Engineering Commons^™

Fuel Consumption Models For Tractors With Partial Drawbar Loads, Bryan Jeffrey Smith

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Three models for predicting fuel consumption for agricultural tractors with partial drawbar loads were compared. Data were collected from eight John Deere tractors, JD 7230R (e23), 7250R (e23), 7270R (e23), 7290R (e23), 7290R (IVT), 8320R (16 speed), 8345RT (IVT), 8370R (IVT). The tractors were tested with 7 load levels per speed at four different travel speeds as close as possible to 4, 7.5, 10, and 13 km·h^-1. The IVT tractors were operated in Auto mode and the geared tractors were shifted up three gears and throttled back to the same travel speeds as the IVT tractors. The 7 …

Subjective Perception Of Varying Reflection Densities In Room Impulse Responses, Hyun Hong

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Reverberation time (RT) is a metric commonly used to describe room acoustic conditions, but different rooms which have the same reverberation time can have different reflection densities. Much less is known about how humans perceive different reflection densities and how sensitive humans are to changes in reflection density. Previous investigations in the existing literature have studied the upper limit of distinguishable reflection density using artificial impulse responses, but not with more realistic impulse responses simulated in room acoustic software or measured from real rooms. The aim of this dissertation is to investigate methods for quantifying reflection density from measured impulse …

Heat Transfer Mechanisms In Water-Based Nanofluids., Masoudeh Ahmadi

Electronic Theses and Dissertations

Nanofluids are a class of heat transport fluids created by suspending nano-scaled metallic or nonmetallic particles into a base fluid. Some experimental investigations have revealed that the nanofluids have remarkably higher thermal conductivities than those of conventional pure fluids and are more suited for practical application than the existing techniques of heat transfer enhancement using millimeter and/or micrometer-sized particles in fluids. Use of nanoparticles reduces pressure drop, system wear, and overall mass of the system leading to a reduction in costs over existing enhancement techniques. In this work, the heat transfer coefficient is determined experimentally using copper oxide (CuO) based …

Assessing The Water Quality Benefits Of Green Infrastructure Stormwater Control Measures., Sam Abdollahian

Electronic Theses and Dissertations

Permeable pavements systems and tree boxes are a common type of Green Infrastructure (GI) Stormwater Control Measures (SCMs) that are often used for mitigating the stormwater runoff. In this study two permeable pavement systems and a tree box installed along parking lanes of an urban street in Louisville, KY, were investigated to evaluate their performance on improving stormwater runoff quality. The water quality monitoring was accomplished by analysis of samples collected from stormwater runoff and the captured stormwater volume at the bottom of the permeable pavements’ sub-base reservoir and by a drain gauge (lysimeter) installed in the tree box. Pollutants …

Development Of A Vascularized, Induced Pluripotent Stem Cell-Derived Liver-Tissue Mimic For Therapeutic Applications., Venkat Madhav Ramakrishnan

Electronic Theses and Dissertations

This dissertation describes the incorporation of several technologies (stem cells, gene therapy, tissue engineering and regenerative medicine) into a single project that aims to produce a liver-tissue mimic for therapeutic applications. The liver is arguably one of the most complex organs in the body. In addition to its remarkable capacity to regenerate, it performs a host of vital functions. As a result, its impairment has widespread systemic consequences. The work described herein focused on the liver in the context of cardiovascular disease and used the heritable disorder Familial Hypercholesterolemia (FH) as a clinical disease model. As (a) the only definitive …

Exclusive-Or Preprocessing And Dictionary Coding Of Continuous-Tone Images., Takiyah K. Cooper

Electronic Theses and Dissertations

The field of lossless image compression studies the various ways to represent image data in the most compact and efficient manner possible that also allows the image to be reproduced without any loss. One of the most efficient strategies used in lossless compression is to introduce entropy reduction through decorrelation. This study focuses on using the exclusive-or logic operator in a decorrelation filter as the preprocessing phase of lossless image compression of continuous-tone images. The exclusive-or logic operator is simply and reversibly applied to continuous-tone images for the purpose of extracting differences between neighboring pixels. Implementation of the exclusive-or operator …

