaziri

Miners Solving for Tomorrow Research Conference

3D printing of cementitious materials, as an emerging construction technology, faces challenges in both mechanical performance and sustainability. Conventional mixture designs rely on high cement contents, leading to increased CO2 emissions, while printed elements often exhibit brittle behavior with limited crack resistance and reduced post-cracking performance. This study investigates the development of low-carbon 3D printed cementitious composites using environmentally friendly supplementary cementitious materials (SCMs) and fillers, combined with fiber reinforcement to enhance mechanical performance. Locally available SCMs and fillers were incorporated to significantly reduce cement content (>40%) and improve sustainability. Fiber reinforcement was introduced to mitigate brittleness and enhance …

New Insights Into Dynamic Evolution Of Colloidal Network Structure During Early-Age Hardening Of Cementitious Materials, Hengrui Liu, Kaiyin Zhao, Shipeng Zhang, Hanghua Zhang, Shuangshuang Liu, Lucen Hao, Hongyan Ma, Kamal Khayat, Chi Sun Poon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The evolution of microstructure in cementitious materials during their transition from fluid to solid state plays a critical role in determining their ultimate mechanical strength and overall performance. This hydration stage primarily involves a dynamic densification process occurring within the colloidal network. However, the field of cement-based materials currently lacks a comprehensive theoretical framework and associated parameters capable of effectively characterizing the specific structural regions within this network. In this study, we propose an Improved Particle Linkage (IPL) theory for describing the strength, types, and quantities of particle linkages within colloidal network. The IPL theory classifies the internal network structure …

Advances And Challenges In Nano-Modified Cementitious Composites: Mechanisms, Dispersion Strategies, And Impact On Mechanical Properties, Fatemeh Mohammadi Ghahsareh, Pengwei Guo, Nusrath Jaha, Yi Bao, Kamal H. Khayat, Weina Meng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Nanomaterials are increasingly utilized to enhance the mechanical properties, durability, and functionality of concrete materials but face challenges such as agglomeration and uneven dispersion in cementitious systems, which can offset the intended improvements. This paper reviews the advances and challenges associated with nano-modified cementitious composites, elucidating fundamental mechanisms and highlighting strategies for overcoming the challenges through experimental and computing techniques. The reviewed contents include (1) the classification of nanomaterials commonly used in cementitious systems and the mechanisms through which they enhance the mechanical properties of cementitious composites; (2) challenges of nanomaterials such as agglomeration in water, re-agglomeration in cementitious systems, …

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Co2-Induced Changes In Rheology, Structural Evolution, And Particle Characteristics Of Cement Paste, Seongho Han, Tae Yong Shin, Seung Mo Kim, Jae Hong Kim, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The injection of carbon dioxide (CO₂) into cementitious systems has emerged as a promising approach to enhancing sustainability in concrete production. This study explores the impact of CO₂ injection on the rheological behavior, structural build-up, and particle size evolution of cement paste by systematically varying the water-to-cement ratio (w/c) (0.35, 0.4, and 0.5) and CO₂ concentration (0.06, 0.28, and 0.84 mol). Rheological analysis revealed a significant increase in initial yield stress with CO₂ injection. Using the Modified Bingham model, yield stress increased by 72 % and 150 % for 0.28- and 0.84-mol CO₂, …

Influence Of Mixing Duration And Absorption Characteristics Of Superabsorbent Polymers On The Fresh And Hardened Properties Of High-Performance Concrete, Yu Cun Gu, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigates the combined influence of superabsorbent polymers (SAPs) with distinct absorption kinetics and extended mixing sequences on the rheological, mechanical, and transport properties of high-performance concrete (HPC). Two SAPs—an ionic acrylamide-co-acrylic acid copolymer (SAP-P) and a non-ionic acrylamide polymer (SAP-B)—were incorporated at an internal curing level of 100%. The impact of extended mixing times (3, 5, and 7 min) following SAP addition was systematically evaluated. Results showed that longer mixing durations led to increased superplasticizer demand and higher plastic viscosity due to continued water absorption by SAPs. However, yield stress remained relatively stable owing to the dispersing effect …

