Engineering Commons^™

Application Of Gis And Geographically Weighted Regression To Evaluate The Spatial Non‐Stationarity Relationships Between Precipitation Vs. Irrigated And Rainfed Maize And Soybean Yields, Vivek Sharma, Ayse Kilic, Isa Kabenge, Suat Irmak

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Understanding the relationship between the spatial distribution of precipitation and crop yields on large scales (i.e., county, state, regional) while accounting for the spatial non‐stationarity can help managers to better evaluate the long‐term trends in agricultural productivity to make better assessments in food security, policy decisions, resource assessments, land and water resources enhancement, and management decisions. A relatively new technique, geographically weighted regression (GWR), has the ability to account for spatial non‐stationarity with space. While its application is growing in other scientific disciplines (i.e., social sciences), the application of this new technique in agricultural settings has not been practiced. The …

Narrow Grass Hedge Control Of Nutrient Loads Following Variable Manure Applications, John E. Gilley, Lisa M. Durso, Roger Eigenberg, David B. Marx, Brian L. Woodbury

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The effectiveness of a narrow grass hedge in reducing runoff nutrient loads following manure application was examined in this study. Beef cattle manure was applied to 0.75 m wide by 4.0 m long plots established on an Aksarben silty clay loam located in southeast Nebraska. Manure was added at rates required to meet none or the 1, 2, or 4 year nitrogen requirements for corn. Runoff water quality was measured during three 30 min simulated rainfall events. Manure application rate significantly affected dissolved phosphorus (DP) and total phosphorus (TP) loads in runoff on the plots without a grass hedge. However, …

Characterization Of Potential Health Promoting Lipids In The Co-Products Of De-Flossed Milkweed, Vicki Schlegel, Richard Zbasnik, Tammy Gries, Bo Hyun Lee, Timothy Carr, Ji-Young Lee, Curtis Weller, Susan Cuppett

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The floss and oil of the common milkweed (Asclepias syriaca L.) seeds are currently used to produce comforters/pillows and skin care products, respectively. As an outcome of these products, copious quantities co-products (pressed seed meal and pod biomass) are disposed of each year despite the presence of potential health benefiting lipids. The objective of this project was to determine the feasibility of developing the lipid fraction from of these co-products for the fast growing dietary human health market. Although certain types of lipids were affected by the extraction solvent used (hexane and diethyl ether) as were overall amounts, analysis …

A 6-Degree Of Freedom Static Thrust Stand Developed For Rc-Scale Jet Engines, Spencer Sessions

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

The description of a portable 6-degree of freedom static thrust stand for RC-scale jet engines is reported. The stand includes three axial and three lateral load cells measuring static thrust with six degrees of freedom. A pitot probe with single axis position control placed perpendicular to exhaust flow measures stagnation pressure along the nozzle centerline. A pitot probe open to the inside of the engine nozzle normal to the exhaust flow and near the outlet measures static pressure. A digital scale measures fuel consumption. The engine is mounted with exhaust gases exiting upward avoiding ground effects and thrust acting downward. …

South Davis Sewer District Pump Station Hydraulic Capacity Evaluation, James W. Dixon

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

In 2010, South Davis Sewer District (SDSD) determined that possible hydraulic problems existed in their various pump stations operating within their treatment plants. A hydraulic analysis was conducted for the pump stations to diagnose the problems and provide possible alternative solutions. This analysis was conducted by using hydraulic minor loss equations to determine the amount of flow that the pumps were capable of producing and then comparing those results to the required demands in the plants. In cases where the flows were lower than needed, alternatives were designed to provide the required flows.

