Aerodynamics and Fluid Mechanics Commons^™

Novel Airframe Design For The Dual-Aircraft Atmospheric Platform Flight Concept, Eric Michael Mckee

Doctoral Dissertations and Master's Theses

A high-altitude, long-endurance unmanned aerial airframe was designed for the innovative Dual-Aircraft Atmospheric Platform flight concept that exploits stratospheric wind velocity gradients to remain aloft indefinitely. Classical aircraft preliminary design techniques and high-fidelity tools were used to establish a baseline configuration.

Performance characteristics of numerous airfoil profiles were evaluated with two-dimensional flow software in an effort to determine the best-candidate airfoil for the unique application. Vortex-Lattice method tools were used to investigate the sensitivity of three-dimensional design parameters upon overall vehicle aerodynamic performance and determine both static and dynamic stability characteristics of the airframe. Performance capabilities of the finalized airframe …

Distributed Forcing On A 3d Bluff Body With A Blunt Base, An Experimental Active Drag Control Approach, Ethan Bruce Erlhoff

Master's Theses

This paper seeks to explore the effects of an active drag control method known as distributed forcing on a 3D bluff body with a blunt base. The 9.5 x 15.25 x 3 inch aluminum model constructed for this experiment has an elliptically shaped nose and rectangular aft section. The model is fitted with four, 12 Volt fans, forcing the freestream air into and out of 1 mm thick slots on the upper and lower trailing edges. The forcing is steady in time, held at a constant forcing velocity though all Reynolds numbers, but varies roughly sinusoidally in the spanwise direction …

Confined Mixing Of Multiple Transverse Jets, Allen J. Bishop

Master's Theses

The mixing performance of multiple transverse jets has been evaluated experimentally. Measurement techniques included laser Doppler velocimetry and planar laser induced fluorescence. Basic findings are consistent with results presented in literature for single jet mixing behavior. Mixing performance has been compared to literature for the single jet case and the Holdeman parameter has been re-evaluated for effectiveness at low jet numbers. A single jet in a confined crossflow was found to have a local minimum at B(d⁄D) = 0.721. Results for two jets indicate monotonically decreasing unmixedness for the range of conditions tested, with no local optimum apparent. Data for …

Novel Discretization Schemes For The Numerical Simulation Of Membrane Dynamics, Kyle F. Kolsti

Theses and Dissertations

Motivated by the demands of simulating flapping wings of Micro Air Vehicles, novel numerical methods were developed and evaluated for the dynamic simulation of membranes. For linear membranes, a mixed-form time-continuous Galerkin method was employed using trilinear space-time elements, and the entire space-time domain was discretized and solved simultaneously. For geometrically nonlinear membranes, the model incorporated two new schemes that were independently developed and evaluated. Time marching was performed using quintic Hermite polynomials uniquely determined by end-point jerk constraints. The single-step, implicit scheme was significantly more accurate than the most common Newmark schemes. For a simple harmonic oscillator, the scheme …

The Characterization Of Material Properties And Structural Dynamics Of The Manduca Sexta Forewing For Application To Flapping Wing Micro Air Vehicle Design, Ryan P. O'Hara

Theses and Dissertations

The Manduca Sexta species of moth serves as a source of biological inspiration for the future of micro air vehicle flapping flight. The ability of this species to hover in flapping flight has warranted investigation into the critical material, structural, and geometric properties of the forewing of this biological specimen. A rigorous morphological study of the Manduca Sexta forewing was conducted to characterize the physical and material properties of the biological forewing for the purpose of developing an advanced parametric three dimensional model finite element analysis (FEA) model. This FEA model was tuned to match the experimentally determined structural dynamics …

Freedrop Testing And Cfd Simulation Of Ice Models From A Cavity Into Supersonic Flow, Thomas J. Flora

Theses and Dissertations

Weapon release at supersonic speeds from an internal bay is highly advantageous. For this reason, both experimental and numerical methods were used to investigate store separation from a cavity (L=D=4.5) into Mach 2.94 flow. The experiment used a piezoresistive pressure transducer, Schlieren and high-speed photography for data acquisition. The computational solution used the OVERFLOW solver. A sphere and a Mk-82, scaled to 1:20, were formed using frozen tap water. The sphere model was freedrop tested experimentally and computationally, while the sub-scale store shaped model was freedrop tested experimentally. The total pressure was varied to alter the dynamic response of the …

