Aerodynamics and Fluid Mechanics Commons^™

Extending The Essentially Entropic Lattice Boltzmann Method To Three-Dimensional Turbulent Flows, Michael Derderian

Discovery Day - Daytona Beach

The Entropic Lattice Boltzmann Method (EELBM) has demonstrated strong numerical stability and accuracy for two-dimensional simulations, particularly at higher resolutions where the entropic formulation introduces only minimal stabilizing turbulent viscosity and eventually converges to the Lattice Bhatnagar–Gross–Krook (LBGK) formulation. This built-in stabilization can be interpreted as an implicit large-eddy simulation (LES) model, allowing EELBM to capture complex turbulent behavior without requiring explicit subgrid-scale closures. While these advantages have been thoroughly validated in 2D, understanding how the entropic constraint regulates dissipation in three dimensions is essential for assessing EELBM’s suitability for practical, turbulence-dominated applications. This work focuses on the development and …

Navier Stokes Pressure Drop Derivation, Brayden Benedetti, Gedaliah Dimbert, Jaden Turobiner

Discovery Day - Daytona Beach

Accurate prediction of pressure losses in propellant and fluid feed systems is essential for reliable design and operation of aerospace and industrial flow networks. This project presents a systematic derivation of a practical pressure drop calculator for a feed system using isopropyl alcohol, beginning from the fundamental conservation laws and culminating in an engineering-level computational model. Starting with the differential form of the Navier–Stokes equations for incompressible flow, the governing equations are simplified through a series of physically justified assumptions, including steady-state flow, negligible body forces, and fully developed internal flow within circular piping. The resulting momentum balance is reduced …

Application Of Navier Stokes In Cfd, Hayden Kerkhoff, Gavin Palmer, Garret Seckinger

Discovery Day - Daytona Beach

This project investigates the use of 2-Dimensional Computational Fluid Dynamics (CFD) to analyze aerodynamic behavior, then compare data with the numerical solution of the Navier–Stokes equations run by MATLAB. By leveraging open‑source and possible industry CFD platforms—including OpenFOAM and commercial solvers such as ANSYS Fluent and Inventor Professional—the study evaluates how computational methods simulate, optimize, and predict key aerodynamic quantities such as lift, drag, stall angle, and Reynolds number.   The project focuses on modeling an airflow over specific parameters, such as different angles of attacks and ISA Atmospheric Conditions. Parametric variations in density, angle of attack, chord length, and temperature …

Motion With Air Resistance, Gauge Mccain, Jacob Bealefeld, Francesca Wise

Discovery Day - Daytona Beach

The motion of objects moving through air is influenced not only by gravity but also by air resistance, which affects the speed and acceleration of the object over time. This project examines the motion of a falling object by modeling it with an ordinary differential equation that accounts for both gravitational force and a resistive drag force proportional to velocity. Using Newton’s Second Law, a first-order differential equation is derived to describe how the velocity of the object changes as it falls. The solution of this equation demonstrates how the velocity increases initially and gradually approaches a constant value known …

Simulations Of Phugoid Motion Of Jal 123, Dereth J J. Drake Scheuermann

Georgia Journal of Science

Airplanes rely on a balance between the four forces of flight: lift, weight, thrust, and drag. If these forces are balanced, the airplane will remain stable. However, if structurally or systematically compromised, the motion can rapidly become unstable. In the aviation industry, mistakes in repairs and aircraft design can lead to accidents causing the loss of life in some cases. In this article, we will be analyzing what happened 70 Japan Airlines flight 123 and how the flight’s motion deteriorated due to a defective repair. More specifically, we will discuss the aerodynamic effects of phugoid motion and how it developed …

Numerical Method For Strongly Variable-Density Flows At Low Mach Number: Flame-Sheet Regularisation And A Mass-Flux Immersed Boundary Method, Matheus P. Severino, Fernando F. Fachini, Elmer M. Gennaro, Daniel Rodríguez, Leandro F. Souza

Mathematical Modelling and Numerical Simulation with Applications

A low-Mach-number flow, in the laminar regime, has intrinsically two characteristic spatial scales for a given time scale, or two characteristic temporal scales for a given spatial scale, and these dual scales are very different due to the disparity between the flow and acoustic speed. Therefore, low-Mach-number flows impose mathematical and computational challenges in their description. Standard numerical methods for compressible flows, which are typically designed for problems with a single dominant spatial and temporal scale, require alternative approaches, such as preconditioning techniques or solvers tailored for low-Mach-number equations. The present work introduces a simplified fluid dynamics model for flows …

