Computational Engineering Commons^™

New Design Of Aluminum 6061 Welding Joining Using Friction Stir Welding Method, Widia Setiawan, Nugroho Santoso, Surojo Surojo

Journal of Mechanical Engineering Science and Technology (JMEST)

Parallel, lap, corner, and T joints are commonly used in fusion welding and solid welding. Other joints made are lap and butt joint. This study aims to evaluate a new design of fitting model single U and double U for friction stirr welding of Aluminum. Aluminum sheet 6061with a thickness of 10 mm, will be cut to a length of 150 mm and a width of 100 mm, then a locking groove will be made with an inner size of 5 mm and a length of 150 mm The flow is used to be paired in the FSW process. This …

Optimization Of Stir Casting Of Aluminum Matrix Composites (Amcs) With Filler Of Recycled Glass Powder (Rgp) For The Mechanical Properties, Yusup Hendronursito, Tumpal Ojahan, Anang Anshori, Asep Yunanto

Journal of Mechanical Engineering Science and Technology (JMEST)

A study of making Aluminum Matrix Composites (AMCs) uses recycled glass powder (RGP) as a filler has been carried out through the stir casting process. The experimental design uses the Taguchi method of 3^3 orthogonal array L9 with the parameters of powder size (20>x> 80, 80>y> 200, 200>z> 325), percentage of filler vs matrix (2%, 7%, 12%), and stirring time (30 Seconds, 3 Minutes, 12 Minutes). The optimum conditions for the hardness of Al-GRp composites were obtained from specimens with Mesh powder size parameters 200> z> 325, the percentage of glass vs aluminum powder was 12% wt, …

Energy And Exergy Efficiency Of Double Slope Passive Solar Still, Jandri Fan Ht Saragi, Wawan Septiawan Damanik

Journal of Mechanical Engineering Science and Technology (JMEST)

Solar desalination functions to filter water, both sea water and brackish water, to produce clean water that is fit for consumption with energy from the sun. Solar energy is a renewable energy source that has been widely studied for its use. One of its uses is in a double slope passive solar still where the sun is the main source. Energy and exergy obtained from solar energy are not all used to evaporate water in the desalination system, so it is necessary to calculate efficiency energy and exergy in the system. This study aims to obtain data on the amount …

Design Of Savonius Vertical Axis Wind Turbine For Vehicle, Filian Arbiyani, Fernando Pranata Lasut

Journal of Mechanical Engineering Science and Technology (JMEST)

The use of cellular phones is increasing in society, but due to the limited battery capacity of cell phones, it is necessary to charge the battery when travelling in the long distances. The Savonius type wind turbine has a potential as an energy source harvesting the wind energy flowing around the car. However, due to the available space on the car, careful design of Savonius vertical axis wind turbine for vehicle is necessary. The research is conducted numerically using MATLAB software. The wind speed, Reynolds number, and electric power output are numerically simulated to obtain the swept area design. Innovative …

The Effect Of Solution Treatment Temperature And Quenching Media Variation In Heat Treatment Process Cu-Zn-Al Shape Memory Alloys On Shape Memory Effect And Microstructures, Wikan Jatimurti, Monica Gayatri K, Mavindra Ramadhani, Rochman Rochiem

Journal of Mechanical Engineering Science and Technology (JMEST)

Shape memory alloys (SMAs) are metal alloys with a reversible ability to recover their shape at a certain temperature after being deformed. This ability referred to as Shape Memory Effect (SME). The application of SMAs such as Ni-Ti and Cu-Zn-Al alloys usually used on automotive, biomedical, etc. The commonly used SMA is Ni-Ti because of its superior SME properties than Cu-Zn-Al, even though the price is quite higher. The SME of Cu-Zn-Al might be improved by increasing the presence of the martensite phase in its microstructure by heat treatment. The heat treatment process given to Cu-21Zn-5Al alloy is a homogenizing, …