Application Of The Aeroacoustic Analogy To A Shrouded, Subsonic, Radial Fan., Bryan Buccieri

Electronic Theses and Dissertations

A study was conducted to investigate the predictive capability of computational aeroacoustics with respect to a shrouded, subsonic, radial fan. A three dimensional unsteady fluid dynamics simulation was conducted to produce aerodynamic data used as the acoustic source for an aeroacoustics simulation. Two acoustic models were developed: one modeling the forces on the rotating fan blades as a set of rotating dipoles located at the center of mass of each fan blade and one modeling the forces on the stationary fan shroud as a field of distributed stationary dipoles. Predicted acoustic response was compared to experimental data. The blade source …

Plasma Catalysis Using Low Melting Point Metals., Maria Carreon

Electronic Theses and Dissertations

Plasma catalysis is emerging as one of the most promising alternatives to carry out several reactions of great environmental importance, from the synthesis of nanomaterials to chemicals of great interest. However, the combined effect of a catalyst and plasma is not clear. For the particular case of 1-D nanomaterials growth, the low temperatures synthesis is still a challenge to overcome for its scalable manufacturing on flexible substrates and thin metal foils. Herein, the use of low-melting-point metal clusters under plasma excitation was investigated to determine the effectiveness in their ability to catalyze the growth of 1-D nanomaterials. Specifically, plasma catalysis …

Automatic License Plate Recognition Using Deep Learning Techniques, Naga Surya Sandeep Angara

Electrical Engineering Theses

Automatic License Plate Recognition (ALPR) systems capture a vehicles license plate and recognize the license number and other required information from the captured image. ALPR systems have number of significant applications: law enforcement, public safety agencies, toll gate systems, etc. The goal of these systems is to recognize the characters and state on the license plate with high accuracy. ALPR has been implemented using various techniques. Traditional recognition methods use handcrafted features for obtaining features from the image. Unlike conventional methods, deep learning techniques automatically select features and are one of the game changing technologies in the field of computer …

Virtual Electronics Laboratory For Visualized Education And Training, Sreelatha Aihloor Subramanyam

Electrical Engineering Theses

On-line education is utilized extensively and has been found to be effective in a multitude of subject areas, including engineering education. However, for on-line education to be fully effective in engineering education, a means must be developed to provide on-line students with laboratory experiences that achieve the same learning outcomes as face-to-face laboratories. To address this need, a pilot computer program, Project VELVET (Virtual Electronics Laboratory for Visualized Education and Training), for a virtual electronics laboratory is being developed. VELVET operates on Windows-based computers in a real-time environment. It presents to its user a virtual breadboard into which components may …

Identification Of Color Properties Of Mangos Using Image Analysis, Md Towfqur Rahman

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

In this project work carried out the application of a simple machine vision system was used to measure the different color properties of mango fruit surface for grading operation. In the context of agricultural post-harvest activity, labor shortage and timeliness of operation, manual grading of fruits and other agricultural products are laborious and costly. Now-a-days non-destructive machine vision technology is used to process various post harvest operation of biological products according size, shape, defects, etc. A CCD camera with fluorescent lighting system is used to capture the mango images into the visible light region. Then the images were analyzed by …

Control Of Cation Ordering In Zinc Tin Nitride And In-Situ Monitoring Of Growth, Brian Christopher Durant

Masters Theses

Semiconducting materials with a band gap around 1.5 eV are very much sought after due to their close match to the solar spectrum. However, some compounds that have shown promise for highly efficient solar cells contain rare, expensive, and sometimes toxic elements, such as indium and gallium. As such, a search for earth abundant materials has become more prominent recently. One such earth abundant semiconducting material that has garnered interest is ZnSnN₂. It has been shown through previous studies that there is the possibility of continuously tuning the band gap between 1.0 and 2.0 eV by controlling the …

Industrial Energy Consumption, Benchmarking, And Analysis In The United States, Daniel Maldonado

