Modeling And Simulation Of Solar Battery Charge Controller Using Adaptive Particle Swarm Optimization Mppt Algorithm, Mustafa Sacid Endiz, Göksel Gökkus

Mathematical Modelling and Numerical Simulation with Applications

Implementing an effective Maximum Power Point Tracking method is crucial for optimizing solar energy harvesting against environmental fluctuations like solar radiation and temperature. This paper introduces a novel approach for modeling and simulating a solar battery charge controller, using a modified Particle Swarm Optimization algorithm. The power stage of the system is based on a SEPIC converter, which is employed to manage the power conversion and improve the energy transfer to the battery. The developed circuit model is evaluated under various radiation levels at a constant temperature, as well as under different temperature levels at a constant radiation. Simulations are …

Analytical And Semi-Analytical Modeling Of Solar Cells Using The Lambert W Function: A Comprehensive Review Of Equivalent Circuits, Adel El-Shahat, Martin Ćalasan, Snežana Vujoševic, Shady H. E. Abdel Aleem

Engineering Technology Faculty Publications

The modeling of photovoltaic (PV) cells through equivalent circuits forms a central element in the analysis, simulation, and optimization of solar energy systems. Traditional approaches often depend on iterative numerical methods to solve the implicit current–voltage (I–V) equations. In contrast, the Lambert W function has emerged as an effective mathematical tool that enables closed-form or semi-analytical expressions for a wide range of PV models. This paper presents a Lambert W-centered review of analytical and semi-analytical formulations for PV equivalent-circuit models, covering classical single-diode and multi-diode structures and modern variants incorporating additional elements, voltage-dependent parameters, and topology rearrangements. The models are …

End-To-End Direct Current For Standalone Power Network, Eyad Ahmad Aldarsi

All Dissertations

The primary issue that faces the humanity is climate change and because of that greenhouse gases (GHGs) emissions are rising. The consequences of this issue have emphasized the necessity for replacing the dominant method of electricity generation, which mostly utilizes fossil fuels, to be centered on access to all, green, low-cost, and renewable sources of energy. Currently, photovoltaics (PV) and wind turbines are the two technologies so far that can convert the source of renewable energy, which is produced by sun irradiance and wind respectively, into large-scale electric power that can be distributed into the electricity grid. The work in …

Design And Performance Evaluation Of Pv-Powered Ev Charging Stations With Grid Integration And Comparative Analysis Of Dc-Dc Converters For Offboard Chargers, Mohammad Abidur Rahman

Theses and Dissertations

Grid-integrated photovoltaic (PV)-powered electric vehicle (EV) charging stations offer a sustainable solution for reducing grid dependency and fossil fuel consumption in workplace environments. This study proposes a PV-powered EV charging system with an AC bus configuration and grid support to ensure stable and efficient operation. A comparative analysis of four DC-DC converter topologies—Dual Active Bridge (DAB), LLC Resonant, Interleaved Buck-Boost, and Interleaved Buck—is conducted for offboard charging applications. Performance evaluation is carried out using MATLAB/Simulink, considering voltage and current ripple, power density, stress levels, bidirectional capability, and control complexity. Component-level reliability is assessed using MIL-HDBK-217 standards to estimate failure rates …

Electrical Design For Moringa Leaf Dryer, Jake Weiss

Construction Management

The objective of this project is to provide a methodology to the electrical scope of mechanical leaf dryers. This dryer was particularly designed for an off-grid farm in New Longoro, Ghana in which resources and materials are limited. The electrical system must be designed so that it works with motors, variable frequency drives, worm gears, and other materials that could be sourced in Ghana. The system should also draw minimal power so that remaining photovoltaic energy could be utilized on the farm. The system should be simplistic and repeatable for other farmers to utilize. By using both a numerical analysis …

Nasa Weather Data Based Neural Network Grid Connected Pv System Maximum Power Point Tracking, Oluwatobiloba Mausi Johnson

