Aerodynamics and Fluid Mechanics Commons^™

Dynamic Response Of A Hingeless Helicopter Rotor Blade At Hovering And Forward Flights, Pratik Sarker

LSU New Orleans Theses and Dissertations

The helicopter possesses the unrivaled capacity for vertical takeoff and landing which has made the helicopter suitable for numerous tasks such as carrying passengers and equipment, providing air medical services, firefighting, and other military and civil tasks. The nature of the aerodynamic environment surrounding the helicopter gives rise to a significant amount of vibration to its whole body. Among different sources of vibrations, the main rotor blade is the major contributor. The dynamic characteristics of the hingeless rotor consisting of elastic blades are of particular interest because of the strongly coupled equations of motion. The elastic rotor blades are subjected …

Cfd Modeling Of Smoke Movement In An Atrium, Robin Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this paper is to better understand the behavior of smoke movement in an atrium. Thus gives first responders and civilians in and out of building a better understanding

With the advancements of modern technology, computers and softwares make simulation models possible such as fire models to simulate fire and smoke movements. In this paper, a computational fluid dynamic (CFD) software Fire Dynamic Simulator (FDS) is used to conduct a series of atrium tests to investigate the effectiveness of smoke exhaust systems. FDS solves the Navier-Stokes equations appropriate for low speed flows (Ma < 0.3) with an emphasis on smoke, heat transport and CO2 concentrations from fires. The default turbulence model used in FDS simulation is the Large Eddy Simulation (LES), which is the solution of Navier-Stokes equations at low speed.

The compartment tested was 9 …

Rotating Mount For Complex Fluid Flow Research, Kirsten Murphy

Honors Theses

Fluid flow around rotating objects is mathematically complex and there is currently limited experimental data on the subject. To make Western Michigan University capable of this research, a rotating wind tunnel mount was developed. The mount design was integrated into the existing setup at the Applied Aerodynamics Laboratory (AAL) to allow seamless transitions between different research projects. Non-rotating and rotating disk prototypes were created from 3D-printed materials to test the mount’s capabilities. Experimental data gathered from utilizing this rotating mount was analyzed to understand the aerodynamic effects on rotating disks in a fluid stream. From testing the rotating disk prototype …

Investigating The Effect Of An Upstream Spheroid On Tandem Hydrofoils, Joel Tynan Guerra

Master's Theses

This thesis documents a series of three dimensional unsteady Reynolds Averaged Navier-Stokes CFD simulations used to investigate the influence of an upstream prolate spheroid body on tandem pitching hydrofoils. The model is validated by performing separate CFD simulations on the body and pitching hydrofoils and comparing results to existing experimental data. The simulations were run for a range of Strouhal numbers (0.2-0.5) and phase differences (0-π). Results were compared to identical simulations without an upstream body to determine how the body affects thrust generation and the unsteady flow field.

The combined time-averaged thrust increases with Strouhal number, and is highest …

Control Driven Scaling Effects Of Motor And Rotors For Urban Air Mobility Design, Agustin A. Giovagnoli

Doctoral Dissertations and Master's Theses

Through this thesis research the problem of controllability and propulsion associated with scaling-up consumer drones to vehicles that may carry significantly larger payloads, including passenger will be analyzed and tested. Controllability is mainly compromised due to the increasing response time of a larger rpm controlled rotor. This requires a more powerful motor, which translates into heavier and larger devices compromising the thrust-to-weight ratio. Collective pitch control at constant rpm is proposed as a first approach to mitigate the controllability problem, and it is tested in a MATLAB Simulink environment. This solution, linked to a Non-linear Dynamic Inversion controller, is simulated …

A Computational Fluid Dynamics (Cfd) Analysis Of The Aerodynamic Effects Of The Seams On A Two-Dimensional Representation Of A Soccer Ball, Allen R. Rohr

Master's Theses

Most major sports today use a dedicated ball or projectile with specific shape, size, and surface geometry, except for soccer. Over the history of the sport, the surface geometry and design stayed relatively unchanged, sewn together using 32 pentagonal and hexagonal panels. However, recent innovations in panel designs differ substantially from the traditional 32 panel ball. The effects these new designs have on the aerodynamic characteristics of the ball have remained largely unknown, even with the influx of experimental research completed in the past decade. Experimental studies have been broad in scope, analyzing an entire ball in wind tunnels or …