Mechanical Engineering Undergraduate Honors Theses

The purpose of this paper is to analyze the energy consumption of the industrial sector in the United States, and to identify the tools that can be used to minimize the consumption and improve the energy efficiency of all facilities in the country. The first part of the paper is a historical analysis of the industrial sector energy consumption, where the different energy sources are identified. The second part details different electronic tools that will provide facilities the ability of performing benchmarking, in order to understand their energy performance. Finally, the third part of this paper provides information about the …

A Look At Commercial Building Energy Use And Energy Efficiency Technologies From 1980 To Present, Marvin M. Arroyo

Mechanical Engineering Undergraduate Honors Theses

Energy consumption has increased considerably in the last fifty years as population rises. At the same time, design and efficiency of all equipment used in commercial buildings have changed as well. The purpose of this thesis is to explain how HVAC systems have changed and how they have affected energy consumption. Entities like the US Department of Energy (DOE) and the US Energy Information Administration (EIA) facilitate the data-gathering process by offering databases of energy information from actual monthly energy bills to promote public understanding of energy and its interaction with the economy and the environment. Moreover, in order to …

Molecular Dynamics Simulation Of Force-Controlled Nanoindentation, Keaton Jaramillo

Mechanical Engineering Undergraduate Honors Theses

The aim of this honors research is to develop a force-controlled nanoindentation algorithm for molecular dynamics simulation. The algorithm was tested on Silicon using the Tersoff potential and Gold using the Embedded-Atom Method (EAM) potential. The effect of varying the damping parameters that adjust the system pressure and changing run length between force iterations is explored. The force-controlled algorithm was developed and shown to be working by correlating pop-in events shown in the force versus displacement (P-h) curves to visualization software showing phase transformation or dislocation events in the sample.

Morphology Based Framework For Improved Driver's Visibility In Inclement Weather Conditions, Saleem Farhood Hussein

Masters Theses

The U.S. Department of Transportation reports that on average there are 5,870,000 vehicle accidents each year. Twenty-three percent (23%) of these accidents are attributed to weather conditions with an annual average of more than 6,000 people are killed and 480,000 people are injured. Weather-related accidents occur mainly because of the low visibility on the roads under inclement conditions such as snow, rain and fog. While these conditions can be predictable and individuals try to avoid driving in inclement weather, there are circumstances that require driving in such conditions such as emergency responders or when the severity of the storm has …

Storage Of Round And Square Switchgrass Bales: Effect Of Storage Time And Fungal Inoculation On Saccharification Efficiency, Noaa Frederick

Graduate Theses and Dissertations

To produce fermentable sugars from lignocellulosic biomass feedstock, severe pretreatment conditions are needed (either high acid concentration, temperature, or retention times). High severities can produce toxic byproducts which inhibit enzymatic hydrolysis or fermentation. In order to reduce pretreatment severities (and thus increase enzyme and fermentation efficiency), the white-rot fungus Pleurotus ostreastus was seeded into square and round bales of Kanlow switchgrass (Panicum virgastum L.) and left in the field over a period of 9 month. The laccase producing fungus is believed to selectively degrade lignin, a common plant structural polymer, which can function as an enzymatic inhibitor. Samples were taken …

Impact Of Constructing A Low Crested Weir In Cape Canaveral On Flushing In The Banana River, Atousa Saberi

Theses and Dissertations

The purpose of this study is to determine the extent to which constructing a low crested weir adjacent to Port Canaveral improves ushing in the Banana River. The Banana River is a 50 km long sub-basin of Indian River Lagoon (IRL), located between Cape Canaveral and Merritt Island in Brevard County. Although Port Canaveral locks connect the Banana River to the ocean, the locks remain closed when there are no passing vessels; therefore, it has limited circulation and a long ushing time. Declining water quality can be linked to recent high mortality events of di erent species living in the …

An Open-Source, Automated Chemical Vapor Deposition System For The Production Of 2d Materials, Dale Brown

