Engineering Commons^™

Investigation Of Post-Acid Stimulation Impacts On Well Performance Using Fracture Modeling And Reservoir Simulation In A Jurassic Carbonate Reservoir, Muaath Alansari

Masters Theses

"Well stimulation (well fracturing) became an essential tool in the Oil and Gas industry to unlock the potential of unconventional reservoirs all over the world and especially in the Middle East. In Kuwait, well stimulation is obligatory when dealing with deep Jurassic carbonate reservoirs. Thus, the well fracture designing process plays a very critical role in determining the success of the stimulation job and the improvement of the recovery.

Several wells stimulated with 20% HCL have shown wide variations in both short and long term well production performance. The research aims to investigate and identify the possible reasons causing these …

Power Generation From Waste Heat During Oil Production, Subrahmanya Chandra Bhamidipati

Masters Theses

"The increase in the world population is causing a significant increase in the global demand for energy. This rise in demand is generally met with the use of fossil fuels. But there is considerable pressure to lessen the release of carbon through the combustion of fossil fuels. One way that the oil and gas industry can provide increased energy without carbon combustion is by extracting the latent heat energy contained in produced oil, gas and water from producing reservoirs, and from water which is cycled through depleted, end-of-life or abandoned reservoirs. Extracting this energy and using it to provide direct …

Mechanical Activation And Cation Site Disorder Of Spinel-Based Ceramics, Cole A. Corlett

Masters Theses

"This research focuses on the processing and the effects that has on the cation disorder of magnesium-aluminate spinel based (MgAl₂O₄) ceramics. The first goal of this project was to determine the effects of high-energy milling, i.e., mechanical activation, on cation disorder (inversion) within the spinel structure. First, 1:1 molar ratios of MgO:Al₂O₃ ceramics were processed using two green processing methods, ball milling (XD) and SPEX milling (mechanical activation, MA) followed by a subsequent annealing treatment in air to form a single spinel phase in each powder sample. Neutron diffraction analysis was employed to …

The Field Coupling Mechanism Study For Near Field Probe, Shun Liu

Masters Theses

"In this part, the radius of the loop is used to predict the voltage induced by the E- field in the circular loop antenna. The thin rectangle loop and thick rectangle loop have been investigated. The equivalent radius of the rectangle loop is estimated by the average of the one over the distance between the points on the loop to the center of the loop. The estimation matches with the numerical simulation"--Abstract, page iv.

Relationships Among Mineralogy, Geochemistry, And Oil And Gas Production In The Tuscaloosa Marine Shale, Hayley Roxana Beitel

Masters Theses

"The Tuscaloosa Marine Shale (TMS) is an unconventional shale reservoir located in southeast Louisiana and southwest Mississippi. Limited mineralogical and geochemical data for the TMS have been published. The data that do exist indicate that the formation is heterogeneous. Consequently, previous investigators and oil and gas companies have not managed to effectively link mineralogical and chemical changes to oil and gas production in the TMS. These linkages are critical to establish for future exploration efforts. In this study, we attempt to establish these relationships by gathering all existing mineralogical and chemical data in the TMS, including newly acquired data from …

Toward Understanding Commercial Additives For Zincate Electrogalvanizing, Margaret Scott

Masters Theses

"Cyanide zinc electrogalvanizing has been used for many years to produce high quality and uniform zinc coatings. Due to toxicity concerns, a significant amount of research has occurred to remove the use of cyanide while still producing a similar deposit. One of the resulting plating chemistries is the alkaline zincate bath.

Alkaline zincate plating has the advantages of low startup cost, low toxicity, and low corrosion rate. Despite these advantages, alkaline bath conditions do not produce acceptable zinc deposits without the use of plating additives, which can promote lustrous, smooth deposits. This research aims to: (1) generate fundamental electrochemical data …

Analysis Of Refracturing Activities In The Major Shale Plays In The United States, Faisal Shammam

Masters Theses

"Refracturing of existing horizontal multistage wells has increased over the past decade in the oil industry. This work aims to investigate all the refracturing operations in the most active shale plays in the united states (Bakken, Niobrara, Marcellus, Permian, Eagle Ford, Barnett, and Haynesville) in terms of completion technique, candidate selection, treatment types, and refracturing production efficiency. To collect the data of the refractured wells, an advanced data analytics approach was applied to separate the refractured wells from 170,000 wells reported in FracFocus, a public chemical registry for hydraulic fracturing in the United States, and combine it with DrillingInfo database, …

Projectile Generator Design For Underground Coal Mine Seal Testing, Ethan Allan Steward

Masters Theses

"Underground coal mines have several dangers, one of the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at …

A Simple Background Elimination Method For Miniaturized Fiber-Optic Raman Probe, Bohong Zhang

Masters Theses

"Raman scattering is called a photonic - molecular interaction based on the kinetic model of the analytic. Due to the uniqueness of the Raman scattering technique, it can provide a unique fingerprint signal for molecular recognition. However, a serious challenge often encountered in Raman measurement comes from the requirements of fast, real-time remote sensing, background fluorescence suppression, and micro-environmental detection.