Boiling Flow Estimation For Aero-Optic Phase Screen Generation, Jeffrey W. Utley, Gregery T. Buzzard, Charles A. Bouman, Matthew R. Kemnetz

Faculty Publications

Aero-optic effects due to turbulence can reduce the effectiveness of transmitting light waves to a distant target. Methods to compensate for turbulence typically rely on realistic turbulence data, which can be generated by i) experiment, ii) high-fidelity computational fluid dynamics (CFD), iii) low-fidelity CFD, and iv) autoregressive methods. However, each of these methods has significant drawbacks, including monetary and/or computational expense, limited quantity, inaccurate statistics, and overall complexity. By contrast, the boiling flow algorithm is a simple, computationally efficient model that can generate atmospheric phase screen data with only a handful of parameters. However, boiling flow has not been widely …

Winddensity-Mbir: Model-Based Iterative Reconstruction For Wind Tunnel 3d Density Estimation, Karl J. Weisenburger, Gregery T. Buzzard, Charles A. Bouman, Matthew R. Kemnetz

Faculty Publications

Experimentalists often use wind tunnels to study aerodynamic turbulence, but most wind tunnel imaging techniques are limited in their ability to take non-invasive three-dimensional (3D) density measurements of turbulence. Wavefront tomography is a technique that uses multiple wavefront measurements from various viewing angles to non-invasively measure the 3D density field of a turbulent medium. Existing methods make strong assumptions, such as a spline basis representation, to address the ill-conditioned nature of this problem. We formulate this problem as a Bayesian, sparse-view tomographic reconstruction problem and develop a model-based iterative reconstruction algorithm for measuring the volumetric 3D density field inside a …

Improving The Reliability And Performance Of A Supersonic Indraft Tube Wind Tunnel, Christian J. Kaml

Master's Theses

Access to supersonic testing is increasing in demand, and wind tunnels remain one of the safest and most cost-effective methods for gathering high-speed flow data. Despite being more economical than alternative options, supersonic wind tunnel facilities often require substantial investment to construct, operate, and maintain.

The novel indraft tube tunnel architecture was conceived as a high-speed flow testbed that incorporates features of both Ludwieg tubes and indraft wind tunnels to maintain costs low enough to be accessible even to small universities. This design was first developed and tested in 2018 at California Polytechnic State University, featuring a cost per test …

Turbulent Plenum Jet-Crossflow Validation Via Subgrid Scale Model Variation And Upstream Forcing Under Dynamic Hybrid Rans-Les, Cole W. Mccallum

Mechanical Engineering Undergraduate Honors Theses

In modern gas turbine design, film cooling has become ubiquitous as a method for limiting heat transfer between high temperature gases post-combustion and the surface of downstream blades. This paper validates the use of various computational fluid dynamics techniques in recreating an experiment measuring adiabatic effectiveness over a surface downstream of a compound-angle N2 plenum jet incident on a turbulent-air boundary layer [1]. To do this, both RANS and Dynamic Hybrid RANS-LES (DHRL) methods are implemented and compared to previous research [2]. The latter method is then modified through implementation of a different subgrid scale (SGS) model and through addition …

Numerical Study Of Nutrient Mixing In Trabecular Bone In Microgravity, Disuse And Normogravity, Sagar Gharti

Doctoral Dissertations and Master's Theses

Mechanical loading is known to regulate bone remodeling by driving interstitial fluid flow which stimulates cells and drives nutrient transport within the trabecular network. In microgravity, the absence of mechanical stimulation or loading suppresses convective flow processes, causing diffusion-driven nutrient mixing and renewal, and accelerated bone loss. This thesis investigates how oscillation frequency and trabecular bone density jointly control nutrient mixing and wall shear stress within trabecular cavities.