Theses and Dissertations

Research and development for alternative energy sources that are cleaner, renewable, and have little to no environmental impact have been pushed by the ongoing rise in energy demand, the possibility of a decline in the use of conventional petroleum fuels, and concerns about environmental degradation. Electricity from photovoltaic (PV) systems is significantly better regarded among these alternative sources as a renewable energy source such as wind power, bioenergy, tidal energy, and hydroelectric with a wide application range because it is clean, accessible, and abundant with little to no environmental effect. However, solar energy usage is significantly impacted by the landscape, …

Design Of International Airport Hybrid Renewable Energy System, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

This paper presents the design and simulation of a hybrid renewable energy system utilizing solar and wind energy sources with a backup generator. The demand for reliable electric energy in support of investments in large social and economic development activities such as airport operations has been an agenda worldwide. In Tanzania, Mwanza International Airport (MIA) expects to consume about 18 MVA of electric power annually to support its operations for the next 25 years. About 78-80% of the world's commercial energy comes from fossil fuels. Non-renewable fuels and other negative effects contribute to global warming through greenhouse gas emissions and …

Evaluation Of Single Phase Smart Pv Inverter Functions In Unbalanced Residential Distribution Systems, Darren Symonette

Graduate Theses and Dissertations

In the United States, smart PV inverters integrated with residential distribution systems are becoming a more common occurrence. With integration of smart PV inverters, power utilities are experiencing an increase of number of operations with regards to switched capacitor banks, voltage regulators and on load tap changers. These increases can lead to excess wear and tear on the devices causing power utilities to perform unwanted replacement and maintenance. However, smart PV inverters when controlled under specific functions can enable these inverters to provide reactive power and voltage control which in turn lowers the number of operations for switched capacitor banks, …

A Model For Sustainable Adoption Of Solar Photovoltaic Technology In Tanzania, Joseph Kihedu

Tanzania Journal of Engineering and Technology (TJET)

The aim of the study was to develop a sustainable model for enhancement of the solar PV technology adoption in Tanzania. The model was developed based on the identified barriers that hinder the adoption of solar PV technology and adopted the best strategies from successful projects. Further, the drivers and activities were developed based on selected best strategies from successful projects. The identified barriers to the adoption of solar PV technology, which are grouped into five associated categories and their significances, are lack of access to finance (32%), non-enforcement of policy and regulation (31%), technical (18%), lack of awareness (9%) …

Foam-Based Floatovoltaics: A Potential Solution To Disappearing Terminal Natural Lakes, Koami Soulemane Hayibo, Joshua M. Pearce

Electrical and Computer Engineering Publications

Terminal lakes are disappearing worldwide because of direct and indirect human activities. Floating photovoltaics (FPV) are a synergistic system with increased energy output because of water cooling, while the FPV reduces water evaporation. This study explores how low-cost foam-based floatovoltaic systems can mitigate the disappearance of natural lakes. A case study is performed on 10%–50% FPV coverage of terminal and disappearing Walker Lake. Water conservation is investigated with a modified Penman-Monteith evapotranspiration method and energy generation is calculated with an operating temperature model experimentally determined from foam-based FPV. Results show FPV saves 52,000,000 m3/year of water and US$6,000,000 at 50% …

The Development Of An Inexpensive Alternative To Industry Solar Simulators, Raines A. Vanhuss

OUR Journal: ODU Undergraduate Research Journal

Solar cells are a prominent renewable energy source used in the twenty-first century. In order for the technology to grow, research lab equipment is needed to measure and characterizes these cells. This report covers solar simulator devices and proposes an alternative design solution to lessen the cost of solar cell lab equipment. Common household light sources were tested by generating I-V characteristics using an amorphous silicon solar cell. The light bulb that generated the best I-V curve was selected and then tested for the optimal distance between the light source and the solar panel. The alternative solar simulator was then …

Performance Loss Rate And Temperature Modeling In Predictive Energy Yield Programs For Utility-Scale Solar Power Plants, Katelynn M. Dinius

