Aerodynamics and Fluid Mechanics Commons^™

Improving The Reliability And Performance Of A Supersonic Indraft Tube Wind Tunnel, Christian J. Kaml

Master's Theses

Access to supersonic testing is increasing in demand, and wind tunnels remain one of the safest and most cost-effective methods for gathering high-speed flow data. Despite being more economical than alternative options, supersonic wind tunnel facilities often require substantial investment to construct, operate, and maintain.

The novel indraft tube tunnel architecture was conceived as a high-speed flow testbed that incorporates features of both Ludwieg tubes and indraft wind tunnels to maintain costs low enough to be accessible even to small universities. This design was first developed and tested in 2018 at California Polytechnic State University, featuring a cost per test …

Design And Development Of A Resonance Ignition System Using Gaseous Propellants, Benjamin J. Hoefer

Master's Theses

This work presents the development and experimental evaluation of a resonance igniter (RI) operating with premixed gaseous propellants. Resonance ignition is a non-electrical ignition concept in which an underexpanded jet impinges on a closed-end Hartmann–Sprenger tube (HST), generating cyclic compression and expansion waves that rapidly heat gas near the tube endwall. A modular experimental system was designed and built to investigate resonance ignition using methane–air and methane–oxygen mixtures. The system includes a supplemental configuration that may probe for mixture conditions favorable to ignition, informing RI testing. Pressure and temperature measurements were used to characterize pressure control, mixture pressure ratio (MPR), …

Numerical Study Of Nutrient Mixing In Trabecular Bone In Microgravity, Disuse And Normogravity, Sagar Gharti

Doctoral Dissertations and Master's Theses

Mechanical loading is known to regulate bone remodeling by driving interstitial fluid flow which stimulates cells and drives nutrient transport within the trabecular network. In microgravity, the absence of mechanical stimulation or loading suppresses convective flow processes, causing diffusion-driven nutrient mixing and renewal, and accelerated bone loss. This thesis investigates how oscillation frequency and trabecular bone density jointly control nutrient mixing and wall shear stress within trabecular cavities.

A computational fluid dynamics (CFD) framework is developed in STAR-CCM+ using a soft-cap oscillation model that mimics cyclic compression. Three idealized trabecular morphologies are simulated across different frequencies to represent microgravity or …

Computational Study Of Rotating Detonation Combustors, Aditya Balasubramaniam

Mechanical and Aerospace Engineering Theses

Rotating detonation combustors (RDCs) are pressure-gain combustion devices that sustain one or more continuously rotating detonation waves, offering potential thermodynamic and performance advantages over conventional deflagration-based systems. Their behavior depends strongly on combustor geometry and operating conditions. Understanding these effects is therefore essential for the design and optimization of practical RDCs. Accordingly, this thesis numerically investigates annular RDCs with two primary objectives: (1) to evaluate the effects of propellant mass flux and (2) to assess the influence of annular width on detonation-wave dynamics and combustor performance.

A finite-volume framework is used to solve the compressible reactive Euler equations with hydrogen–air …

Numerical And Experimental Evaluation Of A Simple, Low-Energy Lunar Volatile Separation Technology, Eleanor L. Zimmermann

Dissertations, Master's Theses and Master's Reports

In-situ resource utilization (ISRU) is the practice of finding, extracting, and using the local resources found on extraterrestrial bodies, such as the Moon and Mars. ISRU enables in-situ production of mission consumables—such as rocket fuel and potable water—which will be critical for establishing a sustainable human presence on the Moon, a goal NASA intends to accomplish by 2028 with the Artemis missions. The separation and liquefaction of locally extracted volatiles—such as water, CO₂, and Methane—is an essential component in lunar surface sustainability, but there are very few technologies being developed for this purpose. This report introduces the Radiative …

Flow Field Characterization Of The Hyperreact Vitiated Hypersonic Wind Tunnel, Erik R. Fernandez

