Aerodynamics and Fluid Mechanics Commons^™

Project Chimaera: Development Of A Tessellated Tetrahedral Truss Structure For Adaptive Multi-Regime Morphing Wing Technology, Evan Meyer, Eric Rodarte, Maximo Failla, Joshua Shuster, Jackson G. Schuler

Discovery Day - Daytona Beach

Project Chimaera: Physical Assembly of tessellated tetrahedral wing for Multi-Regime Flight. Modern Aircrafts lose aerodynamic efficiency because they are primarily made utilizing fixed wings which are designed for a single optimal flight condition. This forces an aircraft’s performance to become compromised across various speed maneuvers and flight regimes. Project Chimaera addresses this limitation through the development of a morphing wing capable of dynamically changing its geometry extensively during flight to allow an aircraft to travel between subsonic, supersonic, and hypersonic speeds. Whereas traditional wings rely on wing flaps and other flight controls; Project Chimaera addresses the limitation of flight controls …

Effect Of Nozzle Pressure Ratio On Thrust And Flow Behavior In A Supersonic De Laval Nozzle, Esha Jain

Doctoral Dissertations and Master's Theses

Supersonic nozzles operate across a range of flow regimes. While an ideally expanded condition yields optimal thrust, practical propulsion systems rarely operate at this design point due to variations in altitude and engine operating conditions. As a result, nozzles frequently operate in off-design conditions. In overexpanded regime, where the exit pressure is lower than the ambient pressure, shock-induced separation may occur within the divergent section of the nozzle, potentially degrading nozzle performance. Understanding the aerodynamic behavior of nozzles operating under off-design conditions is therefore important for improving propulsion system performance and stability. In particular, direct thrust measurements provide a key …

Investigation Of The Impact Of The Shape Of The Wings On Formula E Racing Car Performance: Enhancements For Optimal Aerodynamics, Ednie Marthe Adlaikah Jozil

Honors Undergraduate Theses

The aerodynamic performance of a Formula E chassis significantly dictates its overall race efficiency, directly impacting crucial parameters such as battery range and thermal management. This thesis investigates the external aerodynamics of the baseline Gen 2 Formula E car and evaluates the performance gains of two novel aerodynamic packages: a "Fully Modified" configuration and a "Flat Rear Wing" design. Computational Fluid Dynamics (CFD) simulations were conducted to analyze drag coefficients (Cd), downforce generation, and vehicle wake structures at race-relevant free-stream velocities (e.g., 37 m/s and 89 m/s). To ensure numerical robustness, the computational setup was validated using a smooth sphere …

Wind Tunnel Instrumentation And Testing, Nicholas Marek, Abraham Mezera, Laura Jin, Hayden Smith, Curtis Cook

Student Scholar Symposium

The Raymond B. Jones College of Engineering was contacted by an automotive engineering firm seeking to use the college’s wind tunnel for gathering data on the aerodynamic performance of a proprietary prototype automotive door. Specifically, the client requested the quantification of the drag coefficient of the model at extreme wind speeds. The drag coefficient, a dimensionless number that quantifies the resistance of a specific geometric shape to airflow, will be a valuable datapoint for the client’s design iteration. Due to the sensitive nature of their work, the client has wished to remain anonymous. RBJCOE professors tasked a senior design team …

Exploration Of Physics-Informed Grid Generation Technique For Wall-Modeled Les Using Eagle3d, Dominic Schneider

Doctoral Dissertations and Master's Theses

Wall-Modeled Large Eddy Simulation (WMLES) is an area of interest due to its ability to lower computational costs of LES. Even with the application of wall models, LES still proves to have practicality issues when it comes to use in industry, due to the expertise, time, and computational resources required. A novel technique for generating a lean, physics based WMLES grid is described.

