Power and Energy Commons^™

Modeling And Analysis Of A Four-Switch Buck-Boost Dynamic Capacitor, Oscar Plasencia

Master's Theses

Modern electric power utilities are facing a variety of challenges introduced by the increasing complexity of their operation, structure, and consumer loads. One such challenge has been to supply the ever growing demand for reactive power which is essential for grid support. For this reason dynamic VAR technologies are becoming much more important to modern day power systems. A recent dynamic VAR technology known as the Dynamic Capacitor offers full quadrant capacitive VAR control through the combination of AC/AC buck and boost cells. This paper introduces a new topology deemed the “Four-Switch Buck-Boost Dynamic Capacitor” which promises to combine the …

Digitally Controlled, Modular Electronic Load, Jason L. March

Master's Theses

This project entails the design and development of a digitally controlled, modular electronic load. The proposed load is unique from existing designs because it has the added ability to increase its maximum current level by adding identical modules in parallel. Each module is designed to sink a maximum of 5A at 60V but more modules allow for more current. The cost and simplicity of the design are considered such that it can be reproduced in-house to replace, whenever possible, the resistor box for load testing of any analog circuits but more specifically power electronic circuits.

The design process as well …

Impacts Of Plug-In Electric Vehicle On Residential Electric Distribution System Using Stochastic And Sensitivity Approach, Henry Chigozie Ureh

Master's Theses

Plug-in Electric Vehicles (PEVs) are projected to become a viable means of transportation due to advances in technology and advocates for green and eco-friendly energy solutions. These vehicles are powered partially, or in some cases, solely by the energy stored in their battery packs. The large sizes of these battery packs require large amount of energy to charge, and as the demand for PEV increases, the increase in energy demand needed to recharge these PEV batteries could pose problems to the present electric distribution system. This study examines the potential impacts of PEV on a residential electric distribution system at …

Development And Prototyping Of A Ground Fault Circuit Interrupter For 3-Phase 480 Volt Systems, Matthew R. Norlander

Master's Theses

Ground Fault Circuit Interrupter (GFCI) technology was first introduced in the NEC in 1971, yet four decades later the technology has not been introduced to a great extent outside of the home environment. This thesis introduces the difficulties encountered in low-voltage three phase ground fault current detection, and adopts a previously patented tripping scheme to develop and prototype a digital relay for 3-phase 480 volt systems capable of the sensitivity and speed required for personnel safety. Results demonstrate the feasibility of the concept and suggest commercial development should be pursued. The prototype is capable of mA sensitivity and reliably detects …

Morphology Changes In Pcpdtbt:Pcbm And P3ht:Pcpdtbt:Pcbm And Its Effect On Polymer Solar Cell Performance, Galen David Cauble

Physics

Polymer solar cell morphology is sensitive to both heat and time. By thermally annealing polymer solar cells the morphology of the devices can be altered causing immediate changes in device performance. Blending PCPDTBT:PCBM with P3HT:PCPDTBT combines the absorption characteristics of each to create a more even absorption spectrum. Subjecting PCPDTBT:PCBM, and P3HT:PCPDTBT:PCBM polymer solar cells to thermal annealing as well as recording device performance through time has shown that P3HT:PCPDTBT:PCBM devices react positively to thermal annealing (increasing from 0.8% to 1.4%) while PCPDTBT:PCBM devices have varied reactions. Furthermore, the P3HT:PCPDTBT:PCBM devices have achieved efficiencies of 1.6% in AM 1.5 compared …

Constant Conduction Angle Experimental Generation For Rf Power Amplifiers, Michael Spahn

Electrical Engineering

As the demand for more devices to become wireless increases, there is a need for linear, efficient monolithic power amplifiers to deal with the variations in modulation of signals. With partial support from Cal Poly C3RP Grant #52268, this paper explains the implementation of and analyzes a circuit that actively biases a bipolar transistor to operate as a Class C amplifier. The Class C amplifier can maintain constant conduction angle over a range of output powers by using a Class B amplifier to force a scaled DC current vs. input magnitude curve on to a Class C amplifier. The knee …

