Aerodynamics and Fluid Mechanics Commons^™

Experimental Investigation Of Mist Film Cooling And Feasibility Study Of Mist Transport In Gas Turbines, Reda M. Ragab

LSU New Orleans Theses and Dissertations

In the modern advanced gas turbines, the turbine inlet temperature may exceed 1500°C as a requirement to increase power output and thermal efficiency. Therefore, it is imperative that the blades and vanes are cooled so they can withstand these extreme temperatures. Film cooling is a cooling technique widely used in high-performance gas turbines. However, the film cooling effectiveness has almost reached plateau, resulting in a bottleneck for continuous improvement of gas turbines' efficiency.

In this study, an innovative cooling scheme, mist film cooling is investigated through experiments. A small amount of tiny water droplets with an average diameter about 10-15 …

A Wedge Impact Theory Used To Predict Bow Slamming Forces, Ashok Benjamin Basil Attumaly

LSU New Orleans Theses and Dissertations

The pressures and impact forces acting on a hull while experiencing bow wave slamming is analyzed using Vorus' Impact Theory. The theory extends the hydrodynamic analysis of planing hulls from simple wedges to irregular shapes using a Boundary Element Method. A Fortran-based code developed by the Author is used to analyze hullforms. Linear strip theory is used to extend the analysis over a three dimensional hull. Post-processing of output data gives hull pressure distributions at different time steps and is visually presentable.

Impact pressure, Impact force, Planing, Wave slamming, Bow impact, Vorus' theory, Boundary Element Method, Linear strip theory

Experimental Study On The Effect Of Air Flow On Soap Bubble Formation, John M. Davidson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Soap bubbles are a common interfacial fluid dynamics phenomenon having applications such as buoyant hollow spherical fillers and flow visualization of large scale airflows. In contrast to the dynamics of liquid drops in gas and gas bubbles in liquid, the dynamics of soap bubbles has not been well documented, possibly because soap bubbles have gas-liquid-gas interfaces. Having the thin-liquid-film interface seems to alter the characteristics of the bubble/drop creation process. Thus, the main objective of this study is to experimentally examine how airflow develops and interacts with the soap liquid film as the film stretches and finally collapses to pinch-off. …

Adaptive Control Techniques For Transition-To-Hover Flight Of Fixed-Wing Uavs, Brian Decimo Marchini

Master's Theses

Fixed-wing unmanned aerial vehicles (UAVs) with the ability to hover combine the speed and endurance of traditional fixed-wing fight with the stable hovering and vertical takeoff and landing (VTOL) capabilities of helicopters and quadrotors. This combination of abilities can provide strategic advantages for UAV operators, especially when operating in urban environments where the airspace may be crowded with obstacles. Traditionally, fixed-wing UAVs with hovering capabilities had to be custom designed for specific payloads and missions, often requiring custom autopilots and unconventional airframe configurations. With recent government spending cuts, UAV operators like the military and law enforcement agencies have been urging …

Computational And Experimental Comparison Of A Powered Lift, Upper Surface Blowing Configuration, Jay M. Marcos

Master's Theses

In the past, 2D CFD analysis of Circulation Control technology have shown poor comparison with experimental results. In Circulation Control experiments, typical results show a relationship between lift coefficient, CL, vs blowing momentum coefficient, Cμ. CFD analysis tend to over-predict values of CL due to gridding issues and/or turbulence model selection. This thesis attempted to address both issues by performing Richardson’s Extrpolation method to determine an acceptable mesh size and by using FLUENT’s 2-equation turbulence models. The experimental results and CAD geometry were obtained from Georgia Tech Research Institute for comparison with the CFD analysis.

The study showed that 3D …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

High-Order Shock Capturing For Computational Aeroacoustics, Samuel Otto, Gregory Blaisdell

The Summer Undergraduate Research Fellowship (SURF) Symposium

Jet noise is not only an annoyance to passengers and communities near airports, it is a major contributor to hearing loss in veterans who served on aircraft carriers, as well as a significant limiting factor for the growth of commercial airlines. High-fidelity large eddy simulation (LES) is an important tool for analyzing and predicting jet noise; however the utilized non-dissipative high order finite difference schemes produce instabilities at shock waves. Schemes for capturing shock waves, however, are more dissipative and do a poor job preserving turbulent structures and acoustic waves. To maximize the strengths of both approaches, hybrid methods utilize …

Investigation Of Grid Adaptation To Reduce Computational Efforts For A 2-D Hydrogen-Fueled Dual-Mode Scramjet, Kam Keong Foo