A new Miniaturized Fiber-Optic Raman Probe (MFORP) for Raman spectroscopy, used especially for eliminating background fluorescence and enhancing sampling, is presented. Its main purpose is to provide an overview of excellent research on the detection of very small substances and …

Optimization Of Transit Smart Card Data Publishing Based On Differential Privacy, Chenxi Chen

Masters Theses

“Privacy budget allocation is a key step of the differential privacy (DP)-based privacy-preserving data publishing (PPDP) algorithm development, as it directly impacts the data utility of the released dataset. This research describes the development of an optimal privacy budget allocation algorithm for transit smart card data publishing, with the goal of publishing non-interactive sanitized trajectory data under a differential privacy definition. To this end, after storing the smart card trajectory data with a prefix tree structure, a query probability model is built to quantitatively measure the probability of a trajectory location pair being queried. Next, privacy budget is calculated for …

Method Of Optimal Battery Scheduling With Optimal Battery And Photovoltaic Sizing, Gideon Hallman

Masters Theses

“Renewable energy generation is on the rise. One of the best ways to capitalize on this intermittent power supply is by using the renewable energy source in tandem with batteries. A joint photovoltaic (PV) and battery system model was created that implemented battery degradation and optimized battery usage using a Markov Decision Process (MDP). This system was then subjected to a series of tests to do a sensitivity analysis while optimizing the battery and PV sizing for the system at hand. Parametric sweeps of solar power and battery capital costs, the cost of energy taken from the grid, the cost …

The Role Of Psychological Reactance In Smart Home Energy Management Systems, Matthew Thomas Heatherly

Masters Theses

“With an ever-growing demand for energy, our increasing consumption is producing more greenhouse gases and other pollutants, impacting climate change. One approach to reducing residential energy consumption is through the use of smart energy management systems. However, automation from smart technology inherently removes a certain amount of control from the user. If loss of control is perceived as a loss of freedom, this may lead users to experience psychological reactance when using these products. A set of experiments was conducted to assess how three features of a message notification from smart home energy management systems may induce reactance in users. …

A Physics-Based Pi Pre-Layout Tool For Pcb Pdn Design, Shuang Liang

Masters Theses

"With increasingly stringent requirements for lower voltage supply, and higher density in PCB PDN design, now integrity (PI) is an increasingly important aspect that must be considered. A pre-layout tool based on the Cavity Model and Boundary Element Method is built to automatically achieve a specified target impedance for a multi-layered Printed Circuit Board (PCB) Power Distribution Network (PDN) design with a minimal number of decoupling capacitors.

The pre-work about the post-layout design and analysis is proposed and the guidelines for creating a decoupling capacitors network with better performance has been built. With limit inputs, physical limitations for the minimal …

Development Of Complex Lattice Cell In Benchmark Model Of Particle Bed Critical System, Elijah Chamberlain Lutz

Masters Theses

“Criticality safety benchmark evaluations require the creation of models that most accurately represent the experiment being evaluated. In some cases this can be relatively trivial with experiments containing rather simple or standard geometry. In others, such as packed bed systems, this becomes unique and a more difficult process. The importance of accurate modeling of packed bed systems for the use of criticality safety benchmark evaluations was looked at. Four models were created of various complexities and accuracy. First the multi-particle bed, consisting of a fuel particle (UC_1.7 kernel with C shell) and two filler particles (Zircaloy-4 and C + …

Design And Evaluation Of The 3d Printed Electromagnetic Absorber Built With Conductive Carbon-Filled Filament, Rui Mi

Masters Theses

"This research presents an application of the resistive frequency selective surface (FSS) fabricated with a 3D printed conductive material as an electromagnetic absorber for the EMI-reducing door. This solution allows to reduce radiated emissions of a router system. The resistive frequency selective surface has a three-layer structure. The top layer is a 3D printed FSS pattern, the middle layer is an air gap, and the bottom layer is a metal plane.

The first paper presents the methodology for manufacturing a frequency selective surface using the 3D printing technology, including the material characterization, design, fabrication, and evaluation.