Analysis Of A Goldschmied Propulsor Using Computational Fluid Dynamics Referencing California Polytechnic's Goldschmied Propulsor Testing, Cory A. Seubert

Master's Theses

The Goldschmied Propulsor is a concept that was introduced in mid 1950's by Fabio Goldschmied. The concept combines boundary layer suction and boundary layer ingestion technologies to reduce drag and increase propulsor efficiency. The most recent testing, done in 1982, left questions concerning the validity of the results. To answer these questions a 38.5in Goldschmied Propulsor was constructed and tested in Cal Poly's 3x4ft wind tunnel. The focus of their wind tunnel investigation was to replicate Goldschmied's original testing and increase the knowledge base on the subject. The goal of this research was to create a computational fluid dynamics (CFD) …

Computational Analysis Of A Wing Oscillator, Ryne Derrick Radermacher

Masters Theses

An analysis of a newly proposed wind power extraction device called a wing oscillator was performed using computational fluid dynamics (CFD). A wing oscillator is a device that consists of two airfoils attached to a central pivot by means of a frame or shaft. Oscillatory motion is produced by controlling the angle of attack of the airfoils as a fluid flow is passed over the device. A robust mathematical scheme was developed to investigate the performance of the wing oscillator and was hooked to the CFD software package FLUENT through User Defined Functions (UDFs). Using the dynamic meshing analysis methods …

Hot-Wire Anemometer For The Boundary Layer Data System, William D. Neumeister

Master's Theses

Hot-wire anemometry has been routinely employed for laboratory measurements of turbulence for decades. This thesis presents a hot-wire anemometer suitable for use with the Boundary Layer Data System (BLDS). BLDS provides a unique platform for in- flight measurements because of its small, self-contained, robust design and flexible architecture. Addition of a hot-wire anemometer would provide BLDS with a sensor that could directly measure flow velocity fluctuations caused by turbulence. Hot-wires are commonly operated in constant-temperature mode for high frequency response, but require a carefully tuned bridge. The constant-voltage anemometer (CVA) uses a simple op-amp circuit to improve frequency response over …

Test And Verification Of Vortex Shedding For A 3d Bluff Body, Paul D. Innes, Charles E. Carlson

Aerospace Engineering

Testing of a 3D bluff body with and without end plate tabs was performed in the California Polytechnic State University 3x4 ft low speed wind tunnel. The C_P values were obtained for the test case with no end plate tabs for speeds of 10, 15, 20, and 30 m/s. It was observed that stronger vortex shedding ocured at the higher speed test cases. The model was shimmed to be at approximately 5° angle of attack in order to obtain symmetrical negative C_P spikes for the top and bottom of the model without tabs. Trends were observed and compared …

Thermal Vacuum Integration For Cal Poly's Space Environments Laboratory, Chelsea Barackman, Steven Jackowski

Aerospace Engineering

The purpose of the senior project is to construct a thermal vacuum by utilizing a preexisting vacuum chamber in the Space Environments Lab, and a donated Advanced Thermal Sciences (ATS) chiller. While a thermal vacuum is already available on campus, building one for the Space Environments Lab would grant undergraduates access to the equipment, allowing a much better understanding of testing methods and procedures in use by the aerospace industry. This paper explains the design and analysis of the thermal vacuum (T-VAC) project as well as the operation and procedures required for the ATS chiller and fill/drain tank. The thermal …

Aerodynamic Test Platform For Human Powered Vehicle (Hpv), Spencer Wangerin, Spencer Lillywhite, Colburn Davis

Mechanical Engineering

The Aerodynamic Test Platform (ATP) for the Cal Poly HPV Club is a system that was designed by Cal Poly mechanical engineering students to measure aerodynamic characteristics of a human-powered vehicle (HPV). The HPV team desired a system that could quantify the lift, drag, and other aerodynamic qualities of a full scale HPV at various orientations in oncoming airflow. Established methods for determining aerodynamic characteristics include computational fluid dynamics (CFD) and wind tunnel testing of scaled models. The ATP was devised to simulate the test results given by a full-scale wind tunnel without requiring a wind tunnel large enough to …

