Engineering Commons^™

Considerations For Developing Dna-Templated Dye-Aggregate Systems, Simon Kristopher Roy

Boise State University Theses and Dissertations

Molecular excitons have been the subject of significant research interest for nearly 100 years. Molecular excitons arise when conjugated organic molecules (dyes) are excited such that the resulting excitation is delocalized over multiple dyes in a wavelike manner. The shared excited states that allow the excitation energy to hop between molecules is of particular interest for applications that can make use of the wavelike properties of excitons, including applications in quantum information science. A key challenge for developing materials for these advanced applications is to overcome the knowledge gaps associated with precisely templating dyes with spatial control of their aggregation, …

A Numerical Investigation Of Erection Bridging In Double-Pitched Open-Web Steel Joists, Logan Joshua Ward

All Graduate Theses and Dissertations, Fall 2023 to Present

Open-web steel joists are truss members used to support roofs and floors in steel buildings. They are commonly used because they are lightweight and inexpensive to manufacture on a large scale but have a large load carrying capacity due to their depth. Because of this depth, these joists are very unstable laterally, which is addressed by adding bridging (horizontal or diagonal) members between them to resist rotation of the joists. One of the bridging types is erection bridging, which is used to prevent a joist from buckling laterally while steel erectors are traversing it during construction.

The current erection bridging …

Evaluating The Impact Of Maximum Aero-Thermal Heating On A High-Speed Fixed-Wing Atmospheric Aircraft Optimum Trajectory, Benjamin M. Ford

All Graduate Theses and Dissertations, Fall 2023 to Present

This study explores how extreme heating affects the flight paths of hypersonic aircraft—vehicles that travel at speeds many times faster than sound. Analyzing how to fly a high-speed aircraft without overheating it can prevent structural failure while operating at maximum possible performance. The results shown in this section indicate that it is possible to operate at very high speeds in an aircraft while keeping peak vehicle temperature below our limits while saving fuel.

Development Of A High-Performance, Cost-Effective Architecture For Real-Time Fourier Transform Analysis On An Efinix Trion Fpga, Luke Cashwell

Honors Theses

This project presents the development of a high-performance, cost-effective, and powerefficient pipelined architecture designed to execute 10,000 Fast Fourier Transforms (FFTs) per second on an Efinix Trion T120 FPGA. Each FFT processes 4096 signed 13-bit elements, facilitating real-time data analysis for a Time-Domain Impedance Probe (TDIP) operating at a maximum data rate of 490 Mbit/s. The algorithm utilizes the built-in multipliers and dual-port memory cells of the FPGA to optimize data storage, transfer, and processing. It achieves this high performance while only using approximately 4% of the Look-Up Tables (LUTs), 7% of the integrated RAM cells, and 15% of the …

Enhanced Point Cloud Generation From A Novel 360° Underwater Lidar, Olagoke E. Daramola

Dissertations

This dissertation presents novel algorithms to improve the mapping capabilities of a 360-degree underwater Pulsed Laser Line Scanner LiDAR (PLLS-360°). Due to its 360° field-of-view (FOV), the PLLS-360° is a compact full-waveform omnidirectional imager suitable for seafloor mapping, underwater asset inspection, object detection, ice-sheet mapping, and construction progress monitoring. The proposed methodology includes an improved waveform fitting technique for saturated waveform recovery, detection array response correction, radiometric corrections, and fusion of LiDAR and sonar bathymetric datasets. The first part of this dissertation assesses the LiDAR’s performance and describes how the data for this unique 360° FOV architecture is processed. The …

Data-Driven Stochastic Programming For Disaster Housing Logistics Planning, Sheng-Yin Chen

All Dissertations

This dissertation develops an integrated modeling and solution framework for direct temporary disaster housing logistics under demand uncertainty. The proposed framework addresses the problem from short-term, long-term, and computational perspectives. First, a two-stage chance-constrained stochastic programming (TSCC) model is developed for short-term housing logistic planning, with demand scenarios generated via a data-driven spatial regression model that captures the relationship between housing demand, hazard exposure, and socioeconomic factors. A case study based on Hurricane Ian demonstrates that the TSCC model outperforms deterministic and traditional scenario-based models in both solution quality and robustness. Second, to address long-term housing logistics planning, a multi-horizon …

Crevice Corrosion Mechanisms Of Cocrmo Alloys In Orthopedic Implants: Retrieval Analysis, Nano-Tribocorrosion And Cellular Responses, Hwaran Lee

