Engineering Commons^™

The Influence Of Citric Acid On Setting Time And Temperature Behavior Of Calcium Sulfoaluminate-Belite Cement, Edgar Soriano

Civil Engineering Undergraduate Honors Theses

Today the need to opt for alternative cementitious materials is growing due to environmental reasons and construction time frames that portland cement cannot always satisfy. Calcium Sulfoaluminate (CSA) cements are a strong candidate to supplement or replace portland cement in the construction field for certain applications. In the United States, CSA cement has been limited mostly to pavement repairs because of its rapid initial setting time. The chemical compound responsible for this phenomenon is the alumina. This compound and sulfate are present in larger proportions compared to portland cement. The purpose of this research is to study how the use …

Using Of Proper Pavement Material For The Intersections With Slow-Moving Traffic, Bekim Selimi

International Journal of Business and Technology

Use of proper pavement material for some of intersections need special attention by road designers. At Camp Bondsteel-Kosovo on 2002 were built four road intersections using the concrete as pavement material. Heavy and slow-moving trucks that are turning or accelerating exposed these intersections to some of the highest stress level. After some years this intresections start deteriorating on their surface due to friction. The concrete pavements did not survive this period of usage and after eight years were removed and replaced with asphalt pavements. After more than seven years, the asphalt has shown minor distress but is still in good …

Reducing The Porosity And Sealing Cracks By Using Crystalline Admixture In Conventional Concrete, Visar Krelani, Liberato Ferrara

International Journal of Business and Technology

There is a continuous increase of quality on civil engineering materials in developed countries and parallel increase of need for new constructions in developing countries. Professional community should propose solutions for the durability that can resist in different severe environments. The most important factor that can affect concrete durability is represented by the pore distribution. Transport properties can take place through the porous network inside the cementitious composites and the aggregates interface, permitting the ingress of aggressive agents damaging concrete function intrinsically as a material and the wellfunctioning of the entire structure. The use of a crystalline admixture during the …

Prediction Of Punching Shear Capacity Of Two-Ways Frp Reinforced Concrete Slabs, Ilker Fatih Kara, Besian Sinani

International Journal of Business and Technology

An innovative solution to the corrosion problem is the use of fiber-reinforced polymer (FRP) as an alternative reinforcing material in concrete structures. In addition to the non corrodible nature of FRP materials, they also have a high strength-to-weight ratio that makes them attractive as reinforcement for concrete structures. Extensive research programs have been carried out to investigate the flexural behavior of concrete members reinforced with FRP reinforcement. On the other hand, the shear behavior of concrete members, especially punching shear of two-way slabs, reinforced with FRP bars has not yet been fully explored. The existing provisions for punching of slabs …

Evaluation Of Nebraska’S Aggregate Reactivity By The Miniature Concrete Prism Test Method – Aashto T380, Lieska Halsey, Wally Heyen

Nebraska Department of Transportation: Research Reports

The evaluation of nine different aggregates shows the viability of the T380 test method as an alternative to the standard C1293 test method. The T380 assesses the Alkali-Silica Reaction potential of aggregates with the same reliability as C1293 and correlates well with the C1293 test method. Results are obtained within 56 days by T380 compared to 365 days required by C1293. The T380 method at 56 days appears to characterize the aggregate reactivity similarly to C1293 for all the aggregates evaluated in this study. Therefore, T380 will be part of the Department test method for approval of interground/blended cements along …

Effect Of Moisture Condition On Concrete Core Strengths, Wally Heyen, Lieska Halsey

Nebraska Department of Transportation: Research Reports

The main purpose of this study was to determine if there would be any major differences between curing methods of cores taken for acceptance testing from a highway slab on a project. The comparison provided data to determine the effect of the moisture gradients created by these different curing treatments on core strength and core permeability. The strengths were measured of moist cured cores and sealed plastic bag cured cores from the day cores were obtained (14, 21 and 26 days) until they reached 28 days. Permeability was also measured at 26, 28 and 32 days. According to ASTM C42, …

Investigating The Interaction Of Ndot Hot-Pour Pcc Joint Sealant And Penetrating Concrete Sealers, Bruce Barrett, Dale Byre, Wally Heyen, Lieska Halsey, David Hansen

Nebraska Department of Transportation: Research Reports

Based on the field observations on NE-83, PCS potentially impacts the bond between the concrete and hot-pour sealant after application. If penetrating sealers break the interfacial bond after application, concrete pavements could become compromised and subject to freeze-thaw damage, chloride attack, and other deleterious effects.