Modeling And Estimation Of Co2 Capture By Porous Liquids Through Machine Learning, Farid Amirkhani, Amir Dashti, Hossein Abedsoltan, Amir H. Mohammadi, John L. Zhou, Ali Altaee

Chemical and Biochemical Engineering Faculty Research & Creative Works

Porous liquids (PLs) are newly developed porous materials that combine unique fluidity with permanent porosity, which exhibit promising functionalities. They have shown ability to efficiently absorb greenhouse gases such as carbon dioxide (CO₂). Experimental measurement is one approach to determining the solubility of various greenhouse gases in PLs, which has drawbacks such as being expensive and time-consuming. Hence, simulation models are valuable to predict the solubility of CO₂ in various PLs. This work aims to develop machine learning (ML) modeling methods for accurately estimating CO₂ solubility under varying conditions (e.g. PLs, temperature, pressure). Adaptive Neuro-Fuzzy Inference …

Treatment And Activation Effects On Kaolinite-Based Earth Concrete, Mojtaba Kohandelnia, Maroua Zerzouri, Ammar Yahia, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Self-consolidating earth concrete (SCEC) addresses the long construction process of conventional earthen constructions and their structural limitations, while further efforts are needed to enhance its sustainability. This study explores the development of a kaolinite-based self-consolidating earth paste (SCEP) due to their blended powder system, incorporating raw and treated (calcined and ground-calcined) kaolinite under various activation techniques, such as water hydration, sodium hexametaphosphate (NaHMP), and sodium hydroxide (NaOH) activation. The synergistic effect of calcination and mechanosynthesis on rheological, mechanical, structural, and microstructural properties of SCEP were investigated. Mechanically treated kaolinite increased yield stress, plastic viscosity, storage modulus evolution, and build-up index, …

Underlying Mechanisms Of The Effect Of Microfines Of Manufactured Sand On Non-Linear Structural Build-Up Of Cement Paste, Jiang Zhu, Jiaping Liu, Kamal H. Khayat, Xin Cheng, Wei Zhao, Zhen Li, Xin Shu, Yongbo Huang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The rheological properties of cement-based materials made with manufactured sand vary with the content and physio-chemical properties of microfines in the sand. However, the evaluation of rheological properties regarding the structural build-up at early-age hydration remains challenging for the cementitious materials prepared with different manufactured sands, due to complicated underlying structuration mechanisms. This paper studies the effect of disparate microfines of different manufactured sands on the non-linear growth of static yield stress of cement pastes at rest. The paste mixtures were prepared with 0.40 and 0.275 water-to-cement mass ratio (W/C) and had a fixed mini-slump flow of 240 ± 5 …

Enhancing Road Performance With Void Reducing Asphalt Membrane, Tim Zahrn, Todd Thomas, Randy Miller

Purdue Road School

This presentation will discuss how using the technology of a Void Reducing Asphalt membrane can improve performance of our Asphalt Pavements by creating a more durable asphalt surface that resists cracking and reduces permeability. Void Reducing Asphalt Membrane (VRAM) Specifications: VRAM reduces voids in longitudinal joints, which improves the longevity of a quality road surface. INDOT has already required VRAM on certain road designs. We will review the current specifications for VRAM and outline specifications that may update with the technology. We will also discuss the Impact of Rumble Strips on Longitudinal Joint Performance. The session will also highlight how …

Effect Of Shrinkage-Mitigating Materials, Fiber Type, And Repair Thickness On Flexural Behavior Of Beams Repaired With Fiber-Reinforced Self-Consolidating Concrete, Jingjie Wei, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