Doctoral Dissertations and Master's Theses

A two-dimensional dual-mode scramjet flowpath is developed and evaluated using the ANSYS Fluent density-based flow solver with various computational grids. Results are obtained for fuel-off, fuel-on non-reacting, and fuel-on reacting cases at different equivalence ratios. A one-step global chemical kinetics hydrogen-air model is used in conjunction with the eddy-dissipation model. Coarse, medium and fine computational grids are used to evaluate grid sensitivity and to investigate a lack of grid independence. Different grid adaptation strategies are performed on the coarse grid in an attempt to emulate the solutions obtained from the finer grids. The goal of this study is to investigate …

Qualitative Methods Used To Develop And Characterize The Circulation Control System On Cal Poly's Amelia, Eric N. Paciano

Master's Theses

The circulation control system onboard Cal Poly's Advanced Model for Extreme Lift and Improved Aeroacoustics was a critical component of a highly complex wind tunnel model produced in order to fulfill the requirements of a NASA Research Announcement awarded to David Marshall of the Aerospace Engineering Department. The model was based on a next generation, 150 passenger, regional, cruise efficient, short take-off and landing concept aircraft that achieved high lift through circulation control wings and over-the-wing mounted engines. The wind tunnel model was 10-ft in span, used turbine propulsion simulators, and had a functioning circulation control system driven from tunnel …

Experimental Investigation Of Blowing Effects On Turbulent Flow Over A Rough Surface, Mark A. Miller, Alexandre Martin, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

A high Reynolds number turbulent channel flow facility was used to study the combined effects of roughness and flow injection on the mean flow and turbulence characteristics. It was found that the additional momentum injection through the surface enhanced the roughness effects and for the mean flow the effect of blowing was indistinguishable from that of increased roughness. However, for the turbulence statistics, this analogy broke down in that the addition of blowing resulted in behavior which did not follow that predicted by Townsend’s hypothesis. This was observed as a reduction of outer-scaled Reynolds stress well into the outer layer. …

Fluid-Structure Interaction And Multidisciplinary Design Analysis Optimization Of Composite Wind Turbine Blade, Naishadh G. Vasjaliya

Doctoral Dissertations and Master's Theses

A multidisciplinary design analysis optimization (MDAO) process is defined for a composite wind turbine blade to optimize its aerodynamic and structural performance by developing a fluid-structural interaction (FSI) system. The objectives are to maximize aerodynamic efficiency and structural robustness while reducing blade mass and total cost. In the previous research, a MDO process of a composite wind turbine blade has been pioneered as an effective process to develop structurally optimized blade design. Present MDAO process is defined in conjunction with structural and aerodynamic performance of the blade which is divided into three steps and the design variables considered are related …

Use Of A Rolling Road System In Crosswind Conditions, Mau-Kuo Chen

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel testing continues to play an important role in vehicle aerodynamic development. Accurate results are strongly associated with whether the wind tunnel can closely simulate the on-road conditions, including the Reynolds number and all boundary conditions. Rolling road systems (or moving belts) have been a successful tool for many auto makers and racing teams to simulate the relative motion between the stationary vehicle model and the floor in the test section. The mechanism of the rolling road system is simple, but how it affects the adjacent flow field and how this flow interacts with the flow underneath the vehicle …

Design Advantages Of Skin Friction Drag Reduction Using Riblets, John Michael Gregory

Mechanical & Aerospace Engineering Theses & Dissertations

The research reported here has examined the potential improvements in overall aircraft performance that can result from integrating skin friction reduction technology, such as riblets, early in the aircraft design cycle. This study has shown that riblets can improve the payload capacity, increase the range, and improve performance of transport aircraft. If recent advances in fabrication techniques make it possible to create aluminum wing surfaces with integral riblet geometries, the applications could be widespread and the gains significant.

Microphone-Based Pressure Diagnostics For Boundary Layer Transition, Spencer Everett Lillywhite

Master's Theses

An experimental investigation of the use low-cost microphones for unsteady total pressure measurement to detect transition from laminar to turbulent boundary layer flow has been conducted. Two small electret condenser microphones, the Knowles FG-23629 and the FG-23742, were used to measure the pressure fluctuations and considered for possible integration with an autonomous boundary layer measurement system. Procedures to determine the microphones’ maximum sound pressure levels and frequency response using an acoustic source provided by a speaker and a reference microphone. These studies showed that both microphones possess a very flat frequency response and that the max SPL of the FG-23629 …

Active-Twist Rotor Blades Design, Analysis, And Testing, Andrew Randall Kreshock

Mechanical & Aerospace Engineering Theses & Dissertations

The subject of this thesis is the design, analysis, and experimental assessment of active-twist rotors. These active rotors use piezoelectric actuators embedded in the skins to twist the blade to reduce vibratory loads in the fixed system. First, the design and optimization of the twist response within the geometric and structural constraints of a rotor blade is presented. A parametric analysis is conducted varying the airfoil thickness, active-material placement, and structural plies to determine the maximum static twist response. A Macro-Fiber Composite (MFC), which is a fibrous piezoelectric device is used as the active material. Analyses of the cross-section are …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Design And Fabrication Of A Ramjet Engine, Clinton C. Humphrey

