Systems and Communications Commons^™

Ism-Band Energy Harvesting Wireless Sensor Node, Fnu Naveed

Graduate Theses and Dissertations

In recent years, the interest in remote wireless sensor networks has grown significantly, particularly with the rapid advancements in Internet of Things (IoT) technology. These networks find diverse applications, from inventory tracking to environmental monitoring. In remote areas where grid access is unavailable, wireless sensors are commonly powered by batteries, which imposes a constraint on their lifespan. However, with the emergence of wireless energy harvesting technologies, there is a transformative potential in addressing the power challenges faced by these sensors. By harnessing energy from the surrounding environment, such as solar, thermal, vibrational, or RF sources, these sensors can potentially operate …

A Modular Framework For Surface-Embedded Actuation And Optical Sensing In Soft Robots., Paul Bupe Jr

Electronic Theses and Dissertations

This dissertation explores the development and integration of modular technologies in soft robotics, with a focus on the OptiGap sensor system. OptiGap serves as a simple, flexible, cost-effective solution for real-time sensing of bending and deformation, validated through simulation and experimentation. Working as part of an emerging category of soft robotics called Soft, Curved, Reconfigurable, Anisotropic Mechanisms, or SCRAMs, this research also introduces the Thermally-Activated SCRAM Limb (TASL) technology, which employs shape-memory alloy (SMA) wire embedded in curved sheets for surface actuation and served as the initial inspiration for OptiGap. In addition, the EneGate system is presented as a complementary …

Project Thetis: A Low-Cost, Low-Profile Inertial Data Logger, Braidan Duffy

Theses and Dissertations

This thesis details the design, testing, calibration, and verification of a nine degree of freedom inertial measurement data logger for use with floating bodies. The instrument was conceived to address limitations of equipment used in classes within the Ocean Engineering department at Florida Institute of Technology. By meeting with several stakeholders and end users, a series of stakeholder requirements, capabilities, and component-level requirements were de- veloped that informed the design constraints. There were several hardware iterations of the board, culminating in Revision F5 which was extensively tested and proven. The design was inspected after testing concluded to determine which capabilities …

Instrumented Control Column For Optionally Piloted Aircraft, Andrew J. Klein

Electrical Engineering

Natilus, an aerospace company that is rapid-prototyping optionally piloted aircraft (OPA) for the shipping industry, needs a system that retrieves control column position data in order to manipulate flight simulator parameters in software. At present, a universally compatible system for all aircraft does not exist. Typically, established aerospace companies will sink significant time and money into developing proprietary systems for control column data retrieval as every aircraft is unique in its layout and linkage design. However, as a startup developing their first aircraft, Natilus does not have the privilege of modifying an existing sensor system to work with their HIL …

Designing The Power System Of A Robot, Nolan Hays

Honors College Theses

This thesis outlines the acquired skills and knowledge acquired through the course of four years of Murray State University’s School of Engineering. The capstone for students in the department was to team up and complete an interdisciplinary senior design project using skills from various tracks of engineering. For this thesis, there is a greater emphasis on the electrical engineering track. The objective of the project was to build an autonomous robot to complete the various tasks within the scope of the IEEE SoutheastCon 2023 Hardware Competition. The robot was controlled via a Raspberry Pi 4 Model B. There were three …

Assessing The Performance Of A Particle Swarm Optimization Mobility Algorithm In A Hybrid Wi-Fi/Lora Flying Ad Hoc Network, William David Paredes

UNF Graduate Theses and Dissertations

Research on Flying Ad-Hoc Networks (FANETs) has increased due to the availability of Unmanned Aerial Vehicles (UAVs) and the electronic components that control and connect them. Many applications, such as 3D mapping, construction inspection, or emergency response operations could benefit from an application and adaptation of swarm intelligence-based deployments of multiple UAVs. Such groups of cooperating UAVs, through the use of local rules, could be seen as network nodes establishing an ad-hoc network for communication purposes.

One FANET application is to provide communication coverage over an area where communication infrastructure is unavailable. A crucial part of a FANET implementation is …

Predicting Jamming Systems Frequency Hopping Sequences Using Artificial Neural Networks, Charles Strickland

Electronic Theses and Dissertations

This work proposes a neural network architecture that was designed to predict and reverse engineer frequency hopping jamming systems. The neural network was initially optimized for use with a 12th order linear shift feedback register maximum length sequence utilizing a minimal polynomial as the characteristic polynomial. This neural network was then scaled to accommodate 7 different sequences, of orders 6 through 12. The neural network was trained for these sequences using training data that is 10 times the length of the sequence. This information is then used to generate a hopping sequence that reduces the jamming interference to 0 with …

Wireless Kick Pedal, Jacob Wise, Ryan Kinyo, Bradley Toth, Ian Zanath

Williams Honors College, Honors Research Projects

The goal of the project is to build a wireless kick pedal that allows accessibility to drummers that have leg or foot disabilities and add versatility to multi-instrumentalists looking to add percussion while playing another instrument. The proposed pedal is designed in two main parts, a wearable band that tracks the player’s movement, and a hammer mechanism that receives actuation commands from the wearable band to move the hammer and deliver a drumbeat. The band is designed to be worn on several parts of the body, including the ankle, knee, thigh, or even the arm depending on the user’s situation. …

Whiteboard Drawing Device, Stefan Ilic, Andrew Adams, Vaughn Richards, James Medved

Williams Honors College, Honors Research Projects

Whiteboards have become a staple in many classrooms, especially in the context of STEM courses. However, when it comes to teaching complex topics, it can be difficult or impractical to provide accurate drawings and visualizations by hand, and in extreme cases may lead to misinterpretation of a particular topic. To fix this issue, the Whiteboard Drawing Device allows users to draw preset shapes to a whiteboard automatically, both quickly and accurately. Using either a smartphone application or a set of onboard controls, the device allows users to automatically draw straight lines, rectangles, triangles, sinusoidal waves, and circles on the whiteboard. …

Wireless Environmental Weather Monitor, Joel Christie-Millett, Nathan Schroeder, Sylvester Wilson, Matthew Szijarto

Williams Honors College, Honors Research Projects

The goal of this senior design/honors project is to create a device that monitors environmental conditions in order to detect a wildfire. This device should notify a user of the status of the environment. The device should also last for 6 months without any human interaction. My role on the team is to design the power supply system that maximizes efficiency and uses renewable energy.

Wifi Sensing At The Edge Towards Scalable On-Device Wireless Sensing Systems, Steven M. Hernandez

Theses and Dissertations

WiFi sensing offers a powerful method for tracking physical activities using the radio-frequency signals already found throughout our homes and offices. This novel sensing modality offers continuous and non-intrusive activity tracking since sensing can be performed (i) without requiring wearable sensors, (ii) outside the line-of-sight, and even (iii) through the wall. Furthermore, WiFi has become a ubiquitous technology in our computers, our smartphones, and even in low-cost Internet of Things devices. In this work, we consider how the ubiquity of these low-cost WiFi devices offer an unparalleled opportunity for improving the scalability of wireless sensing systems. Thus far, WiFi sensing …