Bi-Stability In The Wakes Of Platooning Ahmed Bodies, Daniel M. Stalters

Master's Theses

Autonomous heavy vehicles will enable the promise of decreased energy consumption through the ability to platoon in closer formation than is currently safe or legal. It is therefore increasingly important to understand the complex and dynamic wake interactions between vehicles operating in close proximity for aerodynamic gains. In recent years, a growing body of research has documented a bi-stable, shifting wake generated behind the Ahmed reference bluff body. At the same time, studies of platooning Ahmed bodies have focused on changes to the body forces and moments at different following distances or lateral offsets, typically based around time-averaged measurements or …

Air Temperatures Tutorial, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

A Numerical And Experimental Evaluation Of The Turbulent Heat Flux In A Heated Jet In Crossflow, Michael R. Borghi Jr.

Doctoral Dissertations and Master's Theses

The injection of fully-developed turbulent heated air from a tube into a cooler turbulent duct flow is examined, as an analogy to film cooled turbine blades. Scale Resolving Simulations (SRS) are used to examine the flow numerically. A Detached Eddy Simulation (DES) methodology is examined but found to be ineffective at correctly capturing the physics of the flow. A Large Eddy Simulation (LES) numerical model is developed and applied in which tube and duct turbulence inflow effects are emulated using a divergence-free synthetic eddy method (SEM). The LES sensitivity to the synthetic inflow turbulence is examined with a series of …

Liquid Jet Penetration And Breakup In A Free Supersonic Gas Jet, Hansen Jones

LSU Master's Theses

In the testing of today’s rocket engines, both on large scale vertical test stands and smaller subscale horizontal component testing stands, it is extremely important to be able to accurately quantify and mitigate the thermal and acoustic loads the engines will generate on test stand infrastructure. Due to the large number of parameters that must be considered for many cases, development of a multi-phase computational code is under way to properly analyze and design water spray cooling systems used at NASA’s Stennis Space Center (SSC) and across other NASA centers. As such, a small-scale experiment has been conducted at Louisiana …

Computational Aerodynamics And Anatomical Characterization Of Laryngotracheal Stenosis In Children, William Poynot

LSU Master's Theses

Laryngotracheal stenosis (LTS) is a health condition in which an obstruction in the upper trachea can cause breathing difficulties and increased incidence of infection, among other symptoms. Occurring most commonly due to intubation in infants, LTS often requires corrective surgery. Currently, clinical methods of assessing the blockage region are simplistic and subjective, and it is challenging to determine the most effective surgical strategy for any given patient. In the present work, a comprehensive methodology is proposed for characterizing the stenosis region both in terms of its anatomical parameters and its corresponding aerodynamic properties. The combination of computational fluid dynamics (CFD) …

Design Of A Heavy Lift Rc Aircraft - Society Of Automotive Engineers (Sae) Aero Design® West Competition Team, Jiyoung Hwang, Phillip Nielsen

Undergraduate Research Symposium - Prescott

The SAE Aero West design competition challenges undergraduate students to design and build an RC aircraft that will fly with the maximum number of passengers and luggage possible. The ERAU SAE team focuses on simulation-based research and project methods such as Computational Fluid Dynamics (CFD), aircraft optimization, and Finite Element Analysis (FEA). Designing and manufacturing a well-designed heavy lift aircraft and competing with other groups will give experience in solving engineering problems. The Aerodynamics team is currently focusing on score optimization, aircraft performance and configuration. The propulsion team is constructing a test rig to test various propellers and motors to …

Thermochemical Non-Equilibrium Models For Weakly Ionized Hypersonic Flows With Application To Slender-Body Wakes, Matthew P. Clarey

Theses and Dissertations

The current resurgence of interest in hypersonic technologies has warranted an inquiry into the commonly employed thermochemical non-equilibrium models within computational fluid dynamic (CFD) simulations. Additionally, research has historically focused on forebody flowfields, while studies of the complex wake structure have remained elusive. Although the forebody is of significance for vehicle analysis, the wake presents many exploitative characteristics. This dissertation aimed to address these two deficits. First, two three-temperature non-equilibrium models were developed, increasing the fidelity of hypersonic solutions above that of the legacy two-temperature model. The models were then investigated via zero-dimensional simulations, to detail the non-equilibrium processes, and …