A computational fluid dynamics (CFD) framework is developed in STAR-CCM+ using a soft-cap oscillation model that mimics cyclic compression. Three idealized trabecular morphologies are simulated across different frequencies to represent microgravity or …

Computational Study Of Rotating Detonation Combustors, Aditya Balasubramaniam

Mechanical and Aerospace Engineering Theses

Rotating detonation combustors (RDCs) are pressure-gain combustion devices that sustain one or more continuously rotating detonation waves, offering potential thermodynamic and performance advantages over conventional deflagration-based systems. Their behavior depends strongly on combustor geometry and operating conditions. Understanding these effects is therefore essential for the design and optimization of practical RDCs. Accordingly, this thesis numerically investigates annular RDCs with two primary objectives: (1) to evaluate the effects of propellant mass flux and (2) to assess the influence of annular width on detonation-wave dynamics and combustor performance.

A finite-volume framework is used to solve the compressible reactive Euler equations with hydrogen–air …

Active Measurement Of A Micron-Order Gap Under High-Speed And High-Temperature Conditions, Andrew Becker

Doctoral Dissertations and Master's Theses

The hypersonic regime poses numerous challenges that researchers face in the development of hypersonic flight vehicles. Due to their excellent thermomechanical properties, ultra-high-temperature ceramics (UHTCs) have risen as a promising solution to act as a protective barrier between the harsh environment and surface materials of these flight bodies. The mechanical operation of a portable hypersonic simulation device was developed in-house and tested at Argonne National Laboratories (ANL) to gather in-situ material response of prospective UHTC samples when exposed to a hypersonic regime. An edge detection-based algorithm was developed and used in LabVIEW to monitor the health and operation of the …

The Spectral Response Of Time-Resolved Piv In A Turbulent Boundary Layer, Peter Manovski, Wagih Abu Rowin, Henry Ng, Paul Gulotta, Matteo Giacobello, Charitha De Silva, Nicholas Hutchins, Ivan Marusic

Student Publications

This study presents the application of time-resolved particle image velocimetry (TR-PIV) to measure the mean and fluctuating velocity components in a turbulent boundary layer (TBL) over an axisymmetric body of revolution. A narrow wall-normal strip of the flow was captured using a synchronised high-speed laser and camera at a recording frequency of up to 80 kHz. The resulting streamwise and wall-normal velocity TR-PIV data were validated against hot-wire anemometry measurements and direct numerical simulations (DNS) of a flat plate under matched flow conditions. The mean flow results showed good agreement between all methods, while the expected attenuation due to the …

Drag Reduction In Ground Vehicles Using A Model Porous Medium, Abdullah Ikram Nabi

Master’s Theses

This research investigates aerodynamic drag reduction on a 25° Slanted Ahmed Body (SAB) by integrating porous media model rods through combined experimental and computational methods at a Reynolds number of 1.16×10⁴. Two porous media configurations: short rods (6.75% of the model height) and long rods (20.0% of the model height), both featuring cylindrical rods with 80% porosity, were systematically compared against a baseline SAB. In-depth analyses were performed to investigate the wake flow topology, recirculation region characteristics, pressure coefficient distribution, Reynolds stress distributions and drag coefficient. Experimental investigations employed particle image velocimetry for precise flow visualization, while Reynold Averaged Navier-Stokes …

Investigation Of A Busemann Intake At Negative Angle Of Attack, Mark E. Noftz, Andrew N. Bustard, Nicholas J. Bisek, Thomas J. Juliano, Joseph S. Jewell

Publications

A high-speed, shape-transitioned, inward-turning intake was tested in Purdue’s Boeing/AFOSR Mach 6 Quiet Tunnel. The inlet model, called the Indiana Inlet (INlet), had a total contraction ratio of 4.68:1 and a design point of Mach 6 at 0° angle of attack. The model was outfitted with a suite of high-frequency pressure transducers, and the external flowfield was imaged with high-speed schlieren photography. The INlet was tested under low freestream disturbance levels for a variety of freestream unit Reynolds numbers and at-4° angle of attack. An unsteady shockwave near the leading edge of the inlet forebody, indicative of boundary layer separation, …

Impact Of Weather Systems On Uav Parameters Using Computational Fluid Dynamics, Saif Aljuhaishi, Yaseen K. Al-Timimi, Basim I. Wahab