Master's Theses

The Gold Tree Solar Farm, designed by REC Solar, has a rated output power of 4.5 MW and began operation in 2018 to provide electricity to Cal Poly’s campus. Gold Tree Solar Farm site terrain consists of rolling hills and uneven slopes. The uneven typography results in interrow shading, requiring a modified tracking control algorithm to maximize power production. Predicting a utility solar field’s lifetime energy yield is a critical step in assessing project feasibility and calculating project revenue. The MATLAB-based predictive power model developed for this field overpredicted power in the middle of the day. The purpose of this …

Solar Pv Emulator, Tristan Studer, Cody Kremer

Electrical Engineering

The implementation of a solar PV emulator. Creating a controllable testing environment which sufficiently recreates realistic conditions a photovoltaic cell would experience in real world use. The project aims to accurately show the efficiency and reliability of a solar PV cell, opposed to an ideal model which creates unrealistic expectations. The PV emulator implements conditions such as: irradiance, soiling and temperate changes. It gives feedback on a displayed IV curve and/or PV curve so the user may graphically analyze the output their PV cell produces given various conditions. It allows the user selectable conditions the solar cell may experience this …

Solar Soiling Mitigation, Claire Desmith

Electrical Engineering

This senior project aims to mitigate performance losses that occur in Photovoltaic (PV) systems due to soiling of the panels. Soiling is the natural occurrence of debris accumulation on panels, depending on local climate conditions. Soiling loss refers to efficiency lost due to dirt and dust accumulation on the panels. The debris reduces system output by shading on a smaller scale. In addition to uniform soiling, corner soiling is observed in framed modules as debris collects in the corners of the modules. While solutions currently exist to clean modules to mitigate soiling losses, these solutions are often expensive and time …

Study Of Renewable Energy Penetration On A Benchmark Generation And Transmission System, Oluwaseun M. Akeyo, Aron Patrick, Dan M. Ionel

Electrical and Computer Engineering Faculty Publications

Significant changes in conventional generator operation and transmission system planning will be required to accommodate increasing solar photovoltaic (PV) penetration. There is a limit to the maximum amount of solar that can be connected in a service area without the need for significant upgrades to the existing generation and transmission infrastructure. This study proposes a framework for analyzing the impact of increasing solar penetration on generation and transmission networks while considering the responses of conventional generators to changes in solar PV output power. Contrary to traditional approaches in which it is assumed that generation can always match demand, this framework …

The Effect Of High Efficiency Building Technologies And Pv Generation On The Energy Profiles For Typical Us Residences, Evan S. Jones, Rosemary E. Alden, Huangjie Gong, Andrew G. Frye, Donald G. Colliver, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The penetrations of high efficiency technologies and photovoltaic (PV) generation are increasing in the residential sector. Technologies such as improved insulation and efficient HVAC systems significantly affect the energy profile of a house. This effect varies due to climate characteristics, i.e. temperature, solar radiation, relative humidity, and wind speeds. The effect of other technologies, such as efficient water heaters, lighting, or kitchen appliances, is mainly governed by human behavior, which may be represented by a schedule. This paper studies the performance of both climate-influenced and scheduled household devices among different levels of efficiency through combined computational and experimental methods. Three …

Energy And Economic Losses Due To Soiling On Utility Scale Pv Systems To Guide Timing Of Cost Effective Cleaning, Sophia Mcmillin Stockburger, Vicente Jesus Rios

Electrical Engineering

The purpose of this senior project is to develop and recommend a cleaning schedule for Goldtree Solar Farm that is both economically beneficial and an efficient use of cleaning for the client. Solar farms can have various factors that influence the cleaning schedule such as weather behavior, time of the year, soiling, and other factors. Through this senior project, the goal is to assess these factors effect on the solar farm to produce a cleaning schedule that will maximize energy production, maximize profits, and prevent insignificant cleaning

This analysis is motivated by defining and promoting the benefits of regular maintenance …