Heat, Mass And Force Flows In Supersonic Shockwave Interactions, John Michael Dixon

UNLV Theses, Dissertations, Professional Papers, and Capstones

There is no cost effective way to deliver a payload to space and, with rising fuel prices, currently the price to travel commercially is also becoming more prohibitive to the public. During supersonic flight, compressive shock waves form around the craft which could be harnessed to deliver an additional lift on the craft. Using a series of hanging plates below a lifting wing design, the total lift generated can be increased above conventional values, while still maintaining a similar lift-to-drag ratio. Here, we study some of the flows involved in supersonic shockwave interaction. This analysis uses ANSYS Fluent Computational Fluid …

Section Abstracts: Aeronautical And Aerospace Sciences

Virginia Journal of Science

Abstracts of the Aeronautical and Aerospace Sciences Section for the 90th Annual Meeting of the Virginia Academy of Science, May 23-25, 2015. Norfolk State University, Norfolk, Virginia.

High-Fidelity Modeling Of Airfoil Interaction With Upstream Turbulence, Jacob Brodnick

Doctoral Dissertations and Master's Theses

To supplement past research on low speed unsteady airfoil responses to upstream disturbances, this work proposes and investigates a method to generate a turbulent momentum source to be convected downstream and interact with an SD7003 airfoil in a high-fidelity numerical simulation. A perturbation velocity field is generated from a summation of Fourier harmonics and applied to the forcing function in the momentum terms of the Navier Stokes Equations. The result is a three-dimensional, divergence-free, convected turbulent gust with applied statistical parameters. A parametric study has been done in 2D and 3D comparing the resultant flow fields and airfoil interactions for …

Evaluation Of The Thorax Of Manduca Sexta For Flapping-Wing Micro Air Vehicle Applications, Alex C. Hollenbeck

Theses and Dissertations

The tobacco hornworm hawkmoth (Manduca sexta) provides an excellent model from which to garner knowledge pertaining to the development of a Flapping Wing Micro Air Vehicle (FWMAV). Insect-sized FWMAVs will be used by the future warfighter for reconnaissance, nuclear/chemical/biological hazard sensing, and targeting. One of the major challenges facing FWMAV developers is the energetically demanding nature of low Reynolds flapping flight. Investigating the Manduca sexta thorax/wing flapping mechanism as a mechanical system will provide insight into its inherent efficiency. This thesis examined the energetics of the thorax under static loading and dynamic loading using an innovative load-application technique. It was …

Boundary Layer Measurements In The Trisonic Gas-Dynamics Facility Using Particle Image Velocimetry With Co₂ Seeding, Daniel B. Wolfe

Theses and Dissertations

Particle image velocimetry (PIV) is utilized with solid carbon dioxide (CO₂) seeding material to conduct boundary layer measurements in the test section of the Air Force Research Laboratory's Trisonic Gas-dynamics Facility (TGF), which has a 24 inch by 24 inch cross-section. Freestream velocity was set at Mach 0.3, Mach 0.5, or Mach 0.8 while stagnation pressure ranged from 500 to 2400 pounds per square foot (psf). High pressure liquid CO₂ was directed through expansion nozzles into shroud tubes which led to solidified particles in the wind tunnel stagnation chamber. Two different sets of shroud tubes were used …

Computational Analysis And Characterization Of Rc-135 External Aerodynamics, Michael G. Chenery

Theses and Dissertations

Both the RC-135V/W Rivet Joint (RJ) and the RC-135U Combat Sent (CS) aircraft are United States Air Force (USAF) electronics reconnaissance platforms. The RJ is the USAF's standard airborne signals intelligence (SIGINT) gathering platform, while the CS is designed to collect technical intelligence on adversary radar emitter systems. Both aircraft are extensively modified C-135's characterized by protruding cheek fairings along the sides of the fuselage forward of the wings as well as the addition of numerous antennas along the top and bottom of the fuselage. The major distinguishing feature between the two variants is the nose radome, wherein the RJ …

Validation Of The Chemistry Module For The Euler Solver In Unified Flow Solver, William C. Humphrey Jr.

