Power and Energy Commons^™

Load Flow Solution For Three-Phase Mv Radial Distribution Connected Network Supplying Different Line Topologies, B. J. Kundy

Tanzania Journal of Engineering and Technology (TJET)

In this paper, a load flow solution for the Medium Voltage (MV) three-phase radial distribution in delta-delta (Δ–Δ) connected network supplying different line topologies such as three phase, phase to phase and single-wire earth return (SWER) networks is presented. The general voltage related network equations are developed using Kirchhoff’s voltage and current laws. Development of a solution to the load flow analysis applying the developed general voltage related network equations is proposed in order to evaluate the network voltage profile. Various numbers of arrays are developed for the identification of the network under study. The proposed method is a new …

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang

Journal of Electrochemistry

In this work, potential-modulation method was used in two-step anodization process to make an AAO template with Y-type nanochannels. Then Y-type carbon nanotubes with controlled length and branch angle were prepared in the template based on chemical vapor decomposion (CVD) method with Co particles as catalyst and C₂H₂ as carbon source. The Y-type nanotube branches exhibit the angle distribution ranging from 20° to 120°. The results demonstrated that the oxidation potential should be responsible for the angles and length of the branches. Short pulse and high oxidation potential will result in the short and dense nanotube branches.

Study On The Gas Generation In Different Charging Voltage During Formation Process In Polymer Lithium-Ion Battery, Li Huang, Ming-Gang Jin, Hui-Qun Cai, Ming-Sen Zheng, Quan-Feng Dong, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

The gases of polymer lithium-ion battery (PLI) generated under different voltages during the first charging process were examined by means of gas chromatography (GC), and the mechanism of the gas generation was discussed. The electrolyte used in batteries was 1 mol/L LiPF₆-EC～DMC～EMC=1∶1∶1(in volume). The results showed that when the charging voltage is less than 2.5 V,  the main component of generated gases are H₂ and CO₂, and when the charging voltage is 2.5 V, EC begins to decompose. Due to the decomposition of EC, the main generated gas is C₂H₄ when the …

Application Of Hydrogen-Storage Alloy Electrode In Electrochemical Reduction Of Glucose, Hui Chen, You-Gen Tang, Zheng Tang

Journal of Electrochemistry

Electrolysis of glucose was performed at constant potential using hydrogen-storage alloy as catalytic reduction electrode. It was found that the superficial treatment and activation of hydrogen-storage alloy powder had obvious effects on improving the current efficiency of sorbitol. Under the optimums, current efficiency of sorbitol by electrolyzing glucose was over 94%. The yield of sorbitol was over 80%, the lifespan of electrode was tested and analyzed, the ways of regeneration were discussed.

Optimizing Catalyst Layer Composition Of Pemfc By Orthogonal Method, Ming-Hua Wang, Xin-Jian Zhu, Guang-Yi Cao, Sheng Sui, Qing-Chun Yu, Ming-Ruo Hu, Zheng-Yu Fan

Journal of Electrochemistry

The optimal composition of catalyst layer in a PEMFC electrode was studied through orthogonal method. It was showed that the performance of hydrophilic electrodes, in which there is no PTFE in the catalyst layer, were more favorable than that of hydrophobic electrodes. According to this condition, the power density of PEMFC attained 0.37 w·cm^-2 when the Nafion loading was 1.4 mg·cm^-2, and the Pt loading was 0.4 mg·cm^-2 in the catalyst layer, using H₂ as fuel and air as oxidant both at atmospheric pressure. Additionally, the results showed that increasing Pt loading in Pt/C catalyst …

The Study On Carbon Nanotube-Loaded Pt Catalysts For Proton Exchange Membrane Fuel Cells, Hong Zhu, Feng-Juan Ge, Xiao-Hong Kang, Yu-Guo Yang, Yun-Hua Xu

Journal of Electrochemistry

Carbon nanotube-supported-platinum (Pt/CNTs) and carbon-supported-platinum (Pt/C) catalysts were synthesized by in-situ chemical reduction. They were analyzed using TEM and XRD, then made into electrodes to be part of assemable PEMFC for the performence tests. The resulted show that Pt clusters in both catalysts are of small particle size (about 4nm), and Pt/CNTs exhibits a higher catalytic activity than Pt/C.

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge

Journal of Electrochemistry

Electrochemical oxidation of phenol was carried out by the Dimensionally Stable Anodes (DSA) electrode, which has been discarded as waste by alkali chloride factory. The result indicates that a good phenol removal can be obtained under certain phenol concentration by the DSA electrode. The key factor in effecting phenol removal of electrochemical oxidation is applied current density, the following factors are pH, electrolyte concentration and phenol concentration. After experiments, the optimal test conditions are 30 mA/cm², pH 10, electrolyte concentration 10 mg/L, phenol concentration 10 mg/L.67% CODcr removal and 90% absorbance removal are gained by electrochemical oxidation for …

The Current Fluctuations Of Carbon Steel In Nano2-Nacl Solutions, Yu-Ming Tang, Yu Zuo