Performance Enhancement Of Shell And Tube Heat Exchanger On Parallel Flow With Single Segmental Baffle, Avita Ayu Permanasari, Poppy Puspitasari, Sukarni Sukarni, Retno Wulandari

Journal of Mechanical Engineering Science and Technology (JMEST)

The shell and tube heat exchanger was a tool to exchange the heat energy between fluids with different temperatures that occurred through direct or indirect contact. The energy exchange in fluids could be occurred with the same phase (liquid to liquid or gas to gas) or two fluids with different phase. To date, the process of heat transfer in the industrial field was crucial in machine work. Therefore, there were studies directed to optimize and develop the function and thermal performance of a heat exchanger by adding Baffles to the side of the shell. Vortex flow that occurs with the …

Physical Behavior Of Thermally Affected Bronze And Brass, Samiul Kaiser, Mohammad Salim Kaiser

Journal of Mechanical Engineering Science and Technology (JMEST)

The physical behavior of thermally affected cast copper, aluminum bronze and brass has been studied by subjecting to heating isochronally for one hour at a range of 600°C. It shows that solid-solution hardening takes place into the Al added bronze and Zn added brass metal. Due to heating Al forms hard and brittle intermetallic of copper aluminates into the bronze metal which responses some age-hardening effects. The electrical conductivity of the metals increases initially through heat treatment due to stress relieving and finally decreases due to formation of intermetallic precipitates. The color of the heated samples are also studied through …

Hardness Evaluation On Ss 316l Joined With Gas Tungsten Arc Welding Under Constant Heat Treatment, Duwi Leksono, Imam Sudjono

Journal of Mechanical Engineering Science and Technology (JMEST)

The purpose of this study is to show the hardness of the GTAW welding results on SS 316L metal with surface heating during the welding process. Observations in this study used SS 316L material with heat temperature regulation on the metal surface of the welding process using heating variations of 100 ℃, 120 ℃ and 140 ℃. The welding process of SS 316L material used a welding joint model uses single V-type welding joint with an angle of 60°, a spacing of 2 mm, a root surface of 1 mm and a thickness of 5 mm. Vickers hardness test was …

The Influence Of The Reference Area Of Aileron On The N2xx Aircraft Using Computational Fluid Dynamics, Siti Nur Rahmah, Gaguk Jatisukamto, Hary Sutjahjono

Journal of Mechanical Engineering Science and Technology (JMEST)

Aileron is a control surface that functions as a regulator of roll motion. The movements of the ailerons are opposite to the left and right sides. Previous studies have shown that graphs of hinge moment coefficient (Chm) values increases with increasing angle of attack. This study is to determine the aerodynamic characteristics of aileron by combining the surface area of the vane into the aileron by varying the aileron’s deflection. The calculation is performed using a numerical method in two dimensions (2D) commercial CFD simulation software. The results of the study concluded that the hinge moment coefficient for modified airfoil …

The Effect Of Heat Treatment To The Erosion Rate Of Brass Composite, Aminnudin Aminnudin, Solichin Solichin

Journal of Mechanical Engineering Science and Technology (JMEST)

Brass composites can be improved their mechanical properties by the heat treatment process. The improvement of the mechanical properties of this technique is expected to increase the resistance of the composite to erosion that occurs in the environment of flow water. Brass composites used are compositeswith fly ash 5, 10, 15, and 20%. The heat treatment process was carried out using electric furnace withoutprotective gas. Composite heat up to 350°C and 400°C for 30 min. and quenching with water. Before and after the erosion test, the weight of the test specimen was weighed with analytical scales. The treatment process affects …

Automatic Delamination Segmentation For Bridge Deck Based On Encoder-Decoder Deep Learning Through Uav-Based Thermography, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Concrete deck delamination often demonstrates strong variations in size, shape, and temperature distribution under the influences of outdoor weather conditions. The strong variations create challenges for pure analytical solutions in infrared image segmentation of delaminated areas. The recently developed supervised deep learning approach demonstrated the potentials in achieving automatic segmentation of RGB images. However, its effectiveness in segmenting thermal images remains under-explored. The main challenge lies in the development of specific models and the generation of a large range of labeled infrared images for training. To address this challenge, a customized deep learning model based on encoder-decoder architecture is proposed …