The unpublished content presents …

The Effects Of Rigid Polyurethane Foam As A Confinement Material On Breaching Charge Detonations, Nathan Franz Paerschke-O'Brien

Masters Theses

"The effects of a rigid polyurethane foam used as a confinement material on four types of breaching explosives were tested, focusing on the changes in shockwave peak pressures, detonation load compression forces, and brisance cratering abilities. The Plate Dent testing procedure was modified to incorporate a load cell force sensor, and two air overpressure sensors were included adjacent to the blast to quantify each test result. The testing variables focused on the polyurethane foam cure times and thickness volumes around the breaching explosives to determine the breaching charges' optimal energy output capabilities when confined by the foam material. The rigid …

Investigation Of The Sensitivity Of Human Arm To Small Interaction Forces During Physical Human-Robot Interaction (Phri), Fazlur Rashid

Masters Theses

“Understanding the human motor control strategy during physical interaction tasks is crucial for developing future robots for physical human-robot interaction (pHRI). Effective pHRI depends on humans communicating their intentions for movement with robots. In physical human-human interaction (pHHI), small interaction forces are known to convey their intent between the partners. It is speculated that small interaction forces contain significant information to convey the movement intention of pHHI. However, the mechanism underlying this interaction strategy is largely unknown. Hence, the aim of this work was to investigate what affects humans’ sensitivity to the interaction forces. The hypothesis was that small interaction …

Early Wildfire Detection By Air Quality Sensors On Unmanned Aerial Vehicles: Optimization And Feasibility, Doaa Rjoub

Masters Theses

“Millions of acres of forests are destroyed by wildfires every year, causing ecological, environmental, and economical losses. The recent wildfires in Australia and the Western U.S. smothered multiple states with more than fifty million acres charred by the blazes. The warmer and drier climate makes scientists expect increases in the severity and frequency of wildfires and the associated risks in the future. These inescapable crises highlight the urgent need for early detection and prevention of wildfires. This work proposed an energy management framework that integrated unmanned aerial vehicle (UAV) with air quality sensors for early wildfire detection and forest monitoring. …

Transfer Function Measurement For Automotive Intentional Emi And Thermal Runaway Investigation Of Lithium-Ion Battery By Intentional Emi, Woncheol Song

Masters Theses

"With an increasing demand for electric vehicles and autonomous driving, many components of a vehicle are being replaced as electric components. This implicates the possibility of an increase in the malfunction of electric components due to unknown electromagnetic interferences. In this reason, malicious intentional electromagnetic interference (IEMI) is being considered as a growing threat for the current and next generation of automotive technology.

In the first topic, the transfer function between the IEMI attacker and the engine control unit (ECU) circuit in an automobile is extracted to analyze how the IEMI affects the vehicle.

In the second topic, to mimic …

Bond Graph Modeling Of Critical Infrastructures For Cyber-Physical Security Implementation, Michele Jane White

Masters Theses

“In developed societies, there exists infrastructure vital to everyday life. This includes water and power systems. Technology is quickly evolving and being implemented on these utilities. This technology can range from smart metering in neighborhoods to volume sensors in local waste water treatment facilities. When networking, sensing, monitoring, or control devices are integrated with infrastructure it is considered a cyber physical system, or CPS. When information about an important physical system is connected to the virtual world, it is opened up to security risks. Cyber security can be provided to the CPS by monitoring the physical state of the system …

Multiple-Site Fatigue Cracking Methodology To Assess Structural Integrity Of Aircraft Riveted Panels, Haroldo Chacon

Masters Theses

“Multiple Site Damage (MSD) is the most common source of Widespread Fatigue Damage (WFD) affecting structural integrity of aging aircraft fleets. Therefore, an understanding of its progression, the development of methods to prevent the onset, and the maintenance procedures precluding WFD are important to improve aircraft fleet longevity. A reliable and efficient numerical methodology to perform detailed Multiple Site Damage assessment in riveted structural joints was developed. A probabilistic methodology was employed in conjunction with Monte Carlo simulation technique; the fatigue initiation life at every potential crack initiation site was determined and initial damage scenarios were generated. Probabilistic crack growth …

Fabrication Of Silicon Nitride Parts By Ceramic On-Demand Extrusion Process, Sachin Choudhary

Masters Theses

“Ceramic On-Demand Extrusion (CODE) is a patented solid freeform fabrication method for manufacturing high-density monolithic ceramic parts. In the past 5-6 years, the technology has been successfully implemented to fabricate alumina and zirconia parts. The mechanical characterizations also show CODE’s high potential in achieving desired structural properties. The present study covers the fabrication of silicon nitride parts by CODE process, which entailed the design of paste formulation for achieving rheology suitable for dimensional control in fabricated parts and determining firing temperature and the content of sintering additives for silicon nitride green bodies fabricated by CODE. The density, hardness, and fracture …

A Compact Wavelength Meter Using A Multimode Fiber, Ogbole Collins Inalegwu

Masters Theses

“Wavelength meters are very important for precision measurements of both pulses and continuous-wave optical sources. Conventional wavelength meters employ gratings, prisms, interferometers, and other wavelength-sensitive materials in their design. Here, we report a simple and compact wavelength meter based on a section of multimode fiber and a camera. The concept is to correlate the multimodal interference pattern (i.e., speckle pattern) at the end-face of a multimode fiber with the wavelength of the input lightsource. Through a series of experiments, specklegrams from the end face of a multimode fiber as captured by a charge-coupled device (CCD) camera were recorded; the images …