All Dissertations

Mechanically assisted corrosion and non-mechanically (chemically) driven corrosion in modular junctions of orthopedic implants using cobalt-chromium-molybdenum (CoCrMo) alloys remain clinical concerns and may contribute to implant failure. The underlying corrosion mechanisms are not yet fully understood, leaving a critical research gap. We hypothesized that corrosion in modular junctions may be driven by aggressive local environments, including fretting, metal ion release (cobalt ion, Co²⁺), low pH and reactive oxygen species (ROS). This dissertation aims to (1) analyze corrosion modes and potential causes in modular junctions; (2) identify chemically driven corrosion modes on CoCrMo alloys using simulated inflammatory modular taper …

Self-Poled P(Vdf-Trfe) Based Composites For Energy Harvesting And Wearable Sensor Applications, Lavanya Muthusamy

All Dissertations

The growing demand for flexible, low-power, and self-powered wearable electronic systems has accelerated research interest in polymer-based sensors and energy harvesting technologies. Among piezoelectric polymer materials, Poly(vinylidene fluoride-trifluoro ethylene) [P(VDF-TrFE)], over the years, has garnered significant attention due to its unique piezoelectric properties, high dielectric constant, mechanical flexibility, thermal stability, chemical resistance, biocompatibility and compatibility with scalable fabrication processes. Despite its advantages, conventional P(VDF-TrFE)-based devices often require external poling and face limitations in integration with low-cost, flexible substrates. To overcome these limitations, this research study explores the nanofiller approach, along with facile fabrication processes, and structural design strategies aimed at …

How Developers Use Type-System Related Programming Language Features, Samuel W. Flint

School of Computing: Dissertations, Theses, and Student Research

Optional type annotations are a popular feature of programming languages that allow developers to omit explicit type information in code while, in some cases, retaining many of the benefits of static typing, such as in-code documentation, improved detection of type errors, or enforcement of code properties. However, how developers use and understand optional type annotations is not clear. The focus of this dissertation is to understand the use and comprehension of optional type annotations.

Optional type annotations are examined through four lenses: first, by examining the evolution of usage in a statically typed programming language (Kotlin, the default language for …

Mechanoregulation Of Osteogenesis And Adipogenesis Of Human Mesenchymal Stem Cells, Justin Caron

Master's Theses

Bone-related diseases (e.g., osteoporosis) are primarily treated with pharmacologic therapies that often exhibit limited efficacy and substantial side effects. Currently, bone marrow derived mesenchymal stem cells (MSCs) have become one of most important cell options in bone regeneration due to readily available sources, strong proliferation abilities, weak immune rejection responses, and strong osteogenic differentiation potential. While identifying the most effective approach to enhance osteogenic differentiation of MSCs for bone regeneration is challenging, understanding the regulatory mechanisms is crucial for improving therapeutic efficacy. Recent research has focused on developing strategies to enhance osteogenesis, which involve biophysical and biochemical stimulation. Mechanical and …

Simulation- And Machine Learning-Based Methods For Inland Waterway Operation And Maintenance Decision-Making, Maryam Aghamohammadghasem

Graduate Theses and Dissertations

The U.S. inland waterway transportation system (IWTS) is an essential part of the country's multimodal freight transportation network. In addition to seasonal droughts and floods, the operations of the IWTS may be disrupted by random malfunctions and scheduled maintenance of its critical components. Among these critical components, locks play a key role in the operation of navigable inland waterways, and lock-induced disruptions to the supply chains of related industries, such as agriculture and manufacturing, often result in significant economic losses. To assess the performance of the U.S. IWTS, we develop a PyNetLogo simulation tool to capture the movements and delays …

Trauma Network Design Considering Patient Safety And Cost., Lin Lin

Electronic Theses and Dissertations

Trauma, as the leading cause of mortality and morbidity for those under the age of 45 in the US, incurs trillions in annual economic costs. The time-sensitive nature of trauma treatment necessitates an effective, coordinated regional trauma system to optimize patient safety. However, the financial burden associated with trauma care, especially due to low-insured population, presents a significant challenge to the financial health of trauma centers (TCs). To address critical challenges in this domain and provide much-needed insights to trauma decision-makers regarding their trauma system cost, network design, and subsidy policy, this dissertation proposes 3 contributions. First, we introduce an …

Anisotropic Object-Based Shifts Of Attention Arise From Unequal Influences Of Visual Field Meridians On Neural Attention Gradients, David H. Hughes, Adam J. Barnas, Adam S. Greenberg

