Engineering Commons^™

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

Development Of Mbd Model And Analysis Methodology For Vehicle Design, Alfonso Christopher Ponce

Mechanical Engineering ETDs

This thesis is to provide a new methodology that considers the effects the chassis applies during dynamic load to the suspension and the handling characteristics of a road course vehicle. A methodology in which is described in detail as well as an applied demonstration where literature before this thesis, lacks in replication and serves to establish a basis for multi-body dynamic analysis in this area. Two models to be created, rigid and flexible, and to compare each other to study the effects the chassis torsional stiffness has during load transfer. Ultimately, to assist in the design of a vehicle that …

Fib Model Code 2020 – Durability Design And Through Life Management Of New And Existing Structures, Frank Papworth, S Matthews

International Conference on Durability of Concrete Structures

Work has recently started in fib (Fédération Internationale du Béton) on the preparation of a new fib Model Code for Concrete Structures, under the working title of Model Code 2020 (MC2020). This will be a single code dealing with both new and existing concrete structures, that is both the design of new structures and all the activities associated with the assessment, interventions and the through-life management and care of existing concrete structures. Numerous goals relating to durability and service life design have been identified, including that ideally MC2020 should incorporate:

• Better models for deterioration processes addressing issues such as …

Application Of Modern, Effective Materials In Rail Road Reinforced Bridge Elements, U.Z. Shermuxamedov, F.Z. Zokirov

Journal of Tashkent Institute of Railway Engineers

The article is about reducing the construction costs of railroad bridges and the effective use modern building materials. The article compares the technical characteristics of composite fittings and metal fittings and their proportionality. Indeed, recourse saving of metal and composite fittings, as well as factors of localization of construction is compared

Method Of Calculation Of Self-Stressed Concrete Slabs Supported Along The Contour, S.S. Salixanov

Journal of Tashkent Institute of Railway Engineers

The paper presents the developed method for calculating the contour-supported slab of self-stressed concrete. Reinforced concrete slab on the tension cement replaces the traditional construction of the bridge. In this article, in order to exclude reinforcement, the problem of determining the stress-strain state of self-stressed concrete slabs supported along the contour is considered. The values of stresses in the upper and lower faces of the concrete slab, as well as the bending moment in the middle section of the slab

Features Of Designs Of Nanosenses For The Oil Industry, A.E. Vorobev, Zhang Lianzi

Gorniy vestnik Uzbekistana

Development of design features of nanosensors for oil branch is shown. It is established that in modern nanosensors usually influence formation of a working signal as environment qualitative quantitative indices (values of temperature, pressure, speed of migration of fluids, contents of chemical elements, sizes рН, etc.) and the nature (predetermining properties), structure and extent (the geometrical sizes) of nanoparticles of sensitive elements which the studied environment influences, forming as a result this working signal. The basic design of nanosensors and the mechanism of their work is described. Distribution of nanosensors on classes depending on the principles and mechanisms of action …

Strong Circular Dichroism In Chiral Plasmonic Metasurfaces Optimized By Micro-Genetic Algorithm, Zhigang Li, Daniel Rosenmann, David A. Czaplewski, Xiaodong Yang, Jie Gao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Strong circular dichroism in absorption in the near-infrared wavelength range is realized by designing binary-pattern chiral plasmonic metasurfaces via the micro-genetic algorithm optimization method. The influence of geometric parameter modifications in the binary-pattern nanostructures on the circular dichroism performance is studied. The strong circular dichroism in absorption is attributed to the simultaneous excitation and field interference of the resonant modes with relative phase delay under linearly polarized incident light. This work provides a universal design method toward the on-demand properties of chiral metasurfaces, which paves the way for future applications in chemical and biological sensing, chiral imaging and spectroscopy.

Investigation Of The Under-Body Flow Field Of A Prototype Long-Range Electric Vehicle, Matthew P. Nguyen

Master's Theses

This thesis presents changes to the design of the Prototype Vehicles Laboratory (PROVE Lab) Endurance Car, an electric car intended to break the Guinness World Record for the single-charge range of an electric vehicle. The design range is 1609.34 km, however at the design velocity of 104.6 kph, the drag is 196 N; which requires more battery capacity than the 100 kWh maximum of the baseline model. With a fixed frontal area, drag reduction can come from lowered velocity or reduced CD. CD reduction is attempted in four ways: side skirts between the fenders, a raised ride height, an elongated …

Prototyping A Conductive Polymer Steering Pad For Rail Freight Service, Anthony A. Villarreal, Constantine Tarawneh, Miguel Ontiveros, James Aranda, Robert Jones