Wireless Passive Power Transfer Using Wire Antennas, Sheng Da Zhang

Electrical Engineering

This project tests and analyzes the efficiency of directional and omnidirectional antennas in wireless power transfer for charging. The project demonstrates the steps of construction and properties of dipole, monopole, and Yagi Uda antennas. A low power high frequency DC rectifier circuit converts the received RF power from the antenna and stored it as DC voltage on a capacitor. The receiver circuit also estimates the power received by the antenna. Wireless RF power transmission proves to be inefficient for short distances. The best efficiencies of the antennas were under 50% even at 0.1meter. The near field attenuation starts at around …

140 New Montgomery Power Distribution Design, Stephen Shaffer

Electrical Engineering

The Power Distribution Design for a high-rise building requires a great deal of coordination and design from the structural, electrical, mechanical, telecommunication, and PG&E engineers. This report will cover how I was able to coordinate and design the power distribution system for 140 New Montgomery, a 28 story building located in San Francisco. Furthermore, this report will cover the steps taken in the future to ensure a smooth transition from the schematic design phase to the construction document phase.

Benefits Of Near-Term Cloud Location Forecasting For Large Solar Pv, Timothy Robert Rudd

Master's Theses

As the ‘green’ energy movement continues to gain momentum, photovoltaic generation is becoming an increasingly popular source for new power generation. The primary focus of this paper is to demonstrate the benefits of close-to real-time cloud sensing for Photovoltaic generation. In order to benefit from this close-to real-time data, a source of cloud cover information is necessary. This paper looks into the potential of point insolation sensors to determine overhead cloud coverage. A look into design considerations and economic challenges of implementing such a monitoring system is included. The benefits of cloud location sensing are examined using computer simulations to …

Project 308: Augmented Reality Mario Kart, Joseph Abad, David Allender, Joryl Calizo, Ryan Gaspar, Gavin Lee

Computer Engineering

Mario Kart is a popular go-kart racing game developed by Nintendo. The premise of the game is simple: drive a go-kart along a racetrack and reach the finish line before the other players. What makes this game unique, however, is the inclusion of weapons, traps, and other projectiles that a player can use to gain an advantage in the race. We have taken on the challenge of not only recreating this amazing game, but using the art of Augmented Reality to fully immerse the player in the full experience. Rather than play the game on a television screen with a …

Design, Fabrication, And Testing Of An Electromagnetic Rail Gun For The Repeated Testing And Simulation Of Orbital Debris Impacts, Jeff Maniglia, Jordan Smiroldo, Alex Westfall, Guy Zohar

Aerospace Engineering

An Electromagnetic Railgun (EMRG) was designed, built, and tested, capable of firing a projectile a 1 gram projectile at 650 m/s muzzle velocity. The EMRG utilizes an injector, a high voltage power supply, a capacitor bank, inductors and rails. The injector fires 2300 psig Nitrogen gas into the system to provide an initial velocity. The high voltage power supply charges the capacitor bank. The capacitor bank discharges the electric potential built up through the projectile while inside the rails in order to create the EMRG’s force. The inductors are used to pulse form the capacitor bank in order to get …

Portable Solar Desalination System, Genaro Sanchez, Alan Galarza, Erick Del Real

Electrical Engineering

Clean water and reliable energy can be difficult to obtain in remote locations such as desert villages, secluded islands, and other places where no fresh water can be found. The primary goal for this project is address these problems by implementing a portable desalinization plant system that is to be powered by solar energy PV system as the main energy source.

Sick Laser Scanner Power Supply For Use With A Yamaha Rmax Uav, Elliot Due

Electrical Engineering

No abstract provided.