Neca Ghana Project, Michael T. Klee

Construction Management

Cal Poly’s motto is, “Learn by Doing" and for Cal Poly’s NECA Chapter, this isn’t simply a motto, but a directive for proactive change. For my senior project I will be leading the Cal Poly NECA chapter in the design, pre- fabrication and construction of a 5-7kw solar array, community center, ice production room and technology room in the remote fishing village of Agbokpa, Ghana. The solar array will power multiple industrial DC freezers, high efficiency LED lighting and charging stations while additionally powering water filtration and irrigation systems. Like many other fishing villages around the world, Agbokpa has no …

Triple-Junction Solar Cells : In Parallel., Levi C Mays

Electronic Theses and Dissertations

This paper looks into the current inefficiency of solar cells and attempts a few alternative solar cell structures in order to provide a more effective source of renewable energy. Currently, multi-junction solar cells are being developed to capture the sun’s light more efficiently. One of the ideas in this paper is to add a window to see if the addition of such a layer into a junction will increase the voltage while maintaining nearly the same current output. Central to this paper is the rearranging of the conducting layers of the multi-junction cell so that the junctions can be connected …

Pv Hybrid Inverter And Bess, Jacob Sussex, William Dresser, Owen Mckenzie, Jonathan Wharton, Derek Seaman

Electrical Engineering

The storage of energy from renewable sources such as photovoltaic based systems is a growing market, with 36 MWh of storage installed in Q1 of 2018. A report from EnergySage earlier this year states that in 2017, 74% of residential solar owners were also interested in energy storage systems. Mainstream systems like Tesla’s Powerwall are competing with other lithium-ion based storage systems from a wide number of providers on the market today. Short term and long term data collection on a system like this could be useful in designing future systems which perform better than the current market offerings. This …

Design And Analysis Of A Non-Isolated High Gain Step-Up Cuk Converter, Yasser Almalaq

Electronic Theses and Dissertations

Renewable energy sources, such as solar energy, are desired for both economic and ecological issues. These renewable energy sources are plentiful in nature and have a terrific capability for power generation. The only drawback of solar energy, which is one of the best forms of energy sources, is that the output has a low voltage and needs to be stepped up in order to be inserted into the DC grid or an inverter for AC applications. To overcome this drawback, a high gain DC-DC power converter is required in this kind of system. These power converters are needed for a …

The Analysis And Study Of Power System Designs For Same Polytechnic College In Tanzania, Kevin Lum Hua

Master's Theses

The Mbesese Initiative for Sustainable Development (MISD) is a group aiming to help eliminate extreme poverty in Africa by creating educational opportunity. One project that the group is currently doing is to build Same Polytechnic College (SPC) in Tanzania. As part of the project, this thesis aims to study and analyze the electrical power system and distribution for the college. Based on the projected load profile of the college and high potential for solar generation in Tanzania, several different power systems utilizing local utility AC electricity and/or photovoltaic (PV) DC electricity are explored and simulated for their feasibility and performance. …

Developing A 1-Megawatt Photovoltaic Power Plant For Liberty University, Andrew Knudsen

Senior Honors Theses

A photovoltaic power plant with a generation capacity of 1-megawatt is designed for Liberty University. Liberty University’s location and size are stated to provide context for the design. Design choices are presented, first with general information that is applicable to any photovoltaic plant design, then with significant factors that impact this design. Specific models of solar panels and inverters are selected after the necessary classifications are determined. The final design has 2,880 solar panels with a fixed angle 30⁰ above the horizon, has two central inverters, and takes up 2.57 acres. Future research is suggested for finances as well as …

Design & Evaluation Of A Hybrid Switched Capacitor Circuit With Wide-Bandgap Devices For Dc Grid Applications, Joshua L. Stewart

Electrical and Computer Engineering ETDs

ABSTRACT

As technologies advance, the rate at which renewable power sources, such as solar photovoltaic (PV) and wind, are being added to the power grid is increasing. Typically, PV power plants require large inverters for direct current to alternating current (DC-AC) power conversion, as well as large transformers to step up voltages to the grid voltage. Offshore wind farms and large PV power plants in remote locations often aggregate power on a DC bus in order to improve efficiency and reduce the cost of power conversion hardware within the energy complex. However, the power must still be converted to AC …

