Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Keyword
-
- Tensile strength (11)
- Mechanical properties (6)
- Microstructure (6)
- Simulation (6)
- Activated carbon (5)
-
- Bacterial cellulose (5)
- Biodiesel (5)
- CFD (5)
- Composite (5)
- Performance (5)
- Surface roughness (5)
- Hardness (4)
- Material (4)
- Pyrolysis (4)
- SEM (4)
- Temperature (4)
- ANSYS (3)
- Biocomposite (3)
- Bioethanol (3)
- Bioplastic (3)
- Cassava starch (3)
- Efficiency (3)
- Energy efficiency (3)
- FEA (3)
- FTIR (3)
- Heat treatment (3)
- Morphology (3)
- Permeability (3)
- Roughness (3)
- Surface (3)
- Publication Year
Articles 1 - 30 of 185
Full-Text Articles in Computational Engineering
Structural Design And Finite Element Analysis Of A 54 Ton Freight Wagon Bolster Test Rig Under Vertical Center Plate Load, Shandy Dwi Prayoga, I Dewa Gede Ary Subagia, I Ketut Adi Atmika, Abdul Rohman Farid, Yunior Lanang Satrio
Structural Design And Finite Element Analysis Of A 54 Ton Freight Wagon Bolster Test Rig Under Vertical Center Plate Load, Shandy Dwi Prayoga, I Dewa Gede Ary Subagia, I Ketut Adi Atmika, Abdul Rohman Farid, Yunior Lanang Satrio
Journal of Mechanical Engineering Science and Technology (JMEST)
Bolster is one of the bogie's components that receives direct loading from the car body and freight movement. One of the problems that occurs in the bolster is permanent deflection during vertical and transversal static loading. Therefore, a static loading test is required to evaluate the structural strength of the bolster. During the static loading test, a rig is required to hold the bolster so that the bolster is in a fixed position. The rig owned by PT. INKA (Persero) showed a plastic deformation at the vertical center plate load (VCP 5.22P). Therefore, a modified design of the rig is …
Numerical Simulation Of Centrifugal Pump Performance Under Impeller Blade And Suction Diameter Variations, Gunawan Budi Santoso, Susanto -, Akhmad Nuriyanis, Anang Budhi Nugroho, Rizka Noor Miftakhul Ulum, Suyono -
Numerical Simulation Of Centrifugal Pump Performance Under Impeller Blade And Suction Diameter Variations, Gunawan Budi Santoso, Susanto -, Akhmad Nuriyanis, Anang Budhi Nugroho, Rizka Noor Miftakhul Ulum, Suyono -
Journal of Mechanical Engineering Science and Technology (JMEST)
The objective of this study is to model variations in pump geometry to obtain optimal performance under the effects of cavitation. The resulting geometric variation models were then simulated using ANSYS Fluent software. The first geometric variation model used a standard 5-blade impeller with suction pipe diameter variations of 2, 2 ½, 2 ¾, 3, 3 ¼, 3 ½, and 4 inches. The second geometric variation model for simulation used a standard 3-inch suction pipe with impeller blade variations of 3, 4, 5, 6, 7, 8, and 9. The simulation results indicated that the number of blades without changes in …
Effect Of Naoh Concentration On The Structural, Morphological, And Tensile Properties Of Pineapple Stem Fibers, Ahmad Norca Kurnia Zen, Heru Suryanto, Aminnudin Aminnudin, Fajar Nusantara, Joseph Selvi Binoj
Effect Of Naoh Concentration On The Structural, Morphological, And Tensile Properties Of Pineapple Stem Fibers, Ahmad Norca Kurnia Zen, Heru Suryanto, Aminnudin Aminnudin, Fajar Nusantara, Joseph Selvi Binoj
Journal of Mechanical Engineering Science and Technology (JMEST)
Natural fiber reinforced composites are increasingly being developed due to their environmentally friendly nature, low production costs, and safety for human health. However, the presence of lignin and hemicellulose reduces adhesion properties between fiber and composite matrix. Alkalization treatment is an effective way to remove lignin and hemicellulose attached to cellulose. This study aims to determine the optimum concentration of NaOH used during alkalization process of pineapple stem fiber. The methods included the retting process of fibers from pineapple stems. The obtained fibers were soaked in variations of 2%, 4%, 6%, and 8% NaOH for 4 hours, then dried and …
Optimization And Energy Efficiency Analysis Of An Automatic Feed Mixer With A Rotating Drum Mechanism, Kris Witono, Talifatim Machfuroh, Nurlia Pramita Sari, Lisa Agustriyana, Aini Lostari
Optimization And Energy Efficiency Analysis Of An Automatic Feed Mixer With A Rotating Drum Mechanism, Kris Witono, Talifatim Machfuroh, Nurlia Pramita Sari, Lisa Agustriyana, Aini Lostari
Journal of Mechanical Engineering Science and Technology (JMEST)