Boise State University Theses and Dissertations

While interest in two-dimensional materials has exploded in recent years, the high cost of chemical vapor deposition (CVD) systems can act as a barrier to entry for some researchers interested in studying these materials. This thesis presents an open-source design for an automated CVD that can be built for a fraction of the cost of similarly capable commercial systems and that can easily be customized and expanded.With a CVD built as described,growth of high quality graphene and graphene foam is demonstrated.These results highlight the flexibility of the open-source design in producing a variety of nanomaterials, which are at the forefront …

Plastic Deformation And Effective Strain Hardening Coefficient Of Irradiated Fe-9wt%Cr Ods Alloy By Nano-Indentation And Tem, Corey Kenneth Dolph

Boise State University Theses and Dissertations

The objective of this study is to characterize changes in the yielding, and effective strain hardening coefficient of an oxide dispersion strengthened (ODS) alloy upon exposure to irradiation. It is well known that irradiation produces a supersaturation of defects, which alters the mechanical properties of a material. In order to engineer materials for use in advanced nuclear reactors, the long-term effects of neutron irradiation on mechanical performance must be understood. However, high-dose neutron exposure is often simulated using ion bombardment. Unfortunately, ion irradiation results in a shallow damage layer that prevents traditional bulk mechanical characterization methods from being utilized. A …

Effects Of Expected Service Life Exposures On The Functional Properties And Impact Performance Of An American Football Helmet Outer Shell Material, David E. Krzeminski

Dissertations

The purpose of this dissertation is to gain a greater scientific understanding of the changes in functional material properties and impact performance of an American football helmet outer shell material under expected service life exposures. The research goals are to (i) quantify chemical, physical, thermal, and mechanical degradation of an American football outer shell material under expected environmental conditions and (ii) develop a linear drop test impact protocol to employ expected on-field impact conditions to American football helmet components and a plaque-foam (i.e., shell-liner) surrogate. Overall, a step-wise progression of analysis was demonstrated to concurrently quantify and understand changes in …

Hybrid Aryl-Ether-Ketone And Hyperbranched Epoxy Networks, John Misasi

Dissertations

In this dissertation, relationships between chemical structures, cure kinetics and network architectures are correlated to bulk mechanical properties for novel, hybrid epoxy-amine networks. The work is split into two primary sections: the first is the synthesis and characterization of multifunctional glassy networks based on aryl-ether-ketone diamine curatives, while the second is based on the synthesis and characterization of hyperbranched epoxy polymers and their resulting networks.

Three aryl-ether-ketone (AEK) diamines of increasing molecular weights were synthesized and used to cure 4,4’-tetraglycidylether of diaminodiphenylmethane (TGDDM); the resulting networks were compared to 4,4’-diaminodiphenyl sulfone cured TGDDM. Architectural differences were created by varying cure …

Polyacrylonitrile Copolymers: Effects Of Molecular Weight, Polydispersity, Composition, And Sequencing On Thermal Ring-Closing Stabilization, Jeremy D. Moskowitz

Dissertations

Controlled polyacrylonitrile (PAN)-based carbon fiber precursors with defined molecular weights, polydispersities, compositions, and architectures have been prepared for their study on thermal ring-closing stabilization behavior. PAN and its copolymers of number average molecular weights exceeding 170,000 g/mol were successfully synthesized via low temperature reversible addition-fragmentation chain transfer (RAFT) polymerization. RAFT polymerizations of PAN-based precursors were compared to conventional free radical solution polymerizations with a focus on the effects of molecular weight and polydispersity on structural evolution and cyclization efficiency. When RAFT polymerization was extended to copolymers, it was found that RAFT copolymers achieved greater cyclization intensities and improved thermal stability …

Development Of Dual-Cure Hybrid Polybenzoxazine Thermosets, Jananee Narayanan Sivakami

Dissertations

Polybenzoxazines are potential high performance thermoset replacements for traditional phenolic resins that can undergo an autocatalytic, thermally initiated ring - opening polymerization, and possess superior processing advantages including excellent shelf-life stability, zero volatile loss and limited volumetric shrinkage. The simplistic monomer synthesis and availability of a wide variety of inexpensive starting materials allows enormous molecular design flexibility for accessing a wide range of tailorable material properties for targeted applications. Despite the fact, once fully cured, benzoxazines are difficult to handle due to their inherent brittleness, leaving a very little scope for any modifications. The motivation of this dissertation is directed …