The results show that discoloration occurred when applying the five PCS products to the NE-3405 hot-pour sealed testing blocks. All three test methods of application; spraying, 1-min, and 5-min soaks, caused discoloration. The level of discoloration increased with the duration of contact with the PCS. Despite discoloration, none of the five PCS products caused de-bonding …

Development Of Test Methods For Characterizing Extrudability Of Cement-Based Materials For Use In 3d Printing, Jonathan Thomas Kuchem

Masters Theses

"3D printing is the process of creating three-dimensional objects using an automated additive manufacturing process. The 3D printing process has been used with materials such as metals and polymers, but application with cement based materials for the construction industry has yet to be developed. In this research, two main problems were investigated for printing cement based composite materials: extrudability and tensile reinforcement. Fiber-reinforced concrete (FRC) was studied as an internal reinforcing system to increase tensile/flexural strength. First, FRC was studied to investigate mechanical properties and use of fibers from waste tires as an environmentally friendly option. A reference mixture with …

Projectile Impact Effects On A 50 Psi Plug Type Coal Mine Seal, Bruce Albert Von Niederhäusern

Masters Theses

"The current lack of projectile damage criteria for mine seals is assessed to determine if criteria should be developed. Impact experiments were performed on a full-scale 50 psi mine seal to determine failure modes, dynamic stress state, and assess risk to existing operational mine seals. Test projectiles were selected from common underground coal mine items propelled by means of a black powder projectile generator. Projectile velocities attained in testing ranged from approximately 100 to 650 ft/s (30 to 200 m/s). Dynamic strain was measured on the non-impact face to derive the state of stress and estimate failure criteria. Penetration models …

Incorporation Of Contaminated Sediment Into Environmentally Safe Concrete, Andrew Needs

Williams Honors College, Honors Research Projects

The research performed through this project provided some interesting results on how the different properties of the contaminated sediment can impact the strength of the new concrete.

Average three, seven, and fourteen-day strengths increased when comparing to the baseline mix developed for the experiment. Increases in strengths were notices in the ten and twenty-five percent soil replacement mixes. The largest increase was approximately thirty-three percent greater than the baseline average.

The results from the forty percent replacement test showed a significant decrease in strengths when comparing against the baseline mix. A loss of about thirty percent was observed between the …

Analysis Of Standardized Concrete Mixes, Riley Graybeal

Williams Honors College, Honors Research Projects

Concrete is one of the most common materials used in construction. It is mass produced throughout the country, with numerous different designs for concrete mixes. A common practice among concrete manufacturers is to use a standardized concrete mix design. These standardized mix designs are pre-tested and are not usually altered frequently. The hypothesis of this research project is that manufacturers do not constantly investigate new ways to save on their mixes, and simply use the same standardized mix designs.

In this research, investigations into what alterations may reduce the cost of standardized mixes began with a baseline mix design provided …

Design And Performance Of Fiber-Reinforced Concrete With Adapted Rheology For Construction And Repair Of Bridge Structures, Ahmed Abdelrazik

Doctoral Dissertations

“The objective of this document is to design high-performance fiber-reinforced self-consolidating concrete (FR-SCC) for infrastructure repair and fiber-reinforced super-workable concrete (FR-SWC) for bridge construction. The investigated fibers included propylene synthetic fibers, hooked steel fibers, double and triple hooked steel fibers, hybrid crimped steel fiber and polypropylene multifilament fibers, and micro-macro steel fibers. The fiber volume varied between 0 and 0.75%. An expansive agent (EA) was incorporated to compensate for shrinkage and induce compression in the concrete at early age. Two types of EA (G and K) were employed at 0 to 8%, by mass of binder. The investigated FRSCC and …