Karbala International Journal of Modern Science

Since drones cannot fly in any kind of weather, they are not safe for time-sensitive activities. The study examines how the passage of weather systems in Iraq leads to the ban on drone flights, and how these weather conditions impact the aerodynamic forces of the drone. Hourly climate data for the study area were obtained from ECMWF ERA5 and CAMS in NetCDF format for four climate stations (Erbil, Baghdad, Rutbah, and Basrah). A ScanEagle drone was chosen for this study. The Python programming language was used to perform mathematical operations to calculate the ban on drone flights. ArcGIS 10.8 was …

Blade Design And Validation Of Hydrokinetic Turbine To Harvest Water Current Energy, Setare Sadeqi

LSU New Orleans Theses and Dissertations

The innovative aspect of this research lies in the careful integration of cutting-edge technologies throughout the entire process of designing, fabricating, and testing the carbon fiber propeller for the 3-bladed horizontal axis ocean current turbine (OCT). SolidWorks software played a pivotal role in the initial design phase, enabling a meticulous and precise modeling of the propeller's geometry. The utilization of SolidWorks allowed for a detailed exploration of various design parameters, ensuring that the propeller's structure and form were optimized for performance in ocean current conditions. Moving beyond the realm of virtual design, the choice of carbon fiber as the fabrication …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Development Of On-The-Fly Quasi-Steady State Approximation For Chemical Kinetics In Cfd, Abhinav Balamurugan

Doctoral Dissertations and Master's Theses

This study analyzes the feasibility of On-The-Fly Quasi-Steady-State Approximation (OTF-QSSA) application for solving chemical kinetics within Computational Fluid Dynamics (CFD) simulations, aiming to reduce the computational demand of detailed mechanisms. An algorithm that dynamically identifies and designates Quasi-Steady-State (QSS) species at specific grid locations and instances during the simulation was developed. With this information, our method pseudo-delays the advancement of concentrations for these QSS species—effectively setting their rate of concentration change to zero for a set number iteration before updating using the detailed mechanism and thereby omitting the computationally intensive processes typically required for their calculation during those skipped iteration. …

Development Of Advanced Instrumentation For High-Enthalpy Flow Characterization For The Onr-Uta Arc-Jet ”Leste” Facility, Ian Raybon

Mechanical and Aerospace Engineering Dissertations - Archive

Sustained hypersonic flight is an exceedingly challenging task comprised of a myriad of complex physical processes. At hypersonic speeds, which is defined by the presence of unique phenomena like high-temperature nonequilibrium flow, viscous and vorticity interactions, and thin shock layers, which are not seen in supersonic, transonic, or subsonic vehicles, the vehicle design is principally driven by the high levels of aerodynamic heating caused by the conversion of kinetic energy to internal energy. Gaining an understanding of how these physical processes interact with each other is required to develop a design methodology for this class of vehicles. Arc-jet wind tunnels …

Dynamics Of A 3-D Inlet/Isolator Measured With Fast Pressure-Sensitive Paint, Andrew N. Bustard, Mark E. Noftz, Mitsugu Hasegawa, Hirotaka Sakaue, Joseph S. Jewell, Nicholas J. Bisek, Thomas J. Juliano

Publications

Fast pressure-sensitive paint (PSP) was applied to an inlet/isolator designed using the Osculating Internal Waverider Inlet with Parallel Streamlines (OIWPS) method. The dorsal isolator surface pressure was measured using anodized-aluminum PSP through transparent cast acrylic that makes up the ventral portion of the isolator. Temperature-sensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at Re = 8.5 ×106 /m and 10.2 ×106 /m in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel (ANDLM6QT) under conventional noise conditions. Flow phenomena, such as shocks originating in the inlet and flow separation at the …

Numerical Study Of Owls' Leading-Edge Serrations, Asif Shahriar Nafi, Nikolaos Beratlis, Elias Balaras, Roi Gurka

Physics and Engineering Science

Owls' silent flight is commonly attributed to their special wing morphology combined with wingbeat kinematics. One of these special morphological features is known as the leading-edge serrations: rigid miniature hook-like patterns found at the primaries of the wings' leading-edge. It has been hypothesized that leading-edge serrations function as a passive flow control mechanism, impacting the aerodynamic performance. To elucidate the flow physics associated with owls' leading-edge serrations, we investigate the flow-field characteristic around a barn owl wing with serrated leading-edge geometry positioned at 20° angle of attack for a Reynolds number of 40 000. We use direct numerical simulations, where …