Biomedical Engineering Faculty Research and Publications

Object-based attention prioritizes the processing of information appearing within a selected object. We previously showed an object-based shift direction anisotropy (SDA) whereby horizontal shifts are more efficient than vertical shifts (Barnas AJ, Greenberg AS. Atten Percept Psychophys 78: 1985–1997, 2016; Barnas AJ, Greenberg AS. Vis Cogn 27: 768–791, 2019), an effect modulated by the visual field meridians (Barnas AJ, Greenberg AS. Q J Exp Psychol (Hove) 77: 2516–2532, 2024). Our present aim was to understand how the functional brain mechanisms of attention give rise to the SDA. We hypothesized that the SDA arises from attentional resources being partitioned differently by …

Ferroelectricity And Multiferroicity In Ultrathin Films Of Unconventional Transition Metal Oxide, Xin Li

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

Ferroic orders of transition metal oxides, such as ferroelectricity and ferromagnetism, are determined by the intercoupling between spin, charge, lattice. Consequently, ferroic epitaxial thin films have attracted wide interest due to the profuse novel phenomena and the great application potentials for modern electronics. However, the mainstream of the study for transition metal oxides has focused on perovskite structure, limiting the understanding and discovery of novel phenomena associate with ferroic orders. In this thesis, the epitaxial films of hexagonal rare-earth ferrites (h-RFeO₃) and fluorite-structure hafnia oxide (HfO₂) are studied comprehensively, providing new experimental and theoretic …

Data-Driven Koopman Theory For Transient Stability And Safety Analysis Of Power Systems With Renewable Penetration, Bhagyashree Umathe

All Dissertations

This dissertation presents a novel approach to analyzing and controlling nonlinear systems using the Koopman operator framework and data-driven methods. Nonlinear power systems, characterized by complex behaviors and sensitivity to initial conditions, pose significant challenges for stability and safety assessment, especially during transient events.

The first part of this work focuses on reachability analysis using the spectral properties of the Koopman operator. By leveraging eigenfunctions extracted from sampled trajectory data, the approach computes forward and backward reachable sets efficiently, even in high-dimensional nonlinear systems, without requiring dense state-space sampling. This method is validated through numerical examples, demonstrating its ability to …

Enhancing Microgrid Protection Through Adaptive Decentralized Relay Coordination: A Solution To Blinding And Sympathetic Tripping, Sujatha Balasubramanian, J. Preetha Roselyn, Prabha Sundaravadivel

Electrical Engineering Faculty Publications and Presentations

Integrating Distributed Energy Resources into microgrids modifies the network’s system parameters and causes it to exhibit behaviour, particularly during fault conditions. This is due to the greater variations in current direction and magnitude. When a microgrid runs in autonomous mode, Distributed Generators result in a reduced short circuit current compared to a system working in grid-connected mode. Microgrid protection issues, namely, blinding of protection, sympathetic tripping, and bidirectional power flow, occur in the power network under such circumstances. The impact of microgrid protection issues and changes in fault current leads to variations of overcurrent relay settings, their operating time and …

Low-Level Memory Attacks On Edge Assisted Robotic Applications, William Arnold

Master of Engineering Theses

This thesis investigates how low-level memory faults can undermine edge-assisted robotic systems that rely on memory optimization. As robots are utilized in real world applications, the ability to operate safely and successfully in mission critical deployment becomes important. To help achieve these goals, developers are increasingly starting to place computation nodes at network edges to meet latency and reliability requirements. Edge nodes, however, are resource-constrained and resources conservation techniques such as Kernel Same-page Merging (KSM) are enabled to deduplicate identical pages across processes or virtual machines. This thesis shows that this optimization technique quietly widens the attack surface and can …

Towards Improving Computational Modeling Of The Lumbar Spine - Impact Of Material Properties And Laminotomy On Spinal Biomechanics, Isaac K. Kumi

Mechanical & Aerospace Engineering Theses & Dissertations

Spinal ligaments play a crucial role in maintaining the mechanical stability of the lumbar spine. These dense, collagenous tissues not only resist excessive motion but also distribute loads between spinal components to protect neural structures. Traditionally, the mechanical response of ligaments has been modeled using linear elastic assumptions, which treat the tissue as having a constant stiffness regardless of loading history. While this simplifies analysis, it fails to capture the time-dependent behaviors, such as creep, stress relaxation, and hysteresis, that are characteristic of biological tissues.