In the south plant the pumps were …

Heat Transfer Through A Rotating Ball Bearing At Low Angular Velocities, Sarah Isert

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Bearings are commonly used in mechanical systems when there are rotating parts in the system. For bearings that run at speeds above about 1000 revolutions per minute, such as those used in aircraft turbines, machining tools, and automotive engines, it is important to take into account the heat transfer through the bearing system due to friction. Heat transfer is generally not considered for applications where the bearing is rotating at low speeds, such as clocks and bicycles. However, for certain aerospace applications, such as precision instruments or wind turbines, the heat transfer through the bearing becomes relevant. The case where …

Remote Control And Automation Of The Crockett Canal Head Gates, Tyler Dean Richards

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

In order to improve the control of the Crockett canal an automated control system for the head gates was proposed and an analysis of design alternatives was conducted. Design alternatives were analyzed based on the criteria of reliability, operational improvement, cost and safety. After the analysis was completed recommendations as to which type of automation system to install were made. A comprehensive design of the recommended design is included. The automation of the head gates has been separated into two phases. Items to be included in phase one are: retrofit each of the existing head gates with a multi-turn gate …

Statistical Comparisons Of Watershed-Scale Response To Climate Change In Selected Basins Across The United States, John Risley, Hamid Moradkhani, Lauren Hay, Steve Markstrom

Civil and Environmental Engineering Faculty Publications and Presentations

In an earlier global climate-change study, air temperature and precipitation data for the entire twenty-first century simulated from five general circulation models were used as input to precalibrated watershed models for 14 selected basins across the United States. Simulated daily streamflow and energy output from the watershed models were used to compute a range of statistics. With a side-by-side comparison of the statistical analyses for the 14 basins, regional climatic and hydrologic trends over the twenty-first century could be qualitatively identified. Low-flow statistics (95% exceedance, 7-day mean annual minimum, and summer mean monthly streamflow) decreased for almost all basins. Annual …

Model-Based Stripmap Synthetic Aperture Radar Processing, Roger D. West

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Synthetic aperture radar (SAR) is a type of remote sensor that provides its own illumination and is capable of forming high resolution images of the reflectivity of a scene. The reflectivity of the scene that is measured is dependent on the choice of carrier frequency; different carrier frequencies will yield different images of the same scene.

There are different modes for SAR sensors; two common modes are spotlight mode and stripmap mode. Furthermore, SAR sensors can either be continuously transmitting a signal, or they can transmit a pulse at some pulse repetition frequency (PRF). The work in this dissertation is …

Characteristics Of Combustion Flame Sprayed Nickel Aluminum Using A Coanda Assisted Spray Manipulation Collar For Off-Normal Deposits, Reid S. Archibald

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A novel flame spray collar called the Coanda Assisted Spray Manipulation collar (CSM) has been tested for use on the Sulzer Metco 5P II combustion flame spray gun. A comparison study of the stock nozzle and the CSM has been performed by evaluating the porosity, surface roughness, microhardness, tensile strength and microscopy of normal and off-normal sprayed NiAl deposits. The use of the CSM collar resulted in the need to position the sprayed coupons closer to the gun, which in turn affected the particle impact energy and particle temperatures of the NiAl powder. For the CSM, porosities had a larger …

A Comparative Study Of Three Image Matching Algorithms: Sift, Surf, And Fast, Maridalia Guerrero Peña

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A new method for assessing the performance of popular image matching algorithms is presented. Specifically, the method assesses the type of images under which each of the algorithms reviewed herein perform to its maximum or highest efficiency. The efficiency is measured in terms of the number of matches founds by the algorithm and the number of type I and type II errors encountered when the algorithm is tested against a specific pair of images. Current comparative studies asses the performance of the algorithms based on the results obtained in different criteria such as speed, sensitivity, occlusion, and others. These studies …

Investigation Of The Design And Static Behavior Of Cylindrical Tubular Composite Adhesive Joints Utilizing The Finite Element Method And Stress-Based Failure Theories, Michael D. Lambert

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The stress and strength behavior of cylindrical tubular adhesive joints composed of dissimilar materials was explored. This was accomplished with the finite element method (FEM) and stress-based failure theories. Also, it was shown how a design of experiments (DOE) based method can be used to objectively organize the process of optimizing joint strength by using stress-based failure criteria.