Energy-efficient feed mixer machines are important for improving the productivity and sustainability of small and medium-scale livestock farms. Previous studies primarily focused on either structural performance or mixing efficiency, with limited studies integrating both aspects. Therefore, this study evaluated an automatic rotating-drum feed mixer by combining Finite Element Method (FEM) analysis and energy modeling. The study used FEM simulations for different materials, namely A36 steel alloy, stainless steel 304, aluminium 6061, and galvanized steel, with thicknesses of 3 mm and 4 mm, as well as different drum systems. The FEM results showed that all evaluated materials met the minimum safety …
Influence Of Gas Atmosphere And Deposition Time On Si/Mno₂ Thin Films Properties Deposited By Magnetron Sputtering For Supercapacitor Application, Tansya Trisnatika Dewi, Boon Tong Goh, Reza Akbar Pahlevi, Ishmah Luthfiyah, Markus Diantoro
Influence Of Gas Atmosphere And Deposition Time On Si/Mno₂ Thin Films Properties Deposited By Magnetron Sputtering For Supercapacitor Application, Tansya Trisnatika Dewi, Boon Tong Goh, Reza Akbar Pahlevi, Ishmah Luthfiyah, Markus Diantoro
Journal of Mechanical Engineering Science and Technology (JMEST)
Thin films of MnO2 were successfully deposited onto Si substrates using the magnetron sputtering technique in various gas atmospheres and deposition times to study their influence on the structural, morphological, electrical, and electrochemical properties for application as supercapacitor electrodes. Structural analysis using XRD showed that deposition under an Ar+O2 gas atmosphere increased the crystallite size and crystallinity of the Si/MnO2 films, while shorter deposition times reduced the crystallite size and lowered the crystallinity. Surface morphology observation using SEM showed that the film deposited in an Ar+O2 gas atmosphere had smaller, more uniform, evenly distributed, and closely …
Influence Of Fiber Loading And Cu/Sio₂ Fillers On Mechanical And Physical Properties Of Sugarcane Bagasse Epoxy Composites, Ansor Salim Siregar, Indra Indra, Agung Fauzi Hanafi, Sunny Ineza Putri
Influence Of Fiber Loading And Cu/Sio₂ Fillers On Mechanical And Physical Properties Of Sugarcane Bagasse Epoxy Composites, Ansor Salim Siregar, Indra Indra, Agung Fauzi Hanafi, Sunny Ineza Putri
Journal of Mechanical Engineering Science and Technology (JMEST)
The rising worldwide need for lightweight, high-strength, and eco-friendly materials has driven considerable investigation into natural fiber composites. This research offers an extensive examination of the creation and characterization of a new hybrid composite designed for high-performance sports equipment. The composite structure consists of an epoxy matrix strengthened with sugarcane bagasse fibers and synergistic blend of copper and silicon dioxide hybrid particulate fillers. Three unique composite variations were created, with systematically adjusted weight fractions of sugarcane bagasse fiber (35%, 31%, 27%) and hybrid fillers. A thorough assessment of mechanical and physical properties was carried out following ASTM standards. The results …
Spray Angle On The Performance Of Split-Type Ac Condenser Installed On Concrete Rooftop In Tropical Climate, Kennedy Kennedy, I N Frenki Aryana, Basri Basri
Spray Angle On The Performance Of Split-Type Ac Condenser Installed On Concrete Rooftop In Tropical Climate, Kennedy Kennedy, I N Frenki Aryana, Basri Basri
Journal of Mechanical Engineering Science and Technology (JMEST)
This study investigated the influence of different water spray angles (0°, 15°, and 30°) on the thermal and energy performance of a split-type air-conditioning (AC) condenser installed on a concrete rooftop in a tropical climate. An experimental setup was designed to replicate actual concrete rooftop conditions, focusing on the condenser inlet temperature, compressor power consumption, and system coefficient of performance (COP). A 6-minute ON and 6-minute OFF intermittent spray cycle was employed to optimise water usage and minimise excessive humidity. Experimental measurements were conducted on a 9,000 Btu/h split-type unit equipped with a nozzle system connected to a 200 L …
Effect Of Argon Gas Flow Rate On Crystal Structure, Morphology, And Optical Properties Of Cigs Film For Photodetector Applications, Nurul Lathi’I Fatul Chamidah, Fadilah Wulan Cahyani, I Gusti Ayu Isnaini Fatha Ramadhani, Erma Surya Yuliana, Nasikhudin Nasikhudin, Safwan Abd. Aziz, Nandang Mufti