Theses and Dissertations

In the world of computational fluid dynamics (CFD), three main types of flow regimes exist: continuum, rarified, and free molecular. Of these regimes, the rarified regime is the most difficult to model because the continuum equations don't apply and using the Boltzmann equation is too computationally expensive to use. The Unified Flow Solver (UFS) is currently being developed to solve this problem by using the kinetic continuum Euler equations where valid, and only using the Boltzmann equation where necessary, thus reducing the computational cost. The use of the kinetic Euler equations helps to aid in the coupling of the Euler …

Reynolds Number Effects On Thrust Coefficients And Piv For Flapping Wing Micro Air Vehicles, John P. Tekell

Theses and Dissertations

For the last several years the Air Force Institute of Technology (AFIT) has conducted research in aerodynamics for flapping wing micro air vehicles (MAVs). The focus of this research was to augment this effort by measuring thrust, velocity, and torque in tanks of water and glycerin using a scale and a reaction torque cell. The results for different flapping mechanisms are compared to a rotating propeller with the goal of elucidating the design trade space between rotorcraft and flapping wings at Reynolds numbers less than 100,000. In addition, flow visualization and quantitative velocity data were captured in the wake of …

Experimental Investigation Of A 2-D Air Augmented Rocket: High Pressure Ratio And Transient Flow-Fields, Josef S. Sanchez

Master's Theses

A 2-D Air Augmented Rocket, the Cal Poly Air Augmented Rocket (CPAAR) Test Apparatus operating as a mixer-ejector was tested to investigate high stagnation pressure ratio and transient flow fields of an ejector. The primary rocket ejector was supplied with high pressure nitrogen at a maximum chamber pressure of 1758 psia and a maximum mass flow rate of 1.4 lb/s. The secondary flow air was entrained from a fixed volume plenum chamber producing pressures as low as 3.3 psia. The maximum total pressure ratio achieved was 221. The original CPAAR apparatus was rebuilt re-instrumented and capability expanded. A fixed volume …

Effect Of End-Plate Tabs On Drag Reduction Of A 3d Bluff Body With A Blunt Base, Jarred Michael Pinn

Master's Theses

This thesis involves the experimental testing of a bluff body with a blunt base to evaluate the effectiveness of end-plate tabs in reducing drag. The bluff body is fitted with interchangeable end plates; one plate is flush with the rest of the exterior and the other plate has small tabs protruding perpendicularly into the flow. The body is tested in the Cal Poly 3ft x 4ft low speed wind tunnel. Testing is conducted in three phases.

The first phase was the hot-wire measurement of streamwise velocity of the near wake behind the bluff body. An IFA300 thermal anemometry system with …

Experimental Investigation Of Suction Slot Geometry On A Goldschmied Propulsor, Nicole M. Thomason

Master's Theses

The Goldschmied Propulsor concept combines boundary layer suction and boundary layer ingestion to improve propulsive efficiency and reduce drag on an axisymmetric body. This investigation of a Goldschmied Propulsor aimed to determine influential characteristics of the suction slot geometry to aid in better slot geometry design and to decrease the suction flow requirements for maintaining attached flow over the entire model surface. The Propulsor model was 38.5 inches in length with a max diameter of 13.5 inches. Three suction slot geometries were investigated with the addition of aluminum cusps to the slot entrance. The cusps varied in the distance they …

High Performance Modeling Of Atmospheric Re-Entry Vehicles, Alexandre Martin, Leonardo C. Scalabrin, Iain D. Boyd

Mechanical Engineering Faculty Publications

Re-entry vehicles designed for space exploration are usually equipped with thermal protection systems made of ablative material. In order to properly model and predict the aerothermal environment of the vehicle, it is imperative to account for the gases produced by ablation processes. In the case of charring ablators, where an inner resin is pyrolyzed at a relatively low temperature, the composition of the gas expelled into the boundary layer is complex and may lead to thermal chemical reactions that cannot be captured with simple flow chemistry models. In order to obtain better predictions, an appropriate gas flow chemistry model needs …

Modeling Of Heat Transfer Attenuation By Ablative Gases During The Stardust Re-Entry, Alexandre Martin, Iain D. Boyd