The finite element program used in this work was written in-house from scratch to implement the FEM for the purpose of solving both axisymmetric and three-dimensional linear elastic governing equations of static equilibrium. The formulation of the three-dimensional model is presented, and …

Measuring The Removal Of Trichloroethylene From Phytoremediation Sites At Travis And Fairchild Air Force Bases, Heather A. Klein

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Past use of trichloroethylene (TCE) as a degreasing solvent for aircraft maintenance has resulted in widespread groundwater contamination at Air Force Bases around the world. Travis AFB in California and Fairchild AFB in Washington are evaluating phytoremediation as a treatment option, since trees have been reported to take up dissolved TCE from shallow groundwater and volatilize it to the atmosphere while enhancing the volatilization of TCE from surrounding soil. Previous studies generally focused on the identification of removal mechanisms. The emphasis of this research was to quantify total TCE removal from phytoremediation demonstration plots at Travis and Fairchild AFBs.

Tree …

Piano Key Weir Head Discharge Relationships, Ricky M. Anderson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A piano key (PK) weir is a type of nonlinear (labyrinth-type) weir developed specifically for free-surface flow control structures with relatively small spillway footprints. Currently, no generally accepted standard PK weir design procedure is available. This is due, in part, to the large number of geometric parameters and a limited understanding of their effects on discharge efficiency (discharge efficiency is quantified by the discharge coefficient of the standard weir equation). However, Hydrocoop, a non-profit French dam spillways association, has recommended a PK weir design and a head-discharge relationship specific to that geometry.

To develop a better understanding of the effects …

A Linearly And Circularly Polarized Active Integrated Antenna, Ali Khoshniat

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis work presents a new harmonic suppression technique for microstrip patch antennas. Harmonic suppression in active integrated antennas is known as an effective method to improve the efficiency of amplifiers in transmitter side. In the proposed design, the antenna works as the radiating element and, at the same time, as the tuning load for the amplifier circuit that is directly matched to the antenna. The proposed active antenna architecture is easy to fabricate and is symmetric, so it can be conveniently mass-produced and designed to have circular polarization, which is preferred in many applications such as satellite communications.

The …

Dynamic Testing For A Steel Truss Bridge For The Long Term Bridge Performance Program, Cody Joshua Santos

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Under the direction of the Federal Highway Administration the Long Term Bridge Performance Program (LTBP) selected Minnesota Bridge number 5718 as a pilot bridge for evaluation. This program focuses on the monitoring of bridges for a 20-year period to understand the structural behavior over time due to the various loads and weathering. In monitoring this bridge a better understanding can be acquired for the maintenance issues related to the nation's deteriorating bridge infrastructure.

Bridge Number 5718, which is located just outside of Sandstone Minnesota, is a steel truss bridge that spans the Kettle River. Constant monitoring of the bridge along …

Fluoro-Silane As A Functional Monomer For Protein Conformational Imprinting, Yun Peng

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

By using the technology of molecularly imprinted polymer (MIP), we propose to synthesize a protein conformational imprint that also acts as a plastic enzyme, inducing protein structural transitions. The imprint aims at MIP-induced stabilization and / or formation of bound protein secondary structure and the applications associated with analysis and correction of misfolded proteins. The screening of polymeric functional monomers being able to induce the conformational transitions in proteins is investigated in this report.

The fluoro-silanes (3-heptafluoroisopropoxy)propalethoxysilane (7F) and 3,3,3-trifluoropropylmethoxysilane (3F) were employed as functional monomers for synthesis of this catalytic protein conformational imprint via sol-gel reactions. 3F was demonstrated …

Surface Morphology Implications On Langmuir Probe Measurements, Padmashri Suresh

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Langmuir probes are extensively employed to study the plasmas in space and laboratory environments. Successful measurements require a comprehensive modeling of both the plasma environment and the probe conditions in the form of current collection models. In this thesis, the surface morphology implications on the probe current collection are investigated. This problem is applied and solved in the context of a CubeSat regime. The first problem that is investigated is the consequence of surface structural variability on the current measurements. A new model for dealing with non-uniformity of the probe surface structure is developed in this paper. This model is …

Evaluating Changes And Estimating Seasonal Precipitation For Colorado River Basin Using Stochastic Non-Parametric Disaggregation Technique, Ajay Kalra, Sajjad Ahmad

