Engineering Commons^™

Mp3 Player System Design, Eric Wu

Electrical Engineering

The purpose of this project is to design and build a portable audio player that reads music files off an SD card, decodes the music file and outputs the music through a headphone jack.  A microcontroller running FreeRTOS will facilitate the data transfer between an SD card and the decoding chip.  The decoded audio will then be sent to a high-end DAC chip that outputs the sound.

Wireless Sensor Network For Energy And Environmental Monitoring: Helping Old Buildings Go Green, Jacob Power

Electrical Engineering

Today, the rising cost of energy and social trend of “going green” has put increasing pressure on commercial property owners to improve the efficiency of their investments.  There is good reason for this, too.  In the State of California, office buildings represent the single largest user of energy in the commercial sector.  This project consisted of the design, implementation, construction, testing, and deployment of a wireless sensor network for energy and environmental monitoring in retrofit commercial office installations.  The analyzed data generated by this system can be used by building management and owners to identify areas of inefficiency within the …

Rfid Home And Office Automation System: Based On Localized Room Entry, Nolan Clark

Electrical Engineering

Design and build a proof of concept model demonstrating an application of Radio Frequency Identification (RFID) technology for use in a home or office lighting automation system. The system provides new means for reducing energy consumption through active light switching based on simplified location tracking. Often lighting systems use motion sensors and timers to determine when a person enters or leaves a room, but these platforms are based purely on motion meaning “no motion, no light.” The RFID based system utilizes medium range RFID readers and tags located at doorways or narrow passageways in the environment to provide a general …

Design Strategy For A 3-Phase Variable Frequency Drive (Vfd), Omar David Munoz

Electrical Engineering

This paper describes the design processes for a 3-Phase Variable Frequency Drive (VFD) as broken up into two stages: The AC-DC converter and the DC-AC converter. It acknowledges three (3) design versions, all. The output of the motor drive is 3-phase pulse width modulation (PWM) ranging in possible operation frequencies from 0Hz to 13kHz. The frequency control circuit uses an Arduino Uno based of the ATMEGA 328p.

The Canonical Decomposition Fuzzy Comparative Methodology For Assessing Architectures, Jason P. Dauby, Cihan H. Dagli

Engineering Management and Systems Engineering Faculty Research & Creative Works

The challenge for system architects is to perform a realistic assessment of an inherently ambiguous system concept. Many existing assessment methods are available, but these are often subjective and unrepeatable. Repeatability, objectivity, and increased fidelity are desired. an architecture assessment methodology capable of achieving these objectives is possible by drawing on the strengths of existing approaches while addressing their collective weaknesses. the proposed methodology is the Canonical Decomposition Fuzzy Comparative approach. the theoretical foundations of this methodology are developed herein and tested through the assessment of three physical architectures for a peer-to-peer wireless network. an extensible modeling framework is established …

Unlv Stars Unabridged Report, University Of Nevada, Las Vegas

Reports (USI)

University of Nevada, Las Vegas, by earning a 2011 Silver Rating in the Sustainability Tracking, Assessment & Ratings System (STARS), is ahead of the curve among public universities – and improving.

STARS is a voluntary, self–reporting framework developed by the Association for the Advancement of Sustainability in Higher Education (AASHE) to help measure sustainability performance over time and among colleges and universities nationwide. The UNLV Sustainability Council oversaw STARS, which by measuring sustainability can help UNLV to reduce energy consumption and waste, improve education, attract research, and generate jobs.

A rating of Silver puts UNLV in great company – with …

Building Balls: Final Design Report, Jumpsport Inc., Gary Johnson, Rosalie Mangione, Steven (Steve) Rose

Mechanical Engineering

JumpSport, a major trampoline company, has requested Cal Poly to design a custom play-structure consisting of large diameter balls with two types of connectors-long rod connections and very close connectors (for a ball-to-ball type connection).  By the end of the project, appropriate testing will be carried out on the connections and a full-scale model will be constructed.

After an extensive design process, our team of three decided on a rod connection style for both the long and short connectors.  These consist of a hook that latches into a loop protruding from the ball where the hook is attached by a …

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …

Rapid Animatronic Target System, Brandon Keith Bray, Matt Gerhardt Guise, Martin Thomas Quinn

Mechanical Engineering

No abstract provided.

Characterization Of The Relationship Between The Microstructure And Tensile Strength Of Annealed Ti-6al-4v, Aldo Corona

Materials Engineering

Tensile coupons of Ti-6Al-4V were heat treated at varying annealing temperatures from 1200°F (648°C) to 1450°F (787°C)  at 50°F  (23°C) increments for 1 hour. The samples were air cooled to room temperature or furnace cooled to 800°F (426°C) followed by air cooling to room temperature. Four tensile coupons were treated at each annealing temperature and cooling rate. Alpha case was observed to form on the surface of the samples post heat treatment with a maximum depth of 25 µm (.001 in). Samples were tensile tested for their ultimate tensile strength, yield strength, and percent elongation.  Samples across all annealing temperatures …

The Effects Of Colorant Oxides And Firing Rate On The Nucleation And Growth Of Zinc Silicate Crystals In Crystalline Glazes, Nicolas Coffey