An Analysis Of Harmonic Airloads Acting On Helicopter Rotor Blades, Iftekhar A. Riyad

LSU New Orleans Theses and Dissertations

Rotary wing aircrafts in any flight conditions suffer from excessive vibration which makes the passengers feel uncomfortable and causes fatigue failure in the structure. The main sources of vibration are the rotor harmonic airloads which originate primarily from the rapid variation of flow around the blade due to the vortex wake. In this thesis, a mathematical model is developed for rotor blades to compute the harmonic airloads at rotor blades for two flight conditions vertical takeoff and landing, and forward flight. The sectional lift, drag, and pitching moment are computed at a radial blade station for both flight conditions. The …

Design Of Selectively Compliant Morphing Wind Turbine Blade Section Using Bistable Laminate For Passive Load Alleviation, Abhishek Chopra, Dr. Andres Arrieta, Janav Udani, Jose Rivas Padilla

The Summer Undergraduate Research Fellowship (SURF) Symposium

The design of passively controlled compliant morphing structures for large scale wind turbine blades has been of interest due to the inherent advantages of lower mass and reduced complexity over their active counterparts. Previous studies have indicated that embedding a locally bi-stable element within the turbine blade section successfully allows for achieving passive load alleviation. The embedded bi-stable member switches from one stable state to another at a critical aerodynamic load. This local structural change results in a global shift in the aeroelastic response of the blade section. Building on these preliminary results, this research investigates a two- dimensional wind …

Flow Measurement Using Electron Beam Flourescence, Richard Brookes, Andrew Strongrich, Anthony G Cofer, Alina Alexeenko

The Summer Undergraduate Research Fellowship (SURF) Symposium

Low density, high-speed flows are of interest to many research areas including, spacecraft thrusters, hypersonic vehicle control, and atmospheric re-entry studies. Measurement of low-density gas flows by traditional methods such as Schlieren Photography or Particle Image Velocimetry is often not possible. In order to yield new information about gas behavior at low densities the technique of electron beam fluorescence is being re-evaluated. By recreating previous electron beam fluorescence setups used to measure density, the experiment operating parameters including beam strength and density ranges are assessed and a foundation can be built for further experimentation. Comparing intensity plots of imaged flows …

Parametric Study Of Aerodynamic Performance Of An Airfoil With Active Circulation Control Using Leading Edge Embedded Cross-Flow Fan, M.A. Qayyum Mazumder

Doctoral Dissertations and Master's Theses

A concept of a cross-flow fan (CFF) embedded near the leading edge of an airfoil to actively control the boundary layer for lift and thrust enhancement has been proposed. The design places a cross-flow fan near the leading edge of an airfoil and flow is drawn in from the pressure side of the airfoil, energized and expelled out to the suction side near the leading edge. This CFF system simulates the active boundary layer control by blowing commercial computational fluid dynamics (CFD) code ANSYS Fluent is employed to perform 2-D calculations based on various parameters of the CFF and compared …

Experiments Of Propeller-Induced Flow Effects On A Low-Reynolds-Number Wing, Gavin K. Ananda, Robert Deters, Michael S. Selig

Publications

Novel findings are discussed in this paper that will be especially beneficial to designers and modelers of small-scale unmanned air vehicles and high-altitude long-endurance vehicles that both operate at low Reynolds numbers (Re = 50,000-300,000). Propeller-induced Oow effects in both tractor and pusher configurations on a recta ngular wing using the Wortmann FX 63-137 airfoil (a common low-Reynolds-number high-lift airfoil) are presented in this paper . Significant performance benefits can be found for a wing in the tractor configuration. Experiments, including trip tests and upper-surface oil Dow visualization, show and verify that the propeller slipstream induces early transition to turbulent …

The Development And Validation Of Sinatra: A Three-Dimensional Direct Simulation Monte Carlo (Dsmc) Code Written In Object-Oriented C++ And Performed On Cartesian Grids, David Matthew Galvez

