Petroleum Engineering Commons^™

Modeling Of Gas Production From Shale Reservoirs Considering Multiple Transport Mechanisms, Chaohua Guo, Mingzhen Wei, Hong Liu

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Gas transport in unconventional shale strata is a multi-mechanism-coupling process that is different from the process observed in conventional reservoirs. In micro fractures which are inborn or induced by hydraulic stimulation, viscous flow dominates. And gas surface diffusion and gas desorption should be further considered in organic nano pores. Also, the Klinkenberg effect should be considered when dealing with the gas transport problem. In addition, following two factors can play significant roles under certain circumstances but have not received enough attention in previous models. During pressure depletion, gas viscosity will change with Knudsen number; and pore radius will increase when …

Experimental Study And Numerical Simulation Of Hydraulic Fracturing Tight Sandstone Reservoirs, Chaohua Guo, Jianchun Xu, Mingzhen Wei, Ruizhong Jiang

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Unconventional tight sandstone reservoirs have been developed during recent years and a large number of multi-stages fractured horizontal wells have been drilled to stimulate reservoir performance. However, fluid flow in low permeability porous media no longer obeys Darcy's law and instead conforms to low-velocity non-Darcy flow. Most commercial numerical simulation software for multi-stage fractured horizontal well development may cause inaccuracy in simulating performance of tight sandstone reservoirs. In this paper, the investigation of existing conditions of low velocity non-Darcy flow for oil flow in irreducible water saturation tight sandstone cores was conducted and discussed through lab-experiments. And existence of low …

Investigating The Feasibility Of Nitrogen Injection In Turner Valley, Igor Koracin

Graduate Theses & Non-Theses

The Turner Valley gas and oil field was discovered in 1913 and it was one of the main plays that sparked the growth of the petroleum industry in Canada. The Turner Valley formation is a Mississippian reservoir located at a mean depth of 7,546 feet. It is a heavily faulted field, 25 miles in length with an average width of 2 miles and is located 30 miles south-west of Calgary. It is an asymmetric anticlinal structure cut by the y axis with parallel thrust and normal faults.

Due to its early inception and the lack of resource development regulations, Turner …

Modifying Fracture Conductivity Testing Procedures, Kent Blair

Graduate Theses & Non-Theses

Fracture conductivity testing is a measure of how proppant will perform downhole when injected. The current American Petroleum Institute (API) procedure for conductivity testing produces results that are difficult to replicate. In one case three commercial labs tested the same sample of proppant, the results varied between labs and the highest spread in data had an 80% variation (Anderson, 2013). The goal of this thesis is to investigate cell loading procedures that reduce the variation in laboratory results.

A variety of cell loading techniques were tested including Hoke cylinder injection, guar injection, and cell vibration. Hoke cylinder loading was determined …

Oil Recovery In Low Temperature And Salinity Reservoir Rock Using Anionic And Anionic/Cationic Surfactant Formulations, Alec D. Bokhart, Ryan Mulvenna, Bryan Boudouris, Rituraj Borgohain, Cliff Johnston

The Summer Undergraduate Research Fellowship (SURF) Symposium

As oil reserves are being depleted in the United States, there is an increasing need to recover the trapped oil in the reservoir rock which accounts for up to 60% of the total oil available. This oil may be recovered using chemical enhanced oil recovery (EOR) techniques. In our case study, we investigated viable EOR surfactant/polymer formulations for conditions conducive to high efficiency oil recovery in ultra-low salinity, low temperature, and high hardness reservoirs. Formulations were screened for Winsor Phase I (microemulsions) or Winsor Phase III (bicontinuous emulsions),: both of which are conducive to high efficiency oil recovery. Strong emulsion …

A More Superior Preformed Particle Gel With Potential Application For Conformance Control In Mature Oilfields, Paul Tongwa, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The present work presents a nanocomposite preformed particle gel for conformance control in mature oilfields. This product was observed to have a better performance than conventional hydrogels without nanomaterials. Preformed particle hydrogel was designed by the reaction of monomer, initiator, crosslinker, additives, and calcium montmorillonite nanomaterial, whereas conventional hydrogel is designed from just monomer, initiator, crosslinker and additives. The presence of nanomaterial in hydrogel design affords it tremendous improvement in nanocomposite gel properties and behavior compared to conventional hydrogels without any nanomaterial. Additionally, swelling performance, post-degraded gel viscosity, and long-term thermal resistance of nanocomposite gel increased by several orders of …