Viscoelastic modeling may provide a more physiologically accurate representation by incorporating both elastic and viscous …

Analysis On Plasma Propulsion Thruster Material Reconfiguration For Thrust Stabilization, Chinedumu Chidiebere Okafo

Mechanical & Aerospace Engineering Theses & Dissertations

Rocket propulsion has been a primary focus for scientific and technical advancement supporting space exploration. For long-duration, low-thrust space missions, propulsion systems designed with plasma energy as the primary source for generating thrust are of high interest. Plasma energy, like electric propulsion, involves the excited state of ionized atoms, where the ionized particles are separated and then act as a propellant to push a spacecraft in the intended direction for flight. Although more energy efficient compared to traditional rocket systems, plasma propulsion has the deficiency of consistent erosion of the metallic containment substrate, as plasma is being generated and released …

Human Activity Recognition And Identification Driven Automated Deep Learning For Time-Series Classification, Justin Alan Gamble

Engineering Management & Systems Engineering Theses & Dissertations

The growing emphasis on Digital Engineering (DE) within the U.S. Department of Defense (DoD) demands advanced methods for leveraging vast time-series data generated by sensor-rich environments. Deep learning models offer promising solutions for complex timeseries classification tasks, however their design and optimization remain highly resource intensive, requiring specialized expertise. This dissertation addresses this challenge by developing and evaluating an Automated Machine Learning (AutoML) framework specifically tailored for the time-series classification task of Human Activity Recognition and Identification (HARI).

A systematic investigation was conducted using the Design Science Research Methodology (DSRM) comparing traditional search strategies of grid search and random search …

Input Structure Based Optimization For Privacy Preserving Ai Systems, Feng Yizhou

Electrical & Computer Engineering Theses & Dissertations

As Artificial Intelligence (AI) systems become increasingly integrated into critical domains, ensuring privacy-preserving model design and system deployment has become a pressing priority. Safeguarding both sensitive user data and proprietary model parameters is critical throughout the AI model and system, from data acquisition and pre-processing to model inference and deployment. However, existing privacy-preserving frameworks face several limitations, including fragmented data ownership, incomplete protection across system stages, substantial computational overhead, and poor scalability to modern architectures such as large language models. This dissertation explores a unifying optimization strategy centered on input structure design to address these challenges. The core idea is …

Mxenes At The Forefront: Advances In Energy Storage And Nanofluidic Applications, Zafar Said, Maham Aslam Sohail, Hassina Tabassum, Imran Haider Sajid, Hafiz Muhammad Ali, Furqan Jamil, Yogendra Kumar Mishra, A. K. Pandey

Research outputs 2022 to 2026

This review summarizes recent studies on MXenes and their composites regarding energy storage and nanofluidic devices. MXenes are a new family of two-dimensional transition metal carbides and nitrides that have gained much attention in recent times due to their excellent physicochemical properties, such as its exceptionally high electrical conductivity, even more than that of metals, thermal stability, hydrophilicity, high energy and power densities, tunable structures, and large surface area along with abundant electrocatalytically active sites. These features, along with larger interlayer gaps compared with graphene, point to the emergence of MXenes as energy storage alternatives. Synthesis, properties, and applications of …

Valorizing Cement Kiln Dust And Glass Powder: A Binder Study On Sustainable Partial Cement Replacement, Sai Kiran Simhadri

Civil & Environmental Engineering Theses & Dissertations

The production of cement ranks as a major source of global CO₂ emissions because of the high energy requirements needed to create clinker. The construction industry is actively seeking ways to reduce its carbon footprint. Utilizing industrial waste materials to partially replace cement can lower emissions. This research evaluates a ternary binder system which uses Cement Kiln Dust (CKD) and Glass Powder (GP) to replace a portion of Type IL (Portland Limestone) cement. The mixes were made with a fixed water-to-binder ratio of 0.44 and contained 15% GP by mass while the CKD content ranged from 0% to 10%. The …

Supporting Programmers Answering The Hard-To-Answer Questions Through The Use Of Large Language Models, Haixin Zhou

McKelvey School of Engineering Graduate Student Theses & Dissertations

Programmers often face hard-to-answer questions when working on large-scale projects. Not only during team collaborations, but also during interruptions such as meetings, having to suddenly work on another project, or even just taking a break are major reasons these questions arise, as programmers have to regain the context, knowledge, and mental state to resume the work. Traditional text editors such as GitHub do provide a built-in history system, but they lack historical context behind the editing to answer such questions.