The technique utilizes a RANS solution to extract turbulence information, user-specified values related to resolution of turbulent energy levels, acoustics waves, and shock waves, to generate a point cloud for producing a lean WMLES grid with in-house …

Active Measurement Of A Micron-Order Gap Under High-Speed And High-Temperature Conditions, Andrew Becker

Doctoral Dissertations and Master's Theses

The hypersonic regime poses numerous challenges that researchers face in the development of hypersonic flight vehicles. Due to their excellent thermomechanical properties, ultra-high-temperature ceramics (UHTCs) have risen as a promising solution to act as a protective barrier between the harsh environment and surface materials of these flight bodies. The mechanical operation of a portable hypersonic simulation device was developed in-house and tested at Argonne National Laboratories (ANL) to gather in-situ material response of prospective UHTC samples when exposed to a hypersonic regime. An edge detection-based algorithm was developed and used in LabVIEW to monitor the health and operation of the …

Computational Fluid Dynamics Analysis Of A Turbine Blade, Luis Luna, Fabiha Samiha

Publications and Research

In Aerospace engineering, the use of computer-aided design (CAD) software, such as SolidWorks, is crucial when designing and validating high-performance parts. SolidWorks provides a valuable tool for simulating computational fluid dynamics (CFD), allowing engineers to analyze and visualize how parts behave under real-world aerodynamic conditions.

One such part is a turbine blade, an airfoil-shaped component inside a jet engine that compresses and redirects airflow to generate thrust. This study aims to perform aerodynamic testing of a single turbine blade design while evaluating SolidWorks' ability to simulate external flow conditions. By visualizing velocity profiles, pressure distribution, and vortex formation, the simulation …

Drag Reduction In Ground Vehicles Using A Model Porous Medium, Abdullah Ikram Nabi

Master’s Theses

This research investigates aerodynamic drag reduction on a 25° Slanted Ahmed Body (SAB) by integrating porous media model rods through combined experimental and computational methods at a Reynolds number of 1.16×10⁴. Two porous media configurations: short rods (6.75% of the model height) and long rods (20.0% of the model height), both featuring cylindrical rods with 80% porosity, were systematically compared against a baseline SAB. In-depth analyses were performed to investigate the wake flow topology, recirculation region characteristics, pressure coefficient distribution, Reynolds stress distributions and drag coefficient. Experimental investigations employed particle image velocimetry for precise flow visualization, while Reynold Averaged Navier-Stokes …

Blade Design And Validation Of Hydrokinetic Turbine To Harvest Water Current Energy, Setare Sadeqi

LSU New Orleans Theses and Dissertations

The innovative aspect of this research lies in the careful integration of cutting-edge technologies throughout the entire process of designing, fabricating, and testing the carbon fiber propeller for the 3-bladed horizontal axis ocean current turbine (OCT). SolidWorks software played a pivotal role in the initial design phase, enabling a meticulous and precise modeling of the propeller's geometry. The utilization of SolidWorks allowed for a detailed exploration of various design parameters, ensuring that the propeller's structure and form were optimized for performance in ocean current conditions. Moving beyond the realm of virtual design, the choice of carbon fiber as the fabrication …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Experimental And Numerical Analysis Of Laminar And Transitional Flow Through Annular Corrugated Pipes, Joseph Russell Sargent

Theses and Dissertations

This dissertation presents studies on pressure loss through annular corrugated pipes to determine a friction factor coefficient using nitrogen. Ten different corrugated pipes’ geometries were evaluated via testing and experimentation. The ratio of corrugation height to inner diameter varied from 0.233 to 0.333 and the ratio of corrugation pitch to inner diameter varied from 0.181 to 0.446. Nitrogen flow rates between 0.25 to 94.4 standard liters per minute were used, resulting in Reynolds numbers, based on the corrugated pipe inner diameter, from 100 to 23,000. The experimental set-up was validated using smooth-pipe pressure loss measurements and the derived friction factor …

Aerodynamic Design And Analysis Of A Modified 2006 Mazda Miata, William N. Recher