The Production Of Biobutanol From Biomass Via A Hybrid Biological/Chemical Process, Thomas Melvin Potts

Graduate Theses and Dissertations

Biobutanol use as a fuel began in the late 19th century. Problems remain in economic viability. A review of the state of the art and need for technical advances is presented.

The technical potential of producing biofuel from a naturally occurring macroalgae was studied. The algae grow in Jamaica Bay, New York City, in contaminated water. The process consisted of mechanical harvesting, drying, grinding, and acid hydrolysis to form an algal sugar solution. Clostridium beijerinckii and C. saccharoperbutylacetonicum were used in an acetone butanol ethanol (ABE) fermentation to make butanol. Fermentation was followed by distillation Butanol concentrations during fermentation reached …

Numerical Modeling Of Fluid Migration In Hydraulically Fractured Formations, Toyin Christie Aseeperi

Graduate Theses and Dissertations

Economic production from low permeability shale gas formations has been made possible by the introduction of horizontal drilling and hydraulic fracturing. To ensure that gas production from these formations is optimized and carried out in an environmentally friendly approach, knowledge about the patterns of gas flow in the shale reservoir formation is required. This work presents the development of a shale gas reservoir model for the characterization of flow behavior in hydraulically fractured shale formations. The study also seeks to develop more computationally efficient approaches towards the modeling of complex fracture geometries. The model evaluates the migration patterns of gas …

Life-Cycle Energy And Ghg Emissions Of Forest Biomass Harvest And Transport For Biofuel Production In Michigan, Fengli Zhang, Dana M. Johnson, Jinjiang Wang

College of Business Publications

High dependence on imported oil has increased U.S. strategic vulnerability and prompted more research in the area of renewable energy production. Ethanol production from renewable woody biomass, which could be a substitute for gasoline, has seen increased interest. This study analysed energy use and greenhouse gas emission impacts on the forest biomass supply chain activities within the State of Michigan. A life-cycle assessment of harvesting and transportation stages was completed utilizing peer-reviewed literature. Results for forest-delivered ethanol were compared with those for petroleum gasoline using data specific to the U.S. The analysis from a woody biomass feedstock supply perspective uncovered …

Investigating A Pilot Area In The Williston Basin Three Forks Formation To Determine The Optimal Inter-Well Spacing And Hydraulic Fracture Length To Maximize Economic Recovery, Adhikeshavan Ravee

Graduate Theses & Non-Theses

The objective of this work is to determine optimal inter-well spacing and hydraulic fracture length of the Three Forks assets in the Williston Basin operated by SM Energy. SM Energy is an independent exploration and production company with operations across North America, mainly in Texas and North Dakota. SM Energy recently switched to infill drilling development in their North Dakota assets and is interested in knowing the economically optimal number of wells that can be drilled per two-section drilling unit.

A simulation approach was taken in this research to address SM Energy’s issue. For research purposes a small pilot area …

Correlating Petrophysical Calculations From Density Logs To Production Trends In The Elm Coulee Field, Montana, Colton Mall

Graduate Theses & Non-Theses

This thesis investigates correlations between estimated upper Bakken total organic carbon (TOC) and production data in the Elm Coulee field, and tests two hypotheses for defining simulation model properties with the results. The purpose of this research is to investigate potential correlations between upper Bakken TOC and production and exploit any correlations to develop better methods for defining simulation model properties. This may reduce time necessary to history match production from an Elm Coulee model and help to explain the production variability. The study area is in Montana townships 24N-57E, 23N-57E, and 24N-55E. Public domain completion and production data for …

Microfracture And Surfactant Impact On Linear Cocurrent Brine Imbibition In Gas-Saturated Shale, Yongpeng Sun, Baojun Bai, Mingzhen Wei