While self-consolidating concrete (SCC) has emerged as a highly effective approach for the repair of concrete structures, there have been few investigations regarding the effect of the combination of different fiber and shrinkage-mitigating material types (shrinkage-reducing admixture, SRA; superabsorbent polymer, SAP; and expansive agent, EA) on the flexural behavior of repaired structures. This study aims to explore the influence of three different shrinkage-mitigating materials (1.25%–2.5 % SRA, 4%–8% EA, and 0.2%–0.4 % SAP), four fiber types (two macro synthetic fibers, MSFA and MSFB; 5D hooked steel fibers, 5D; a combination of 80 % 3D hooked steel +20 % short steel …

Flexural Post-Cracking Performance Of Macro Synthetic Fiber Reinforced Super Workable Concrete Influenced By Shrinkage-Reducing Admixture, Jingjie Wei, Nima Farzadnia, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Most literature has focused on the effect of shrinkage-reducing admixture (SRA) in shrinkage mitigation resistance of concrete. This study aims to examine the impact of SRA on the efficiency of macro synthetic fibers (MSF) in enhancing the flexural post-cracking behavior of fiber-reinforced super workable concrete (FR-SWC). A comparative analysis of the influence of fiber combinations on the flexural post-cracking behavior of beams is also included. Results showed that a higher dosage of SRA, particularly at 5 % by mass of binder, had a noticeable negative impact on flexural post-cracking performance of beams while exhibiting positive effect on workability and shrinkage …

Machine Learning Modeling For Hydrolysis Recycling Of Pet Waste, Jie Li, Lanjia Pan, Hossein Abedsoltan, Hailong Wang, Taiyang Liu, Xiangzhou Yuan, Yong Sik Ok, Yin Wang

Chemical and Biochemical Engineering Faculty Research & Creative Works

The hydrolysis of polyethylene terephthalate (PET) into terephthalic acid (TPA) can efficiently recycle waste PET, but achieving high conversion efficiency through smart reaction design remains challenging. To develop a robust and accurate machine learning (ML) model for the in-depth understanding and intelligent design of PET hydrolysis, we compiled a new dataset comprising 942 data points and comprehensive information of 44 variables involved in heating type, acid/base catalyst (ABC), organic solvent (OS), co-solvent (CS), phase transfer catalyst (PTC), and operational conditions. The developed Neural Network model demonstrated the best performance in predicting PET conversion, with a testing determination coefficient (R^{2 …}

Transitioning To A Lower Global Warming Refrigerant, A Performance Study Of R-513a And Hfc-134a In Commercial Chillers, Hossein Abedsoltan, Mark B. Shiflett

Chemical and Biochemical Engineering Faculty Research & Creative Works

The performance of R-513A and HFC-134a refrigerants is compared in two identical chillers operating at the University of Kansas. R-513A is a more environmentally friendly refrigerant due to its lower global warming potential that can be used as a retrofit replacement for HFC-134a in chillers. This study investigates the performance comparison of transitioning from HFC-134a to R-513A. The chillers have been in operation for two years, and cooling capacity, coefficient of performance, and other operating parameters are compared under similar cooling conditions. Cooling capacities ranged from 100 to 500 kW for both chillers. Overall, the energy consumption and coefficient of …

The Effects Of Engineering Summer Camps On Middle And High School Students’ Engineering Interest And Identity Formation: A Multi-Methods Study, Timothy Robinson, Adam Kirn, Jenny Amos, Indira Chatterjee

Journal of Pre-College Engineering Education Research (J-PEER)

This multi-methods study explores changes in engineering interest and identity of middle and high school students (n = 79) attending introductory-level engineering summer camps at a large western land grant university. Middle school is a critical time when student interest, identity, and subsequently career choice begin to emerge and hence it is important that at this age students are given accurate information about engineering majors in college and future career opportunities in engineering. Data were collected over a period of two years in six summer camps. Three separate populations of middle and high school students participated in the summer …

The Plastics Collection Reference Packet, Special Collections Research Center

Special Collections Research Center

This reference packet is an informational tool to support further research into the history of plastics—whether interested in companies, individuals within the plastics industry's history, historical plastics materials, essays, and more. All content featured within this packet was previously published on the former plastics.syr.edu website as part of a Syracuse University Libraries and Special Collections Research Center (SCRC) partnership established in 2007 with the Plastics Pioneers Association (PPA)—an association of plastics industry professionals interested in preserving the plastics industry's past.