Journal of Electrochemistry

The characteristics of current fluctuations of A3 carbon steel in NaNO₂-NaCl solutions were studied with potentiostatic and potentiodynamic polarization methods. The steel remained stable passivation in 0.1 mol/L NaNO₂ solution without Cl^-. After NaCl was added in to the solution, current fluctuations with a characteristic of quick increase and slow decrease occurred, indicating quick dissolution and slow re-passivation of the metastable pits. The metastable pitting may cause accumulated corrosion damage around certain area and result in observable pits. With the increase of chloride concentration, the occurring potential for metastable pits Em rised, and peak values …

Adsorption And Oxidation Of Phenol Electrode Processes, Bao-Cheng Wang, Yan-Ping Sun, Jin-Hua Zhu

Journal of Electrochemistry

The electrochemical behaviors of platinum electrode were studied by cyclic voltammetry in 1mol/L sulfuric acid solution and 1mol/L sulfuric acid solution contained phenol. The adsorption characteristics of phenol and the intermediat on electrode surface have been discussed. The reactive reversibility and oxidation mechanism of phenol on electrode process have been investigated.The potential of characteristic adsorption was suggested. The various products woud be formed when the electrode potential was greater than the one of characteristic adsorption.

Synthesis And Electrochemical Properties Of K2Feo4, Ning Zhou, Shi-Hai Ye, Yong-Long Wang, Xue-Ping Gao, Dong-Feng Lin, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The K₂FeO₄ used for new positive electrode materials was prepared. The primary batteries were used in different concentration of electrolyte and different currents. In 9 mol/L KOH , the capacity was the best. The higher the concentration of electrolyte, the lower the electric potential was. When the batteries discharged in 0.4 C , the capacity reached 521.3 mAh/g. By XRD, we gave the reasonable explanations for the discharge products of K₂FeO₄. Possible mechanism of discharge is discussed.

Synthesis Of Polyunit Vapor Phase Inhibitor And Its Volatile Corrosion Inhibition Performance, Da-Quan Zhang, Li-Xin Gao, Guo-Ding Zhou

Journal of Electrochemistry

A Mannich Base derivative (BMMCH), containing two morpholinum moieties and one cyclohexylamnonium moiety, was synthesized through aminomethy1 reaction. Its configuration was verified by IR and ¹H-NMR. Its volatile rustproofing effect was appraised by volatile rustproofing sieve test and vapor inhabitability test. The result shows that BMMCH has good protection effect for carbon steel. BMMCH has lower volatility compared with dicyclohexylamnonium nitrite (DICHAN) via closed space volatile weight-loss test. The inhibition mechanism was studied by potentiodynamic polarization electrochemistry technique in ASTM simulated atmospheric water. The corrosion potential of carbon steel electrode shifted to a negative direction when BMMCH was joined …

Comparison Of Thermal Cyclic Oxidation Of The Pvd Ni-Al And Hvof-Mcraly Coatings, J-T Chang, C-H Yeh, J-L He, K-C Chen

Journal of Electrochemistry

A PVD process-cathodic arc plasma ion plating was used to deposit Ni-Al films on Inconel 600 superalloy. The oxidation behaviors of PVD Ni-Al coating and the thermal sprayed CoCrAlY coatings were revealed and compared by performing cyclic thermal oxidation test at 1100 ℃ to evaluate its feasibility. Experimental results showed that the films with different compositions of Ni₆₂Al₃₈, Ni₆₃Al₃₇ and Ni₆₉Al₃₁ could be obtained when using Ni₅₂Al₄₈, Ni₆₀Al₄₀ and Ni₇₀Al₃₀ as targets, respectively. During the cyclic thermal oxidation test, the …

Effect Of Heat Laminating Aggregation Status Of Polymer Lithium-Ion Battery Cathode On Battery Performance, Ming-Gang Jin, Quan-Feng Dong, Ming-Sen Zheng, Li Huang, Hui-Qun Cai, Jin-Qua You, Zu-Geng Lin

Journal of Electrochemistry

Multi-layer heat laminated polymer lithium ion battery was made, the effect of temperature of cathode laminating on battry performance was also investigated. It was discovered that suitable temperature of cathode laminating is critical to battery performance and is a key parameter to manufacture process control of polymer lithium ion battery.

Electrochemistry And Electrocatalysis Of A Novel Μ-Oxamido Copper(Ⅱ) Binuclear Complex, Gui-Lian Gao, Guo-Bao Li, Qiu-Xia Yang, Xue-Lin Wang

Journal of Electrochemistry

In this paper, the cyclic voltammetric and spectroelectrochemical behaviors of μ-oxamido Copper(Ⅱ) Binuclear Complex (deCu) in PBS were studied. Cyclic voltammograms of this complex in PBS (pH=9) exhibited two reductive peaks (E_pc1 =-0.25 V, E_pc2 = -0.50 V) at hanging mercury drop electrode(HMDE), peaks at -0.50 V and -0.25 V corresponded to the reduction of ligand and copper(Ⅱ) complex, respectively. The spectroelectrochimical experiments showed that there was a new absorption band at 440 nm, and the absorption peaks at 270 nm, 280 nm red shifted to 300 nm, 310 nm under potential of -0.75 V. It was meant …