Civil and Environmental Engineering and Construction Faculty Research

Precipitation estimation is an important and challenging task in hydrology because of high variability and changing climate. This research involves (1) analyzing changes (trend and step) in seasonal precipitation and (2) estimating seasonal precipitation by disaggregating water year precipitation using a k-nearest neighbor (KNN) nonparametric technique for 29 climate divisions encompassing the Colorado River Basin. Water year precipitation data from 1900 to 2008 are subdivided into four seasons (i.e., autumn, winter, spring, and summer). Two statistical tests (Mann-Kendall and Spearman’s rho) are used to evaluate trend changes, and a rank sum test is used to identify the step change in …

Migration Models - Comparison Of Pvc, Pet And Pla Diffusivity, Combined With A Production Cost Model For Westridge Laboratories, Shelley Cooke, Sarina Surrette

Materials Engineering

This project has two parts: [1] a migration and diffusivity model for candidate plastics used in containers, and [2] a product cost model for Westridge Laboratories (Santa Ana, CA).

Diffusion modeling is a useful tool to predict migration of polymer constituents into exposed liquids.  Polyvinyl chloride (PVC), polyethylene terephthalate (PET) and polylactic acid (PLA) were studied to estimate production costs, and component migration into water-based liquids from plastic containers.  Bis (2-ethylhexyl) phthalate (DEHP), antimony trioxide, and stannous octoate, are components of concern in the three candidate polymers, respectively.  Normal detection limits for these constituents are about 1 - 10 ppb, …

Agent-Based Under Hood Packing, Karthik Ravindranath

All Theses

Improving vehicle performance and passenger comfort has been a prime engineering concern and focus of research for many years in automotive design. Turning to high-performance components in an effort to improve vehicle performance alone is often not enough and their placement and interactions with other components should also be an integral part of the improvement process. With the advancement in hybrid electric vehicle technology, the packing of components under the hood is ever more essential and challenging. Under hood packing is a multi-objective optimization problem with many, and mostly conflicting objectives. A non-deterministic multi-objective evolutionary algorithm needs to be integrated …

Evaluation Of Manganese Control In The Source Water And Microfiltration Plant Of A South Carolina Water Utility, Daniel Lewis

All Theses

Although present in most water supplies, manganese is a difficult-to-treat nuisance contaminant in drinking water. The US Environmental Protection Agency (EPA) has set a Secondary Maximum Contaminant Level (SMCL) of 0.05 mg/L but experts have recommended a goal of 0.02 mg/L or less to avoid chronic issues with the metal. This work is a report on manganese control for the Startex-Jackson-Wellford-Duncan (SJWD) Water District, a water utility in northwestern SC. Fourteen locations were sampled from June 2010 through October 2011. Manganese, iron, dissolved organic carbon, dissolved oxygen, and other relevant parameters were measured.
The lake-fed Middle Tyger River is the …

Improving Concrete Containment Structures Associated With Fixed Cone Valves, B. Skyler Buck, Michael C. Johnson, Zachary B. Sharp

Civil and Environmental Engineering Faculty Publications

Fixed-Cone valves are often used to dissipate energy and regulate flow at the low level outlet works of dams.Fixed-Cone valves, also known as Howell-Bunger valves, create an expanding conical jet allowing the energy of the water to dissipate over a large area. However, in many applications constructing the large stilling basin necessary for these valves is either not possible or not feasible. In order to reduce the relative size of the stilling basin, hoods or concrete containment structures have been used in conjunction with Fixed-Cone valves. This paper discusses the use of baffles in concrete containment structures in order to …

Estimating And Mitigating Radiated Emissions From Pcb Heatsinks, Xinbo He

All Dissertations

The advance of VLSI technology requires heatsinks to take away the heat generated by ICs and keep the temperature below an acceptable limit. These metal heatsinks radiate and cause EMI problems when electromagnetic noises are coupled to them. Thus it is important to study the possible radiation of a VLSI heatsink and the effective methods to reduce the radiated emissions.
This dissertation includes three chapters on estimating and mitigating VLSI heatsink radiation. In the first chapter, a closed-form expression is derived for determining the maximum possible radiated emissions from a heatsink over a printed circuit board or chassis plane as …