Effect Of Argon Gas Flow Rate On Crystal Structure, Morphology, And Optical Properties Of Cigs Film For Photodetector Applications, Nurul Lathi’I Fatul Chamidah, Fadilah Wulan Cahyani, I Gusti Ayu Isnaini Fatha Ramadhani, Erma Surya Yuliana, Nasikhudin Nasikhudin, Safwan Abd. Aziz, Nandang Mufti
Journal of Mechanical Engineering Science and Technology (JMEST)
CIGS material can be used as a material for photodetector applications. The deposition of CIGS thin films remains challenging. Generally, argon is used as a gas to bombard the CIGS material through the sputtering method. This study fabricated photodetectors by varying the argon gas flow rate (50-80 sccm) to investigate its effect on device performance. XRD, SEM, UV-Vis, and photoresponse tests were characterized. Structural analysis using XRD showed a weak (112) diffraction peak, indicating that the resulting film was not fully crystalline, but rather consisted of a nanocrystalline phase, even partly amorphous, with small crystallite sizes. According to the SEM …
Numerical Analysis Of The Effect Of Vortex Generator On The Aerodynamic Performance Of Naca 6412 Airfoils Using Large Eddy Simulation, Dedet Hermawan Setiabudi, Joan Bayuaji Nugroho, Eli Kumolosari, Lazuardy Rahendra Pinandhita, Okto Dinaryanto
Numerical Analysis Of The Effect Of Vortex Generator On The Aerodynamic Performance Of Naca 6412 Airfoils Using Large Eddy Simulation, Dedet Hermawan Setiabudi, Joan Bayuaji Nugroho, Eli Kumolosari, Lazuardy Rahendra Pinandhita, Okto Dinaryanto
Journal of Mechanical Engineering Science and Technology (JMEST)
Aerodynamic performance of an airfoil is significantly affected by flow separation, especially at high angles of attack. One common strategy to control flow separation is adding a triangular vortex generator (VG), which creates small vortices that help keep the airflow attached. The present study investigated the impact of triangular vortex generators on a NACA 6412 airfoil using Computational Fluid Dynamics (CFD) method. Large Eddy Simulation (LES) was applied due to its ability to show the vortices more clearly than other methods. It can also accurately capture the flow separation. To obtain the lift, drag, and lift-to-drag ratio (CL/CD) data, four …
Impact Of Cpo And B35 On Diesel Engine Rocker Arm Wear During Long-Term Operation, Fawwaz Aqilah Nurmansyah, Nur Fadilah Rizky Supramono, Muhammad Ikhsan, Erwan Adi Saputro, Wiliandi Saputro
Impact Of Cpo And B35 On Diesel Engine Rocker Arm Wear During Long-Term Operation, Fawwaz Aqilah Nurmansyah, Nur Fadilah Rizky Supramono, Muhammad Ikhsan, Erwan Adi Saputro, Wiliandi Saputro
Journal of Mechanical Engineering Science and Technology (JMEST)
The increasing number of motor vehicles has led to higher fossil fuel consumption, contributing to greenhouse gas emissions, climate change, and environmental degradation. As a renewable alternative, biodiesel offers a way to reduce these impacts. Indonesia, with its abundant natural resources, has significant potential for biodiesel production. Crude palm oil (CPO) is a promising feedstock due to its availability and relatively low environmental impact. However, the high costs associated with the transesterification process make direct use of pre-heated CPO an area worth exploring. This study investigates the impact of pre-heated pure CPO compared to B35 ("Dexlite") on rocker arm wear …
The Effect Of Heat Treatment Duration On The Psychochemical, Mechanical, And Biodegradability Of Polyvinyl Alcohol/Gambir Extract Biocomposite Films, Ainul Kahfi Muhlasin, Poppy Puspitasari, Heru Suryanto, Diki Dwi Pramono, Dieter Rahmadiawan, Billie Jack Pasion
The Effect Of Heat Treatment Duration On The Psychochemical, Mechanical, And Biodegradability Of Polyvinyl Alcohol/Gambir Extract Biocomposite Films, Ainul Kahfi Muhlasin, Poppy Puspitasari, Heru Suryanto, Diki Dwi Pramono, Dieter Rahmadiawan, Billie Jack Pasion
Journal of Mechanical Engineering Science and Technology (JMEST)
This study investigates PVA-based films with the addition of gambir and heat treatment to improve the characteristics of the film. Methods include the synthesis of PVA film with gambir addition (0.5%), treated by heat treatment for 40 minutes and 60 minutes. The film was characterised by physicochemical, mechanical properties, and biodegradability. Data was analyzed using ANOVA with a significance of 95%. Results indicate that the surface of PVA/gambir films is smoother and more homogeneous as the heat treatment duration increases. New peaks of functional groups were identified after the addition of gambir at the C-C and C-O groups. After heat …
