Space Vehicles Commons^™

System Integration And Validation Of The Cal Poly Spacecraft Attitude Dynamics Simulator Mk. Iv, Bricen S. Rigby

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project that seeks to enable the simulation and validation of sensors, actuators, and control logic related to spacecraft attitude control. The SADS platform rests atop a spher- ical air-bearing device which allows for nearly frictionless rotation in all three axes. The orientation of the platform is controlled by four reaction wheels arranged in a pyramidal configuration. Over the past few years, there have been significant updates to the reaction wheel subsystem, as well as requests for a more capable central com- puter. Therefore, a new system architecture for the …

Mars Rover Wheels And Drive, Presley S. Sacavitch, Ryan W. Trevena, Dylan A. Mack, Daniel Hudak

Mechanical Engineering

Cal Poly’s Poly1Rover team, advised by Professor Rich Murray, aims to deploy four student-designed mini-Mars rovers, each equipped with a sample-tube retrieval claw, before 2030. However, the wheels of Poly1Rover’s current 6th generation rover are not ready for deployment to Mars, as they do not utilize space-grade materials, are not optimized for manufacturability, and lack sufficient spoke compliance to absorb landing and high-impact loads. This project will be developed by a team of Mechanical Engineering students at California Polytechnic State University, San Luis Obispo (Cal Poly): Daniel Hudak, Dylan Mack, Presley Sacavitch, and Ryan Trevena. Next Intent is providing funding …

Development Of A Free-Floating Space Robotic Simulator, Truman: Terrestrial Robotic Unit For Multibody Analysis And Navigation, Jackson W. Cordova

Master's Theses

This work describes the development of a 3 Degree-of-Freedom (DOF) robotic manipulator for use on a free-floating planar air-bearing vehicle. The system developed aims to serve as a foundation for future space robotics research at the California Polytechnic State University (Cal Poly)’s Space Robotics Laboratory. Systems doc- umentation describes conceptual operation and architecture of the proposed system: Terrestrial Robotic Unit for Multibody Analysis and Navigation (TRUMAN). The key operation of TRUMAN is to study a self launch maneuver of a free-floating ve- hicle including 4 distinct phases: launch off a fixed rail, coast, reorientation using manipulator motion, and capture of …

Spaceotter: A Floating Spacecraft Simulator Air Bearing Vehicle For Hardware-In-The-Loop Experiments And Research, Alexander Debartolo

Master's Theses

Growing interest in nanosatellites has increased demand for accessible ground-testing methods, which have historically been expensive and restricted. Floating Spacecraft Simulators (FSS), built around Air Bearing Vehicles (ABVs), address this gap by approximating a zero-gravity, friction-minimized environment suitable for testing spacecraft control systems, robotics, and propulsion on the ground.

This thesis presents the design, realization, and initial performance characterization of the Space Optically Tracked Testbed for Experiments and Research (SpaceOTTER) ABV, developed for the Cal Poly Space Robotics Lab. SpaceOTTER is the first step toward emulating the 3 degree of freedom (3-DOF) planar dynamics of a simulated spacecraft and is …

Hamster: Hybrid-Actuated Mobile Spherical Terrain Exploration Rover, Winnie Gao

Master's Theses

The expansion of space exploration to increasingly challenging planetary environments requires mobility systems capable of extreme traversal capabilities and operational reliability. This thesis presents the design, development, and testing of a low-cost Hybrid-Actuated Mobile Spherical Terrain Exploration Rover (HAMSTER) intended for use on a planetary surface exploration mission. HAMSTER uses a pendulum-based actuation method for steering and an actuated internal shaft to propel the vehicle forward. The internal structure includes a two-tiered central case composed of the navigation control module, accelerometer, motor controller, primary DC motor, battery, voltage regulators, Raspberry Pi, pendulum servo motor, and drive shafts. Additive manufacturing through …

A Scalable Iteration Of The Horizon Simulation Framework Using Multithreading Techniques, Jason E. Beals

Master's Theses

The Horizon Simulation Framework (HSF) occupies a unique space in the modern aerospace modeling landscape, enabling flexible, modular modeling of mission-level agent behavior through an object-oriented, hierarchical design. HSF's hallmark breadth-first search scheduling algorithm explores a "multiverse" of possible mission execution pathways, enabling exhaustive evaluation of schedule combinations against user-defined heuristics.

