Aerodynamics and Fluid Mechanics Commons^™

A Comparison Of The Aerodynamic Centers For Panel Code Compressible Corrections And Openfoam 5 For Mach 0.1 To 0.8, Dustin Weaver

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

It is known that the aerodynamic center changes from quarter chord to half chord from incompressible to compressible flows on airfoils. Compressible corrections are derived and implemented in a vortex panel code. These results will be used to find the aerodynamic centers for the specified Mach range of 0.1 to 0.8 in 0.1 increments within - 6 to 6 degrees angle of attack. OpenFOAM 5 cases will be created with specific meshes and settings. The results calculated from OpenFOAM 5 will be compared to the results obtained from the compressible corrections.

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Flight Dynamics: Flying Qualities Of Handling Factors Are Engineered Into The Aircraft Design, Nihad E. Daidzic

Aviation Department Publications

Flight dynamics is an aerospace engineering discupline that addresses aircraft stability and controllability. It is also mathematically very intensive and is traditionally the most difficult in the pilot training curriculum. Ultimately, it does not matter how good steady-state performance of an aircraft design is if its flying (handling) qualities are deficient. Paradoxically, the first airplane Wright Flyer, was statically and dynamically unstable, had large control authority, and was difficult to fly. We've come a long way since those early days, but stability is still vitally important in aircraft design and flight ops. The focus of this article will be airplane …

Aerodynamic And Performance Analysis Of A Morphing Helicopter Rotor System, Vinay Gopal Krishnan

Doctoral Dissertations and Master's Theses

The purpose of this study was to investigate the effect of rotor morphing, specifically variable rotor speed and variable blade twist, on various parameters such as the distribution of angle of attack, lift, power, thrust and/or other metrics describing the performance of a helicopter rotor. A MATLAB based blade element theory model was developed and executed for different flight conditions. The model was validated against the flight test data of a UH-60. Effects on power, lift to drag ratio and rotor drag from variations in blade twist, rotor speed, rotor radius and blade chord was analyzed. Morphing cases were applied …

Manufacturing And Instrumentation Of An Open End Compressed Air Shock Tube, Josue O. Ruiz

Master's Theses

Shock tubes have been used extensively to study shock wave structures and high speed flow features. The purpose of constructing this open end shock tube was to have the ability to produce shock waves in a laboratory setting but also understand the exit flow coming out which can be applied to future studies that are beyond the scope of this work. This undertaking would require that an open end shock tube be built and instrumented with PCB Integrated Circuit Piezoelectric (ICP) Pressure Sensor Model 113B24 that would then be connected to a PCB Model 482C05 Signal Conditioner with the purpose …

Numerical Characterization Of The Flow Field And Heat Transfer Inside The Receiver Of A Parabolic Trough Solar Collector Carrying Supercritical Co2, Samad Gharehdaghimollahajloo

UNLV Theses, Dissertations, Professional Papers, and Capstones

The aim of this research is to provide a detailed numerical analysis of flow field and heat transfer inside the heat collecting element of a parabolic trough collector. The parabolic trough collector is used as the boiler in a direct Super Critical Carbon Dioxide (S-CO2) Brayton cycle.

A single collector is modeled and analyzed with different inlet conditions. The working fluid is supercritical since its pressure is increased to above critical pressure in the compressor while its temperature reaches 300 °C after passing through the recuperators and before entering the solar field. For the first time, this research considers both …

Implementation And Verification Of A Synthetic Eddy Method (Sem) In The Eagle3d Compressible Flow Solver, Patrick Kopper

Doctoral Dissertations and Master's Theses

The objective of this thesis is to implement and evaluate a Synthetic Eddy Method (SEM) into the Eagle3D compressible flow solver. Both the ability of Eagle3D to resolve unsteady turbulent ow field and capability of the SEM to reproduce given Reynolds stress profiles to start realistic turbulent behavior are verified using common academic cases. Eagle3D is a Computational Fluid Dynamics (CFD) solver using a novel combination of a Bounded Central Differencing (BCD) scheme with Weighted Essentially Non-Oscillatory (WENO) approximation to reduce numerical dissipation. SEM is a modern synthetic turbulence method able to reproduce an arbitrary Reynolds stresses specification on discretionary …