Face Recognition With Multi-Stage Matching Algorithms, Xianming Chen

Dissertations

For every face recognition method, the primary goal is to achieve higher recognition accuracy and spend less computational costs. However, as the gallery size increases, especially when one probe image corresponds to only one training image, face recognition becomes more and more challenging. First, a larger gallery size requires more computational costs and memory usage. Meanwhile, that the large gallery sizes degrade the recognition accuracy becomes an even more significant problem to be solved.

A coarse parallel algorithm that equally divides training images and probe images into multiple processors is proposed to deal with the large computational costs and huge …

Use Of Personality Profile Assessments In The Construction Industry, Brian Richard Childs

Theses and Dissertations

Various industries are using personality profile assessments as tools to help reduce employee turnover. Employee turnover is a continuing challenge in the construction industry that has negative effects on construction companies. Research found that it was difficult to know if companies in the construction industry are using personality profile assessments as a tool to help reduce employee turnover. After understanding that other industries were using personality profile assessments in their hiring, promoting, team building and leadership development to reduce turnover, it was desired to understand if the construction industry was doing the same. This research performed a survey among the …

A Pilot Study To Determine The Performance Of Tension Lap Splices In Reinforced Masonry Made With Light-Weight Grout, Brandon Richard Corbett

Theses and Dissertations

The use of light-weight building materials in modern construction has resulted in efficient designs and considerable cost savings by reducing structural weight and supporting sections. This has only been possible because of many years of research to better understand the properties of the light-weight material, and its structural behaviors. However, light-weight grout is a relatively new building material in reinforced masonry construction and little is known about its structural properties. The main objective of this study was to determine if the use of light-weight grout would impact the performance of reinforcing steel, specifically development length, in masonry construction.The research included …

Rubidium Packaging For On-Chip Spectroscopy, Cameron Louis Hill

Theses and Dissertations

This thesis presents rubidium packaging methods for integration using anti-resonant reflecting optical waveguides (ARROWs) on a planar chip. The atomic vapor ARROW confines light through rubidium vapor, increases the light-vapor interaction length, decreases the size of the atomic cell to chip scales, and opens up possibilities for waveguide systems on chips for additional optoelectronic devices. Rubidium vapor packaging for long-life times are essential for realizing feasibly useful devices. Considerations of outgassing, leaking and chemical compatibilities of materials in rubidium vapor cells lead to an all-metal design. The effect of these characteristics on the rubidium D2 line spectra is considered.

Laboratory Resilient Modulus Measurements Of Aggregate Base Materials In Utah, Kirk David Jackson

Theses and Dissertations

The Utah Department of Transportation (UDOT) has fully implemented the Mechanistic-Empirical Pavement Design Guide for pavement design but has been using primarily level-three design inputs obtained from correlations to aggregate base materials developed at the national level. UDOT was interested in investigating correlations between laboratory measurements of resilient modulus, California bearing ratio (CBR), and other material properties specific to base materials commonly used in Utah; therefore, a statewide testing program was needed. The objectives of this research were to 1) determine the resilient modulus of several representative aggregate base materials in Utah and 2) investigate correlations between laboratory measurements of …

Springback Force Considerations In Compliant Haptic Interfaces, Dallin R. Swiss

Theses and Dissertations

This thesis investigates the potential benefits and challenges of using compliant mechanisms in the design of haptic interfaces. The benefits and challenges are presented with an emphasis on their inherent springback behavior and an active compensation approach. Design criteria for compliant mechanism joint candidates are reviewed and several joints are surveyed. Quantitative calculations of axial stiffness and maximum stress for five candidates are presented. Generalized analytical models of springback force and compensation torque are created to simulate the implementation of each joint candidate in a two degree-of-freedom planar pantograph. We use these models in the development and discussion of an …