As aerospace systems become increasingly complex, HSF faces critical challenges in establishing verifiable, deterministic behavior. The framework's core scheduling algorithm had not undergone systematic validation, leaving questions about temporal consistency, state management correctness, and reproducibility across different program executions. Furthermore, the exponential growth of schedule combinations creates computational bottlenecks …

Surp: Space Robotics Laboratory Lab Manuals And Experiment Development, Connell Crawford

College of Engineering Summer Undergraduate Research Program

This SURP project is focused on the preparation of the lab, experiments, and operation procedures necessary for the proposed equipment in the Space Robotics Lab. As such, the primary goal is to create safety and test documentation that shall be used in the lab. Students selected for this project shall gain a hands-on learn-by-doing with equipment that is intended for teaching and research of a simulated planar space test environment for an air-bearing vehicle test bed to be able to test sensors, actuation and deployment of mechanisms, spacecraft collaboration through closed loop control, as well as experimental propulsion systems.

Investigation Into Silicone-Silicate Conversion Due To Atomic Oxygen In The Low Earth Orbit Environment, Justin T. Self

Master's Theses

Silicones have been widely used over the years in spacecraft for a variety of functions, but atomic oxygen (AO) exposure in Low Earth Orbit causes a silicate (SiO₂) surface layer to rapidly develop on the silicone which results in a permanent change in its thermal and optical properties. Although this silicone to silicate conversion is known to occur, statistical predictions of layer formation as a function of time on orbit are not found in literature. This thesis utilized optical and scanning electron microscopy, Fourier-Transform Infrared Spectroscopy, diffuse reflectance spectroscopy, and nonlinear regression statistical techniques after RF plasma asher …

Preliminary Analysis Of A 12u Astronomy Cubesat, Charles Van Steenwyk

Master's Theses

The explosion of exoplanet astronomy has led to thousands of new discoveries and opportunities to be explored. The ability to capture images and perform meaningful science has resulted in an abundance of follow-on missions, surveys, and fostered a community of amateur astronomers in the last ten years. This success mirrors the development of CubeSats, which have proved an immensely popular way for students of all levels to access space and collect data. Multiple CubeSats have been developed to observe and characterize single exoplanet tran- sits, showing that this class of mission is possible. However, there is currently no mission designed …

The Effect Of Atomic Oxygen On Additively Manufactured Materials, Ryan Grogan

Master's Theses

Additive manufacturing (AM) is a rapidly developing manufacturing method utilized in fields such as the aerospace industry. In-space AM is a technology of interest for the future of spaceflight, including on-orbit manufacturing. However, AM materials are subject to defects that may impact their performance in space-based applications. How these defects change the material’s reaction to the space environment, specifically atomic oxygen (AO), has only recently been explored. AO is a highly corrosive, dominant constituent in low Earth orbit that causes continuous erosion of spacecraft surfaces. The effect of AO on various AM materials is investigated in this thesis. Stainless steel, …

Launch Vibration Attenuation For In-Space Assembly Cargo, Jered Bell

Master's Theses

This thesis investigates the implementation of a passive isolator with a pressurized air cushion for spacecraft payloads in mission architectures implementing in-space assembly technologies. A pressurized air bed capable of briefly surviving the space environment for cargo delivery was prototyped and experimentally evaluated for launch vehicle vibration dynamics resulting in a 72%, 93%, and 88% reduction in experienced GRMS loads for the X-Axis, Y-Axis, and Z-Axis, respectively. A preliminary Total Mass Loss evaluation of the Low-Density Polyethylene Film utilized for the air bed resulted in a mass loss of 0.7%, indicating that commercial off-the-shelf films might require minimal modification for …