Research And Development Of A Laser Hot Wire Deposition Process, Christopher Croft

Masters Theses

“Laser hot wire directed energy deposition (DED) is an increasingly popular method for improving deposition rates and overall reduction of build times in DED processing. While there is clear benefit, it is important to fully understand the impact of preheating the wire. This work focuses on developing a model that describes bead geometry output using all factors including the wire preheat. The model was fit with over 150 data points that explored a large range of each factor. The resulting model was then leveraged to evaluate a process control variable. The technique chosen used feedback from the hot wire system …

Analysis And Design Of Dc-Link Capacitor In Cascaded H-Bridge Multilevel Active Front-End Converter, Muhammad Shehroz Malik

Masters Theses

Medium-voltage grid-tied systems often use a cascaded H-bridge multi-level active front-end. In this converter, dc link bus capacitors play an important role in stabilizing the converter and enabling both active and reactive power injections. The present work provides analytical expressions for the capacitor current, which are essential for optimizing system design (especially capacitor size vs. lifetime). Then, the expression is incorporated into the grid connected bidirectional power system model. Consequently, this work contributes to the guiding principles to choose accurate dc link capacitor ratings against grid-side power delivery requirements.

DC-link capacitors come with an expiration date which is dependent on …

Effect Of Spike Anchors On The Bond Behavior Of Steel Reinforced Polymer Composite Externally Bonded To A Concrete Substrate, Keenan Lorence Mcburney

Masters Theses

Steel reinforced polymer (SRP) composites are a strengthening material that consist of continuous high-strength steel cords embedded in a polymeric matrix. SRP has demonstrated a high potential for providing additional flexural and shear strength in existing concrete structures when bonded to the concrete surface. However, premature debonding from the concrete substrate at low load levels is a major shortcoming of SRP composites. It has been demonstrated in previous studies that anchors can limit the effect of debonding in fiber reinforced polymer (FRP) composites by increasing the load capacity and ductility of the composite-concrete interface.

This study aims to investigate the …

Physics-Based Modeling Of Lithium-Ion Batteries For Control And Estimation Applications, Brody J. C. Riemann

Masters Theses

“Lithium-ion batteries are extensively used in many application areas like consumer electronics, electric vehicles, and microgrids. As the world moves towards further electrification of vehicles and more widespread use of renewable energy sources, the need for large-scale battery storage systems will grow. To effectively replace conventional methods, batteries will need to be charged quickly while accounting for degradation to maximize lifetime. Further, larger batteries require more detailed safety monitoring, which is implemented using a battery management system (BMS). A BMS is responsible for state of charge (SOC) estimation, state of health (SOH) estimation, cell balancing, regulating voltage and current according …

Seed Modeling Of An Esd Gun Discharge To A Usb Cable, Yang Xu

Masters Theses

“An IC protected by a transient voltage suppression (TVS) diode may fail if the TVS device does not turn on or does not turn on quickly enough, causing the IC to take the full brunt of the electrostatic discharge (ESD) event. Transient simulation models have been developed for ESD protection devices for the purpose of system-efficient ESD design (SEED). The TVS modeling methodology has been improved to better represent the physics that occurs during the TVS response and more accurately predict the interactions between off-chip and on-chip protection devices. Moreover, a complicated test scenario -- an ESD gun discharge through …

Topological Biclustering Artmap, Raghu Yelugam

Masters Theses

”Detection of gene mutations is central for assessing genetic factors affecting disease predisposition, genetic causes of a particular disease, and gene-targeted treatment. DNA microarray methods are widely used to detect mutations by contrasting the expression levels of thousands of genes together under varying experimental conditions. The experimental conditions could be diseased cell states compared with the normal cell states. Biclustering, a robust exploratory data analysis tool, can be applied to microarray data to detect subsets of genes that co-express highly only for a subset of experimental conditions. Such detection is crucial for gaining insights into gene regulatory networks, differential gene …

Axial Performance Of Self-Consolidating Concrete-Filled Fiber Tubes, Joshua David Carter

Masters Theses

"Concrete filled fiber tubes can be used to increase ductility and strength of a concrete member and self-consolidating concrete is an ideal material to use in practical applications of concrete-filled fiber tubular columns. However, the propensity of self-consolidating concrete to autogenous shrinkage could reduce the effectiveness of the concrete confinement. This research investigates the use of self-consolidating concrete in pre-cast FRP tubes and various methods of shrinkage reduction and compensation to increase the axial performance of said self-consolidating concrete-filled fiber tubes. Axial compression tests were performed under monotonic and cyclic conditions to determine the stress-strain relationship of the self-consolidating concrete …