Master's Theses

The field of Computational Fluid Dynamics (CFD) primarily involves the approximation of the Navier-Stokes equations. However, these equations are only valid when the flow is considered continuous such that molecular interactions are abundant and predictable. The Knudsen number, $Kn$, which is defined as the ratio of the flow's mean free path, $\lambda$, to some characteristic length, $L$, quantifies the continuity of any flow, and when this parameter is large enough, alternative methods must be employed to simulate gases. The Direct Simulation Monte Carlo (DSMC) method is one which simulates rarefied gas flows by directly simulating the particles that compose the …

Characterization Of A Turbulent Boundary Layer In Open Channel Flow Using Particle Image Velocimetry, Mathew James Stanek

Electronic Theses and Dissertations

Turbulent boundary layers are influential in numerous applications (e.g. naval architecture, ocean engineering, sediment transport, etc.), yet considerable knowledge gaps still exist. Boundary layers are regions where transfer of mass, momentum, energy, and heat occur within the interface between a fluid and a solid, or between two fluids. Utilization of optical flow measurement techniques to measure the velocity field with high spatial resolution enables non-intrusive investigation of the complex fluid dynamics of boundary layers. In this study two-dimensional Particle Image Velocimetry was employed to investigate, primarily, the overlap layer of a turbulent boundary layer developed in the recirculating flume facility …

Fuel Flow Reduction Impact Analysis Of Drag Reducing Film Applied To Aircraft Wings, Damon Resnick, Chris Donlan, Nimish Sakalle, Cody Pinkerman

SMU Data Science Review

In this paper, we present an analysis of flight data in order to determine whether the application of the Edge Aerodynamix Conformal Vortex Generator (CVG), applied to the wings of aircraft, reduces fuel flow during cruising conditions of flight. The CVG is a special treatment and film applied to the wings of an aircraft to protect the wings and reduce the non-laminar flow of air around the wings during flight. It is thought that by reducing the non-laminar flow or vortices around and directly behind the wings that an aircraft will move more smoothly through the air and provide a …

Design And Performance Estimation Of A Low-Reynolds Number Unmanned Aircraft System, Sean Lauderdale King

LSU Master's Theses

The purpose of this thesis is to conceptually design a fixed-wing unmanned aircraft systems (UAS) with a higher flight-time and top stable speed than comparable systems. The vehicle adheres to specifications derived from the client, the market, and the Federal Aviation Administration (FAA). To broadly meet these requirements, the vehicle must fly for a minimum of three hours, return to the original flight path quickly if perturbed, and must be hand-launched. The vehicle designed must also have a large potential center of gravity movement to allow for customization of the planform and client customization.

An iterative design process was used …

Electro-Drop Bouncing In Low-Gravity, Erin Stivers Schmidt

Dissertations and Theses

We investigate the dynamics of spontaneous jumps of water drops from electrically charged superhydrophobic dielectric substrates during a sudden step reduction in gravity level. In the brief free-fall environment of a drop tower, with a non-homogeneous external electric field arising due to dielectric surface charges (with surface potentials 0.4-1.8 kV), body forces acting on the jumped drops are primarily supplied by polarization stress and Coulombic attraction instead of gravity. This electric body force leads to a drop bouncing behavior similar to well-known phenomena in 1-g₀, though occurring for much larger drops (~0.5 mL). We show a simple …

A Computational Fluid Dynamics Study On The Aerodynamic Performance Of Ram-Air Parachutes, Angelo A. Fonseca Pazmiño

Doctoral Dissertations and Master's Theses

The modeling of a ram-air parachute presents challenges in the prediction of the inflight geometry, as there is a strong interaction between the flow field and parachute structure. This thesis presents the development of a CAD design and CFD methodology to the simulation of ram-air parachutes in steady-state conditions. Starting from a 2D rib drawing, methods were developed to approximate the 3D geometry and efficiently model the parachute as a rigid and impermeable body. The use of distortions was implemented on a 2D, pseudo-2D, and 3D model to enhance their behavior during a real flight. The SST turbulence model was …

A Computational Analysis Of The Aerodynamics And Aeroacoustics Of Jets With Fluid Injection, Marco Coderoni