Honors College Theses

Aerodynamic forces developed by automobiles have destabilizing effects at high speed. These forces tend to skew toward a vehicle’s rear which can present safety concerns, especially for rear-wheel-drive automobiles like the Mazda Miata. To address oversteer and high-speed instability, a vehicle’s design can be tailored to bring about aerodynamic balance and improve traction. LiDAR was used to bring the physical automobile into the digital space. Then, a splitter and diffuser were added to reduce the magnitude of the destabilizing forces. Next, the size and shape of the rear-wing required to balance the vehicle was calculated using a combination of parameters …

Optimization Of High-Bypass Turbofan High-Pressure Compressor Blade – A Case Study, Adeel Khalid, Vlad Mandzyuk

The Kennesaw Journal of Undergraduate Research

This research determines the relationship between the High-Pressure Compressor (HPC) rotor blade design variables and compressor pressure ratio of a high bypass turbofan engine. Alterations in the HPC blades span, chord, taper, twist, number, and angle of incidence are performed and their effect on the HPC pressure ratio is observed. The objective is to determine key parameters that could maximize the performance of a high-pressure compressor for a given mission. Physics-based modeling, Computational Fluid Dynamics (CFD), and wind-tunnel testing are performed to compare and validate findings. Physics-based modeling is performed to serve as the benchmark for data obtained through other …

Experimentatal And Numerical Investigation Of Turbojet Engine Performance, Emissions, And Noise/Vibrations Using Jet-A And F24 Fuel, John W. Mcafee Jr

College of Graduate Studies: Theses & Dissertations

Drastic improvement in cost effectiveness of high-power computing resources has generated a great interest numerical simulation to reduce the overhead cost of engine manufacturing, maintenance, and environmental concerns of engine testing. To accomplish this goal, this research presents the differences between military F24 fuel and commercial aviation fuel Jet-A from a thermochemical and engine performance perspective. This experimental data was used to create and validate a numerical model of the engine used in the experiments fueled with both Jet-A and F24 fuels. The experimental data was collected using a research based single stage turbojet engine outfitted with many sensors for …

Depressurization Characteristics Of Steam-Based Reciprocating Vacuum Pump, Hongling Deng

Dissertations

This dissertation introduces a novel vacuum technology that leverages low-pressure saturated steam and cooling-controlled condensation, offering an efficient way to utilize low-grade thermal energy sources like waste heat, steam, or solar energy. At the heart of this technology is a unique duo-chamber vacuum pump system, featuring a reciprocating piston and a heat-conductive wall, designed to generate a vacuum through steam-condensation and cooling processes.

The core of this research lies in developing and validating mechanistic models for the steam-condensation depressurization process, a complex phenomenon involving phase change and transport mechanisms. Prior to this work, these mechanisms were not sufficiently modeled or …

Husker Motorsports Active Drag Reduction System, Creighton Hughes, Evan Killian, Micah Busboom, Aj Johnson, Jude Steffen

Honors Program: Senior Projects (Public)

Formula SAE is a multifaceted competition that involves student teams designing and competing with an open-wheel style race car. There are 5 different dynamic events included in the competition. Each event requires a unique aerodynamic setup to have the best performance possible. This design project focuses on a drag reduction system (DRS) that will improve aerodynamic performance, resulting in faster lap times and increased competitiveness. Key features include a direct electronic actuation mechanism that will allow the rear wing to be adjusted during a race. The benefits of the DRS system, include increased speed, improved handling, and greater fuel efficiency …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical and Aerospace Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

Design And Manufacture Of An Aerodynamic Body That Meets Scaling Law Requirements And Survives Severe G-Load Environment For Free-Flight Testing, Anthony R. Gonzalez

Graduate Theses, Dissertations, and Problem Reports (ETD)

Design and Manufacture of an Aerodynamic Body that Meets Scaling Law Requirements and Survives Severe G-load Environment for Free-Flight Testing

Anthony Gonzalez

Developing scale models to test functionality and ascertain aerodynamic properties is critical before manufacturing full-size products. Through dimensional analysis and similitude, engineers create scale models to test any parameter of interest. This research aims to design a scale model of an aerodynamic body for repeated free-flight testing. The Froude number is the dominant scale model law used to determine the geometric, mass, and inertia scaling laws. A critical requirement for this research is that the model should be …