Hardware-In-The-Loop Reaction Wheel Testbed With Camera Vision, Abigail Romero, Harvey Perkins, Stephen Kwok-Choon

College of Engineering Summer Undergraduate Research Program

Reaction wheels are widely used in aerospace systems as a method of attitude control. This research was focused on the design, development, and testing of a hardware-in-the-loop reaction wheel testbed that can be used for research and teaching applications related to satellite navigation and control. This project successfully utilized commercial off-the-shelf components to develop a reaction wheel capable of controlling the orientation of a freely rotating platform, as well as tracking objects using computer vision.

Development Of User Interface And Testing Harness, Jacob Amezquita, William Albertini

College of Engineering Summer Undergraduate Research Program

No abstract provided.

Gyroless Nanosatellite Attitude Determination Using An Array Of Spatially Distributed Accelerometers, Kory J. Haydon

Master's Theses

The low size and budget of typical nanosatellite missions limit the available sensors for attitude estimation. Relatively high noise MEMS gyroscopes often must be employed when accurate knowledge of the spacecraft’s angular velocity is necessary for attitude determination and control. This thesis derived and tested in simulation the “Virtual Gyroscope” algorithm, which replaced a standard gyroscope with an array of spatially distributed accelerometers for a 1U CubeSat mission. A MEMS accelerometer model was developed and validated using Root Allan Variance, and the Virtual Gyroscope was tested both in the open loop configuration and as a replacement for a gyroscope in …

Development Of Mirror Flexures For Use In The Muvi Instrument, Colin W. Harrop

Master's Theses

The Miniaturized Ultraviolet Imager (MUVI), is a compact wide field UV imaging instrument in development at UC Berkeley Space Sciences Laboratory and Cal Poly, San Luis Obispo. MUVI is designed to fit in a 2U CubeSat form factor and provide wide field, high resolution images of the ionosphere at far ultraviolet wavelengths. This thesis details the design and analyses of MUVI’s deployable cover mirror mounting flexures. Three different flexure geometries were evaluated, an optimal candidate was determined based on a number of criteria including isolation of vibration and stress to the mirrors, manufacturability and cost. The design of the flexure …

3-Axis Reaction Wheel System For Cubesats, Alexandra Mae Lee, Daniel Leon, Christopher Pablo Casillas, Rose Mccarver

Mechanical Engineering

Reaction wheels are a common, but expensive, component used in CubeSats, that can accurately position a satellite using an imparted momentum (or impulse) from a rotating flywheel to adjust a satellite’s attitude. This document serves as the final design review and report for the 3-Axis Reaction Wheel Senior Design Project in the Mechanical Engineering Department of California Polytechnic State University, San Luis Obispo. The goal of this project is to produce a functional, low-cost 3-axis reaction wheel system based on previous research done by a master’s student at Cal Poly to be implemented in future CubeSats in the Cal Poly …

Investigation On The Use Of Small Aperture Telescopes For Leo Satellite Orbit Determination, Luis R. Curiel Iii

Master's Theses

The following thesis regards the use of small aperture telescopes for space domain awareness efforts. The rapidly populating space domain was motivation for the development of a new operation scheme to conduct space domain awareness feasibility studies using small telescopes. Two 14-inch Schmidt-Cassegrain Telescopes at the California Polytechnic State University and the Air Force Research Lab in Kirtland AFB, NM, in conjunction with a dedicated CCD camera and a commercial DSLR camera, were utilized to conduct optical observations on satellites in Earth orbit.