On The Development Of 8,000 Psi Geopolymer Mortar For Practical Use In Field Applications, Remington Gabriel Reed

Graduate Theses and Dissertations

Although there are several perceived benefits from the use of geopolymer binder as an alternative to ordinary portland cement in concrete materials, it is not widely used in field applications. Geopolymer materials have no set guidelines for mixture design and often require heat curing to facilitate strength gain. Additionally, many geopolymers are created using carefully controlled and high quality materials and activator chemicals. These factors greatly affect the practicality of the material. The goal of this research was to create a geopolymer material capable of achieving high compressive strengths at 28 days without heat curing, and using only readily available …

Effect Of Cement Content On Concrete Performance, Caleb Joshua Lebow

Graduate Theses and Dissertations

Of all the traditional concrete materials, portland cement has the greatest impact on mixture cost and the environment. Cement is in many ways the glue holding concrete together (Weiss, 1999), and as such, it plays a major role in fresh and hardened concrete properties. Without the proper range of cement in the mixture, low strength development or excessive shrinkage may occur leading to premature deterioration. The Arkansas Department of Transportation (ARDOT) recognizes two types of concrete for use in bridge construction, Class S and Class S(AE). This paper focuses on the findings from testing of Class S(AE) concrete, short for …

Detection Of Multiple Flaws In Concrete Bridge Decks Using Ultrasonic Wave Propagation, Ece Erdogmus, Eric Garcia, Michael Schuller, Donald Harvey, Kelsey Stithem, Monica Houck

Nebraska Department of Transportation: Research Reports

No abstract provided.

Self-Healing Microcapsules As Concrete Aggregates For Corrosion Inhibition In Reinforced Concrete, Homero Castaneda, Marwa Hassan, Miladin Radovic, Jose Milla

Data

Corresponding data set for Tran-SET Project No. 17CLSU08. Abstract of the final report is stated below for reference:

"Reinforced Concrete (RC) structures are vital to the US’s civil infrastructure for their strength and versatility. Unfortunately, RC elements deteriorate rapidly when exposed to corrosive environments. One possible solution is to extend the life of RC elements and systems using microencapsulated corrosion inhibitors to reduce the rebar corrosion rate. The capsules house an anodic corrosion inhibitor agent including calcium nitrate (CN) and triethanolamine (TEA). The integration of such microencapsulated materials will enhance the durability and extend the useful life by controlling the …

Bridge Deck Overlays Using Ultra-High Performance Concrete, Craig Newtson, Brad Weldon

Data

Corresponding data set for Tran-SET Project No. 17CNMS01. Abstract of the final report is stated below for reference:

"This study investigated the use of a locally produced ultra-high performance concrete (UHPC) as an alternative to typical overlay materials. Several bond strength tests including slant-shear, splitting tension, and direct tension tests were performed to assess the bond strength between UHPC and normal strength concrete (NSC) substrate with varying surface textures. Tests were also conducted to assess the early-age and longer-term shrinkage behavior and coefficient of thermal expansion of the UHPC as well as rapid chloride permeability testing. Good bond between UHPC …

Use Of Rice Hull Ash (Rha) As A Sustainable Source Of Construction Material, Zahid Hossain, Ashraf Elsayed

Data

Corresponding data set for Tran-SET Project No. 17CASU02. Abstract of the final report is stated below for reference:

"With the imminent shortage of natural resources, the need to find sustainable development is the highest in recent history. Therefore, this study examines the potential uses of Rice Hull Ash (RHA) as a sustainable cementitious material (SCM) in preparation of concrete. This study also assesses the use of RHA as an alternative of commonly used polymers in preparing high-grade asphalt binders. RHA is a potential sustainable solution because it is currently being treated as an agricultural waste material, yet its high silica …

Evaluation Of The Performance And Cost-Effectiveness Of Engineered Cementitious Composites (Ecc) Produced From Region 6 Local Materials, Gabriel Andres Arce Amador, Tyson Rupnow, Marwa Hassan

Data

Corresponding data set for Tran-SET Project No. 17CLSU05. Abstract of the final report is stated below for reference:

"The project objective is to develop cost-effective Engineered Cementitious Composites (ECC) with locally available ingredients in Region 6 to address the deficiencies observed in ordinary concrete materials. The study explored the utilization of two types of river sands (coarse and fine), two types of PVA fibers (long and short), four levels of cement replacement with Class F fly ash, and the implementation of recycled crumb rubber in the performance of ECC materials. A total of 24 mix designs were prepared and evaluated …

Building A Handicap Accessible Entrance And Gabion Wall, David C. Marter

Construction Management

As people age, their bodies naturally deteriorate and often times people are confined to wheelchairs in order to get around. Uneven and unstable ground is a large obstacle for people who live confined to a wheelchair. This project was derived and designed in order to help a family with multiple family members bound to wheelchairs to allow them an easier point of access into the home. The project itself consists of the construction of a concrete walkway and a gabion wall to provide some additional aesthetics. The concrete pathway ranges from the driveway to a paver pathway that curves around …

Epoxy Interlocking: A Novel Approach To Enhance Frp-To-Concrete Bond Behavior, Cheng Jiang, Baolin Wan, Yu-Fei Wu, John Omboko

Civil and Environmental Engineering Faculty Research and Publications

This paper presents a novel approach which can enhance the interfacial bond behavior between fiber reinforced polymer (FRP) composite material and concrete. Epoxy ribs are formed by grooving on the concrete surface before epoxy is applied. The dowel action from the epoxy ribs leads to an “epoxy interlocking” effect. The mechanism of the proposed epoxy interlocking approach was analyzed in this paper from both adhesion and interlocking aspects. Furthermore, the partial interaction of the epoxy interlocking was quantified and calibrated by experimental results. The epoxy interlocking in the tested specimens led to an 88.8% increase in bond strength on average. …

Self-Healing Microcapsules As Concrete Aggregates For Corrosion Inhibition In Reinforced Concrete, Homero Castaneda, Marwa Hassan, Miladin Radovic, Jose Milla

Publications

Reinforced Concrete (RC) structures are vital to the US’s civil infrastructure for their strength and versatility. Unfortunately, RC elements deteriorate rapidly when exposed to corrosive environments. One possible solution is to extend the life of RC elements and systems using microencapsulated corrosion inhibitors to reduce the rebar corrosion rate. The capsules house an anodic corrosion inhibitor agent including calcium nitrate (CN) and triethanolamine (TEA). The integration of such microencapsulated materials will enhance the durability and extend the useful life by controlling the corrosion precursors and the corrosion process during damage evolution. Therefore, this work aims to develop and characterize the …

Fungi: A Neglected Candidate For The Application Of Self-Healing Concrete, Congrui Jin, Rui Yu, Zhonghe Shui

Department of Civil and Environmental Engineering: Faculty Publications

Self-healing mechanism in concrete has been so far achieved mainly by three approaches: autogenous healing, encapsulation of polymeric material, and biologically induced mineralization of calcium carbonate. The microbial approach prevails over the other two approaches due to the high compatibility between the filler material and the concrete compositions. Although the term “microbe” refers to many different types of organisms, research work on self-healing concrete has been so far restricted to bacteria. In this perspective article, we review the current status of bacteria-mediated self-healing concrete and summarize the prospects for future advances. In particular, we point out that fungi may have …

Comparison Of Deep Convolutional Neural Networks And Edge Detectors For Image-Based Crack Detection In Concrete, Sattar Dorafshan, Robert J. Thomas, Marc Maguire

Civil Engineering Faculty Publications

This paper compares the performance of common edge detectors and deep convolutional neural networks (DCNN) for image-based crack detection in concrete structures. A dataset of 19 high definition images (3420 sub-images, 319 with cracks and 3101 without) of concrete is analyzed using six common edge detection schemes (Roberts, Prewitt, Sobel, Laplacian of Gaussian, Butterworth, and Gaussian) and using the AlexNet DCNN architecture in fully trained, transfer learning, and classifier modes. The relative performance of each crack detection method is compared here for the first time on a single dataset. Edge detection methods accurately detected 53–79% of cracked pixels, but they …