Mechanical Engineering Faculty Publications

The AdapterPlus™ steering pad is a polymer component on a railcar that helps to reduce stresses on the axle as a railcar rounds a curve. One railway application requires a minimum of 240 mA to be passed through the steering pad to the rail, which activates air valves that control automated cargo gates. Currently, two copper studs are inserted into the pad to provide a conductive path. However, after continuous cyclic loading caused by normal service operation, the copper studs deform, wear, and eventually lose contact between the two surfaces rendering the pad nonconductive. One proposed solution to this problem …

Cisco Nexus 9200 Robustness Redesign, Colin Berge, Ethan Gold, Cole Christopherson, Rahul Makhijani

Industrial and Manufacturing Engineering

Certain configurations of Cisco's Nexus 9200 product experienced issues with bending during shipping. Two solutions were developed to eliminate this problem: an external brace that could quickly address the problem yet was expensive and unsustainable, and a redesigned chassis, which was more economical but came with a longer time to implement. Real world packaging and shipping conditions were simulated in SolidWorks and Finite Element Analysis was used to model the stresses experienced when the product is dropped. Both designs were found to significantly reduce stress in critical areas, thus reducing the chance of failure and the cost of the problem. …

An Examination Into The Defining Characteristics Of Flexible Solar Aircraft Configurations Through Optimization, Taylor Mcdonnell, Andrew Ning

Faculty Publications

This paper examines the defining characteristics of various solar aircraft configurations through gradient-based multidisciplinary design optimization. We first present a general gradient-based solar aircraft optimization framework which accounts for nonlinear aeroelastic effects resulting from structural flexibility. We then apply this framework to several discrete SR- HALE aircraft geometric, structural, and propulsion system configuration choices to determine the defining characteristics of each configuration choice.

Journeyman International - Rubagabaga Evc And Ace - Rwanda, Africa, Jake M. Stom

Construction Management

Rubagabaga EVC and ACE, or Empowering Villages Center and Agricultural Center of Excellence, is an interdisciplinary project based senior project completed by California Polytechnic State University, San Luis Obispo students. College of Architecture and Environmental Design students Jake Stom, Mackenzie Diaz, Julia De Hart, and Jenna Williams completed the design and preconstruction services with the help of non-profit humanitarian organization, Journeyman International. The deliverable aims to serve the client, Empowering Villages, by providing the complete design of a community center and agricultural training facility near Kaseke Village in Rwanda. The goal is to provide the local community with development efforts …

High Speed Mid Altitude Aircraft Project, Eric Yan

Honors Program Theses and Projects

This project designs aircraft that addresses the space constraint that limits airport capacity by exploiting lift created by flying aircraft at high speeds (350-500KIAS) in the mid altitudes of FL100-FL200 to increase the payload of smaller aircraft. Three solutions with the length and wingspan footprint of the Boeing 737-800 are produced using the software X-Plane, then virtually flight tested for various performance data. The results find that adoption of these designs can yield significant capacity increases, albeit at reduced fuel efficiency.

Open Source Completely 3-D Printable Centrifuge, Salil S. Sule, Aliaksei Petsiuk, Joshua M. Pearce

Michigan Tech Publications, Part 1

Centrifuges are commonly required devices in medical diagnostics facilities as well as scientific laboratories. Although there are commercial and open source centrifuges, the costs of the former and the required electricity to operate the latter limit accessibility in resource-constrained settings. There is a need for low-cost, human-powered, verified, and reliable lab-scale centrifuges. This study provides the designs for a low-cost 100% 3-D printed centrifuge, which can be fabricated on any low-cost RepRap-class (self-replicating rapid prototyper) fused filament fabrication (FFF)- or fused particle fabrication (FPF)-based 3-D printer. In addition, validation procedures are provided using a web camera and free and open …

Smart Flow Facility Analysis, Chantal Ann George, Pete Suktankar, Eric Wilson, Matthew Geiger

Senior Design Project For Engineers

The SMART Flow Design Team has been tasked in providing a physical layout for a single building facility used to consolidate three separate business units. The objective for the new facility will be to manufacture, receive, ship, and store the company's finished products. When designing the physical layout, the team must take into consideration stable and seasonal business volumes, current and future volume demand growth, designated inbound, outbound, and storage areas, and product turn rates. All specifications must be met while determining an efficient flow of goods. The team has designed indoor and outdoor layouts using Microsoft Visio, performed various …

Asme Student Design Competition, Marcus Todd

Mahurin Honors College Capstone Experience/Thesis Projects

For the completion of my capstone project with the Western Kentucky University Honors College, the following document details my experience with the American Society of Mechanical Engineer (ASME) Student Design Competition. This project was completed in a two semester sequence through working with a team of four. One semester focusing primarily on the design and the other on fabrication and evaluation. The 2019 ASME competition was the Pick and Place Race. In this event, 46 teams were challenged to design and construct a device having the ability to pick up balls of varying size. Both the design and assembly process …