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

During and after hydraulic fracturing, fluid-shale interaction has a prominent impact on liquid retention and thus on gas phase permeability and gas productivity. By providing a low surface tension or wettability alteration, surfactants are widely used to decrease liquid retention after fracturing. To evaluate the liquid intake of a rock sample, an imbibition experiment is commonly used, especially when it is treated by a surfactant. However, conventional imbibition experiments with gas shale could not quantitate the imbibition behaviors as it does with conventional rocks because of the low porosity and extremely low permeability of gas shale. In this paper, a …

Separation Of The Petroleum System, Ali Ibrahim Neamah

The Hilltop Review

This study discusses the overall process of crude oil separation as well as the necessary equipment used in the process. Also discussed and analyzed are potential issues seen in the crude oil extraction process. Reasons why these operation problems may occur are analyzed as well as treatment options for such occurring issues are discussed for employees and students alike. This research is based off of personal involvement at the Nasiriyah Degassing Station located in Dhi Qar, Iraq.

A Study On The Heavy Crude Oil Viscosity Reduction With The Dissolution Of Nitrogen And Carbon Dioxide, Abdurahman Ajumobi

Dissertations and Theses

World's energy challenges would be greatly improved upon if half of the world's heavy oil and extra heavy oil could be made to ow in pipelines. Viscosity reduction of heavy oils is the key to solving this problem. In this study, aside from injecting pure nitrogen and pure carbon dioxide separately into the oil, two different compositions of the mixture of the two gases were also injected. In the first mixture, varied quantities of the two gases were used; 62:5%, 82:2% and 86:4% of the mixture was nitrogen while 37:5%, 17:8% and 13:6% was carbon dioxide at total test pressures …

Coalescence-Induced Jumping Of Droplet: Inertia And Viscosity Effects, Samaneh Farokhirad, Jeffrey F. Morris, Taehun Lee

Publications and Research

The problem of coalescence-induced self-propelled jumping of droplet is studied using three-dimensional numerical simulation. The focus is on the effect of inertia and in particular the effect of air density on the behavior of the merged droplet during jumping. A lattice Boltzmann method is used for two identical, static micro-droplets coalescing on a homogeneous substrate with contact angle ranging from 0◦ to 180◦. The results reveal that the effect of air density is significant on detachment of the merged droplet from the substrate at the later stage of the jumping process; the larger the air density, the larger the jumping …

Effect Of Polymer On Disproportionate Permeability Reduction To Gas And Water For Fractured Shales, Lingbo Liu

Masters Theses

"Large volumes of fracturing fluid are required in shale slickwater fracs, and a considerable amount of polymer friction reducer would remain in microfractures if the polymer has not been broken before gas production. It is of major interest to evaluate the effect of polymer on water/gas flow behavior in the microfractures of shale reservoirs. We fabricated six shale fracture models with different fracture widths and set up a core flooding apparatus to conduct brine/gas-injection experiments before and after polymer treatment. A method by which to calculate the residual resistance factor for gas (F_rr,gas) was defined. The experimental results …

Particle Gel Propagation And Blocking Behavior Through High Permeability Streaks And Fractures, Abdulmohsin Imqam

Doctoral Dissertations

Water channeling, one of the primary reservoir conformance problems, is caused by reservoir heterogeneities that lead to the development of high-permeability streaks and fractures. These streaks and fractures prevent large amounts of oil from being recovered. The ultimate objective of this research was to provide comprehensive insight into designing better particle gel treatments intended for use in large openings, including open fractures, high permeability streaks, and conduits to increase oil recovery and reduce water production.