Aerospace Engineering

In this report, the design and fabrication of the inlet to a ramjet engine is described. The inlet utilizes a single ramp and single sided three shock internal compression to slow the airflow from supersonic to subsonic speeds while providing maximum stagnation pressure to the combustor. The optimum angle for the inlet ramp is calculated to be 10° and it decelerates the airflow from Mach 3.3019 to Mach 0.5438. The stagnation pressure increases from 150 psi to 4.67 ksi. The material of the inlet is composed primarily of low carbon mild steel to accommodate the high pressure of the inlet.

Coupled Flow Field Simulations Of Charring Ablators With Nonequilibrium Surface Chemistry, Hicham Alkandry, Iain D. Boyd, Alexandre Martin

Mechanical Engineering Faculty Publications

This paper describes the coupling of a Navier-Stokes solver to a material response code to simulate nonequilibrium gas-surface interactions. The Navier-Stokes solver used in this study is LeMANS, which is a three-dimensional computational fluid dynamics code that can simulate hypersonic reacting flows including thermo-chemical nonequilibrium effects. The material response code employed in this study is MOPAR, which uses the one-dimensional control volume nite-element method to model heat conduction and pyrolysis gas behavior. This coupling is demonstrated using a test case based on the Stardust sample return capsule. Coupled simulations are performed at three different trajectory conditions. The effects of the …

Volume Averaged Modeling Of The Oxidation Of Porous Carbon Fiber Material, Alexandre Martin

Mechanical Engineering Faculty Publications

Charring ablators remain the premium choice for space exploration missions that involve atmospheric re-entry. This type of ablative material is composed of a carbon matrix, usually made of fibers, which is then impregnated with a resin. During re-entry, the high heat flux produced by convective heating causes the material to chemically react. First, the resin pyrolyzes, and is vaporized into a gas that travels through the material, and is eventually ejected at the surface. Then, as the temperature rises, the surface of the porous matrix recess through ablative processes. For re-entry conditions typical of space exploration missions, this is mainly …

Flow-Tube Oxidation Experiments On The Carbon Preform Of Pica, Francesco Panerai, Alexandre Martin, Nagi N. Mansour, Steven A. Sepka, Jean Lachaud

Mechanical Engineering Faculty Publications

Oxidation experiments on the carbon preform of a phenolic-impregnated carbon ablator were performed in the NASA Ames ow-tube reactor facility, at temperatures between 700 and 1300 K, under dry air gas at pressures between 103 and 104 Pa. Mass loss, volumetric recession and density changes were measured at different test conditions. An analysis of the diffusion/reaction competition within the porous material, based on the Thiele number, allowed us to identify low temperature and low pressure conditions to be dominated by in-depth volume oxidation. Experiments above 1000 K were found at transition conditions, where diffusion and reaction occur at similar scales. …

Multi-Dimensional Modeling Pyrolysis Gas Flow Inside Charring Ablators, Haoyue Weng, Alexandre Martin

Mechanical Engineering Faculty Publications

Using an ablative thermal/material response code, the importance of three-dimensionality for modeling ablative test-article is addressed. In particular, the simulation of the pyrolysis gas flow inside a porous material is presented, using two different geometries. The effects of allowing the gas to flow out of the side wall are especially highlighted. Results show that the flow inside the test-article is complex, and that the 0D or 1D assumption made in most Material Response (MR) codes might not be valid for certain geometries.

Incorporating Aluminum Honeycomb To Increase Efficiency Of U-Tube Removable Heat Exchanger, Daniel Soto, Daniel Corona

Aerospace Engineering

This report contains the results of attempting to improve on the results of Scott R. Sawyer and Alan M. L’Esperance research paper “Investigation of Paraffin Wax as an Energy Storage Medium Within a Shell-and-Tube Heat Exchanger.” The overall goal of the paper mentioned was to investigate the usefulness of wax as an energy storage medium. Scott R. Sawyer and Alan M. L’Esperance determined that “the amount of energy that can be released by the paraffin wax back to the airflow reaches a plateau, despite an increase in heating times.” They suggested that by surrounding the airflow tubes of a heat …

Global Skin Friction Diagnostics: The Glof Technique And Measurements Of Complex Separated Flows, Sudesh A. Woodiga