Civil Engineering Design Of Cornhusker Council's Outdoor Education Center, Kelly Weiler

Honors Program: Senior Projects (Public)

A team of geotechnical, structural, hydraulic, environmental, and transportation experts collaborated to provide engineering solutions to the Cornhusker Council in an effort to solve the current problems facing their Outdoor Education Center. This results of this project provided the structural design of three bridges on the property, transportation plans for two parking lots and roadway design, geotechnical recommendations for soil testing and erosion prevention, and an environmental and hydraulic analysis of the property. A major challenge in the design of this project is the consideration of the dangers and regulations that accompany the floodway and floodplain regions on site. Various …

The Pedagogy Of Design And Technology At Xavier University Of Louisiana, New Orleans, Shayna Tova Blum

Faculty and Staff Publications

Abstract. Xavier University of Louisiana (XULA) is a Science, Technology, Engineering, and Mathematics (STEM) university located in New Orleans, Louisiana. As a Historically Black University (HBCU), the university serves a diverse community of students in which many are first-generation, college graduates. Students enrolled in Design courses at XULA are studying in Bachelor of Science and Bachelor of Art programs and majoring in subjects such as Computer Science, Physics, Mass Communication, Art, Business, and Science. The interdisciplinary student environment offers a unique opportunity for collaboration and peer learning, whereby students are able to share diverse perspectives on a topic by relating …

(Poster) Combining Design And Entrepreneurial Mindset Development: Motorcycle Detection System, Pilar Echeverria, Thomas Leseure, Bailey Wilder, Oluebubechukwu Onaga, Jake Braumbaugh, Steve Spicklemire Dr., Jose Sanchez Dr., David Olawale Dr.

ASEE IL-IN Section Conference

The Motorcycle Detection System will detect and warn drivers of motorcycles driving between lanes at high speeds on the interstate. Its main function would be to significantly reduce the frequency of motorcycle-car accidents on the road. Similar to the blind spot detectors that can be found on many modern cars, the motorcycle detector would minimize the number of accidents and deaths caused by motorcycles lane-splitting. By alerting drivers of motorcycles within a 50 feet radius, motorists would be able to make calculated decisions on the road that they otherwise would not contemplate.

Through rigorous market exploration, the team deduced that …

(Poster) Combining Design And Entrepreneurial Mindset Development: Improved Multifunctional Charging Station, Allison Zwickl, Payton Staman, Evan Parduhn, Jake Smith, David Olawale, Stephen Spicklemire, Rashedul Sarker

ASEE IL-IN Section Conference

It has become imperative to find ways to organize different devices of varying functions and sizes. This problem was introduced to us through customers who believed the current designs on the market could use improvement, or through the lack of organization that they have when charging multiple devices. A solution is a modular concept with a base station that will include a wireless pad and a few charging cords. Additionally customers can purchase specialized add ons that fit into the base station. The housing station will seamlessly charge a plethora of devices including; smart-phones, smart-watches, and speakers in a centralized …

(Poster) Design And Fabrication Of A Custom Wrist Orthosis For Enhanced Patient Comfort, Marko Tasic, Matthew Hansen, Mang Lian, Demetre Mitchell, Rashedul Sarker, Renny Fernandez, Erin Peterson, Joseph Herzog, David Olawale, Najmus Saqib

ASEE IL-IN Section Conference

This custom wrist orthosis project is the continuation of efforts made by students in the R.B Annis School of Engineering during the 2017-2018 academic year. Throughout this project, we have implemented the Design for Six Sigma (DFSS) methodology to guide the design process. Within the R.B. Annis School of Engineering, this methodology has been adapted into guide the DesignSpine process. We have designed a new orthosis that is custom fabricated for enhanced patient comfort. In the occupational therapy field, patients have reportedly not been wearing their prescribed orthoses/braces, which are designed to stabilize injured areas so that they heal properly. …

Design Of Remote Control System Of Drilling Rig In Coal Mines, Weng Yinsheng, Wu Di, Lu Feifei, Wang Longpeng

Coal Geology & Exploration

In order to solve the influence of the dangerous conditions in the deep mine, such as large percus-sive ground pressure and high temperature and humidity of the roadways in deep mines on drilling operation, a remote control drilling rig control system is designed. The control system consists of local control terminal and remote control terminal, both communicating by CAN(Controller Area Network) bus and optical fiber for data and image. Local control terminal core uses automobile PLC(Programmable Logic Controller) as the control core to realize data acquisition and control, develops program in CoDeSys. The remote control terminal, based on MCU and …