Graduate Studies Theses and Dissertations 2026

Reliable interpretation of hypersonic ground-test data requires knowledge of the thermochemical state delivered to the test section, especially in combustion-heated facilities where the gas is chemically altered before nozzle expansion. This thesis investigates the HyperReact vitiated hypersonic wind tunnel using the effective specific-heat ratio, γeff, as an experimentally inferred indicator of the coupled chemical and gas-dynamic behavior of hydrogen-air vitiated flow. HyperReact produces high stagnation temperatures through hydrogen-air combustion before expanding the mixture through interchangeable converging-diverging nozzles. During this expansion, temperature-dependent specific heats, molecular-weight changes, finite-rate chemistry, and internal energy relaxation can modify the relationship between Mach number, pressure ratio, …

Ultrafast Laser Surface Structuring For Wettability Control On Copper, Akshay Arvind Nagvenkar

All Theses

Wettability is a crucial surface property influencing various phenomena, including heat transfer, cell adhesion, and corrosion. Engineering devices can achieve superior performance by precisely manipulating surface wettability. As a result, extensive research has focused on developing surfaces that exhibit either extreme water attraction (superhydrophilic) or strong water repellency (superhydrophobic). Tailoring surface wettability paves the way for numerous applications, such as drag reduction in marine vessels, controlled drug delivery, efficient water collection, advanced liquid transport systems, oil-water separation, anti-corrosion coatings, friction reduction, and self-cleaning materials. Ultrafast laser surface structuring is a promising approach for engineering multifunctional surfaces, effectively modifying material properties …

Qualitative Analysis Of Surface Modification On Wiffleball Aerodynamics, Cole Lanni

Williams Honors College, Honors Research Projects

This project investigated how surface modifications to a Wiffleball affect its aerodynamic behavior, particularly its vertical and horizontal movement when thrown. The study tested the hypothesis that altering surface texture through cutting or sanding would influence airflow and pressure differentials, thereby changing the ball's movement. Six ball conditions: including unmodified, sanded, and various cut patterns were tested using a pitching machine in a controlled indoor environment. Each variation was pitched ten times, and movement was analyzed through measurements of contact points on posterboards and performing statistical testing, specifically ANOVA with Post Hoc analysis. Results indicated that surface modifications significantly increased …

Hybrid Rans-Les Analysis Of Turbulent Flame Under Near Blow-Off Condition In A Multi-Stage Swirl Combustor, Brandon O'Brien

College of Graduate Studies: Theses & Dissertations

Advances in computational resources are making computational fluid dynamics (CFD) increasingly accessible for a variety of engineering applications. However, certain complex problems, such as simulating detailed flame kinetics, remain computationally prohibitive for many users. Developing cost-effective methods to simulate these challenges would greatly benefit applications involving flame dynamics, such as turbine engines or industrial burners. This study investigates the effect of main stage swirler intensity on near lean blow-off characteristics in a multi-staged swirl combustor using Ansys Fluent. The hybrid RANS-LES turbulence model, Stress Blended Eddy Simulation (SBES) coupled with Flamelet Generated Manifold (FGM) combustion model was selected to model …

Interaction Of Particles With Plasma And Shock Produced By Pulsed Spark Discharge, Shomik Mukhopadhyay

Dissertations

Interactions of powders with high-temperature plasma and shockwaves occur in diverse scenarios, such as nuclear blasts, accidental industrial dust explosions, solid propellant combustion in explosive charges and when removing contaminants from surfaces. Electrostatic Discharge (ESD), known for generating shock and plasma, is a promising lab-scale technique for simulating these interactions. Studies with ESD involved placing powders near a spark-producing gap between electrodes and observing mechanical and chemical processes like particle motion and ignition. A limited range of spark conditions and material properties have been tested, which facilitated the development and validation of preliminary computational models describing this system. Significant gaps …

Numerical Investigations Of Sco2 Compressor Aerothermodynamics Using A Streamline Curvature Based Throughflow Method, Victor Quintanilla