Satellites were imaged during August 2019, and from January 2020 to March 2020, resulting in the collection …

B-Plane Targeting With The Spacecraft Trajectory Optimization Suite, Jared Graef

Master's Theses

In interplanetary trajectory applications, it is common to design arrival trajectories based on B-plane target values. This targeting scheme, B-plane targeting, allows for specific target orbits to be obtained during mission design. A primary objective of this work was to implement B-plane targeting into the Spacecraft Trajectory Optimization Suite (STOpS). This work was based on the previous versions of STOpS done by Fitzgerald and Sheehan, however STOpS was redeveloped from MATLAB to python. This updated version of STOpS implements 3-dimensional computation, departure and arrival orbital phase modeling with patched conics, B-plane targeting, and a trajectory correction maneuver. The optimization process …

Miniaturized Ultraviolet Imager Phase Iii, Bradley D. Albright, Nicolas A. Armenta, Colin W. Harrop

Mechanical Engineering

This document details the work to date, June 9, 2020, done by the Cal Poly Mechanical Engineering senior project team, Miniaturized Ultraviolet Imager: Phase III (MUVI III), sponsored by the University of California, Berkeley – Space Sciences Laboratory (UCB SSL). MUVI III is the third senior project team of an ongoing design, MUVI: the prototype of a 2U sized CubeSat intended to capture aurora images in the ionosphere. The first team, MUVI I, finished development of the UV imager. The second team, MUVI II, designed the mirror mounting and deployable door mechanisms. The goal of MUVI phase III is to …

Design, Validation, And Verification Of The Cal Poly Educational Cubesat Kit Structure, Nicholas B. Snyder

Master's Theses

In this thesis, the development of a structure for use in an educational CubeSat kit is explored. The potential uses of this kit include augmenting existing curricula with aspects of hands on learning, developing new ways of training students on proper space systems engineering practices, and overall contributing to academic capacity building at Cal Poly and its collaborators. The design improves on existing CubeSat kit structures by increasing accessibility to internal components by implementing a modular backplane system, as well as adding the ability to be environmentally tested. Manufacturing of the structure is completed with both additive (Fused Deposition Modeling …

Tumble Bot, Alena Beyer, Blake Gonzales, Jensen Severance, Liam Chaffey

Mechanical Engineering

Passive locomotion is the ability for an object to move from one place to another by the means of the environment. In nature species such as tumbleweed, fox tails, plankton, and man o’ war jellyfish rely on passive modes of transportation for survival and are able to cross vast distances with little to no expenditure of their own energy. This document seeks to explore the feasibility of building a machine relies on the energy of Mars’ environment to explore the Martian surface.

The “Tensegrity Tumbleweed Locomotion” (nicknamed Tumble Bot) senior project was sponsored by NASA Jet Propulsion Laboratory (JPL). The …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

The Effects Of Atomic Oxygen On Patch Antenna Performance And Lifetime, Max J. Barta

Master's Theses

The space environment is a volatile and challenging place for satellites to survive in. For Low Earth Orbiting (LEO) satellites, atomic oxygen (AO) is a constant corrosive effect that degrades the outer surface of satellites over long durations. Atomic oxygen exists in the atmosphere between 180 and 675 km and has a relatively high energy at 4.5 eV, which allows AO to break molecular bonds in materials on the surfaces of spacecraft. As the number and complexity of CubeSat missions increase, there is an increased risk that AO degradation on commercial off the shelf parts (COTS), such as antenna, could …

Redesign Of Cubesat For Beam Charging, Kuba Preis

Industrial and Manufacturing Engineering

This paper is intended to be a study in the applications of the design freedom granted by additive manufacture in the design of a 1U CubeSat frame. The main loads experienced by a CubeSat are structural (during launch) and thermal (solar radiation). Beam charging is an emerging technology which involves charging a CubeSat using a laser beam. In this paper, a CubeSat frame was redesigned to account for the structural loads induced during launch and the thermal loads induced when beam charging. The thermal, weight, design, and structural requirements for a new CubeSat design were derived. The 1U CubeSat frame …

Ultraviolet Imager Application For A Cube Satellite, Jason Grillo, Troy Hajjar, Brady Hill