Blended Wing Body Propulsion System Design, Parth Kumar, Adeel Khalid

International Journal of Aviation, Aeronautics, and Aerospace

This research paper focuses on the optimization of the propulsion system of a blended wing body design. Two different aspects of the design, the engine placement and count, and the engine itself, are investigated. The preliminary wing of the BWB is created through aerodynamic analysis, and is kept as a constant over the different propulsion system configurations. The engine parameters are first investigated. Equations are derived to express takeoff distance and climb rate as a function of engine sea level thrust, cruise thrust, and the number of engines. Nearly 150 different engine models, in BWB configurations of 2, 3, 4, …

Wingtip Vortex Alleviation Using A Reverse Delta Type Add-On Device, Afaq Altaf

International Journal of Aviation, Aeronautics, and Aerospace

The result of interactions of a wingtip vortex of a half-span wing and vortices generated by a slender reverse delta type add-on device were studied using Particle Image Velocimetry in a closed-loop low-speed wind tunnel. Characteristics of the vortex interactions produced downstream in planes perpendicular to the free stream direction at a mean chord-based Reynolds number, Re_c = 2.75×10⁵, are explored in this work. The study reveals that the reverse delta type add-on device considerably reduces the tangential velocity, vorticity and circulation magnitude of the resultant vortex by up to 79.6%, 85.6% and 48.7%, respectively. It was …

Design And Validation Of Pressure Based Flow Rate Soft Sensor For Freeze-Drying, Pasita Pibulchinda, Tong Zhu, Vaibhav Kshirsagar, Alina A. Alexeenko

The Summer Undergraduate Research Fellowship (SURF) Symposium

Lyophilization or freeze drying is a process of removing water by sublimation. It is commonly used to extend the shelf life of drugs in the pharmaceutical industry. Because the process is costly and time consuming, precise and efficient pressure, temperature control and drying time estimation are required. It is the goal of freeze-drying to run at maximum capacity while staying within the safe zone by carefully controlling the sublimation rate. Currently, real time estimation of sublimation rate is still challenging. The technique available called Tunable diode laser absorption spectroscopy (TDLAS) is invasive, and requires major modifications. The current study focuses …

Effect Of Boundary-Layer Tripping On Turbulence Generation And Trailing-Edge Noise In Transitional Airfoils, James Benjamin Lewis

Doctoral Dissertations and Master's Theses

The need arises for developing quiet aircraft and silent Unmanned Aerial Vehicles (UAVs) to minimize the environmental effects as well as for stealth missions. We focus here on attempting to directly predict the noise associated with airframe by considering a single isolated airfoil. Developing an ability to directly predict the radiated noise and how it is generated is a first step for passive or active control of the generated noise. We choose herein a NACA0012 airfoil and specific flow condition to test whether we can directly predict the sound in accordance with the corresponding experimental data identified in the Benchmark …

Wind Farm Power Prediction In Complex Terrain, Micah Sandusky

Boise State University Theses and Dissertations

There has been increasing interest in predicting the velocity field within wind farms in complex terrain for resource assessment, turbine siting, and power forecasting. These capabilities are made possible by advancements in computational speed from a new generation of computing hardware and numerical methods. The current thesis research focuses on two technical components to advance the current state in wind power forecasting. The first component is improved prediction of wind flow over complex terrain using the versatile immersed boundary method to represent surface boundary conditions on a fixed Cartesian mesh. The proposed approach embodies the law-of-the-wall for rough surfaces and …

Singularity Formation In The Geometry Of Perturbed Shocks Of General Mach Number, Wouter Mostert, Dale I. Pullin, Ravi Samtaney, Vincent Wheatley