Could The Inclusion Of Certain Building Information And Modelling Aspects Into The Leaving Certificate Engineering Syllabus, Aid The Transition Of Students Into Third Level Education, When Choosing A Course Within The Construction Industry, Joseph Boyle, Deborah M. Brennan

Capstone Reports

The paper investigates the effects of implementing several Building Information and Modelling (BIM) aspects into the Leaving Certificate Engineering Syllabus and examines the impact this has on students choosing third level Architectural Engineering and Construction (AEC) industry courses with the desire of improving the shortage in the sector. The method and content of the study was based on academic research on second level education in other European countries through the lens of a Literature Review. A sixteen-week pilot program was trialed with over one hundred students at Senior Cycle. The outcomes of the study were critically evaluated through stakeholder interviews …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …

Augmented Reality Integrated Welder Training For Mechanical Engineering Technology, Aditya Akundi, Hamid Eisazadeh, Mona Torabizadeh

Engineering Technology Faculty Publications

The shortage of welders is well documented and projected to become more severe for various industries such as shipbuilding in coming years. It is mainly because welding training is a critical and often costly endeavor. This study examines the training potential using augmented reality technology as a critical part of welder training for mechanical engineering technology students. This study assessed the performance of two groups of MET students trained with two different methods. One group received training with the traditional method in three sessions. The second group acquired training initially with an augmented reality welding system for three sessions. Then, …

Development Of An Undergraduate Welding Laboratory For Research And Education, Hamid Eisazadeh, Alok K. Verma

Engineering Technology Faculty Publications

The shortage of welders in Hampton Roads area, where many shipyards are located, is becoming severe for shipbuilding in coming years. Many welding engineers graduated from universities located out of state, tend to go back to companies near their home, after receiving couple years of welding experience at Hampton Roads shipyards. Therefore, it is critical to train local welders. In order to address the welding workforce needs of Hampton Roads, the Department of Engineering Technology at Old Dominion University has recently launched an initiative for developing a laboratory for welding processes (LWP) for supporting educational and research activities in its …

A Brief Bibliometric Survey On Circularly Polarized Antennas For Mobile Communication, Aniket Gunjal, Abhaya Pal Singh

Library Philosophy and Practice (e-journal)

This paper presents a database review on “Circularly Polarized Antennas for Mobile Communication” as it is the emerging technique used by mobile service provider because of having benefits over other types of antennas available.The polarization purity is now the major issue. In some cases due to cross polarization issue the antenna signal is cancelled at receiver side.So, it is necessary to have circularly polarized antenna to avoid this polarization issue because of change in phase of signal. The change in phase of signal is due to striking of wave on the obstacles and it slightly tilted from its direction causes …

Integrating Professional Skills And Leadership Into An Undergraduate Engineering Program, Harold Ackler, Heidi Reeder, Abbey Louie

Materials Science and Engineering Faculty Publications and Presentations

Research and practical experience indicate that leadership and “people skills” play an important role in the success of organizations and in the careers of employees across many industries, including engineering. The Micron School of Materials Science and Engineering at Boise State University identified a need to expand available opportunities for its students to develop these critical “soft” skills. The approach taken sought to imitate how such training is conducted in the workplace, integrating it within a context of extended team-based projects. In partnership with the College of Innovation + Design’s Leadership Certificate Program, a series of sequential modules were developed …

Correction To: Recommendations Of Rilem Tc 260-Rsc For Using Superabsorbent Polymers (Sap) For Improving Freeze–Thaw Resistance Of Cement-Based Materials (Materials And Structures, (2019), 52, 4, (75), 10.1617/S11527-019-1375-4), Viktor Mechtcherine, Christof Schröfl, Michaela Reichardt, Agnieszka J. Klemm, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Agnieszka J. Klemm is affiliated to Glasgow Caledonian University, Glasgow, UK.