60 Watt Embedded Solar Cell Umbrella, Matthew Devoss

Electrical Engineering

No abstract provided.

Cal Poly Power System Design & Analysis, Minesh D. Patel

Electrical Engineering

The scope of this project encompasses the design and analysis of the Cal Poly Power System at the distribution level using the SKM software environment. The purpose is to accurately model the power system in software so theoretical calculations and analysis can be executed. This requires sufficient preliminary research to obtain data for the main buildings on campus, sound interpretation of one line diagrams, designing the system within the software using realistic values and then performing analysis to model real world situations. The data collected is under maximum load conditions for a specified time period using medium voltage parameters. The …

Programmable Household Led Light Fixture, Jordan Locano

Electrical Engineering

This report details the development and construction of a LED light fixture to be used for household lighting. This document details background information, design ideas, project specifications, production, assembly, testing, and conclusions involved with this project. The goals of this project is to design and build a cost-effective replacement for traditional room lighting that can perform better and last longer than traditional methods.

Development Of Wind Tunnel For Laboratory Wind Turbine Testing, Danny Alexander Zepeda

Electrical Engineering

A wind tunnel with a 0.5 HP motor was purchased by Cal Poly Electrical Engineering Department from Hampden for $16,000. It can only simulate winds of up to 10 MPH. The tunnel has a manual dial that controls the wind speed. It also measures the voltage and current output with an analog measure display. This wind tunnel was expensive and unfortunately cannot achieve very high wind speeds. For this reason, a similar wind tunnel with more potential and with a smaller budget was proposed to be built for use in the Sustainable Energy Lab. The new wind tunnel that was …

Solar Powered Electric Clothes Dryer, Roger Mai, Alan Swe

Electrical Engineering

Appliances that consume the most energy in a household usually involve heating, and an electric clothes dryer is one such appliance, consuming up to 4KW of power. The most environmentally friendly way is to hang clothes outside to dry, a natural solar and wind powered method, but unfortunately most people are unable to do so as some neighborhood communities do not allow the hanging of laundry outside as it is regarded as “unsightly”, for example. This project aims to provide an alternate solution to the wall-powered electric clothes dryer by designing one which operates entirely off the grid.

Current Tracking Power Supply For Sensor Calibration, Joshua Brookley

Electrical Engineering

This report highlights the steps taken to design and develop a constant 5V power supply capable of tracking load current. The background of its previous design, its necessary specifications and steps taken to achieve specifications are highlighted throughout the report. The report also contains conclusions and final recommendations for the design chosen, including its strengths and drawbacks.

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Wind Power Generator Design For The Dc House Project, Evan Lim, Samson Liu

Electrical Engineering

The purpose of this project is to introduce a cost efficient alternative in converting wind into energy for third world countries. Currently there are approximately 1.6 billion people who have limited access to electricity. As part of the DC House project, we hope to develop a solution for them as the use of electricity is becoming an essential part of life. One of the natural energy resources to provide power to the DC House is wind. The components used for the project are a DC motor and DC-DC converter to translate wind into power and produce DC voltage and current, …

Variable Dc Voltage Wall Outlet For The Dc House Project, Michael Detmers, Tyler J. Blauvelt

Electrical Engineering

This senior project report will focus on explaining the design and operation of a variable DC wall outlet for use in the DC house. Testing will include the use of various loads using different input DC voltages not exceeding a maximum output of 90W.