The Mechanism Of Electrocatalytic Reduction Of Oxygen On Manganese Dioxide, Yu-Liang Cao, Han-Xi Yang, Xin-Ping Ai, Li-Fen Xiao

Journal of Electrochemistry

The oxygen electroreduction on the MnO₂ electrode was investigated by analysis of the polarzation properties of oxygen reduciton and its dependence on MnO₂ discharge state, in combination with the characterization of discharge intermediate and the kinetic parameters of the oxygen reduction. Based on the experimental observation and mechanistic analysis, it was suggested that the reduction of oxygen was closely related to the discharge behaviors of MnO₂. When MnO₂ was electrochimically reduced to MnOOH, it was immediately oxidized by oxygen molecules. Thus the oxygen reduction proceeds through continuous oxidation of the discharge product of MnO_{2 …}

Day 5. Friday, August 15, 2003: Rocky Mountain National Park, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

1 page.

Contains references.

Day 4. Thursday, August 14, 2003: Hayden Power Plant, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

5 pages (includes color illustrations and maps).

Contains references.

Day 4. Thursday, August 14, 2003: Trapper Mine, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

8 pages (includes some color illustrations).

Contains references.

Day 3. Wednesday, August 13, 2003: Oil Shale, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

8 pages.

Contains references.

Day 3. Wednesday, August 13, 2003: Travel To Grand Junction, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

5 pages (includes color illustration and map).

Contains references.

Day 3. Wednesday, August 13, 2003: Lighthawk Flyover, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

11 pages (includes some color illustrations and maps).

Contains references.

Day 3. Wednesday, August 13, 2003: Coalbed Methane Development, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

10 pages (includes color illustrations and maps).

Day 2. Tuesday, August 12, 2003: Delta Montrose Energy, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

1 page.

Contains references.

Day 2. Tuesday, August 12, 2003: Valley Oil And Gas Development, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

1 page.

Contains references.

Day 1. Monday, August 11, 2003: National Renewable Energy Lab, National Energy Renewable Laboratory

Energy Field Tour 2003 (August 11-16)

8 pages (includes illustrations).

Contains references.

Agenda: Energy Field Tour 2003, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

Congressional staff tour held August 11-16, 2003

Summary: Binder of assorted articles, maps, brochures and other materials prepared for participants of the tour

Contents:

MONDAY, AUGUST 11, 2003: BLUE SPRUCE PEAKER PLANT: University of Colorado Natural Resources Law Center : congressional staff tour of Blue Spruce Energy Center / Peggy Duxbury -- 'Power Struggle', National Journal, June 27, 2003 / Margaret Kritz -- 'Calpine's Blue Spruce Energy Center begins commercial operation', Calpine press release, April 17, 2003 -- NATIONAL RENEWABLE ENERGY LAB: NREL at a glance -- NREL technologies -- SHOSHONE HYDROELECTRIC PLANT: 'River District Board supports spring Shoshone call …

Day 1. Monday, August 11, 2003: Shoshone Hydroelectric Plant, Glenwood Canyon, Shoshone Hydroelectric Plant

Energy Field Tour 2003 (August 11-16)

3 pages.

Contains references.

Day 1. Monday, August 11, 2003: Blue Spruce Peaker Plant, Blue Spruce Energy Center

Energy Field Tour 2003 (August 11-16)

10 pages (includes color illustrations and maps).

Contains references.

Monte Carlo Analysis Of Millimeter-Wave Gan Based Gunn Effect Oscillators, Sridhara Viswanadham

Electrical & Computer Engineering Theses & Dissertations

Gunn diodes are one of the most common high frequency solid-state oscillators at the present time, and are considered as promising devices for millimeter and submillimeter wave applications. Monte Carlo studies of Gunn diodes based on bulk wurtzite GaN have been carried out in this thesis research. Two structures have been examined: (i) devices with conventional single notch structure and (ii) repetitive structures with serial segments to fashion a "multiple domain" device. Wurtzite GaN has been chosen because of the high drift velocity and because analytical expressions for the band structure have recently become available. Performance parameters of interest such …

Oxidation Behavior Of Zr-Cu-Al-Ni Amorphous Alloys In Air At 300～500℃, H. H. Hsieh, W. Kai, T. G. Neih, Y. Kawamura

Journal of Electrochemistry

The oxidation behavior of the Zr- based bulk amorphous alloy (BMG; Zr-30Cu-10Al-5Ni in at.%) was studied in dry air over the temperature range 300～500 ℃. The kinetic results indicated that the amorphous alloy oxidized linearly at 300 ℃, while the parabolic oxidation was observed at 350～425 ℃, and the oxidation behavior at 500 ℃ was irregular and complicated. In general, the scales formed on the surface of the amorphous alloy were temperature-dependent, consisting of tetragonal-ZrO₂ at 300 ℃, and of mostly tetragonal-ZrO₂ as well as minor amounts of monoclinic-ZrO₂ and CuO at T ≥ 350 ℃.