Power and Energy Commons^™

Lithium-Based Battery System Management And Balancing, William Joel Schmidt Iii

Purdue Polytechnic Masters Theses

This thesis builds upon previous work completed for the design and evaluation of active lithium battery system management. Simulations were performed to provide a comparison for the hardware that was designed, built, and tested. An analysis of the simulation and hardware results was completed to support or disprove the initial hypothesis. A DC-DC converter was used as the source for the balancing current. Lithium polymer batteries with a 5Ah capacity were used for testing the designed hardware. The findings showed that there is a reduction in the system voltage swing during balancing as well as less time taken to decrease …

Highly Efficient Maximum Power Point Tracking Using A Quasi-Double-Boost Dc/Dc Converter For Photovoltaic Systems, Christopher J. Lohmeier

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Solar photovoltaic (PV) panels are a great source of renewable energy generation. The biggest problem with solar systems is relatively low efficiency and high cost. This work hopes to alleviate this problem by using novel power electronic converter and control designs. An electronic DC/DC converter, called “Quasi-Double-Boost DC/DC Converter,” is designed for a Solar PV system. A Maximum Power Point Tracking (MTTP) algorithm is implemented through this converter. This algorithm allows the PV system to work at its highest efficiency. Different current sensing and sensorless technologies used with the converter for the MPPT algorithm are offered and tested. Design aspects …

Design And Control Of High Power Density Motor Drive, Dong Jiang

Doctoral Dissertations

This dissertation aims at developing techniques to achieve high power density in motor drives under the performance requirements for transportation system. Four main factors influencing the power density are the main objects of the dissertation: devices, passive components, pulse width modulation (PWM) methods and motor control methods.

Firstly, the application of SiC devices could improve the power density of the motor drive. This dissertation developed a method of characterizing the SiC device performance in phase-leg with loss estimation, and claimed that with SiC Schottky Barrier Diode the advantage of SiC JFET could benefit the motor drive especially at high temperature. …

Impacts Of Plug-In Electric Vehicle On Residential Electric Distribution System Using Stochastic And Sensitivity Approach, Henry Chigozie Ureh

Master's Theses

Plug-in Electric Vehicles (PEVs) are projected to become a viable means of transportation due to advances in technology and advocates for green and eco-friendly energy solutions. These vehicles are powered partially, or in some cases, solely by the energy stored in their battery packs. The large sizes of these battery packs require large amount of energy to charge, and as the demand for PEV increases, the increase in energy demand needed to recharge these PEV batteries could pose problems to the present electric distribution system. This study examines the potential impacts of PEV on a residential electric distribution system at …

Development And Prototyping Of A Ground Fault Circuit Interrupter For 3-Phase 480 Volt Systems, Matthew R. Norlander

Master's Theses

Ground Fault Circuit Interrupter (GFCI) technology was first introduced in the NEC in 1971, yet four decades later the technology has not been introduced to a great extent outside of the home environment. This thesis introduces the difficulties encountered in low-voltage three phase ground fault current detection, and adopts a previously patented tripping scheme to develop and prototype a digital relay for 3-phase 480 volt systems capable of the sensitivity and speed required for personnel safety. Results demonstrate the feasibility of the concept and suggest commercial development should be pursued. The prototype is capable of mA sensitivity and reliably detects …

Using Reputation Based Trust To Overcome Malfunctions And Malicious Failures In Electric Power Protection Systems, Jose E. Fadul

Theses and Dissertations

This dissertation advocates the use of reputation-based trust in conjunction with a trust management framework based on network flow techniques to form a trust management toolkit (TMT) for the defense of future Smart Grid enabled electric power grid from both malicious and non-malicious malfunctions. Increases in energy demand have prompted the implementation of Smart Grid technologies within the power grid. Smart Grid technologies enable Internet based communication capabilities within the power grid, but also increase the grid's vulnerability to cyber attacks. The benefits of TMT augmented electric power protection systems include: improved response times, added resilience to malicious and non-malicious …

Analysis Of Converter Connected Synchronous Wind Turbines To Grid Disturbances., Joseph Kearney, Michael Conlon, Eugene Coyle

Conference papers

This paper investigates the performance of synchronous generators to grid voltage unbalance and grid faults. A Model of a synchronous generator with a full converter is implemented in the SimPowerSystems toolbox in Matlab/Simulink. Methods to modify the converter control schemes to improve the synchronous generator systems response to grid voltage unbalance and grid faults are investigated. Grid faults including grid voltage unbalance, and line-to-ground faults are introduced into the model at specific times to analyse the performance of the wind generation system. Improvements in the performance of the synchronous generator WECS to the grid disturbances are illustrated.