The most important aspects of the outlet are to have a highly-efficient converter efficiency as well as system isolation from the main DC bus on the input. This report will outline the purpose and way of achieving isolation through use of a Flyback DC-DC converter. The user interface is the second significant aspect and details of …

Bicycle-Powered Ac Generator, Andrew Austin

Electrical Engineering

The purpose of this senior project is to design, build, and be able to present a mechanism that will produce AC power using the mechanical energy produced by a person pedaling a standard bicycle. Also, I would like to be able to show the user and the audience the advantage of using compact fluorescent bulbs, and in doing so, make them more conscience of energy-saving products. To do this, I must present a stand that can support a bicycle with a rider, a way to convert the wheel’s motion to DC power, to convert that DC power to usable AC …

Solar Instrumentation Lab, Rene Canedo Iii, Rong Gui Chen

Electrical Engineering

This project is a mobile platform that will allow experiments on different solar panels to be done easily while keeping the cost of the lab to a minimum. California Polytechnic State University’s motto is ‘learn by doing’ and this lab structure will allow students to get practical experience with photovoltaic cells and the instruments that are required to take measurements. The solar instrumentation lab is a potential hardware lab for the electrical engineering department’s Sustainable Electric Energy Conversion class EE 420 and Solar-Photovoltaic Systems Design EE 520. This group took the current solar structure as a base for the lab’s …

Exercise Bicycle Dc-Dc Converter For The Energy Harvesting From Exercise Machines Project, Ryan Rickard, Logan Stowe

Electrical Engineering

Project is a continuation of previous projects that seek an efficient DC to DC converter for the existing exercise bicycle system created by Mechanical and Electrical Engineering students. This DC-DC converter is to integrate with the wide range of DC voltages produced by the bicycle in order to produce a constant optimal voltage for charging a car battery. This converter will boost voltages when the bicycle outputs below the optimal voltage and buck voltages when above. The converter will take EHFEM one step closer to its overall and final goal of harvesting energy from the exercise machines in Cal Poly’s …

Solar Powered Backpack, Saagar Sabharwal, Tom Poonsopin

Electrical Engineering

One popular motto in electrical engineering today is “going green.” This project will convert the sun’s energy into reusable energy. The purpose of this senior project is to develop a solar powered backpack that can charge certain portable USB devices for students. Many students walk around campus with an iPod or cell phone, which has surely died or ran low on batteries at least once when needed most. This backpack will allow students to charge their devices “on the go.” When students walk or bike around campus, the solar panels attached to the backpack will allow recharging of their portable …

Brushless Dc Motor Design And Build, Justin Damele

Electrical Engineering

Complete Design and Build of a Brushless DC Motor. Everything was manufactured using various Lathes and End Mills. Everything built from scratch.

Android Application Controlled Surge Protector, Lok An

Electrical Engineering

A significant amount of consumer electronics cannot be switched off completely without being unplugged. Standby power, also known as phantom power, refers to the electric power consumed by electronic appliances when they are switched off. There are some devices that need constant power; items like alarm clocks and security systems need constant power to function correctly. Some devices, such as video game consoles and televisions, consume power without offering any features. Electricity lost from standby power has been increasing with the amount of consumer electronics increasing in households.

This project’s goal is to create a low power remote that can …

Wireless Sensor Network For Energy And Environmental Monitoring: Helping Old Buildings Go Green, Jacob Power

Electrical Engineering

Today, the rising cost of energy and social trend of “going green” has put increasing pressure on commercial property owners to improve the efficiency of their investments. There is good reason for this, too. In the State of California, office buildings represent the single largest user of energy in the commercial sector. This project consisted of the design, implementation, construction, testing, and deployment of a wireless sensor network for energy and environmental monitoring in retrofit commercial office installations. The analyzed data generated by this system can be used by building management and owners to identify areas of inefficiency within the …

Dc House Modeling And System Design, Jessica E. Chaidez

Electrical Engineering

This project entails the study and design of DC power distribution for the DC House Project. Wire size, common high efficient loads, maximum power input, and different distribution system implementation (ring or radial) play a major role when designing an efficient, low-voltage distribution system. Efficiency is determined based on which main bus voltage powers all the loads with minimal power loss. Power efficiency is heavily dependent in DC-DC converter efficiencies due to the power loss in converting the voltage from high to low, or vice versa. Selection of the wire size plays a major role in power losses. There are …