Surface Modification Of Local Natural Fibers Via Alkali Treatment For Improved Mechanical And Molecular Properties Of Bamboo Fiber, Pineapple Leaf Fiber, And Sisal Fiber, Jibril Maulana, Muhammad Ilman Nur Sasongko, Dewi Izzatus Tsamroh, Muchammad Yafis, Syekhan Maulana
Surface Modification Of Local Natural Fibers Via Alkali Treatment For Improved Mechanical And Molecular Properties Of Bamboo Fiber, Pineapple Leaf Fiber, And Sisal Fiber, Jibril Maulana, Muhammad Ilman Nur Sasongko, Dewi Izzatus Tsamroh, Muchammad Yafis, Syekhan Maulana
Journal of Mechanical Engineering Science and Technology (JMEST)
A major development in materials science toward reinforcement materials in biopolymer composites has been caused by a worldwide trend toward sustainable manufacturing and the rise of the circular economy. However, their mechanical properties can often be affected by their hydrophilic properties, lack of surface compatibility, and their presence of molecular bonding, such as lignin and hemicellulose. Alkaline surface modification has been widely reported as an effective technique to increase structural stability and fibermatrix adhesion. This study evaluated the effects of alkalizing three types of local natural fibers—bamboo fiber (BF), pineapple leaf fiber (PALF), and sisal (SF)—with sodium hydroxide (NaOH) at …
Thermophysical, Rheological And Wear Resistance Of Canola Oil Biolubricant With Calcium Carbonate Additive Nanoparticle As Coolant In Cnc Machining, Alfandi Jaelani, Poppy Puspitasari, Diki Dwi Pramono, Alief Muhammad, Muhammad Kozin, Muhammad Kashif
Thermophysical, Rheological And Wear Resistance Of Canola Oil Biolubricant With Calcium Carbonate Additive Nanoparticle As Coolant In Cnc Machining, Alfandi Jaelani, Poppy Puspitasari, Diki Dwi Pramono, Alief Muhammad, Muhammad Kozin, Muhammad Kashif
Journal of Mechanical Engineering Science and Technology (JMEST)
Vegetable oil-based cutting fluids are of great importance in supporting green and sustainable manufacturing. This research introduces a new groundbreaking vegetable lubricant formulated with canola oil as the base material, coupled with CaCO3 nanoparticles synthesized from scallop shell waste and used as a cutting fluid in the AISI 1045 CNC machining process steel sprayed with minimum quantity lubrication (MQL). This investigation delves into the thermophysical, rheological, and wear resistance of the developed bio-lubricant. The results of this analysis show density value increased in the canola + CaCO3 0.15% sample by 3.28% of the pure canola sample, as did the viscosity …
Improvement Of Thermal Energy Storage Performance In Al-Al2o3 Composites Through Additions Of Copper: Evaluation Of Microstructure And Thermal Properties, Muhammad Hasan Basri, Ramang Magga, Muhammad Syaiful Fadly, Zikri Arifansyah Djaba, Muhammad Iqbal Ibrahim, Hidayat Hidayat, Yandi Yandi
Improvement Of Thermal Energy Storage Performance In Al-Al2o3 Composites Through Additions Of Copper: Evaluation Of Microstructure And Thermal Properties, Muhammad Hasan Basri, Ramang Magga, Muhammad Syaiful Fadly, Zikri Arifansyah Djaba, Muhammad Iqbal Ibrahim, Hidayat Hidayat, Yandi Yandi
Journal of Mechanical Engineering Science and Technology (JMEST)
The study aims to evaluate the influence of adding copper aluminum–alumina composite (Al–Al₂O₃) against characteristic thermal properties through metallurgical powder. Three variations of the composition of weight copper were used, namely 5%, 10%, and 15%, with aluminum as the matrix and alumina as the reinforcement. Thermal test covering analysis of thermal conductivity, specific heat, and microstructure characterization using SEM-EDX. The results show that adding Cu increases thermal conductivity significantly, with the highest mark achieved in the 15% Cu composite (6.47 W/m.°C). However, the increase in Cu content above 10% causes the agglomeration of particles and enhancements in porosity, which harms …
Optimizing Zeolite Catalysts For Efficient Ldpe Plastic Waste Pyrolysis, Hilda Porawati, Mazwan Mazwan, Sukadi Sukadi
Optimizing Zeolite Catalysts For Efficient Ldpe Plastic Waste Pyrolysis, Hilda Porawati, Mazwan Mazwan, Sukadi Sukadi