Mechanical and Aerospace Engineering Faculty Research & Creative Works

While planar shock waves are known to be stable to small perturbations in the sense that the perturbation amplitude decays over time, it has also been suggested that plane propagating shocks can develop singularities in some derivative of their geometry (Whitham (1974) Linear and nonlinear waves. Wiley, New York) in a nonlinear, wave reinforcement process. We present a spectral-based analysis of the equations of geometrical shock dynamics that predicts the time to singularity formation in the profile of an initially perturbed planar shock for general shock Mach number. We find that following an initially sinusoidal perturbation, the shock shape remains …

Wing Deflection Analysis Of 3d Printed Wind Tunnel Models, Matthew G. Paul

Master's Theses

This work investigates the feasibility of producing small scale, low aerodynamic loading wind tunnel models, using FDM 3D printing methods, that are both structurally and aerodynamically representative in the wind tunnel. To verify the applicability of this approach, a 2.07% scale model of the NASA CRM was produced, whose wings were manufacturing using a Finite Deposition Modeling 3D printer. Experimental data was compared to numerical simulations to determine percent difference in wake distribution and wingtip deflection for multiple configurations.

Numerical simulation data taken in the form of CFD and FEA was used to validate data taken in the wind tunnel …

Leading Edge Boundary Layer Suction Device For The Cal Poly Rolling Road Wind Tunnel, Daniel C. Glover, Liam M. Madden, Robert J. Cabri

Mechanical Engineering

Over the course of three quarters from Fall of 2016 to Spring of 2017, our team designed and built a boundary layer suction device. The boundary layer suction device has three main functions: a scoop that redirects most of the boundary layer air out of the wind tunnel, fans that suck the remaining boundary layer air through a porous plate and ducting and out of the wind tunnel, and a transition bridge that transitions the remaining air smoothly onto the rolling road. The wind tunnel is owned by Cal Poly and the rolling road is a new addition to it. …

An Investigation Of Avian Wing Tip Vortex Generation Using A Biomimetic Approach, David Stewart Martin

Master's Theses

An experimental study has been conducted to develop a process allowing the creation of biologically accurate aerodynamic test models mimicking the slotted primary feather geometry of the Brown Pelican (Pelecanus occidentalis). Preserved examples of both a full Brown Pelican wing and a single primary feather were 3D scanned and digitally reconstructed using a combination of MATLAB and CAD software. The final model was then 3D printed as a collection of smaller components using a LulzBot TAZ 6 printer and Taulman3D T-Glase PET filament. After using various surface finishing techniques to improve the finish of all 3D printed parts, …

Aerodynamics And Vortex Structures Of A Flapping Airfoil In Forward Flight In Proximity Of Ground, Hang Li

McKelvey School of Engineering Graduate Student Theses & Dissertations

The traditional flapping wing high lift mechanism research mainly focuses on the wing in unbounded flow. However, the real insect flight includes not only the unbounded flow field but also the near-surface flight. Therefore, research on near-surface flight can help reveal the high-lift mechanism of insect flight and should also be beneficial to the research on Micro-Air-Vehicles (MAV). In this thesis, the flow fields of an airfoil in hover and forward flight are simulated in the presence of ground by newly available function of “dynamic meshing” in ANSYS Fluent is employed. The characteristics of aerodynamics, pressure distribution, and vortex structure …

Aerodynamics And Shock Buffet Of A Transonic Airfoil In Ground Effect, Boshun Gao

McKelvey School of Engineering Graduate Student Theses & Dissertations

No abstract provided.

Design And Computational Fluid Dynamics Analysis Of An Idealized Modern Wingsuit, Maria E. Ferguson

McKelvey School of Engineering Graduate Student Theses & Dissertations

The aerodynamics of a modern wingsuit has been the subject of very few detailed scientific studies to date. The prevailing design process remains the dangerous “sew and fly” method, in which designs are tested when they are first flown. This study utilizes Computational Fluid Dynamics (CFD) tools to analyze the flow field and aerodynamics of an idealized wingsuit, which is designed using Computer-Aided Design (CAD) modeling. The 3D CAD software Autodesk Inventor is used to create the wingsuit model, which is designed with a Gottingen 228 airfoil cross-section and a relatively large planform of aspect ratio 1.3. The commercial flow …