Multiscale Modeling Of Carbon Fibers/Graphene Nanoplatelets/Epoxy Hybrid Composites For Aerospace Applications, Hashim Al Mahmud

Dissertations, Master's Theses and Master's Reports

Significant research effort has been dedicated for decades to improve the mechanical properties of aerospace polymer-based composite materials. Lightweight epoxy-based composite materials have increasingly replaced the comparatively heavy and expensive metal alloys used in aeronautical and aerospace structural components. In particular, carbon fibers (CF)/graphene nanoplatelets (GNP)/epoxy hybrid composites can be used for this purpose owing to their high specific stiffness and strength. Therefore, this work has been completed to design, predict, and optimize the effective mechanical properties of CF/GNP/epoxy composite materials at different length scales using a multiscale modeling approach. The work-flow of modeling involves a first step of using …

Synthesis And Applications Of Hematite Α-Fe2o3 : A Review, Muhamad Muhajir, Poppy Puspitasari, Jeefferie Abdul Razak

Journal of Mechanical Engineering Science and Technology (JMEST)

This article reviewed the hematite α-Fe2O3. It focuses on its material properties, nanostructures, synthesis techniques, and its numerous applications. Researchers prepared the hematite nanostructure using the synthesis methods such as hydrothermal, and, further, enhanced it by improving the techniques to accommodate the best performance for specific applications and to explore new applications of hematite in humidity sensing.

The Effect Of Chlorophyll Concentration From Papaya Leaves On The Performance Of Dye-Sensitized Solar Cell, Dede Rizali, Heru Suryanto, Sukarni Sukarni

Journal of Mechanical Engineering Science and Technology (JMEST)

Dye-Sensitized Solar Cell (DSSC) is the third generation solar cell that has sandwich structure consisted of organic dye material and other components such as titanium dioxide (TiO2) semiconductor, electrolyte, and substrates (counter electrode and working electrode). The dye in the device was made from green plant chlorophyll such as papaya. This research aimed to find the influence of dye concentration from papaya leaves chlorophyll on the performance of DSCC. The discussion covered the output power (Pout), Fill Factor (FF), and efficiency (ɳ). The method in this research was explorative experimental with independent variables such as direct and indirect sunlight. The …

The Flame Characteristics Of Diesel Fuel Blend With Kepuh (Sterculia Foetida) Biodiesel, Dani Hari Tunggal Prasetiyo, Nasrul Ilminnafik, Salahuddin Junus

Journal of Mechanical Engineering Science and Technology (JMEST)

Kepuh biodiesel fuel (sterculia foetida) is an alternative fuel that can be used to replace fossil fuel. Diesel fuel is performed to determine the laminar burning velocity and high flame by adding biodiesel kepuh volume of 10%, 20%, 30%. The purpose of this study was to study the effect of biodiesel and the effect of bunsen burners on the laminar burning velocity and flame height. Bunsen burner is made of copper and stainless steel. Testing of flame characteristics was carried out by heating the mixture of fuel and air at a temperature of 200°C. The purpose of heating the air …

Critical Solid Fraction Point Analysis: Case Study On Cement Mill Machine Diaphragm, Mochamad Achyarsyah, Poppy Puspitasari

Journal of Mechanical Engineering Science and Technology (JMEST)

During the solidification process, metal liquids turn into solid geometry units including the riser and gating system. The disruption in the liquid flow often causes shrinkage in the object. Critical Solid Fraction Point is a critical point where the continuous liquid supply turned solid and unable to pour to some sections. Simulation software can predict the critical solid fraction time of an object and the liquid supply behavior. The simulation helps the designer in the casting design. The application of low steel alloys in the cement industry, e.g., the Diaphragm, needs development to minimize the shrinkage. This research aimed to …