Experimental And Computational Aerodynamic Studies Of Axially-Oriented Low-Fineness-Ratio Cylinders, Forrest Miller

Mechanical & Aerospace Engineering Theses & Dissertations

For the successful completion of atmospheric entry, descent, and landing (EDL) missions, a body geometry must be selected which provides favorable dynamic aerodynamic properties. The types of experimental facilities capable of collecting information on these properties are limited; however, their numbers are growing thanks to the continued work by the aerodynamics community. NASA Langley Research Center (LaRC) is conducting dynamic aerodynamic testing using a subsonic magnetic suspension and balance system (MSBS), with the end goal of implementing a supersonic MSBS facility at NASA Glenn Research Center. MSBSs are also currently used at the Institute of Fluid Science (IFS) at Tohoku …

Numerical Study Of Owls’ Leading-Edge Serrations, Asif Shahriar Nafi

Electronic Theses and Dissertations

The silent flight ability of owls is often attributed to their unique wing morphology and its interaction with their wingbeat kinematics. Among these distinctive morphological features, leading-edge serrations stand out – these are rigid, miniature, hook-like patterns located at the leading edge of the primary feathers of their wings. It had been hypothesized that these leading-edge serrations serve as a passive flow control mechanism, influencing the aerodynamic performance and potentially affecting the boundary layer development over the wing, subsequently influencing wake flow dynamics. Despite being the subject of research spanning multiple decades, a consensus regarding the aerodynamic mechanisms underpinning owls’ …

Stratospheric Glider Measurements Of Atmospheric Parameters, Anisa Haghighi

Theses and Dissertations--Mechanical and Aerospace Engineering

In June 2021 a series of high altitude flights were conducted in Spaceport America, NM, using a balloon launched Uncrewed Aircraft System (UAS) to assess its capability to conduct measurements of various atmospheric properties and study turbulence in the troposphere and lower stratosphere. This UAS descends using an automated flight trajectory. The instruments aboard included a NASA-developed infrasonic microphone to evaluate its remote turbulence detection capabilities and a five-hole probe capable of measuring the in situ wind vector. Also on board were temperature, humidity and wind profile sensors. This document focuses on the atmospheric properties measured at high altitudes, the …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Design Of An Internal Osculating Waverider Intake, Mark E. Noftz, Andrew J. Shuck, Joseph S. Jewell, Jonathan Poggie, Andrew N. Bustard, Thomas J. Juliano, Nicholas J. Bisek

Publications

The design of an inward-turning, high-speed, three-dimensional streamline traced intake is presented from osculating axisymmetric theory. To satisfy the osculating intake design criteria, a stitched Busemann diffuser and Internal Conical Flow-A solution is used as the basic isentropic compressive streamline. This new contour provides efficient compression, high flow uniformity, and straight leading edge shocks of equal strength. Additionally, a novel method for constructing the inlet cowl is presented. The combined process leads to a new method of high-speed intake design. A generic shape-transitioned intake is constructed and named the Indiana Inlet for the Indiana universities that contributed to the project. …

Direct Simulation And Reduced-Order Modeling Of Premixed Flame Response To Acoustic Modulation, Zheng Qiao

Theses and Dissertations

This dissertation introduces a general, predictive and cost-efficient reduced-order modeling (ROM) technique for characterization of flame response under acoustic modulation. The model is built upon the kinematic flame model–G-equation to describe the flame topology and dynamics, and the novelties of the ROM lie in i) a procedure to create the compatible base flow that can reproduce the correct flame geometry and ii) the use of a physically-consistent acoustic modulation field for the characterization of flame response. This ROM addresses the significant limitations of the classical kinematic model, which is only applicable to simple flame configurations and relies on ad-hoc models …

Recent Analytic Development Of The Dynamic Q-Tensor Theory For Nematic Liquid Crystals, Xiang Xu

Mathematics & Statistics Faculty Publications

Liquid crystals are a typical type of soft matter that are intermediate between conventional crystalline solids and isotropic fluids. The nematic phase is the simplest liquid crystal phase, and has been studied the most in the mathematical community. There are various continuum models to describe liquid crystals of nematic type, and Q-tensor theory is one among them. The aim of this paper is to give a brief review of recent PDE results regarding the Q-tensor theory in dynamic configurations.