Uncertainty Quantification Of Turbulence Model Closure Coefficients On Openfoam And Fluent For Mildly Separated Flows, Ike Witte

McKelvey School of Engineering Graduate Student Theses & Dissertations

In this thesis, detailed uncertainty quantification studies focusing on the closure coefficients of eddy-viscosity turbulence models for several flows using two CFD solvers have been performed. Three eddy viscosity turbulence models considered are: the one-equation Spalart-Allmaras (SA) model, the two-equation Shear Stress Transport (SST) k-ω model, and the one-equation Wray-Agarwal (WA) model. OpenFOAM and ANSYS Fluent are used as flow solvers. Uncertainty quantification analyses are performed for subsonic flow over a flat plate, subsonic flow over a backward-facing step, and transonic flow past an axisymmetric bump. In the case of flat plate, coefficients of pressure, lift, drag, and skin friction …

Numerical Study Of The Aerodynamics Of Dlr-F6 Wing-Body In Unbounded Flow Field And In Ground Effect, Ning Deng

McKelvey School of Engineering Graduate Student Theses & Dissertations

The main focus of this thesis is on the simulation of flow past a three-dimensional wing-body configuration (DLR-F6) in ground effect; a complex 3D wing-body configuration in ground effect has never been analyzed in the aerodynamics literature to date. For the purpose of validation of the simulation approach, computations are performed for the DLR-F6 wing-body in unbounded flow and are compared with the experimental data. The commercial CFD solver ANSYS FLUENT is employed for computations. Compressible Reynolds-Averaged Navier-Stokes (RANS) equations in conjunction with Spalart-Allmaras (SA) and - Shear Stress Transport (SST) turbulence models are solved. The validated code is employed …

Literature Review: Biomimetic And Conventional Aircraft Wing Tips, Naseeb Ahmed Siddiqui, Waqar Asrar, Erwin Sulaeman

International Journal of Aviation, Aeronautics, and Aerospace

This paper is an attempt to summarize the effect of wing tip devices employed by birds, as well as aeronautical engineers in the past to improve the performance characteristics of aircraft. The focus is on reduction of the induced drag or drag due to lift also known as inviscid drag. This paper will provide an insight on both biomimetic and conventional wing tip approaches to reduce the induced drag. Prior analysis and experiments on the aerodynamics of airplane performance due to both these separate studies have been discussed. The needs of the industry and their past inventions have been described …

Application Of Strand-Cartesian Interfaced Solver On Flows Around Various Geometries, Yushi Yanagita

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

This work examines the application of a high-order numerical method to strand-based grids to solve the Navier-Stokes equations. Coined "Flux Correction", this method eliminates error terms in the fluxes of traditional second-order finite volume Galerkin methods. Flux Correction is first examined for applications to the Reynolds-Averaged Navier-Stokes equations to compute turbulent flows on a strictly strand-based domain. Flow over three geometries are examined to demonstrate the method’s capabilities: a three-dimensional bump, an infinite wing, and a hemisphere-cylinder configuration. Comparison to results obtained from established codes show that the turbulent Flux Correction scheme accurately predicts flow properties such as pressure, velocity …

Comparison Of Rans Modeling To Dual-Plane Piv Measurements Of The Turbulent Tip Vortex Trailed From A Hovering Rotor, Zachary Lietzau

Doctoral Dissertations and Master's Theses

Numerical simulations using the Reynolds-Averaged Navier-Stokes (RANS) equations were conducted to study the development and turbulent decay of the tip vortices in the wake produced by a hovering rotor. The computational results were compared to detailed, dual plane Particle Image Velocimetry (PIV) measurements of a turbulent tip vortex trailed from a single-bladed rotor. The work investigated both the required mesh resolution and most suitable turbulence closure models with rotational/curvature corrections by assessing their predictions of the tip vortex properties and the overall physical nature of the rotor wake. It was found that even when using a higher-order accurate central differencing …