Journal of Mechanical Engineering Science and Technology (JMEST)
The problem of plastic waste, particularly from low-density polyethylene (LDPE) plastic bags, poses a significant challenge in environmental management due to its non-biodegradable nature and widespread use in daily life. This study evaluates the influence of catalyst types on the characteristics and energy efficiency of liquid fuel products produced from LDPE waste pyrolysis. The three treatments compared were no catalysts, natural zeolite catalyst, and synthetic zeolite catalysts, each subjected to three different temperature variations: 250°C, 300°C, and 350°C. The observed parameters in this study were volume, product mass, cetane index, density, sulfur content, viscosity, flash point, calorific value, and energy …
The Impact Of Pine Resin-Epoxy Ratios On Fire Resistance And Acoustic Performance Of Banana Fiber Composites, Cokorda Istri Putri Kusuma Kencanawati, Dewa Ngakan Ketut Putra Negara, I Gede Andy Andika Parahita
The Impact Of Pine Resin-Epoxy Ratios On Fire Resistance And Acoustic Performance Of Banana Fiber Composites, Cokorda Istri Putri Kusuma Kencanawati, Dewa Ngakan Ketut Putra Negara, I Gede Andy Andika Parahita
Journal of Mechanical Engineering Science and Technology (JMEST)
Because of their low environmental impact and biodegradability, composite materials derived from natural fibers and resins have drawn interest as sustainable substitutes for synthetic materials in thermal and acoustic applications. Two promising natural components are banana stem fiber and pine resin, but they need to be modified due to their mechanical limitations and flammability. Epoxy resin is commonly used to enhance structural performance; however, its effects on acoustic and fire resistance properties require further investigation. This study examined how different epoxy resin contents affected the sound absorption and fire resistance of composites made from banana stem fiber and pine resin. …
Simulation Of Stress, Deformation, And Vibration In Unlubricated Ball Bearings At Varying Rotational Speeds, Billy Dwiki, Moh. Hartono
Simulation Of Stress, Deformation, And Vibration In Unlubricated Ball Bearings At Varying Rotational Speeds, Billy Dwiki, Moh. Hartono
Journal of Mechanical Engineering Science and Technology (JMEST)
Bearings are critical components in rotating machinery, and their performance is highly influenced by operational factors such as rotational speed, load, and lubrication. This study aims to analyze the deformation, stress, and dynamic behavior of SAE 52100 bearings under dry operating conditions at various rotational speeds, as well as to propose mitigation strategies for high-speed industrial applications. A finite element simulation was conducted using ANSYS R19.2 to evaluate the total deformation, equivalent elastic strain, Von Mises stress, and vibrational characteristics of a 6204-type SAE 52100 bearing. The simulations were performed across a speed range of 600 to 2000 RPM under …
Numerical Investigation Of Ethanol-Enriched Diesel And Biodiesel Fuels In A Diesel Engine, Annisa Bhikuning, Hezron Elyakim Potto, Sandi Apriandi Setiawan, Jamal F. Jati
Numerical Investigation Of Ethanol-Enriched Diesel And Biodiesel Fuels In A Diesel Engine, Annisa Bhikuning, Hezron Elyakim Potto, Sandi Apriandi Setiawan, Jamal F. Jati
Journal of Mechanical Engineering Science and Technology (JMEST)
This study explores the effects of ethanol blending on the performance and emissions of a compression ignition (CI) engine using both diesel and biodiesel as base fuels. Motivated by increasing environmental concerns regarding pollutant emissions from conventional diesel engines, ethanol was introduced as an oxygenated additive to improve combustion characteristics and reduce the formation of harmful exhaust emissions. Ethanol’s high oxygen content promotes more complete combustion, potentially lowering carbon-based emissions such as carbon monoxide (CO), particulate matter (PM), and unburned hydrocarbons. In this study, performance and emission parameters were simulated using Diesel-RK software at various engine speeds of 1500, 2000, …
One-Way Thermal-Fluid-Solid Coupling Analysis Of Helicopter Tail Reducer With Spiral Bevel Gear, Dongping Sheng, Zhongyuan Ma, Chenqi Zhou, Haidong Feng, Hun Guo, Chun Su
One-Way Thermal-Fluid-Solid Coupling Analysis Of Helicopter Tail Reducer With Spiral Bevel Gear, Dongping Sheng, Zhongyuan Ma, Chenqi Zhou, Haidong Feng, Hun Guo, Chun Su