Mechanical Engineering Faculty Publications

The great majority of modern space vehicles designed for planetary exploration use ablative materials to protect the payload against the high heating environment experienced during re-entry. In order to properly model and predict the aerothermal environment of the vehicle, it is imperative to account for the gases produced by ablation processes. In the case of charring ablators, where an inner resin is pyrolyzed at a relatively low temperature, the composition of the gas expelled into the boundary layer is complex and may lead to thermal chemical reactions that cannot be captured with simple flow chemistry models. In order to obtain …

Effect Of Applied Magnetic Field On Shock Boundary Layer Interaction, Ovais U. Khan, Alexandre Martin

Mechanical Engineering Faculty Publications

The governing magneto-hydrodynamic (MHD) equations contain classical fluid dynamics equations along with coupled Maxwell’s magnetic induction equations. These equations model both advection and diffusion effects of electromagnetic field. However, available literature indicates that some previous investigations neglect the diffusion of magnetic field and considered only ideal MHD equations for modeling a typical MHD problem. In this work, the effects of magnetic field diffusion term also known as viscous magnetic term have been investigated over flow structure. Low magnetic Reynolds number approximation and ideal full MHD set of equations have been considered and solved using a four-stage modified Runge-Kutta scheme augmented …

Cfd Study On Aerodynamic Effects Of A Rear Wing/Spoiler On A Passenger Vehicle, Mustafa Cakir

Mechanical Engineering Master's Theses

Aerodynamic characteristics of a racing car are of significant interest in reducing car-racing accidents due to wind loading and in reducing the fuel consumption. At the present, modified car racing becomes more popular around the world. Sports cars are most commonly seen with spoilers, such as Ford Mustang, Subaru Impreza, and Chevrolet Corvette. Even though these vehicles typically have a more rigid chassis and a stiffer suspension to aid in high-speed maneuverability, a spoiler can still be beneficial. One of the design goals of a spoiler is to reduce drag and increase fuel efficiency. Many vehicles have a fairly steep …

Surface Measurements And Predictions Of Full-Coverage Film Cooling, Gregory Natsui

Electronic Theses and Dissertations

Full-coverage film cooling is investigated both experimentally and numerically. First, surface measurements local of adiabatic film cooling effectiveness and heat transfer augmentation for four different arrays are described. Reported next is a comparison between two very common turbulence models, Realizable k-ε and SST k-ω, and their ability to predict local film cooling effectiveness throughout a full-coverage array. The objective of the experimental study is the quantification of local heat transfer augmentation and adiabatic film cooling effectiveness for four surfaces cooled by large, both in hole count and in non-dimensional spacing, arrays of film cooling holes. The four arrays are of …

Agglomeration, Evaporation And Morphological Changes In Droplets With Nanosilica And Nanoalumina Suspensions In An Acoustic Field, Erick Tijerino

Electronic Theses and Dissertations

Acoustic levitation permits the study of droplet dynamics without the effects of surface interactions present in other techniques such as pendant droplet methods. Despite the complexities of the interactions of the acoustic field with the suspended droplet, acoustic levitation provides distinct advantages of controlling morphology of droplets with nanosuspensions post precipitation. Droplet morphology is controlled by vaporization, deformation and agglomeration of nanoparticles, and therefore their respective timescales are important to control the final shape. The balance of forces acting on the droplet, such as the acoustic pressure and surface tension, determine the geometry of the levitated droplet. Thus, the morphology …

Thermal Stability Characteristics Of Fisher-Tropsch And Hydroprocessed Alternative Aviation Fuels In A Fixed Bed Reactor, Sergio Quintero

Electronic Theses and Dissertations

Growing prices, limited supply, and public concern about greenhouse gases associated with crude-derived jet fuels have led to development of renewable alternatives which must be compatible with the worldwide civilian and military aviation infrastructure, which were designed for operation with Jet-A/JP-8. Any alternative fuel should not have negative effects on the aircraft engines and fuel systems, especially from a thermal stability perspective, since any adverse effect of the physical properties, and chemical composition, including existence of trace elements, of those fuels may only be revealed after extensive operation, resulting in higher life-cycle maintenance and operation costs. This study considered four …