Nonlinear Multivariable Modeling Of Solid Oxide Fuel Cells Using Core Vector Regression, M. Mohammadi, M. Raoofat, Hesamoddin Marzooghi, G. B. Gharehpetiangharehpetian

Hesamoddin Marzooghi

This paper presents new steady-state and dynamic models for solid oxide fuel cells (SOFCs) using core vector regression (CVR). So far, most of conventional SOFC models have been presented based on conversion laws. Due to complex mathematical equations used in these models, they are time-consuming and need large amount of memory to be applied for controller design, especially power electronic interface controller design, generation and load predictions, optimization and other studies. To overcome these problems, some black-box models, such as support vector machine (SVM) and artificial neural network (ANN)-based models have been also proposed for SOFC. In this paper, in …

A Review Of Parallel Operation Of Active Power Filters In The Distributed Generation System, Shafiuzzaman Khan Khadem, Malabika Basu, Michael Conlon

Conference papers

In this paper a technical review of parallel operation of Active Power Filter (APF) for harmonic power compensation in distributed generation (DG) network has been presented. Controlling methods and connection topologies with their pros and cons are described. Recent improvements in controlling and future trends for the application of APFs in distributed mode are also identified.

Experimental And Numerical Investigations Of Tubular-Shaped Direct Methanol Fuel Cells (Dmfcs), Travis R. Ward

Master's Theses

This study focuses on both the numerical and experimental investigations of the novel, passively operated, tubular-shaped, Direct Methanol Fuel Cell (DMFC) as an alternative geometry to the traditional planar-shaped fuel cell. The benefit of the tubular geometry compared to the planar geometry is the higher instantaneous volumetric power density provided by the larger active area, which could be beneficial in applications that require a high instantaneous power while occupying a small volume. First, a two-dimensional, two-phase, non-isothermal model was developed to investigate the steady-state performance and design characteristics of a tubular-shaped, passive DMFC. It was found that a higher ambient …

Virtual Power Lab - D.E.I. Dayalbagh, D. K. Chaturvedi Dr.

D. K. Chaturvedi Dr.

Electrical Machines and Power systems are the back bone of electrical engineering and play a vital role in industry. Hence, it is essential for electrical engineering students to learn the concepts of power systems and machines. Unfortunately, the students are loosing interest in lab work due to various reasons like unavialability of experimental setups, lack of qualified and motivated lab staff, lab timing, etc. To overcome these problems the virtual Power labs are very important to impart quality experiments.

Constant Conduction Angle Experimental Generation For Rf Power Amplifiers, Michael Spahn

Electrical Engineering

As the demand for more devices to become wireless increases, there is a need for linear, efficient monolithic power amplifiers to deal with the variations in modulation of signals. With partial support from Cal Poly C3RP Grant #52268, this paper explains the implementation of and analyzes a circuit that actively biases a bipolar transistor to operate as a Class C amplifier. The Class C amplifier can maintain constant conduction angle over a range of output powers by using a Class B amplifier to force a scaled DC current vs. input magnitude curve on to a Class C amplifier. The knee …

Accurate Circuit Model For Predicting The Performance Of Lead-Acid Agm Batteries, Wenxin Peng

UNLV Theses, Dissertations, Professional Papers, and Capstones

Energy storage technologies are becoming of great importance in many modern electrical systems. In particular, electrochemical batteries are rapidly gaining wide-spread application in transportation systems as well as in the electric utility sector, where they provide a means to convert non-dispatchable renewable resources into dispatchable generation sources. Hence, accurate battery models are needed during the design stage of such systems to forecast future performance.

A variety of models with a varying degree of complexity and accuracy currently exist that predict battery behavior. In the proposed paper, an existing battery model is modified to account for some battery irregularities while maintaining …

Design, Modeling And Control Strategy Of Pv/Fc Hybrid Power System, Dr. Adel A. Elbaset

Dr. Adel A. Elbaset

This paper describes development of a general methodology of an autonomous PV/FC system composed of photovoltaic (PV), electrolyzer, hydrogen storage tank and fuel cell (FC). The aim of this paper is to determine optimum design, control strategy, economic and performance of a PV/FC hybrid power generation system without battery storage taking into account all losses in the system. The paper also presents a computer program based on Matlab software to determine optimum design, control strategy, economic and performance of an autonomous PV/FC hybrid power generation system. The computer program develops to size system components in order to match the load …