UNLV Theses, Dissertations, Professional Papers, and Capstones

Supercritical carbon dioxide (sCO₂) has emerged as a promising working fluid for the Brayton power cycle, offering enhanced efficiency due to the high density and low viscosity of carbon dioxide (CO₂) near the critical point. A critical component of the sCO₂ Brayton cycle is the turbomachinery, namely the compressor, which significantly contributes to the efficiency enhancement in the sCO₂ Brayton cycle owing to reduced compression work requirements. Its primary function involves elevating the fluid's pressure, effectively priming it for the subsequent heat addition process from a thermal energy source. However, despite its advantages, challenges …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Artificial Neural Network For Predicting Heat Transfer Rates In Supercritical Carbon Dioxide, Vinusha Dasarla Giri Babu

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide as a working fluid in a closed Brayton cycle is proving to be more efficient than a conventional steam-based Rankine engine. Understanding the heat transfer properties of supercritical fluids is important for the design of a working engine cycle. The thermophysical properties of supercritical fluids tend to vary non-linearly near the pseudo-critical region. Traditionally, empirical correlations are used to calculate the heat transfer coefficient. It has been shown in the literature and within our own studies that these correlations provide inaccurate predictions near the pseudo-critical line, where heat transfer may be deteriorated or enhanced, resulting from strong …

Understanding Unsteady Corner Separation Within Wing-Body Junction Flows, Paul G. Winner

Doctoral Dissertations and Master's Theses

Wing-body junction flows, formed at the interface between a wing and fuselage surface, are a complex, coupled, three-dimensional, turbulent flow field. This thesis focused on the unsteady corner separation that develops at the trailing edge of this wing-body junction under certain conditions. A NACA 0015 wing mounted on a flat plate at an angle of attack of 13°was used as the model junction flow field. The wing had an aspect ratio of 8 with a linear washout twist of 15°. The Reynolds number based on the wing chord was Re_c = 4.5 × 10⁵. Time-dependent stereoscopic particle …

Studies Of Multiphase Distribution And Flow In Bubble/ Slurry Bubble Columns With /Without Internals And Advanced Sustainable Construction Materials Using Sophisticated Measurement Techniques, Omar Farid

Doctoral Dissertations

"Bubble/slurry bubble columns have been widely studied and employed as multiphase flow reactors with and without vertical heat-exchanging tubes. In order to understand more deeply the effect of the dense internals on the hydrodynamics of bubble/slurry bubble column, systematic experiments were performed to visualize and quantify using the radioactive particle tracking (RPT) technique. A new methodology for implementing the radioactive particle tracking (RPT) technique has been developed to investigate the effect of the dense internals on the hydrodynamics of the bubble/slurry column reactor. Monte Carlo N-Particle (MCNP) simulation has been implemented to simulate the system to generate a large number …

Numerical Investigation On The Effect Of Spectral Radiative Heat Transfer Within An Ablative Material, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The spectral radiative heat flux could impact the material response. In order to evaluate it, a coupling scheme between KATS - MR and P1 approximation model of radiation transfer equation (RTE) is constructed and used. A Band model is developed that divides the spectral domain into small bands of unequal widths. Two verification studies are conducted: one by comparing the simulation computed by the Band model with pure conduction results and the other by comparing with similar models of RTE. The comparative results from the verification studies indicate that the Band model is computationally efficient and can be used to …

Computational Sodium Heat Pipe Simulation In Three Dimensions For Transient Nuclear Reactor Analysis With Variable Surface Heat Flux, Valerie Jean Lawdensky

UNLV Theses, Dissertations, Professional Papers, and Capstones

Heat pipes are used to transfer heat through phase change in a liquid/vapor contained in a metal tube. They are passive devices that require no pumps to circulate the fluid and can transfer heat far more efficiently than a solid copper rod of the same diameter. They are commonly used in laptop computers where copper heat pipes filled with water take heat away from the CPU and transfer the heat to air through a heat exchanger. Heat pipes were also used in the Kilopower nuclear reactor where higher temperatures required sodium as the working fluid with stainless steel tubes. Computer …

Preliminary Development Of The Dialysis-Membrane-Based Passive Biocide Delivery System For Spacecraft Water Recovery Units, Rogelio Elias Garcia Fernandez