Journal of Mechanical Engineering Science and Technology (JMEST)
This research focuses on investigating the thermal-fluid-solid coupling behavior within spiral bevel gears to enhance the bearing capacity and extend the operational service life of the gear reducer located in the helicopter tail gearbox. The study commences by constructing detailed, parametrically defined threedimensional digital models. These models accurately represent the critical components: the spiral bevel gear itself, the surrounding gearbox housing, and the supporting gear shaft, based directly on the specifications of an actual helicopter tail reducer assembly. Subsequently, the analysis proceeds with a one-way, steadystate thermal-solid coupling simulation performed on the established model assembly. This critical simulation phase aims …
The Effect Of Preheater On Heat And Mass Transfer Efficiency Using Rotating Drum Roaster, Melisa Surya Andini, Retno Wulandari, Heru Suryanto
The Effect Of Preheater On Heat And Mass Transfer Efficiency Using Rotating Drum Roaster, Melisa Surya Andini, Retno Wulandari, Heru Suryanto
Journal of Mechanical Engineering Science and Technology (JMEST)
Indonesia is the third-largest coffee producer globally, facing challenges including rising raw material costs, increased energy consumption, and unpredictable weather conditions. One potential solution is optimizing energy efficiency during roasting. This study investigates the effect of preheating on time and energy efficiency in heat and mass transfer by utilizing waste heat to preheat green Robusta coffee beans. The experiment was conducted on a laboratory scale using a rotating drum roaster with a double-layer drum made of stainless steel and clay, at 200 °C under atmospheric pressure. Two treatments were applied: roasting with a preheater and without, each repeated three times …
Analysis Of Engine Parameters Of High Composition Palm Oil Biodiesel In Crdi System, Achmad Aminudin, Kelvin Dwi Wardana, Nanang Romandoni, Ahmad Yusril Aminullah, Nur Ihda Farikhatin Nisa, Hari Setiapraja
Analysis Of Engine Parameters Of High Composition Palm Oil Biodiesel In Crdi System, Achmad Aminudin, Kelvin Dwi Wardana, Nanang Romandoni, Ahmad Yusril Aminullah, Nur Ihda Farikhatin Nisa, Hari Setiapraja
Journal of Mechanical Engineering Science and Technology (JMEST)
The heavy reliance on fossil fuels has serious consequences, particularly regarding increased greenhouse gas emissions that contribute to global warming. In order to obtain cleaner fuel resources and reduce fossil fuel dependence, palm oil biodiesel is added to fossil diesel by volume ratio resulting in B50 and B55 blends. Combustion characteristics, performance, fuel consumption, and emissions were performed in a diesel engine with a 4-cylinder common rail direct injection (CRDI) at different engine speeds (1500, 2000, 2500, and 3000 rpm). Compared to fossil diesel, biodiesel blends exhibit higher density at 855.9 kg/m³ (B55), kinematic viscosity with a value of 5.1 …
Utilization Of Biomass From Kerai Payung Trees And Waste Paper Through Pyrolysis Technology To Support The Zero-Waste Concept, Anggita Putri Indadari, Nurfa Anisa, Asih Budi Santoso
Utilization Of Biomass From Kerai Payung Trees And Waste Paper Through Pyrolysis Technology To Support The Zero-Waste Concept, Anggita Putri Indadari, Nurfa Anisa, Asih Budi Santoso
Journal of Mechanical Engineering Science and Technology (JMEST)
Wisnuwardhana University is a private institution with a green campus environment surrounded by Kerai Payung trees. This environment produces organic waste from trees and inorganic waste such as used paper from campus activities. This study aims to achieve zero-waste processing by using pyrolysis technology to process campus waste, ensuring minimal residue. The experimental method involves comparing waste processing outcomes between conventional combustion and pyrolysis, the data was analyzed by comparing the results of pyrolysis with conventional combustion. The results of biochar from the pyrolysis process of used paper, Kerai Payung leaves, and nagging Kerai Payung tree are 76 g, 250 …
Dynamic Analysis And Fatigue Life Evaluation Of Single Herringbone Planetary Gear System With Crack Fault, Dongping Sheng, Jie Yang, Chun Su
Dynamic Analysis And Fatigue Life Evaluation Of Single Herringbone Planetary Gear System With Crack Fault, Dongping Sheng, Jie Yang, Chun Su