Exposing To Emf, Prof Dr. Mahmoud Moghavvemi, Farhang Alijani, Hussein Ameri, Maryam Ashayer Soltani

Professor Mahmoud Moghavvemi

In the recent years, by developing the usage of new popular Electronic-Communication gadgets and home appliances like Mobile Phones and Microwave Ovens which are mostly

sources of Electromagnetic Wave Radiation, a severe public concern regarding the sideeffects “whether positive or negative” on human health and environment has been arisen. It means that there are new challenging issues rather than old one “the exposing to low radiofrequency emissions” which have been studied for past decades. Indeed, for more than 100 years, human has exposed to the Radio-waves radiation from Radio & TV broadcasting

transmitters besides the Radar and point to point …

Project 308: Augmented Reality Mario Kart, Joseph Abad, David Allender, Joryl Calizo, Ryan Gaspar, Gavin Lee

Computer Engineering

Mario Kart is a popular go-kart racing game developed by Nintendo. The premise of the game is simple: drive a go-kart along a racetrack and reach the finish line before the other players. What makes this game unique, however, is the inclusion of weapons, traps, and other projectiles that a player can use to gain an advantage in the race. We have taken on the challenge of not only recreating this amazing game, but using the art of Augmented Reality to fully immerse the player in the full experience. Rather than play the game on a television screen with a …

Programmable Household Led Light Fixture, Jordan Locano

Electrical Engineering

This report details the development and construction of a LED light fixture to be used for household lighting. This document details background information, design ideas, project specifications, production, assembly, testing, and conclusions involved with this project. The goals of this project is to design and build a cost-effective replacement for traditional room lighting that can perform better and last longer than traditional methods.

Current Tracking Power Supply For Sensor Calibration, Joshua Brookley

Electrical Engineering

This report highlights the steps taken to design and develop a constant 5V power supply capable of tracking load current. The background of its previous design, its necessary specifications and steps taken to achieve specifications are highlighted throughout the report. The report also contains conclusions and final recommendations for the design chosen, including its strengths and drawbacks.

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Variable Dc Voltage Wall Outlet For The Dc House Project, Michael Detmers, Tyler J. Blauvelt

Electrical Engineering

This senior project report will focus on explaining the design and operation of a variable DC wall outlet for use in the DC house. Testing will include the use of various loads using different input DC voltages not exceeding a maximum output of 90W.

The most important aspects of the outlet are to have a highly-efficient converter efficiency as well as system isolation from the main DC bus on the input. This report will outline the purpose and way of achieving isolation through use of a Flyback DC-DC converter. The user interface is the second significant aspect and details of …

Exercise Bicycle Dc-Dc Converter For The Energy Harvesting From Exercise Machines Project, Ryan Rickard, Logan Stowe

Electrical Engineering

Project is a continuation of previous projects that seek an efficient DC to DC converter for the existing exercise bicycle system created by Mechanical and Electrical Engineering students. This DC-DC converter is to integrate with the wide range of DC voltages produced by the bicycle in order to produce a constant optimal voltage for charging a car battery. This converter will boost voltages when the bicycle outputs below the optimal voltage and buck voltages when above. The converter will take EHFEM one step closer to its overall and final goal of harvesting energy from the exercise machines in Cal Poly’s …

Solar Powered Backpack, Saagar Sabharwal, Tom Poonsopin

Electrical Engineering

One popular motto in electrical engineering today is “going green.” This project will convert the sun’s energy into reusable energy. The purpose of this senior project is to develop a solar powered backpack that can charge certain portable USB devices for students. Many students walk around campus with an iPod or cell phone, which has surely died or ran low on batteries at least once when needed most. This backpack will allow students to charge their devices “on the go.” When students walk or bike around campus, the solar panels attached to the backpack will allow recharging of their portable …

Wireless Sensor Network For Energy And Environmental Monitoring: Helping Old Buildings Go Green, Jacob Power

Electrical Engineering

Today, the rising cost of energy and social trend of “going green” has put increasing pressure on commercial property owners to improve the efficiency of their investments. There is good reason for this, too. In the State of California, office buildings represent the single largest user of energy in the commercial sector. This project consisted of the design, implementation, construction, testing, and deployment of a wireless sensor network for energy and environmental monitoring in retrofit commercial office installations. The analyzed data generated by this system can be used by building management and owners to identify areas of inefficiency within the …

Design And Simulation Of V2g Bidirectional Inverter And Dc-Dc Converter, Allan Agatep, Mason Ung