Dissertations

This work describes the application of the global luminescent oil film skin friction meter to quantitative global skin friction diagnostics of complex separated flows. The development of this technique is based on the relationship between the oil film thickness and luminescent intensity of a luminescent oil film. The projected thin oil film equation is given to relate the normalized luminescent intensity with skin friction. The variational formulation with a smoothness constraint on skin friction is proposed to obtain a snap shot solution from two consecutive images for a relative skin friction field. A complete skin friction field is reconstructed through …

Supersonic Turbine Cascade Studies Using Computational Fluid Dynamics And Water Table Experiments, Shelby E. Nelson

Honors College Theses

Design engineers use a variety of tools to perform calculations and to aid in the design process. For example, engineers designing gas turbines, specifically the aerodynamicists, use a combination of hand calculations, experimental data, and complex numerical codes to simulate air flow around each blade. Aerodynamicists designing gas turbines must predict the locations of the shocks to locate inefficiencies in the flow. In this thesis, three methods of calculating the shock angles are compared: analytical, experimental, and computational. Three different airfoil shapes are tested: a rectangular flat plate, a supersonic diamond, and a turbine airfoil. Cascade tests of the airfoil …

Design Considerations And Requirements For In-Flight Refueling Of Unmanned Vehicles, Ian R. Mcandrew, Kenneth Witcher

Publications

The need to refuel in-flight has become a significant part of military strategy for air forces to work at further distances from safe shores. The use of Unmanned Vehicles is increasing and expected to be the principal part of military deployment. This paper will address the concepts and requirements for applying refueling unmanned vehicles in a military context for supporting fixed and rotor aircraft. Design aspects of human factors in the process are considered, reviewed and solutions proposed to allow for the first generation of designs to be developed. Furthermore, the practical and operational limitations will be addressed as part …

Broncoblade: An Open Source Wind Turbine Blade Analysis Tool, Alex R. Quinlan

Masters Theses

This thesis reports the development and validation of BroncoBlade, a horizontal axis wind turbine analysis tool. BroncoBlade prepares finite element models and integrates them with an aeroelastic simulator. Analysis results for the SNL100-00 baseline blade are evaluated against reference results published by Sandia National Laboratories. Variations on the SNL100-00 blade incorporating carbon fiber are compared to the baseline blade.

Characterization Of A Spiral Microfluidic Focusing Device For Continuous Single Cell Impedance-Based Cytometry Applications, Daniel Riley

Mechanical & Aerospace Engineering Theses & Dissertations

A major focus in the field of cell characterization is the quantification of cell dielectric properties in order to develop low-cost, portable microfluidic devices that can, among other things, perform point-of-care detection of rare diseases and complete blood counts. Impedance-based cytometry has become an advantageous tool to ascertain these properties, wherein it is important that cells pass through the same point in a channel cross-section one at a time to ensure accurate and repeatable readings. This study documents the assessment of an 8-loop 160 μm (W) x 80 μm (H) spiral microchannel used to focus 10 μm polystyrene particles. In …

Nonlinearity Index Analysis Of Periodic-Chaotic Stall-Spin Aircraft Motion, Daniel Paul Tapolcai

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis explores the application of nonlinearity index theory to the nature of stalling and spinning aircraft motions. Nonlinear dynamic phenomena related to stall and spin have been a concern to flight engineers and pilots for generations. Considerable past work has been directed to detect and understand the cause and nature of these phenomena. Methods such as bifurcation analysis, Volterra expansion series, and nonlinear simulation are a few of the nonlinear approaches developed to study this topic. Traditionally, however, linear analysis is the most widely used approach for studying aircraft dynamical behavior under a given set of acceptable conditions. This …

Development Of Cfd Models For The Purposes Of Exploring Free Surface Wave Phenomena, Leonard P. Stoehr

Masters Theses

With the push for finding alternative, green energy sources, the harnessing of energy from ocean and lake waves is becoming a more researched field. To fully understand the behavior of wave interactions and optimize designs to extract this energy, it is necessary to develop computer models that can accurately replicate this behavior. A case is presented in which previous work done using the wave tank found in the Western Michigan University fluids lab is examined. The case involves harnessing the energy generated by ocean waves through the usage of plates of different shapes resting horizontally on the water’s surface. The …

Investigation Of Pulse Detonation Engines; Theory, Design And Analysis, Jeff Vizcaino

Doctoral Dissertations and Master's Theses

Detonation and constant volume combustion has been known to the scientific community for some time but only recently has active research been done into its applications. Detonation based engines have received much attention in the last two decades because of its simple design and potential benefits to the aerospace industry. It is then the goal of this study to provide a background into detonation theory and application and establish the basis for future detonation based research at Embry-Riddle Aeronautical University. In this paper we will discuss the experimental aspects of building, testing, and analysis of a pulsed detonation tube …