Mechanical Engineering

This document serves as the final design review (FDR) report for the 2018 Cal Poly CubeSat Ultraviolet Imager senior project, sponsored by UC Berkeley Space Sciences Laboratories (SSL). SSL wants to monitor the ionosphere above Earth to gain a better understanding of its properties and particle interactions. Far Ultraviolet (FUV) imaging is a good way to obtain high quality images of the ionosphere and the Earth's auroras, and advancement in optic technologies have made cube satellites (CubeSats) an ideal vessel for a FUV imager, as they are relatively low-cost, lightweight, and can be repeatedly deployed. These CubeSat FUV imagers could …

Nanosatellite Launch Data-Logger (Sync), Christopher Martin Gerdom

Master's Theses

CubeSat designers are increasingly looking to incorporate delicate structures and optics into their payloads. These delicate payloads, however, may not survive the required absolute-worst-case launch vibration testing needed for flight certification. To help address this problem, and to better match testing conditions to real-world launch environments, this thesis introduces Sync, a compact 1/4U CubeSat payload designed to collect data on the vibrations and thermal environments CubeSats experience inside a deployer on the way to orbit. This data can be used to better understand the launch environment for different vehicles, and help develop new, more realistic testing guidelines that could enable …

Techedsat 7 And 8-Nasa Missions For Earth Observation, Andrew Pham

STAR Program Research Presentations

Big results can come from small satellites, and Technology Educational Satellite 8 or TES-8 is the latest small satellite in the TechEdSat series from NASA Ames Research Center. TechEdSat is a collaborative program, in which advanced university students have a chance to work directly with researchers on NASA Space Projects. Thanks to the assistance of students from several universities around the country every year, TechEdSat has helped NASA develop Nano-satellite technologies and evaluate new ideas for future spacecraft. TES-8 is the eighth satellite of the continuing TechEdSat series. On December 01, 2018 TES-8 followed a Commercial Resupply Service mission to …

Use Of Manifolds In The Insertion Of Ballistic Cycler Trajectories, Oliver K. Morrison

Master's Theses

Today, Mars is one of the most interesting and important destinations for humankind and copious methods have been proposed to accomplish these future missions. One of the more fascinating methods is the Earth-Mars cycler trajectory which is a trajectory that accomplishes repeat access to Earth and Mars with little to no fuel-burning maneuvers. This would allow fast travel to and from Mars, as well as grant the possibility of multiple missions using the same main vehicle.

Insertion from Earth-orbit onto the cycler trajectory has not been thoroughly ex- plored and the only existing method so far is a Hohmann-esque transfer …

Modification Of A Ground Based Atomic Oxygen Simulation Apparatus To Accommodate Three Dimensional Specimens, Charles Ward

Master's Theses

The space environment presents various challenges when designing systems and selecting materials for applications beyond Earth’s atmosphere. For mission success, these challenges must be considered. One of the detrimental aspects of the space en- vironment is Atomic Oxygen, AO. Only present in harmful quantities in Lower Earth Orbit, LEO, AO causes significant damage to materials by breaking molecular bonds. California Polytechnic State University’s, Cal Poly’s, space environments laboratory features an apparatus capable of simulating this environment. Very thin or short samples were tested to observe the mass loss due to erosion of the sample material. Recent modifications to the system …

Utilizing Permanent On-Board Water Storage For Efficient Deep Space Radiation Shielding, Nathan Ryan Gehrke

Master's Theses

As space technologies continue to develop rapidly, there is a common desire to launch astronauts beyond the ISS to return to the Moon and put human footsteps on Mars. One of the largest hurdles that still needs to be addressed is the protection of astronauts from the radiation environment seen in deep space. The most effective way to defend against radiation is increasing the thickness of the shield, however this is limited by strict mass requirements. In order to increase the thickness of the shield, it is beneficial to make mission critical items double as shielding material.

The human rated …