Doctoral Dissertations and Master's Theses

A detailed numerical analysis of fluidic injection as a tool to reduce noise emission is presented here. The noise reduction strategy, developed at the Pennsylvania State University, is based on injectors that blow air into the diverging section of the nozzle to emulate the effect of interior corrugation on the jet plume. The advantage is that the injection can be activated during takeoff and turned o_ during other phases of flight so that performance is not affected. Numerical simulations are performed on a military-style nozzle based on the GE F400-series engines, with a design Mach number of 1:65, for over-expanded …

Aerothermodynamic Analysis Of A Mars Sample Return Earth-Entry Vehicle, Daniel A. Boyd

Mechanical & Aerospace Engineering Theses & Dissertations

Because of the severe quarantine constraints that must be imposed on any returned extraterrestrial samples, the Mars sample return Earth-entry vehicle must remain intact through sample recovery. Vehicles returning on a Mars-Earth trajectory will attain velocities exceeding any that have been experienced by prior space exploration missions, with velocities approaching 14 km/s. Velocities as high as these will encounter significant heating during atmospheric re-entry to Earth.

The purpose of this study has been to systematically investigate the aerothermodynamic challenges that will result from a Mars sample return, Earth-entry vehicle design. The goal was to enable efficient estimation of maximum stagnation …

A Protocol-Based Blended Model For Fluid Mechanics Instruction, John Solomon, Eric Hamilton, Vimal Viswanathan, Chitra Nayak, Firas Akasheh

Faculty Publications, Mechanical Engineering

A personalized and media-rich learning framework called “Knowledge and Curriculum Integration Ecosystem” (KACIE) has been developed and implemented in a junior level fluid mechanics course in Fall 2016 and Spring 2017. This model shares characteristics of blended instruction as well as a flipped classroom, with an overall structure that includes the application of established principles emerging from the learning sciences and from cognitive neuroscience. These principles have taken form in the KACIE model as classroom protocols or written instructions to scaffold and guide teaching and learning by faculty and students respectively. In KACIE, the course has been presented as a …

The Design And Implementation Of A Supersonic Indraft Tube Wind Tunnel For The Demonstration Of Supersonic Flows, Daniel Kenneth Johnson

Master's Theses

Historically, the endeavor of scale testing flight vehicles at supersonic Mach numbers, especially for long durations, has required the development of closed-loop wind tunnels, which are extremely expensive both to build and operate due to the high complexity and incredible power required to drive such a system. The intermittent blowdown wind tunnel, indraft tunnel, and shock tunnel have alleviated many of these cost requirements to some degree, whilst facilitating testing at very high Mach numbers and enthalpies; however, these systems require the handling of gases at pressures and temperatures that can be prohibitive for many university settings. The Ludwieg tube …

Microfluidic Biosensor With Functionalized Gold Nano Particles On Interdigitated Electrodes, Bharath Babu Nunna

Dissertations

The integration of the microfluidics to the biosensor has growing demand with favorable conditions such as reduced processing time and low reagent consumption. The immuno biosensing with the microfluidic platform helped to make the electrochemical biosensing assays portable due to which this sensing mechanism can be easily implemented in point of care devices. The implementation of the biosensing in the microchannels significantly reduces the sample requirement form milli liter (mL) to micro liter (uL), and thus leads to low volume sample requirement during the sensing. The primary factors contributing to the microfluidic biosensors performance are probe immobilization, specific binding and …

A Microresonator-Based Laser Doppler Velocity Sensor For Interplanetary Atmospheric Re-Entry, Benjamin Wise

Mechanical Engineering Research Theses and Dissertations

In this thesis, a laser velocity sensor concept based on optical microresonators is presented and the application to spacecraft atmospheric entry is explored. The concept is based on the measurement of Doppler shift of back-scattered laser light. Specifically, the Doppler shift is detected by observing the whispering gallery optical modes (WGM) of a dielectric microresonator excited by the back scattered light from particulates and gas molecules. The microresonator replaces the typical Fabry-Perot interferometer and CCD camera system, thereby significantly reducing the size and weight of the overall detection system. This thesis presents proof-of-concept results for this measurement approach. The Doppler …