Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Environmental Engineering
Estimating Battery Size Requirements For Tractor Electrification Of Row-Crop Planting Operations, Cheetown Liew, Andrew Donesky, Mark Freyhof, Ian Tempelmeyer, Santosh Kumar Pitla
Estimating Battery Size Requirements For Tractor Electrification Of Row-Crop Planting Operations, Cheetown Liew, Andrew Donesky, Mark Freyhof, Ian Tempelmeyer, Santosh Kumar Pitla
Department of Biological Systems Engineering: Papers and Publications
Power sources such as batteries, used for both on-road and off-road vehicles, are advancing at a rapid pace. Electric batteries are becoming more power dense, thus allowing them to be used as a power source to replace previous diesel or gasoline-powered systems. Efforts are underway to transition off-road agricultural vehicles from Internal Combustion Engine (ICE) vehicles to electric vehicles (EVs); however, the energy requirements of typical agricultural field operations need to be fully understood before such a transition can occur. Theoretical prediction equations available in the American Society of Agricultural and Biological Engineers (ASABE) standards or the use of engine …
Tractor Power Take-Off Torque Measurement And Data Acquisition System, James Bw Roeber, Santosh Pitla, Roger M. Hoy, Joe D. Luck, Michael F. Kocher
Tractor Power Take-Off Torque Measurement And Data Acquisition System, James Bw Roeber, Santosh Pitla, Roger M. Hoy, Joe D. Luck, Michael F. Kocher
Department of Biological Systems Engineering: Papers and Publications
With the mechanization of agricultural operations, agricultural machinery management has become an extensive research field. Sizing tractors and implements to provide the most efficient power transfer has become an ongoing process with advances in technology. Utilization of the rotational power transferred through gear trains from the tractor engine to the power take-off (PTO) shaft is one of the most efficient methods of power transfer to an implement. This research used commercially available torque sensors that were installed on a tractor PTO shaft for measuring the torque delivered to an implement. The torque sensor was calibrated using the Nebraska Tractor Test …
Development And Validation Of A Tractor Drawbar Force Measurement And Data Acquisition System (Daq), James Roeber, Santosh Pitla, Roger M. Hoy, Joe D. Luck, Michael F. Kocher
Development And Validation Of A Tractor Drawbar Force Measurement And Data Acquisition System (Daq), James Roeber, Santosh Pitla, Roger M. Hoy, Joe D. Luck, Michael F. Kocher
Department of Biological Systems Engineering: Papers and Publications
Matching agricultural tractors to implements towed by the drawbar is one of the important aspects of machinery management for ensuring optimum performance and fuel cost savings. A field deployable tractor draft force measurement and data acquisition system was developed and evaluated as part of this research project. A drawbar instrumented to measure draft force in field operating conditions was developed and statically calibrated. The drawbar was calibrated by applying loads from 4.45 to 134 kN using a hydraulic cylinder connected to a 444.8 kN load cell. Testing was conducted with the drawbar installed on a tractor on a concrete track. …
Tractor Hydraulic Power Data Acquisition System, J. B.W. Roeber, Santosh Pitla, Michael F. Kocher, Joe D. Luck, Roger M. Hoy
Tractor Hydraulic Power Data Acquisition System, J. B.W. Roeber, Santosh Pitla, Michael F. Kocher, Joe D. Luck, Roger M. Hoy
Department of Biological Systems Engineering: Papers and Publications
Tractor hydraulic power is used on a wide range of agricultural implements; however, the availability of operational hydraulic data at points other than full engine throttle position is limited. Operators could utilize this hydraulic data to maximize field efficiency and minimize machinery costs when determining suitable machinery for field operations. A field usable hydraulic test apparatus capable of measuring tractor hydraulic pressure and flow rate data was developed. The goal of this study was to determine if a hydraulic flow and pressure measurement device could be installed on the rear of a tractor to provide implement hydraulic power consumption at …
In-Field Fuel Use And Load States Of Agricultural Field Machinery, Santosh Pitla, Joe D. Luck, Jared Werner, Nannan Lin, Scott A. Shearer
In-Field Fuel Use And Load States Of Agricultural Field Machinery, Santosh Pitla, Joe D. Luck, Jared Werner, Nannan Lin, Scott A. Shearer
Department of Biological Systems Engineering: Papers and Publications
The ability to define in-field tractor load states offers the potential to better specify and characterize fuel consumption rate for various field operations. For the same field operation, the tractor experiences diverse load demands and corresponding fuel use rates as it maneuvers through straight passes, turns, suspended operation for adjustments, repair and maintenance, and biomass or other material transfer operations. It is challenging to determine the actual fuel rate and load states of agricultural machinery using force prediction models, and hence, some form of in-field data acquisition capability is required. Controller Area Networks (CAN) available on the current model tractors …