Graduate Theses and Dissertations

The purpose of this investigation is to explore the capabilities of a dialysis-membrane-based system for the in-line dosing of silver ions to treated water in spacecraft water recovery units. The spacecraft environmental control and life support system community (ECLSS) are interested in adopting silver ions as a biocide in future spacecraft water recovery processes since silver ions are effective biocide at concentrations that humans can safely consume. The system has been designed following the configuration of the Water Processor Assembly (WPA) aboard the International Space Station. In this configuration, silver ions have to be added at the last step in …

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …

Data-Driven Tools Guided By First-Principles For Scale Modeling, Sadegh Poozesh

Progress in Scale Modeling, an International Journal

For decades, traditional scale-modeling techniques have been relying on first-principles models (FPMs). FPMs have been used to find non-dimensional numbers (PIs) and identify normalized underlying forces and energies behind the phenomenon in focus. The two main challenges with FPM-based PIs extraction are finding the relevant PIs and proper correlations between PIs. The emergence and surge of data-driven modeling (DDM) provide a new opportunity to leverage experimental data in model development across scales/plants. In this paper, first, the two mentioned issues in PIs development will be elaborated to reveal the gap, and second, a new insight into scale modeling and similarity …

The Varied Thermal Response Of Magnetic Iron-Oxide Nanoparticles During Induction Heating In Liquid And Solid-Liquid Phase Change Mediums, Joshua Tompkins

Graduate Theses and Dissertations

This study investigates the induction heating response of uncapped iron oxide nanoparticles sonically dispersed as a nanofluid and mechanically distributed in solid phase change materials. The nanoparticles examined have a mean diameter of 14.42 nm and are magnetically heated in an alternating magnetic field at an amplitude of 72.6 kA/m at frequencies of 217, 303, and 397 kHz. Nanoparticle characterization was undertaken through transition electron microscopy, x-ray diffraction, and dynamic light scattering when in suspension. Carrier fluids were characterized through viscosity, heat capacity, and density measurements which were used in the calorimetric calculation of the specific absorption rate (SAR) of …

Investigations Of Air-Water Multiphase Flow In Tubes: Computational Fluid Dynamics, Wei Hong Goo

Student Works (2020-2029)

Mixing is a very crucial process in many industries, such as food processing industry, minerals processing industry, petrochemicals and refining industry, pulp and paper industry, polymer industry, pharmaceuticals industry and many more. There are different types of mixing, such as liquid-gas mixing, liquid-liquid mixing, solid-liquid mixing and many more. The definition of multiphase flow is the simultaneous flow of materials with multiple thermodynamic phases. A lot of process industries require multiphase flows during operation. Bubbly flow is defined as the flow of liquids that contains dispersed gas bubbles. One of the main applications of multiphases flows and bubbly flows is …

Numerical And Experimental Analysis Of Air-Cooled Condensers, Kaipo Kekaula

UNLV Theses, Dissertations, Professional Papers, and Capstones

The scope of this project is to numerically and experimentally dry cooling process in air-cooled condensers (ACCs) designed for concentrated solar power (CSP) applications. This effort is driven by the growing economic and political pressure to reduce water consumption during power generation due to limited water resources in the arid geographic climate of the southwestern United States. A computational approach is used in conjunction with experimental validation to gain a more complete understanding of these systems.

Traditionally research into ACCs have been largely limited to air-side heat transfer modelling as it accounts for a large portion of the total thermal …

Thermal / Structural Analysis Of The Hb 650 Thermal Shield, Gerald J. Smith

Graduate Research Theses & Dissertations

Fermilab’s PIP-II project’s superconducting linear accelerator (Linac) will drive the next generation of particle accelerators through a revolution in beam intensity. Key to beam intensification are the high efficiencies of niobium-tin superconducting radiofrequency (SRF) cavities operating at cryogenic temperatures near 5 Kelvin. A multifaceted approach is employed to achieve and maintain the extreme temperature. Vacuum provides the first barrier to thermal convection. Physical thermal intercept zones further isolate the exterior shell vacuum vessel at 300 Kelvin from the supercooled beamline. The first thermal intercept lies just inside the exterior vacuum vessel forming the 40 Kelvin zone. This 40K thermal shield …