Extended Surface Heat Transfer Coefficients Via Endwall Temperature Measurements, Yogesh Pai

Doctoral Dissertations and Master's Theses

Short pins are used for internal cooling of the trailing edge in a gas turbine blade. A novel method is described in this thesis which helps in simplifying the experimental process used to obtain average heat transfer data on the pin surface, at the expense of additional post processing complexity. The method is based on a unique, analytical solution of the longitudinal conduction equation with internal heat generation, allowing computation of heat transfer rates via pin base temperature measurements via Temperature Sensitive Paint, or similar non-intrusive methods. Verification of this method is done with comparisons to the solution of infinite …

A Performance And Visualization Study On Inlet Geometries Of A Cross-Flow Fan., Yoel Tanquero

Electronic Theses and Dissertations

A study was conducted to characterize the flow-field in the suction region of different inlet geometries of a cross-flow fan. The characterization was accomplished by correlating the static performance curves measured for each fan-inlet configuration to the streamline plot obtained using a particle tracking velocimetry (PTV) measurement system at three constant flow rates (25, 40, and 55 CFM). The PTV measurement system used was developed by the author and uses helium bubbles as tracers, an LED light sheet, a slow motion camera, and a Matlab program. Four inlet geometry design variables were defined and independently studied to evaluate the effect …

Actuator Disk Theory For Compressible Flow, Htet Htet Nwe Oo

Master's Theses

Because compressibility effects arise in real applications of propellers and turbines, the Actuator Disk Theory or Froude’s Momentum Theory was established for compressible, subsonic flow using the three laws of conservation and isentropic thermodynamics. The compressible Actuator Disk Theory was established for the unducted (bare) and ducted cases in which the disk was treated as the only assembly within the flow stream in the bare case and enclosed by a duct having a constant cross-sectional area equal to the disk area in the ducted case. The primary motivation of the current thesis was to predict the ideal performance of a …

Investigation Of Dynamic Store Separation Out Of A Weapons Bay Cavity Utilizing A Low Speed Wind Tunnel, Andrew D. Bower

Theses and Dissertations

Characterizing mission store trajectories as they separate from a weapons bay cavity is highly relevant to the Air Force mission. The flow around a weapons bay is unsteady. The unsteady flow can cause a mission store separation trajectory to be unpredictable, and such is the case for what some have termed a pitch bifurcation. Traditional wind tunnel testing is incapable of detecting a bifurcation because traditional wind tunnel testing records time-averaged data. In this study, an experimental testing system was developed and refined in order to support the time-accurate characterization of dynamic mission store separation events. A Motion Test Apparatus …

Time-Dependent Validation Of Finite Element Strain Distribution Of A Plastically-Deformed Plate Via Digital Image Correlation, Kevin R. Knapp

Theses and Dissertations

Generation of residual stress is an essential step in the generation of Goodman data via Air Force Research Laboratory's vibration-based fatigue test. Conventional Goodman data is constructed through uniaxial fatigue testing at a rate of 40 Hz, while the vibration-based testing excites stresses at 1,600 Hz in a stress state that is similar to those seen in gas turbine engine airfoils. A pre-strain procedure is conducted to form residual tensile stress, which serves as a steady stress when the specimen is subjected to fully-reversed vibration-based fatigue loads. This steady tensile stress is desired at the fatigue zone of the test …

In-House Fabrication Of Temperature Sensitive Paint For Turbine Cooling Research, Mayur D. Patel, Mark A. Ricklick

Beyond: Undergraduate Research Journal

The Temperature Sensitive Paint (TSP) is a widely used method in measuring and visualizing flow separation and heat transfer. Compared to the cost and time consumption needed for methods such as pitot tubes, temperature sensitive paint is a cheaper alternative. Due to high usage in College of Engineering research projects, it was determined that in house fabrication of temperature sensitive paint would reduce time and cost limitations. For initial stages, literature research was performed to determine the recipe of intensity based TSP with luminophore and polymer binder that operated optimum at temperatures from 0-100°C. Europium III thenoyltrifluoroacetonate was determined to …