Failure Analysis On Titen Proto-Xx Car Chassis, Gaguk Jatisukamto, Rika Dwi Hidayatul Qoryah, Santoso Mulyadi

Journal of Mechanical Engineering Science and Technology (JMEST)

The car chassis as a skeleton supports all loads and is the most important component. Car chassis requirements must be rigid, twisting resistant, vibration resistant and resistant to fatigue. This study aims to find the cause of the failure of the Titen Proto-XX car chassis connection. The research methodology was conducted by testing the composition of materials and structural analysis using Ansys Workbench Release 15.0 software. The conclusion of the research is that the skeletal structure material uses Aluminum AA series 1XXX with Al content greater than 99.5%, the welding ability is low, causing a failure in the welded joint. …

Characteristic Analysis Of Horizontal Axis Wind Turbine Using Airfoil Naca 4712, Bili Darnanto Susilo, Gaguk Jatisukamto, Nurkoyim Kustanto

Journal of Mechanical Engineering Science and Technology (JMEST)

Wind energy has been developed and used as a source of electrical energy by converting wind energy into electrical energy using a generator. There are some wind turbine parameters that important for wind turbines design and model, includes the size of the rotor radius, airfoil selection, chord length, and pitch angle. The study aims to characterize the performance of a horizontal axis wind turbine using computational methods. The methods used a design and simulation of NACA 4412 and NACA 4712 airfoil using QBlade software using wind conditions in the region of Pancer, Jember. Results show that the maximum Cl value …

Molecular Dynamics Simulations Of Interaction Of Dna Nucleotides And Lignin Oligomers With Small Molecules And Interfaces, Xinjie Tong

LSU Doctoral Dissertations

Molecular dynamics (MD) simulations of interaction of DNA nucleotides with self-assembled monolayers (SAMs) provide valuable information that is critical to the development of a new DNA sequencing technique. We investigated the interactions and transport characteristics of mononucleotides moving through nanoslits with SAMs-covered surfaces. Our simulations focused on nanoslits in which the walls were composed of three different types of SAMs: methylformyl terminated, methyl terminated, and phenoxy terminated. The results demonstrated that the phenoxy terminated surfaces have the shortest required nanoslits length for nucleotides separation.

Using MD simulations, we also investigated the interaction of mono-lignin and oligo-lignols with lipid bilayers and …

The Effect Of Chemical Pretreatment Process On Mechanical Properties And Porosity Of Bacterial Cellulose Film, Tito Arif Sutrisno, Heru Suryanto, Retno Wulandari, M. Muhajir, Shikh Mohd Shahrul Nizan Shikh Zahari

Journal of Mechanical Engineering Science and Technology (JMEST)

Bacterial cellulose (BC) is a natural polymer which have superior properties, like high porosity, high purity, and high permeability. The study objective is to determine the influence of chemical pretreatment on tensile strength and the porosity of BC. The method was to make BC films from pineapple peel extract through fermentation process for 14 days. The pretreatment was conducted by immersion of BC in BmimCl, H2O2, and NaOH solution with a concentration of 2.5%; 5%; and 7.5 %, heated at 80 °C then dried in the oven, and the samples were then tested by a tensile test using ASTM-D636-V standard, …

Study On The Thermal Distortion, Hardness, And Microstructure Of St 37 Steel Plate Joined Using Fcaw, Maijuansyah Maijuansyah, Yanuar Rohmat Aji Pradana, Gaguk Jatisukamto, Solichin Solichin

Journal of Mechanical Engineering Science and Technology (JMEST)