Evaluation Of The Performance And Cost-Effectiveness Of Engineered Cementitious Composites (Ecc) Produced From Region 6 Local Materials, Gabriel Andres Arce Amador, Tyson Rupnow, Marwa Hassan

Publications

The project objective is to develop cost-effective Engineered Cementitious Composites (ECC) with locally available ingredients in Region 6 to address the deficiencies observed in ordinary concrete materials. The study explored the utilization of two types of river sands (coarse and fine), two types of PVA fibers (long and short), four levels of cement replacement with Class F fly ash, and the implementation of recycled crumb rubber in the performance of ECC materials. A total of 24 mix designs were prepared and evaluated in compression, tension, and bending to assess its mechanical properties. Furthermore, the cracking characteristics of the materials produced …

Bridge Deck Overlays Using Ultra-High Performance Concrete, Craig Newtson, Brad Weldon

Publications

This study investigated the use of a locally produced ultra-high performance concrete (UHPC) as an alternative to typical overlay materials. Several bond strength tests including slant-shear, splitting tension, and direct tension tests were performed to assess the bond strength between UHPC and normal strength concrete (NSC) substrate with varying surface textures. Tests were also conducted to assess the early-age and longer-term shrinkage behavior and coefficient of thermal expansion of the UHPC as well as rapid chloride permeability testing. Good bond between UHPC and NSC substrate was observed even with inadequate surface texture. Combined shrinkage and thermal effects were investigated for …

Coir Fiber Reinforced Concrete, Jose De La Serna, Moses Karakouzian

AANAPISI Poster Presentations

This poster exhibits the testing and research done on general Portland Cement Concrete with the addition of coir (coconut) fibers as reinforcement. Using the fundamental constituents of cement (water, cement, fine and coarse aggregate) and processed coir fiber, concrete specimens were batched to test for compressive and flexural strengths (per appropriate ASTM standards). Cylindrical and rectangular beam specimens were subjected to loadings until failure occurred. The capacity and modes of failures of the specimens were observed. It was determined that:

• The addition of processed coir fibers decreases the overall strength of general Portland Cement Concrete. • The tested concrete’s …

Waterproofing Options For Bridge Decks, Danny Wells, Sudhir Palle, Theodore Hopwood Ii

Kentucky Transportation Center Research Report

Due to the increasing use of deicing chemicals and the subsequent intrusion of chlorides into bridge decks, it is necessary to expand the use of available protective measures, including waterproofing materials. Waterproofing options that fall into three categories; 1) membranes (liquid and sheet systems), 2) friction polymers (laminates), and 3) polymer asphalts. This study assessed the waterproofing characteristics of these products. Prior to this study, no common test had been established to compare the performance of waterproofing products. A test method was developed that closely follows ASTM D5084, “Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials …

Modeling And Simulation Of Damage In The Brazilian Indirect Tension Test Using The Finite-Discrete Element Method, Jeremiah C. Leyba

Civil Engineering ETDs

The Brazilian indirect tension test is used to investigate possible correlations between progressive damage and associated permeability changes. The test offers ease of replicability with a damage behavior known to lead to fracture openings as a tool for interpreting the indirect tensile strength of concrete and rocks. This behavior can lend insight into the nature of tensile damage and fracture progression in association with changes in permeability. The nature of these brittle materials is known to exhibit rapid failures in the Brazilian indirect tension test and require a method to retard the progression of damage for the possibility of acquiring …

Comparison Of Deep Convolutional Neural Networks And Edge Detectors For Image-Based Crack Detection In Concrete, Sattar Dorafshan, Robert J. Thomas, Marc Maguire

Civil and Environmental Engineering Faculty Publications

This paper compares the performance of common edge detectors and deep convolutional neural networks (DCNN) for image-based crack detection in concrete structures. A dataset of 19 high definition images (3420 sub-images, 319 with cracks and 3101 without) of concrete is analyzed using six common edge detection schemes (Roberts, Prewitt, Sobel, Laplacian of Gaussian, Butterworth, and Gaussian) and using the AlexNet DCNN architecture in fully trained, transfer learning, and classifier modes. The relative performance of each crack detection method is compared here for the first time on a single dataset. Edge detection methods accurately detected 53–79% of cracked pixels, but they …