To address this issue, we developed an experimental extension, Code History, on Visual Studio Code (VS Code) in the hope …

Integration Of Highly Mismatched Iii-Sb Virtual Substrates On Silicon Via Interfacial Misfit Arrays For Short-, Mid-, And Long-Wave Infrared Applications, Trent Garrett

Boise State University Theses and Dissertations

Lattice constants of the III-V semiconductors range from 5.45 Å (GaP) to 6.48 Å (InSb). III-V semiconductors are grown on commercially available substrates made from binary III-V materials (e.g., GaAs, InP, and GaSb), or group IV materials (e.g., Si or Ge). These substrates offer very high quality, but only offer access to a small number of specific lattice constants. Given this constraint, it is desirable to develop growth methods that would allow the grower to modulate from the substrate lattice constant into the lattice constant of the material structure under investigation.

Device structures made from III-V semiconductors lattice-mismatched to these …

Failure Study Of Silicon Gated Field Emitter Arrays: Experiment And Simulation, Rushmita Bhattacharjee

Boise State University Theses and Dissertations

Silicon-based Gated Field Emitter Arrays (Si-GFEAs) are among the most well-developed field emitters. They are being actively explored for vacuum transistors and microwave vacuum electron devices due to their high-frequency performance, radiation resistance, and thermal stability up to 400 °C. However, their long-term reliability is limited by sudden failure events, resulting in cathodic vacuum arcs. This dissertation presents a combined experimental and simulation-based investigation into arc initiation mechanisms in Si-GFEAs. Different device arrays were tested under normal operation in vacuum at 10^-7 Torr with gate voltages of 50-70 V and emission currents from tens of nA to tens of µA. …

Engineering Properties And Stress-Strain Behavior Of Bcsa Concrete: Flexural Design Parameters, Strain Measurement Methods, And Models, Gabriel R. Johnson

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate (BCSA) cement concrete has gained popularity due to advantages over portland cement (PC), including, its fast-setting, high early strength gain, high durability, and reduced global warming potential. Though primarily used for pavement repair, it has good potential for structural applications. Building codes like ACI 318:19 permit alternative cement materials like BCSA cement if they can be shown to have adequate and predictable structural, durability, and fire performance comparable to PC concrete. This study evaluates the structural and mechanical behavior of BCSA cement concrete, measuring standard engineering properties and comparing results to PC concrete and code prediction equations. …

From Waste To Solution: Modeling And Characterization Of Grape Seed Bio-Waste For Phosphate Removal From Wastewater, Abeer Al-Bsoul, Zakaria Al-Qodah, Muhammad Tawalbeh, Khalid Bani-Melhem, Khalideh Al Bkoor Alrawashdeh, Mohammad Hailat, Ahmed A. Al-Taani, Eid Gul

All Works

In this study, particles of ground grape seeds were utilized to adsorb phosphate ions from a prepared solution, aiming to reduce phosphate concentration. Through a series of adsorption experiments, the effects of the adsorbent concentration, initial phosphate ion concentration, temperature, and pH on the phosphate ion uptake were studied. The removal efficiency of the phosphate ion decreased from 77 to 61% as a 25 to 45 °C increment in temperature was observed, which indicated the exothermicity in the adsorption process. The phosphate ion movement onto the adsorbent surface that exhibited the highest uptake value favored a neutral reaction environment with …

Mathematical Modeling Of Effects Of Tumor Location On Lung Function., Lamargaret Temukisa Johnson

Master of Engineering Theses

Lung cancer has the highest rates of incidence and mortality of all cancers. Most lung cancer tumors are Non-Small Cell Lung Cancer (NSCLC). NSCLC patients with lesions in the upper lobes are found to have better prognosis compared to those with lesions in the middle and lower lobes. Previous studies have suggested various causes for this discrepancy at both the organ-scale and tissue-scale. To model NSCLC growth in different locations within the lung, an organ scale lung model and tissue scale tumor model were coupled through the tissue pressure, and oxygen and carbon dioxide partial pressures. The coupling was used …

Feasibility Study On Using Blue Clay As A Supplementary Cementitious Material (Scm)., Clark Lemon

Master of Engineering Theses

An effective strategy for reducing CO₂ emissions in the global cement industry is replacing a percentage of cement with supplementary cementitious materials (SCMs). As the availability of conventional SCMs such as fly ash and slag is decreasing, alternative SCMs such as calcined clays have been studied for their use as effective pozzolans. The present work investigates the feasibility of using a waste product from the quarrying industry known as blue clay as a viable SCM. It is composed of multiple clay minerals, predominantly muscovite. Raw and calcined at four temperatures (500, 650, 800, and 950°C), blue clay was analyzed …