This study sets out to investigate the distortion angle, microstructure, and hardness of St 37 steel plate weld joint produced by FCAW using the welding current of 80, 110, and 140 A. By using flat position, CO2 and E71T-1 wire were utilized as a shielding gas and electrode filler, respectively. The distortion angle measurement was done on 3 different locations of the welded sample perpendicular to weld direction by using bevel protractor. The micro Vickers tests were then applied gradually at the crosssectional surface with a distance of 0, 5, 10 and 15 mm from weld centerline using the load …

Elastic Linear Analysis Of Connecting Rods For Single Cylinder Four Stroke Petrol Engines Using Finite Element Method, Didin Zakariya Lubis, Andoko Andoko

Journal of Mechanical Engineering Science and Technology (JMEST)

A connecting rod is one of the most critical parts in engine assembly which transfers energy from the piston to the crankshaft. The connecting rod mainly undergoes tensile and compressive loading under engine cyclic process. The forces acting on the connecting rod are forces due to maximum combustion pressure and forces due to the inertia of the connecting rod. This research aimed to analyze the design of the connecting rod of single-cylinder four-stroke engines. This study used CAD software for modeling and structural design. Stresses generated across all the locations of the connecting rod were evaluated using FEA Software. Elastic …

The Characteristic Of Overhang Object To Material Usage On Fdm 3d Printing Technology, Redyarsa Dharma Bintara, Aminnudin Aminnudin, Zumrotul Ida, Ferian Rizki Arbianto, Dani Prasetiyo

Journal of Mechanical Engineering Science and Technology (JMEST)

Fuse Deposition Modeling (FDM) 3D printing is one of additive manufacturing technology which physical 3D model is build up layer by layer. The support structure is almost involved on the process if overhang shape is met on the 3D model. It has main function to prevent the 3D printed model from collapsing. Commonly, the single material source of FDM 3D printer machine is to supply building two structure, structure of main 3D object and support structure. Hence, our goal optimizes the using of support material for reducing the main material usage. Furthermore, the sixteen of variation overhang angle is set …

Comparison Study Of Mechanical Properties Of Al-Si Alloy With And Without Nanoreinforce Iron Oxide (Fe2o3), Cepi Yazirin, Poppy Puspitasari, Muhamad Fatikul Arif

Journal of Mechanical Engineering Science and Technology (JMEST)

Nanoreinforce materials such as ZnO, eggshell, Al2O3, TiO2, and ZrO2 have been shown to improve the mechanical properties of Al-Si alloy. Nanomaterial Fe2O3 has many applications as catalysts reaction in electronic devices, for example, semiconductor materials, paint formulations, lithium rechargeable batteries, and is often applied in industrial fields. It is known that Fe2O3 can be synthesized through the stirring process on machine and method used will involve several steps that relatively take a long time. In this study, Al-Si alloy reinforced by using nanomaterial Fe2O3 which sintered at a temperature of 600C for 3 hours aimed to improve mechanical and …

Preparation Of Chitosan-Polyethylene Oxide-Colocasia Esculenta Flour Nanofibers Using Electrospinning Method, Riesca Ayu Kusuma Wardhani, Lia Asri, Muhamad Nasir, Bambang Sunendar Purwasasmita

Journal of Mechanical Engineering Science and Technology (JMEST)

Nanofibers have been prepared from the mixture of chitosan, polyethylene oxide (PEO) and Colocasia esculenta flour (CE flour) by using the electrospinning method. Two different nanofibers were formulated, containing chitosan-PEO and chitosan-PEO-CE flour. The higher concentration of PEO (3%chitosan-6%PEO) (w/v) resulted in more uniform chitosan-PEO electrospun nanofibers without beads. Chitosan-PEO-CE flour was prepared by addition of colloidal CE flour into the solution containing 3%chitosan-6%PEO with variation of the CE flour concentration of 5, 15 and 25% (w/v). Scanning Electron Microscopy demonstrated that the average diameter of chitosan-PEO nanofibers was 128±41 nm, whereas the diameter of chitosan-PEO-CE flour nanofibers was 159±45 …