Journal of Mechanical Engineering Science and Technology (JMEST)
The herringbone planetary gear transmission is widely used due to its exquisite compact structure, excellent load-bearing capacity, and stable transmission characteristics. However, root crack is one of the most common failure modes of gears. A cracked herringbone planetary gear system is taken as research object. The sun gear with crack fault is studied from the aspect of modal and transient dynamic analysis, and the related results are compared with the healthy gear. Based on the transient dynamic analysis of the herringbone teeth with cracks, a fatigue life evaluation is conducted. Firstly, the results show that no significant difference between the …
Investigation Of Drag Force And Downforce On Two Racing Motorcycles In Slipstream Conditions, Muhamad Hanifudin, Gaguk Jatisukamto, Mahros Darsin, Muh. Nurkoyim Kustanto, Azmi Saleh, Suprihadi Prasetyono, Catur Suko Sarwono
Investigation Of Drag Force And Downforce On Two Racing Motorcycles In Slipstream Conditions, Muhamad Hanifudin, Gaguk Jatisukamto, Mahros Darsin, Muh. Nurkoyim Kustanto, Azmi Saleh, Suprihadi Prasetyono, Catur Suko Sarwono
Journal of Mechanical Engineering Science and Technology (JMEST)
The performance of modern racing motorcycles is greatly influenced by their aerodynamics. Slipstreaming occurs during a race when a rider closely follows another, especially on a straight track. The effect can reduce aerodynamic drag and increase the overall speed of the rider behind. This study investigates the aerodynamic effects of slipstreaming on a racing motorcycle using computational fluid dynamics. This study also considers its effect on both drag force and downforce, which affects motorcycle stability. A 3D CAD model of a racing motorcycle and a rider in a crouching position was used as the object of research. CFD simulations were …
Characterization Of Curcumin As A Coating Material For Polymer-Free Stents Interms Of Morphology And Release, Ameliyana R.S.P.A. Yani, Muhammad Kusumawan Herliansyah
Characterization Of Curcumin As A Coating Material For Polymer-Free Stents Interms Of Morphology And Release, Ameliyana R.S.P.A. Yani, Muhammad Kusumawan Herliansyah
Journal of Mechanical Engineering Science and Technology (JMEST)
The use of bare metal stents over the long term often leads to the re-narrowing of blood vessels, prompting a shift to drug-eluting stents (DES). However, the use of polymers in DES has been known to trigger inflammation and thrombosis in the arteries. As an alternative, polymer-free drug-eluting stents (PF-DES) have emerged as a safer option. In this study, curcumin was selected as the primary coating material for PFDES using the electrophoretic deposition method. The effects of varying curcumin concentrations (125 µg/ml, 250 µg/ml, and 500 µg/ml) were examined to understand their impact on deposition morphology, coating weight, chemical bonding …
Influence Of Different Nanoparticles On Thermophysical Properties And Wear Resistance Of Corn Oil-Based Cutting Fluid In Mql-Cnc Milling Machining, M Nuril Anwar Habiby, Poppy Puspitasari, Aminnudin Aminnudin, Diki Dwi Pramono, Ahmad Atif Fikri, Mariyam Jameelah Ghazali
Influence Of Different Nanoparticles On Thermophysical Properties And Wear Resistance Of Corn Oil-Based Cutting Fluid In Mql-Cnc Milling Machining, M Nuril Anwar Habiby, Poppy Puspitasari, Aminnudin Aminnudin, Diki Dwi Pramono, Ahmad Atif Fikri, Mariyam Jameelah Ghazali
Journal of Mechanical Engineering Science and Technology (JMEST)
Vegetable oil-based cutting fluids have emerged as a promising innovation in machining operations, supporting the advancement of sustainable and eco-friendly manufacturing practices. This study delves into the development of a biolubricant derived from corn oil, enriched with 0.15% mass fractions of various nanoparticles, including calcium carbonate (CaCO3), copper oxide (CuO), and multi-walled carbon nanotubes (MWCNT). These nano-cutting fluids were applied through the Minimum Quantity Lubrication (MQL) method during CNC milling of AISI 1045 steel. The investigation focused on evaluating thermophysical properties, including density, thermal conductivity, and dynamic viscosity, as well as tool wear performance. The results demonstrated that CuO nanoparticles …
Impact Of Print Speed And Nozzle Temperature On Tensile Strength Of 3d Printed Abs For Permanent Magnet Turbine Systems, Wirawan Wirawan, Hilmi Iman Firmansyah, Satworo Adiwidodo, Mohammad Sukri Mustapa