Foundations For Finite-State Modelling Of A Two-Dimensional Airfoil That Reverses Direction, Jake Michael Oscar Welsh

McKelvey School of Engineering Graduate Student Theses & Dissertations

Current 3-D finite-state wake models are incapable of simulating a maneuver in which the sign of the free-stream velocity changes direction and the rotor enters its own wake -- as might occur in the case of a helicopter which ascends and then descends. It is the purpose of this work to create a 2-D finite-state wake model which is capable of handling changes in free-stream direction as a precursor to development of a 3-D model that can do the same.

The 2-D finite-state model used for reentry modifications is an existing model created by Peters, Johnson, and Karunamoorthy. By the …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

College of Graduate Studies: Theses & Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

Bibliometric Analysis On Artificial Compressibility Method Based Cfd Simulations, Bhavna Hemraj Joshi Miss, Chandrakant R. Sonawane Dr, Priyambada Bada Praharaj Mrs, Anand Kumar Pandey Dr

Library Philosophy and Practice (e-journal)

This bibliometric analysis in this paper aims to study the quantitative progress done in the artificial compressibility (AC) method-based CFD simulation and analyze its potential in solving incompressible flow simulations in computational fluid dynamics smoothly. The sector of CFD is enhancing more and more maturely due to advancements in computing architecture, numerical methods, and simulation tools. There have been various attempts to solve the pressure-velocity coupling issue in the Navier-Stokes equation. The artificial compressibility method (ACM), as opposed to pressure-correction methods, solves the incompressible equation in a non-segregated manner. With the introduction of the ACM, the system of the equation …

Data-Driven Tools Guided By First-Principles For Scale Modeling, Sadegh Poozesh

Progress in Scale Modeling, an International Journal

For decades, traditional scale-modeling techniques have been relying on first-principles models (FPMs). FPMs have been used to find non-dimensional numbers (PIs) and identify normalized underlying forces and energies behind the phenomenon in focus. The two main challenges with FPM-based PIs extraction are finding the relevant PIs and proper correlations between PIs. The emergence and surge of data-driven modeling (DDM) provide a new opportunity to leverage experimental data in model development across scales/plants. In this paper, first, the two mentioned issues in PIs development will be elaborated to reveal the gap, and second, a new insight into scale modeling and similarity …

Nebulizer-Based Systems To Improve Pharmaceutical Aerosol Delivery To The Lungs, Benjamin M. Spence

Theses and Dissertations

Combining vibrating mesh nebulizers with additional new technologies leads to substantial improvements in pharmaceutical aerosol delivery to the lungs across therapeutic administration methods. In this dissertation, streamlined components, aerosol administration synchronization, and/or Excipient Enhanced Growth (EEG) technologies were utilized to develop and test several novel devices and aerosol delivery systems. The first focus of this work was to improve the poor delivery efficiency, e.g., 3.6% of nominal dose (Dugernier et al. 2017), of aerosolized medication administration to adult human subjects concurrent with high flow nasal cannula (HFNC) therapy, a form of continuous-flow non-invasive ventilation (NIV). The developed Low-Volume Mixer-Heater (LVMH) …

Design And Control Techniques Of The Open-Circuit Subsonic Wind Tunnel With Closed Testing Section, Jamshid Yakhshilikov, Jamshid Inoyatkhodjaev

Acta of Turin Polytechnic University in Tashkent

This paper will describe the design and control techniques of the open-circuit subsonic wind tunnel with closed testing section (WT) for study purpose. The goal is to design a WT that can be tested at a wind speed of 30 m/s, where the desired cross-sectional area of the test chamber is 0.5x0.5 m. The pressure drop inside the WT has been calculated in order to select one of the available axial fans from the manufacturer’s catalog, and computational fluid dynamics (CFD) was performed to check the result. In order to obtain a smooth airflow in the test section, a proportional …