Electrical Engineering

As plug-in hybrid electric vehicles (PHEV) become more popular, the utility companies are forced to feed the grid more electricity. However, these PHEVs are capable of providing power to the grid when they are parked serving as ancillary systems for grid regulation (V2G). Using a system based on photovoltaic (PV) technology, a design for a bidirectional inverter with LCL filter, and a bidirectional dc-dc with a constant current controller, was constructed using LTspice. Various papers were researched and analyzed to determine applicable designs for components. Simulations show the designs are capable of bidirectional power transfer. ETAP simulations show that delivering …

Photovoltaic Emulator Adaptable To Irradiance, Temperature And Panel Specific I-V Curves, Joseph Gamos Durago

Master's Theses

This thesis analyzes the design and performance of a photovoltaic (PV) emulator. With increasing interest in renewable energies, large amounts of money and effort are being put into research and development for photovoltaic systems. The larger interest in PV systems has increased demand for appropriate equipment with which to test PV systems.

A photovoltaic emulator is a power supply with similar current and voltage characteristics as a PV panel. This work uses an existing power supply which is manipulated via Labview to emulate a photovoltaic panel. The emulator calculates a current-voltage (I-V) curve based on the user specified parameters of …

Bridgeless Active Power Factor Correction Using A Current Fed Push Pull Converter, Jeramie Seth Bianchi

Master's Theses

ABSTRACT

Bridgeless Active Power Factor Correction

Using a Current Fed Push Pull Converter

Jeramie Seth Bianchi

Switched Mode Power Supplies have become increasingly popular for efficient methods of delivering power to an assortment of electronic devices. This thesis proposes a method of using a current fed push pull converter to provide active power factor correction and rectification in a single stage. While most AC-DC converters utilize a bridge rectifier to convert AC-DC and then perform DC-DC conversion, the proposed circuit will utilize its output diodes to perform rectification, thus eliminating the need for a bridge rectifier. This circuit will also …

Off-Grid Public Lighting System – Design And Characterization Of An Led Luminaire, Quanghuy Le

Master's Theses

The technological advances made in the photovoltaic industry have led to a vast exploration of self-sustaining systems. As the consumer demand for electricity rises from increasing population and development of existing technologies, new practices in system designs are required to relieve the impact on the electrical grid.

This thesis delves into a developing concept of using photovoltaic modules for roadway lighting, with emphasis on establishing the fundamental design for a “spot-lighting” luminaire. By effectively extinguishing various sections of the luminaire in the absence of pedestrian trafficking, the proposed design and implementation will minimize the prolonged costs, as well as the …

Modeling And Analysis Of The Effects Of Pcb Parasitics On Integrated Dc-Dc Converters, Darwin Domingo Fernandez

Master's Theses

Load transients are prevalent in every electronic device including semiconductor memory, card readers, microprocessors, disc drives, piezoelectric devices, and digitally based systems. They are capable of producing voltage stress, introducing noise, and degrading device functionality. In order to avoid damage to the device, a feedback control loop is implemented with system compensation to regulate the output voltage deviations by the converter. Because designing compensation networks can be rather complicated, DC-DC converters with integrated feedback control topologies help minimize design time and complexity of converter compensation at the expense of design flexibility. This thesis widens the limitations of an integrated DC-DC …

Experimental Study Of Shoot-Through Control Methods For Z-Source Inverter, Omar Ellabban, Joeri Van Mierlo, Philippe Lataire

Omar Ellabban

This paper presents a simulation and experimental comparative analysis of the Z-source inverter (ZSI) with four different shoot-through (ST) control methods, namely: the simple boost control, the maximum boost control, the maximum constant boost control and the modified space vector modulation boost control methods. A review of these methods is presented with a summary of all expressions. A prototype of a 30 kW ZSI is designed and implemented. The eZdsp™ F2808 evaluation board is used for the realization of the shoot-through control methods and the real time workshop (RTW) is used for automatic code generation. The paper compares between the …

Elliptical Machine Dc-Dc Converter For The Energy Harvesting From Exercise Machines Project, Greg Hollister

Electrical Engineering

Designing a DC/DC Converter for the Cal Poly Energy Harvesting from Exercise Machines project requires special attention to the unique operating characteristics of the source and the load. An elliptical machine powered by a person exercising comprises the source, while an AC Inverter makes up the load. This project attempts to integrate the two devices with a custom DC/DC Converter in order to ultimately deliver power back into the power grid.