Experimental And Numerical Simulation Of Split Hopkinson Pressure Bar Test On Borosilicate Glass, Mayank K. Bagaria

Dissertations, Master's Theses and Master's Reports

This study is an extension to the design of ceramic materials component exposed to bullet impact. Owing to the brittle nature of ceramics upon bullet impact, shattered pieces behave as pellets flying with different velocities and directions, damaging surrounding components. Testing to study the behavior of ceramics under ballistic impact can be cumbersome and expensive. Modeling the set-up through Finite Element Analysis (FEA) makes it economical and easy to optimize. However, appropriately incorporating the material in modeling makes laboratory testing essential. Previous efforts have concentrated on simulating crack pattern developed during 0.22 caliber pellet impact on Borosilicate glass. A major …

Integrated Computational Materials Engineering (Icme) Investigation Of Electrical Conductivity And Thermodynamic Stability For Precipitation Strengthened Al-Zn-Zr And Al-Zn-Ni Ternary Alloys, Oladeji Fadayomi

Dissertations, Master's Theses and Master's Reports

High electrical conductivity Al-Zn-TM (TM=Transition metals) alloys with improved mechanical properties and thermal resistance are developed with an integrated computational material engineering (ICME) strategy. From a series of ab initio density functional theory (DFT) simulations assessing combinations of ternary alloys, Al-Zn-Ni and Al-Zn-Zr are determined as alloys with relatively high electrical conductivity compared to several other ternary Al alloy combinations. The zero-temperature stable structure of precipitates formed in these alloys are determined from computed enthalpy of formation as L1₂, with particular focus of examining the influence of Zn on stabilizing the desired L1₂ precipitate phase.

Scanning transmission …

Elevated Temperature Progressive Damage And Failure Of Duplex Stainless Steel, Darren P. Luke

Civil Engineering ETDs

Ductile failure of metals has been the focus of research efforts within academia and industry for many years since it is tremendously important for understanding the failure of structures under extreme loading conditions. However, limited research has been dedicated to elevated temperature ductile failure, which is critical for evaluating catastrophic events such as industrial, structural or shipping vessel fires. A detailed investigation was conducted on the structural response of Duplex Stainless Steel at elevated temperatures. The temperature dependence of elastic modulus, yield strength, ultimate strength, and ductility was measured up to 1000°C and a continuum damage plasticity model was developed. …

The Analysis Of Permeability And Mechanical Properties Of Sand Moulding Using Mixed Material Clamshell (Placuna Placenta) On Sand Casting, Kritchakhris Nawettanaprasert, Zakaria Bagus Aminanta, Putut Murdanto

Journal of Mechanical Engineering Science and Technology (JMEST)

This study objected to determine mechanical properties of sand moulding by conducting tensile test, compressive and shear test, and also permeability test. This study also had the other objective that was analyse clamshell (Placuna placenta) as mixture material for bentonite as binder in manufacturing sand moulding in order to reduce the usage of bentonite. The method that used in this study was pre-experimental method with One-Shot Case Study model. The best mechanical properties obtained on sample 3 clamshell 11%, permeability results obtained was 190 ml/min, tensile strength results obtained for the dry sand was 0.015 kg/cm2, compressive strength obtained for …

Analysis Of Casting Defect, Tensile Strength, And Hardness Of Al-Si Casting Alloy With Percentage Variation Of Clay Binder Bangkalan, Imam Muhtarom, Sunomo Sunomo

Journal of Mechanical Engineering Science and Technology (JMEST)

Casting is one of method that used in forming the work piece by melting specific metal and pouring into moulding that has been prepared. This study aimed to determine the effect of the use of Bangkalan clay as binder in sand moulding against tensile strength, hardness, and defects in Al-Si casting alloy by using gravity casting method. The method used in this study was experimental method then using descriptive analysis. Descriptive analysis included explanation of the test result of tensile strength, hardness, and the type of surface defect of Al-Si casting. Based on the research result obtained the highest shear …