Impact Of Print Speed And Nozzle Temperature On Tensile Strength Of 3d Printed Abs For Permanent Magnet Turbine Systems, Wirawan Wirawan, Hilmi Iman Firmansyah, Satworo Adiwidodo, Mohammad Sukri Mustapa
Journal of Mechanical Engineering Science and Technology (JMEST)
Operational parameters must be integrated into turbine systems' main components, which are determined by turbine systems' functional requirements. The need for producing component designs more effectively raises the possibility of using additive manufacturing. The study focuses on the optimization of the mechanical properties of the principal components of magnetic turbines manufactured with 3D printers using Acrylonitrile Butadiene Styrene (ABS), by changing the temperature and speed of the nozzle. The approach consisted of modeling a standard test piece in CAD software and producing ABS-based test pieces using a 3D printer with print speeds of 50, 70, 90, and 110 mm/s and …
Performance Analysis Of Alkaline Fuel Cell With Variation Of Potassium Hydroxide Concentration In Electrolyte Solution, Mohammad Rifqy Alfariz, Nasrul Ilminnafik, Dwi Djumhariyanto, Intan Hardiatama, Muhammad Khadafi Ibnu, Raafi Aditya Nugraha, Domingos De Sousa Freitas
Performance Analysis Of Alkaline Fuel Cell With Variation Of Potassium Hydroxide Concentration In Electrolyte Solution, Mohammad Rifqy Alfariz, Nasrul Ilminnafik, Dwi Djumhariyanto, Intan Hardiatama, Muhammad Khadafi Ibnu, Raafi Aditya Nugraha, Domingos De Sousa Freitas
Journal of Mechanical Engineering Science and Technology (JMEST)
Alkaline Fuel Cell (AFC) is a green energy conversion tool that converts chemical energy into electrical energy through electrochemical reactions. This research aims to analyze the effect of potassium hydroxide (KOH) concentration variation in electrolyte solution on the AFC performance, using nickel and manganese catalysts. The research methods include experiments using various KOH concentrations to determine the optimal concentration to produce the best AFC performance. The voltage and current produced are measured, as well as the calculation of the electrical power and efficiency of the AFC. The results showed that KOH concentration has a significant influence on the performance of …
Toolpath Motion Strategy And Feed Rate In Cnc Milling On Energy Consumption Of Machining Process, Luqman Dwi Saputra, Eko Yudiyanto
Toolpath Motion Strategy And Feed Rate In Cnc Milling On Energy Consumption Of Machining Process, Luqman Dwi Saputra, Eko Yudiyanto
Journal of Mechanical Engineering Science and Technology (JMEST)
The use of CNC milling machines to produce components, especially aluminum brackets used for automotive, is one of the advances in the industrial field. The use of CNC milling machines has the advantage of producing processes with speed accuracy, and better workpiece quality than conventional machines. This research investigates energy consumption in the CNC milling process by varying the toolpath motion strategies—Zigzag, Constant Overlap Spiral, Parallel Spiral, and Parallel Spiral Clean Corners—as well as feed rates of 700 mm/min, 800 mm/min, 900 mm/min, and 1000 mm/min. The goal is to find out the best parameters for using energy in the …
Boiling Heat Transfer Coefficient And Critical Heat Flux On Conical Cylindrical Copper Under Surface Modification, Muhammad Dimyati Nashrullah, Andi Sanata, Imam Solahuddin, Nasrul Ilminnafik, Indro Pranoto, Adhika Widyaparaga
Boiling Heat Transfer Coefficient And Critical Heat Flux On Conical Cylindrical Copper Under Surface Modification, Muhammad Dimyati Nashrullah, Andi Sanata, Imam Solahuddin, Nasrul Ilminnafik, Indro Pranoto, Adhika Widyaparaga
Journal of Mechanical Engineering Science and Technology (JMEST)
This study examined how surface roughness and nanoceramic coating, influences the boiling heat transfer coefficient (BHTC) and critical heat flux (CHF) of a conical cylindrical copper test specimen. Three test specimens exhibiting surface roughness of 0.22 µm, 0.14 µm, and 0.04 µm were analyzed for comparison. Two additional test specimens were treated with nanoceramic coatings utilizing silicon carbide as the base material: one specimen received a single-layer coating and the second was applied with a double-layer coating. The behavior of the bubbles was closely observed with a high-speed camera to deepen the analysis. The experimental results showed that the test …