Performance Modeling Of Supercritical Carbon Dioxide Zigzag-Channel Printed Circuit Heat Exchangers, Katrine Birgitte Bennett

UNLV Theses, Dissertations, Professional Papers, and Capstones

Supercritical carbon dioxide (sCO2) is currently being studied as the working fluid in power producing Brayton cycles due to its excellent physical and thermodynamic properties, especially near the critical point. Printed circuit heat exchangers (PCHEs) are being considered for use as condensers and recuperators for this purpose due to their high strength and compact designs. Many experimental and numerical studies are being conducted to characterize and optimize sCO2 PCHE operation and develop correlations to describe their thermal-hydraulic performance. Additionally, a few experimental and numerical structural assessments of these PCHEs have been conducted, but all have been somewhat limited due to …

Numerical Study Of Spacer Grid Geometry In A 5 X 5 Nuclear Fuel Rod Bundle, Wan Chuan Fan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Reactor fuel rod bundles serve as the primary heat source in light water reactors (LWRs), commonly found in the aforementioned PWR plants. The fuel rod bundles’ structure consists of a collection of fuel rods put into a parallel grid configuration. The bundles also include fuel rod spacers, which hold the fuel rods in place, in accordance with the grid. Repeating structures of the fuel bundles create the meta-structure in the reactor. In other words, the grid configuration repeats until it fills the entire space of the reactor. This results in reactor fuel rods suspended in the working fluid domain, oriented …

Cfd Modeling Of Smoke Movement In An Atrium, Robin Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this paper is to better understand the behavior of smoke movement in an atrium. Thus gives first responders and civilians in and out of building a better understanding

With the advancements of modern technology, computers and softwares make simulation models possible such as fire models to simulate fire and smoke movements. In this paper, a computational fluid dynamic (CFD) software Fire Dynamic Simulator (FDS) is used to conduct a series of atrium tests to investigate the effectiveness of smoke exhaust systems. FDS solves the Navier-Stokes equations appropriate for low speed flows (Ma < 0.3) with an emphasis on smoke, heat transport and CO2 concentrations from fires. The default turbulence model used in FDS simulation is the Large Eddy Simulation (LES), which is the solution of Navier-Stokes equations at low speed.

The compartment tested was 9 …

Air Temperatures Tutorial, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Aerothermodynamic Analysis Of A Mars Sample Return Earth-Entry Vehicle, Daniel A. Boyd

Mechanical & Aerospace Engineering Theses & Dissertations

Because of the severe quarantine constraints that must be imposed on any returned extraterrestrial samples, the Mars sample return Earth-entry vehicle must remain intact through sample recovery. Vehicles returning on a Mars-Earth trajectory will attain velocities exceeding any that have been experienced by prior space exploration missions, with velocities approaching 14 km/s. Velocities as high as these will encounter significant heating during atmospheric re-entry to Earth.

The purpose of this study has been to systematically investigate the aerothermodynamic challenges that will result from a Mars sample return, Earth-entry vehicle design. The goal was to enable efficient estimation of maximum stagnation …

Intermittency Effects On The Universality Of Local Dissipation Scales In Turbulent Boundary Layer Flows With And Without Free-Stream Turbulence, Sabah Falih Habeeb Alhamdi

Theses and Dissertations--Mechanical and Aerospace Engineering

Measurements of the small-scale dissipation statistics of turbulent boundary layer flows with and without free-stream turbulence are reported for Re_τ ≈ 1000 (Re_θ ≈ 2000). The scaling of the dissipation scale distribution is examined in these two boundary conditions of external wall-bounded flow.

Results demonstrated that the local large-scale Reynolds number based on the measured longitudinal integral length-scale fails to properly normalize the dissipation scale distribution near the wall in these two free-stream conditions, due to the imperfect characterization of the upper bound of the inertial cascade by the integral length-scale. When a length-scale based on Townsend's …