An intensive laboratory study was conducted to better understand the injection and placement mechanisms of millimeter and micron size preformed particle gels (PPGs) through thief …

Characterization Of Kendex® 0834 (Heavy Resins) & Kendex® 0897 (Light Resins), Victor Correa

Open Access Theses & Dissertations

Characterization of crude oil and some of its refined products has always been a challenge in the refining industry. This is mainly due to the high molecular complexity of crude oil. In this research, Heavy and Light Resins extracted from Penn Grade crude oil were analyzed with a wide variety of techniques, ranging from X-Ray Diffraction, Electron Microscopy, Fourier Transformed Infrared, C-13 Nuclear Magnetic Resonance, and chromatographic methods. An asphaltene extraction protocol was performed on both products. Only the Heavy Resin sample yielded a low amount of asphaltene. Results show that both Resins have a high degree of carbon branching, …

Deepwater Gulf Of Mexico Oil Spill Scenarios Development And Their Associated Risk Assessment, Muhammad Zulqarnain

LSU Doctoral Dissertations

World’s growing energy demand has pushed oil companies to explore and produce hydrocarbons in complex and technologically challenging deepwater environments. These difficult and complex operations involve the risk of major accidents as well, demonstrated by disasters such as the explosion and fire on the UK production platform Piper Alpha and capsizing of the Deepwater Horizon rig in the Gulf of Mexico (GoM). Accidents cause death, suffering, pollution of the environment, disruption of business and bad reputation to oil industry. A quantitative risk analysis technique has been used in this study to identify and categorize risk associated with different life phases …

Measurements And Modeling Of Hydrocarbon Mixture Fluid Properties Under Extreme Temperature And Pressure Conditions, Babatunde A. Bamgbade

Theses and Dissertations

Knowledge of thermodynamic fluid properties, such as density and phase behavior, is important for the design, operation, and safety of several processes including drilling, extraction, transportation, and separation that are required in the petroleum. The knowledge is even more critical at extreme temperature and pressure conditions as the search for more crude oil reserves lead to harsher conditions. Currently, there is dearth of experimental data at these conditions and as such, the predictive capability of the existing modeling tools are unproven. The objective of this research is to develop a fundamental understanding of the impact of molecular architecture on fluid …

Experimental Study Of Crude Oil Emulsion Stability By Surfactants And Nanoparticles, Zainab Alabdulmohsen

Masters Theses

"Surfactants and nanoparticles are materials being widely used for enhanced oil recovery (EOR). Surfactants are mainly used to reduce the interfacial tension between oil and water which could form a stable film of emulsion between these two immiscible fluids. Also, nanotechnology is a potential candidate to offer another solution to improve oil recovery. Nanoparticles can form a solid layer at the droplet's interface and stand as resistant stabilizer under harsh reservoir conditions.

This research investigates whether the combination of surfactants and nanoparticles can provide a more stable emulsion than surfactants only. Two parts of experimental study have been done in …

Evaluation Of Millimeter-Sized Preformed Particle Gel For Conformance Control Treatments Using Simple Models, Ali Abdulmohsen Al Brahim

Masters Theses

Millimeter-sized preformed particle gels (PPGs) have been successfully used to tackle the high-permeable zones, fractures and channels in mature oilfields for conformance control improvement. PPGs can significantly reduce the permeability of abnormal fractures and divert injected water to the low permeable zones where hydrocarbon was not swept by previous water flooding. Due to the irregularity of PPGs in shapes after swollen, their strength cannot be easily measured using the conventional methods. Therefore, the open hole screen plate models with various hole diameters and density were designed to establish a simple technique that can be used to measure the strength of …

Evaluation Of Preformed Particle Gel Treatment Using Homogeneous And Heterogeneous Models, Hilary Ogochukwu Elue

Masters Theses

"This research investigates the effects of preformed particle gel (PPG) in remedying the problems of excess water production and low oil recovery of heterogeneous reservoirs by placing the PPG in the high-permeability layer, thus diverting displacing brine to the unswept low permeability layer. This investigation was completed with three tasks.

The first task was to evaluate the PPG swelling kinetics and strength as a function of concentration of brine. The result of this task indicate that PPG prepared with low concentration of brine swells more, becomes weaker, more deformable than PPG prepared with high concentration of brine.

The second task …

Co₂ Miscible Flooding Application And Screening Criteria, Mingfei Yin

Masters Theses

"Field experience has shown that CO₂ miscible flooding is an effective method to improve oil recovery, but only with proper reservoir candidate selection and optimal project design. This paper discusses both CO₂ miscible and immiscible flooding mechanisms and offers some guidelines for flooding operations. New developments in MMP determination are also introduced.