Fluid Flow Analysis Of Low-Altitute Agricultural Uav Pesticide Spraying Device, Dan Han

Student Works (2020-2029)

The nozzle is an important part of the drone pesticide spraying device. The quality of the nozzle directly affects the atomization performance. Fan nozzles are widely used in the field of plant protection in agriculture, forestry, pest control, and weed removal. When using drones to spray pesticides, the spraying velocity, the spraying range of the pesticides, and the atomized particle size are all key factors that directly affect the efficiency of pesticide use. This paper uses SOLIDWORKS and ANSYS software to design and simulate. The boundary conditions are kept the same, and the influence of the nozzle's grooving angle (α), …

Analysis Of One Way Valve Mechanism For Wings Of A Flapping Drone, Xinchen Deng

Student Works (2020-2029)

The flapping drone is one type of MAVs which is defined as a miniature unmanned aerial vehicle that is inspired by flying birds and insects. Flapping wings can make a perfect combination of thrust and lift by flapping up and down with full usage of unsteady air. The flapping drone has the advantages of high maneuverability and a special lift generation mechanism. Compared with rotary-wing or fixed-wing MAV, it is smaller, lighter, and has higher flight performance. It can quickly change the flight direction and flight speed by control the flapping frequency and it is the only flight mode that …

Design Of Banner Tow Mechanism For Bush Plane, Kyle Ciarrone, Ivan Martin, Rishabh Gadi, Tyler Brandt

Williams Honors College, Honors Research Projects

The 2019-2020 AIAA DBF objective was to design, build, and test a banner-towing bush plane that carries wooden passengers and luggage. Senior members on the team undertook the creation of the banner tow mechanism subsystem as their senior design project on behalf of the design team due to the challenge of its mechanical design and the aerodynamic considerations regarding its placement and enclosure aboard the aircraft. The competition as well as access to campus resources were canceled due to COVID-19, so full testing and integration of the mechanism was not achieved. However, the engineering design process was experienced from the …

Rocket Motor Nozzle, Corey Hillegass

Williams Honors College, Honors Research Projects

For this honors research and senior design project, the authors will research, analyze, and manufacture a rocket motor nozzle for the Akronauts rocket design team. This research and design project will improve how the rocket design team will decide and manufacture nozzles going forward. The impact of this improvement allows the rocket design team to take steps toward being self-sustaining by manufacturing student designed parts as opposed to commercially bought parts. This will not only be successful in increasing student impact on future designs, but also provides a technical challenge for the authors and will present as an impressive feat …

Space Dynamics Laboratory Payload Challenge: Autonomous Water Sampling Uav, Thomas Wheeler, Zachary Williams, Joseph Stack

Williams Honors College, Honors Research Projects

The following report has been completed over the course of the Fall 2018 and Spring 2019 semesters at The University of Akron by Joseph P. Stack (Aerospace Systems Engineering), Thomas J. Wheeler (Mechanical Engineering) and Zachary M. Williams (Mechanical Engineering). The purpose of this project was to create a payload system for the Akronauts Rocket Design Team to use at the Intercollegiate Rocket Engineering Competition (IREC) Spaceport America Cup. The Competition as a challenge that is sponsored by Space Dynamics Laboratory specifically regarding payload systems. The challenge in very open-ended and allows student to identify their own scientific experiment and …

Computational Study Of Flow Interactions Over A Close Coupled Canard-Wing On Fighter, Setyawan Bekti Wibowo, Sutrisno Sutrisno, Tri Agung Rohmat

International Journal of Aviation, Aeronautics, and Aerospace

There have been many attempts to improve the flying performance of a fighter. By modifying the flow that occurs along the fuselage is expected to improve the performance of the aircraft. One of the indicators of combat aircraft performance is the ability to perform maneuver movement. Adding a canard as forewing on the fighter wing configuration is considered capable of raising the ability in maneuver movement. The use of canard-delta pairs will affect the performance and aerodynamic characteristics of the plane. Wings and canards with delta configuration will make the rolled-up vortex as a lifting force producer on the aircraft. …