High Resolution Vision-Based Servomechanism Using A Dynamic Target With Application To Cnc Machines, Carlos Montes-Solano

All Dissertations

This dissertation introduces a novel three dimensional vision-based servomechanism with application to real time position control for manufacturing equipment, such as Computer Numerical Control (CNC) machine tools. The proposed system directly observes the multi-dimensional position of a point on the moving tool relative to a fixed ground, thus bypassing the inaccurate kinematic model normally used to convert axis sensor-readings into an estimate of the tool position.

A charge-coupled device (CCD camera) is used as the position transducer, which directly measures the current position error of the tool referenced to an absolute coordinate system. Due to the direct-sensing nature of the …

In-Wheel Coupled Suspenison And Drive System For Attitude Control And Vehicle Propulsion, Robert Clippard

All Dissertations

The automotive marketplace is a volatile and dynamic system driven by consumer desires, marketing, fuel prices, technology, and legislation. Recently many of these factors have culminated in a common effort to encourage hybrid and electric vehicle development. The technology for electric vehicles has finally found enough maturity to be implemented into consumer based vehicles from hybrid SUVs to high performance sports cars. This expansion in available propulsion systems and vehicle architectures has spurred research and development into new and novel approaches for propulsion as well as systems to provide increased ride comfort.
This work presents a dual electric motor drive …

Vertical Take-Off With Artificial Airflow, Rachel J. Adams

Undergraduate Honors Capstone Projects

Vertical take-off has been a capability available only to military aircraft due to the design utilized. However, if the design incorporated artificial airflow over the aircraft wings, then vertical take-off becomes a possibility for aircraft varying from general aviation to small jets. In order to determine the most efficient wing for vertical take-off, multiple airfoils with different characteristics and airflow configurations were designed and tested. For each airfoil, the coefficient of lift was to be calculated and recorded in order to determine which airfoil had the greatest capability for vertical take-off. However, the airfoil/airflow design utilized in the tests did …

An Empirical Study Of Student Programming Bugs, Amy Hansen

Undergraduate Honors Capstone Projects

Students in introductory computer science courses often have difficulty with coding and problem solving, which results in bugs. These bugs cause both student frustration and attrition of many of our CS majors. In this work, we seek to understand the bugs that students encounter. We have two sources of data. First, we collect and analyze 450 bugs that were brought to our tutor lab by our CS 1 and CS2 students. Second, we analyze bugs in CS I homework assignments. The results show that the majority of the problems are due to problem solving skills, while the remaining problems involve …

Analysis Of Effects Of Financial Factors On Profitability Of Low-Cost And Legacy Carriers, Nicholas Joseph Kleoppel

Doctoral Dissertations and Master's Theses

Since airline deregulation in 1978, there have been over 180 bankruptcy filings by airlines. Legacy and Low-Cost carriers are unique in how they operate and how they generate revenue; both business models have advantages and disadvantages. However, the Low-Cost carriers have shown increases in revenue and have been growing at increasing rates over the Legacy carriers. This study analyzed financial factors from four airlines in each business model to reveal which financial factors can help determine profitability of an airline. This researcher found significant differences between Legacy and Low-Cost Passenger Revenues, Maintenance Expenses, and Depreciation and Amortization Expenses. Additionally, there …

Aerodynamic Thrust Vectoring For Attitude Control Of A Vertically Thrusting Jet Engine, M. Ryan Schaefermeyer

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

NASA’s long range vision for space exploration includes human and robotic missions to extraterrestrial bodies including the moon, asteroids and the martian surface. All feasible extraterrestrial landing sites in the solar system are smaller and have gravitational fields of lesser strength than Earth’s gravity field. Thus, a need exists for evaluating autonomous and human-piloted landing techniques in these reduced-gravity situations. A small-scale, free-flying, reduced-gravity simulation vehicle was designed by a group of senior mechanical engineering students with the help of faculty and graduate student advisors at Utah State University during the 2009-2010 academic year. The design reproduces many of the …