This research is based on a summary of field data from 134 CO₂ projects in the U.S. Several numerical methods have been applied for data cleaning. After cleaning, data from 128 projects have been analyzed and correlated. Carbonate reservoirs and sandstone reservoirs are the two …

Synthesis Of Different Sizes & Functions Nanoparticles, Jiaming Geng

Masters Theses

"Nanogels, whose size range from 1 to 100nm, have been interested in many research areas: cosmetics, pharmaceuticals, catalysts, photochemistry, and in optical switches or sensors. In Petroleum Engineering area, nanogels can be used as conformance control agent and emulsion stabilizer. And after grafting functional groups or hybrid, nanogels can be used as tracer for the visual modeling.

Though nanoparticles have been studied for more than 20 years, few of them are about nanogels. In the thesis, stirring rate, surfactant type and concentration were found have a large impact on the synthesis of nanogels. And cationic nanogels have salt and acid …

Steam Flooding Screening And Eor Prediction By Using Clustering Algorithm And Data Visualization, Na Zhang

Masters Theses

"Enhanced Oil Recovery (EOR) techniques are vitally important in the oil industry because these techniques could not only extend the life of wells, but also produce 10% to 30% additional oil from the reservoir. However, selecting the most suitable EOR techniques for unknown reservoirs is not easy for decision making. Based on literature, EOR screening criteria could help to find the best candidates for unknown projects, which is classified into two categories: conventional EOR screening and advanced EOR screening. In this research, an artificial intelligent (AI) method, hierarchical clustering algorithm, is adapted to analyze both steam flooding projects and worldwide …

Survey And Data Analysis Of Polymer Flooding Pilot And Field Applications In China, Yandong Zhang

Masters Theses

"Enhanced oil recovery (EOR) processes are regarded as important methods to recovery remaining oil after primary and secondary recovery. It is significant to select the most appropriate EOR process among the possible techniques for a candidate reservoir. EOR screening criteria has been created using available EOR datasets and served as the first step to compare the suitability of each EOR method for a particular reservoir. Most of these datasets are collected from EOR surveys published by Oil & Gas Journal. This study proposes a comprehensive study of a dataset including 55 pilot and field polymer flooding applications in China. Statistical …

Multiscale Modeling Of Particle Transport In Petroleum Reservoirs, Layne Bryan French

LSU Master's Theses

Modeling subsurface particle transport and retention is important for many processes, including sand production, fines migration, and nanoparticle injection. In this study, a pore-scale particle plugging simulator is concurrently coupled with a streamline reservoir simulator to predict the behavior of particles in the subsurface. The coupled simulators march forward in time together. The automated communication between the two models enables the prediction of spatially and time dependent parameters that control the particle transport process. At each time step, the reservoir simulator provides the inlet velocity and particle concentration of the fluid suspension to the pore-scale model which outputs the permeability, …

Modelling Of Channelization In Unconsolidated Formations Due To Liquid Injection, Juan Felipe Bautista Barake

LSU Master's Theses

Fluid injection has been increasingly implemented in oil and gas producing fields to optimize hydrocarbon production in both young and mature oil fields across the globe. This situation arises from the realization that early planning of second and tertiary recovery methods may improve project economics significantly. Injectors are then intended to perform at high injection rates with low bottomhole flowing pressures for as long as possible. In the case of injectors drilled in unconsolidated formations, deficient performance often times seems to be the norm. With a majority of these fields being offshore developments in which capital expenditures are high, a …

Application Of Computational Fluid Dynamics To Near-Wellbore Modeling Of A Gas Well, Oscar Mauricio Molina

LSU Master's Theses

Well completion plays a key role in the economically viable production of hydrocarbons from a reservoir. Therefore, it is of high importance for the production engineer to have as many tools available that aid in the successful design of a proper completion scheme, depending on the type of formation rock, reservoir fluid properties and forecasting of production rates. Because well completion jobs are expensive, most of the completed wells are usually expected to produce as much hydrocarbon and as fast as possible, in order to shorten the time of return of the investment. This research study focused on the evaluation …