Connecting Bridges Through Theatrical Design: An Examination Of “Asiri Nla” In Performance, Tochukwu J. Okeke

International Review of Humanities Studies

The theatre provides an avenue for the expression of very salient and topical issues about a people through the presentation of performances. These performances, which are often in form of plays, are always created by playwrights and that is why playwrights are said to be the watch dogs of the society because their works x-ray past and present situations while proffering solutions for the future. However, the theatre is a composite art which involves the collaboration of many creative artists: Playwright, Director, Stage Manager, Actor(s), Designer(s), amongst others. The designer(s) are the creative artists that interpret the play in visual …

A Design For Affordances Framework For Product Packaging: Food Packaging Case Study, Ahmad Abdelhafiz Mumani, Richard T. Stone, Esraa Abdelall

Journal of Applied Packaging Research

Since affordances provided by packaging features play a major role in facilitating user packaging interaction, it is important to integrate the concept of affordances into the packaging design process and to understand the interrelationships between packaging features and affordances. A framework is proposed for linking user requirements to packaging design features utilizing the concept of affordances. The framework is accomplished in two main steps; first, determine the affordances required to facilitate performing packaging-related tasks, and second, link these affordances to packaging features. Previous packaging usability studies were reviewed to elicit requirements in terms of affordance properties such as intuitiveness, responsiveness, …

Project Atlas: A Mobile Universal Rocket Engine Test Stand, Collin Mickels, Conrad H. Wright, Noah Soderquist, Alona Prokofieva, Sattar Panahandehgar, Naveen Sri Uddanti, Alcuin Rajan

Student Works

Project Atlas is a mobile, trailer-mounted, rocket engine test stand developed by Experimental Rocket Propulsion Lab (ERPL) at Embry-Riddle Aeronautical University’s Daytona Beach, Florida campus. The integrated test stand and automated data-acquisition and control system supports ERPL’s multitude of engine research projects, including bipropellant liquid and hybrid rocket engines. The need for an integrated universal mobile test stand stems from the inability to conduct frequent test fires on campus due to Class-3 airspace and liability issues. The test stand is designed as a horizontal thrust structure utilizing a dual flame duct to redirect and cancel reaction forces acting upon the …

Custom Designed Wall Mounted Shop Crane, Bradley Lewis

All Undergraduate Projects

The objective of this project was to design and fabricate a custom wall mounted jib crane to specific, non-standard dimensions. The crane was designed to be industry rated for 2000 pounds, rotate at least 180 degrees, and be designed to have a maximum boom length tailored to the specific installation site. Two potential installation sites and purposes were selected for construction: inside the bay doors of a fabrication shop, intended to transfer large pieces of material to and from a plasma table, and inside a car maintenance garage, intended to lift and remove engines and transmissions from cars.

Design of …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

A Reticulation Of Skin-Applied Strain Sensors For Motion Capture, Christopher A. Schroeck

ETD Archive

The purpose of this research is to develop a system of motion capture based on skin-applied strain sensors. These elastic sensors are of interest because they can be applied to the body without restricting motion and are well suited to operate in more practical environments, such as sports fields, gymnasiums, and outdoor areas. This combination is currently not available in the field of motion capture. The current issues with strain sensor motion capture technology is the accurate is not sufficient for motion analysis and axial rotation monitoring of joints is not available. This project will build and test a sensor …

Designing And Redesigning Products, Processes, And Systems For A Helical Economy, Ryan Bradley, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

The Circular Economy (CE) concept has promised to unlock trillions of dollars in business value while driving a significant reduction in the world’s resource consumption and anthropogenic emissions. However, CE mainly lives in ambiguity in the manufacturing domain because CE does not address the changes needed across all of the fundamental elements of manufacturing: products, processes, and systems. Conceptually, CE is grounded in the concept of closed-loop material flows that fit within ecological limits. This grounding translates into a steady state economy, a result that is not an option for the significant portion of the world living in poverty. Therefore, …

Project "Auxilia" - Jaiden's Prosthetic Arm, Christopher Halley, Lindsay Jaros, Autumn Young

Williams Honors College, Honors Research Projects

The main objective of this project was to create a prosthetic arm for a 15 year old boy named Jaiden Foden. Jaiden was born with only one fully developed limb as a result of a genetic disorder, Hanhart Syndrome II. His right arm becomes a residual limb below the elbow, but has two fingers which act in a “claw-like” movement. Jaiden’s left arm becomes a residual limb above the elbow, and his left leg becomes a residual limb above the knee. The goal of the arm was to increase Jaiden’s overall independence and to help in completing daily tasks, such …