Structure Stability And Optical Response Of Lead Halide Hybrid Perovskite Photovoltaic Materials: A First-Principles Simulation Study, Siddharth Narendrakumar Rathod

Browse all Theses and Dissertations

A third-generation of solar cell is based on organic-inorganic hybrid perovskite materials. These have reached up to 22.1% conversion efficiency through exponential growth just within the last decade, compared to much longer improvement times for other photovoltaic technologies. Lead halide perovskites are among the most commonly used materials in this context. Despite the relatively large number of available works on some of these materials, in particular CH3NH3PbI3, others are less investigated. Here, we focused on CH3NH3PbCl3, CH3NH3PbBr3 and CH3NH3PbI3 for assessing structure stability and optical response. Using quantum-mechanics-based first principles approaches, we calculated the optimized structures of these three materials …

Configuration And Electronic Properties Of The Interface Between Lead Iodide Hybrid Perovskite And Self-Assembled Monolayers In Solar Cells, Parin Divya Amlani

Browse all Theses and Dissertations

Hybrid perovskite photovoltaic materials are currently the most promising functional materials for solar cell applications with efficiency reaching to those of more conventional materials such as silicon. Using self-assembled monolayers between photovoltaic materials and electrodes is a method for improving the stability and functionality. Recent experiments have shown that using 4-mercaptobenzoic acid and pentafluorobenzenethiol monolayers bridging lead iodide hybrid perovskite photovoltaic materials and electrodes result in improved stability and efficiency. The details of monolayer assembly, molecular adsorption configuration, and resulting modification of electronic properties are important characteristics related to solar cell performance. These characteristics can be obtained through accurate computer …

Photovoltaic Cooking In The Developing World, Tyler Watkins, Christopher O'Day, Omar Arriaga

Mechanical Engineering

The challenge of clean cooking is faced by hundreds of millions of people worldwide. We present a cooking technology consisting of a solar panel directly connected to an electric heater in a well-insulated chamber. Assuming continued decrease in solar panel prices, we anticipate that in a few decades Solar Electric Cooking technologies will be the most common cooking technology for the poor. Appropriate use of insulation reduces the power demand making low-power Insulated Solar Electric Cooking systems already cost competitive.

Simulation, Measurement, And Emulation Of Photovoltaic Modules Using High Frequency And High Power Density Power Electronic Circuits, Yunas Erkaya

Electrical & Computer Engineering Theses & Dissertations

The number of solar photovoltaic (PV) installations is growing exponentially, and to improve the energy yield and the efficiency of PV systems, it is necessary to have correct methods for simulation, measurement, and emulation. PV systems can be simulated using PV models for different configurations and technologies of PV modules. Additionally, different environmental conditions of solar irradiance, temperature, and partial shading can be incorporated in the model to accurately simulate PV systems for any given condition.

The electrical measurement of PV systems both prior to and after making electrical connections is important for attaining high efficiency and reliability. Measuring PV …

Simulation Design For Photovoltaics Using Finite Difference Time Domain And Quadratic Complex Rational Function Methods, Jacob R. Duritsch, Haejun Chung, Peter Bermel

The Summer Undergraduate Research Fellowship (SURF) Symposium

Photovoltaics (PV) can in principle supply enough renewable energy to offset a great deal of fossil fuel usage. To achieve this transition, it is critical to develop improved PV cells with decreased material costs and improved efficiencies. This goal can be greatly facilitated by a tool simulating the absorption and efficiency of experimentally relevant 3-D PV designs made of realistic materials, including those that have not yet been discovered. By incorporating the quadratic complex rational function algorithm (QCRF) with the finite difference time domain methods (FDTD), simulations can include frequency response and optical properties, while allowing full customization of tandem …

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …