Power and Energy Commons^™

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Analysis Of Three-Phase Rectifier Via Three Different Control Methods And Switch Power Loss Comparison, Yichao Wang

All Graduate Theses, Dissertations, and Other Capstone Projects

Traditional uncontrolled or phase-controlled rectifiers have the defects of lower power factor and nontrivial higher harmonics which causes the low efficiency of power, bad power quality, and so on. However, PWM rectifiers overcome the drawbacks mentioned above. They reduce the higher harmonics yielding better sinusoidal current on the grid side, achieve unity power factor and bidirectional power flow, and have better dynamic performance. So, it is favored more by academia and widely applied in high-performance power electronics devices. In this paper, the PWM rectifier is analyzed and a comparison of the switch loss on three-phase rectifier using three different control …

Ball Oscillating Bouncer, Eric Blok, Daniel Altemese, Ryan Nowacki, Maram Qurban

Williams Honors College, Honors Research Projects

The purpose of this report is to document the need, objectives, marketing and engineering requirements, as well as validate the design of an autonomous control device capable of continuously bouncing a table tennis ball on a paddle. This includes the design of a self correcting system using lightweight materials, and as few sensors and components as possible to achieve a compact, portable design. To accomplish this, the system is designed to react to a ball falling from as short a distance as 10 centimeters above the paddle, meaning all sensor processing, control processing, and motor drives should be able to …

Automatic Water Pump Controller, Alam D. Salguero, Kyle Russell Marquez Weeks

Electrical Engineering

In countries including Indonesia, Mexico, Guatemala, and El Salvador, a city water authority supplies the clean water and pumps it into large ground-level storage tanks. A resident’s water pump then pumps the water to a water tank on top of his/her house. When the water level in the ground-level storage tank becomes too low, the pump siphons air and shuts down, requiring a resident to manually prime the water pump to get it running again. Residents struggle to monitor the water level of the tanks effectively and keep the pump running properly. To remedy the issue, the Automatic Water Pump …

Polar Field Oriented Control With 3rd Harmonic Injection, Martin Todd Hess

Master's Theses

Abstract

POLAR FIELD-ORIENTED CONTROL

with

3^RD HARMONIC INJECTION

Martin Todd Hess

Field Oriented Control (FOC), also known as vector control, is a widely used and well documented method for controlling Permanent-Magnet Synchronous Motors (PMSM) and induction motors. Almost invariably the orientation of the stator and rotor (field) fluxes are described in rectangular coordinates. In this thesis we explore the practicality of using polar coordinates.

Third harmonic injection is also a well-known technique that allows full utilization of the bus (DC-link), thus allowing the motor to run to full base speed without the use of field weakening. This technique potentially …

Standardised Control Techniques For Induction Generators In Both Grid-Connected And Isolated Applications, John Brazil, Aidan O'Dwyer, M. Murphy

Conference papers

Induction generators are particularly suitable for small hydro applications and are widely used at present. However, with conventional grid-connected techniques, it is not always possible to use them in regions with weak grids because of excessive connection transients. Consequently, their many advantages cannot be fully exploited in these regions. Standardised control systems have been developed by ECS for isolated applications of induction generators and these will now be further developed to permit reduced-transient grid connections.