Materials Engineering

This study looked at the effects of colorant oxides and firing rate on the nucleation and growth of crystals in zinc-based crystalline glazes. One weight percent of iron and copper oxide powders were mixed separately with a zinc-based crystalline glaze. The uncolored glaze along with both colored glazes were applied to test tiles and fired. Two different firing schedules were used with different ramp up firing rates of 165°C/hr (slow) and 205°C/hr (fast). X-ray diffraction (XRD) analysis found both zinc oxide and silica oxide in the raw glaze, which are the main components in the formation of zinc silicate. XRD …

Processing Pdms Gecko Tape Using Isopore Filters And Silicon Wafer Templates, Boris Luu

Materials Engineering

Gecko tape was processed through nanomolding involving two types of templates. One template was a Millapore Isopore polycarbonate membrane filter and the other template was an n-type silicon wafer processed to include four different pore diameters. These pore diameters were 20, 40, 80, and 160 microns. AutoCAD was used to design to a mask to be used later during photolithography. Two n-type wafers were sputtered with aluminum, underwent photolithography, and then etched using reactive ion etching. A template was placed into a Petri dish and Sylgard 184 polydimethylsiloxane (PDMS) was poured on the template. Once the PDMS cured,   the 1 …

Oxidation Kinetics Of Silver Thin Films For Antimicrobial Applications In The Health Care Industry, Sean D. Morham

Materials Engineering

To determine if varying city water qualities from around the United States can support a developing “oxidation corrosion of silver thin films” method of creating aqueous ionic silver solutions for the anti-microbial treatment of healthcare linens, a test was devised holding all variables constant with the exception of water quality parameters. This corrosion style test was done in order to assess a pass/fail criteria of 25 ppb ionic silver concentration in the aqueous solutions which resulted from the corrosion of silver thin film coated substrates. Above 25 ppb being a pass, below 25 ppb being a fail. While varying the …

Investigating The Mechanical Properties Of Compression Molded Carbon Fiber Reinforced Sheet Molding Compound, Bradley A. Jones

Materials Engineering

Callaway Golf receives a proprietary blend of prepreg material from Quantum Composites. Callaway processes the prepreg in-house and supplied 254mm x 254mm x 1.3mm panels of carbon fiber sheet molding compound (CFSMC) for characterizing. Tensile strength was analyzed by conducting tensile tests per ASTM D3039. Tensile coupons were cut to 254mm long by 25.4mm wide. Tabs were constructed from 1.6mm thick GFRP printed circuit board material. A commercial grade two part epoxy was used to bond the tabs to the CFSMC. Tensile results were inconclusive due to consistent fractures occurring outside the gauge lengths of the specimens.

Flexure strength was …

Improving Cal Poly Space Systems Infrastructure, Tyler Richier

Industrial and Manufacturing Engineering

The goal of this project was to increase the usable space for the club Cal Poly Space Systems to work on its projects, improve the safety for its members, and reduce the time it takes to manufacture its products. The project demonstrated the effectiveness of 5S in improving a workspace. Club members were measurably more comfortable in the work environment and spent less time looking for tools. Current rooms were made more professional by ridding the workplace of non-valued items and finding sensible locations for high-traffic items. Additional rooms were added and they should indisputably support club projects the upcoming …

5s Implementation Plan For The Shipping Department At Helical Products Co., Eric William Walker

Industrial and Manufacturing Engineering

Helical Products Company is a business that manufactures flexure products, such as couplings and u-joints. As part of a movement towards lean manufacturing, Helical Products Company of Santa Maria, California is in need of a principle that will help them continuously improve their shipping department. A study of 5S, a lean principle focused on waste reduction, will be done to investigate opportunity for implementation. A literature review takes a peek on research of lean manufacturing history, lean workbook/ tutorials and lastly case studies and journal articles. The output of research provides a design plan for Helical using 5S and other …

Ackermann Steering Geometry Applied To A Skateboard Truck, Daniel D. Downs

Industrial and Manufacturing Engineering

Conventional skateboard trucks are currently unable to meet the challenges of the modern enthusiast. They are lacking in key performance metrics such as handling, stability, and traction. Longboard enthusiasts, whom rely heavily on handling performance, are hungry for new and innovative technology to help bring the sport to the next level. The aim of this project was to solve these problems by applying specific aspects of automotive steering geometry and best engineering practices. Three successive prototypes were designed, with the first two prototype sets being manufactured and extensively tested. The first prototype served as a proof of concept, but suffered …

Cardiac Staging Facility Workflow Redesign, Ryan Chang

Industrial and Manufacturing Engineering

This study analyzes and proposes Cardiac Staging nurse workflow improvements along with a new Cardiac Staging facility design at French Hospital. Currently, patients spend an expected 125 minutes in Cardiac Staging. It was found that 60% of the time in Cardiac Staging was spent waiting to be transferred into the Cath Lab. The following Industrial Engineering methods were utilized to eliminate waste in staging and design a new staging area:

 Use of Lean and Six-Sigma tools to recommend new patient arrival time

 Manufacturing product scheduling to reduce patient wait time

 Use of facility redesign techniques to improve …

Chinese To English Introductory Cover Letter Generator, Jason L. Stine

Liberal Arts and Engineering Studies

The Chinese to English Introductory Cover Letter Generator allows Chinese computer users who know little to no English automatically generate a self-introductory cover letter in good English. As an example, professors in English-speaking countries are increasingly receiving emails from students abroad in countries like China, and these students often need to introduce themselves in order to support their reasons for their message. Unfortunately, more often than not these letters contain poorly written English. This software aims to help solve this issue. Using a combination of a “sentence template” system and intelligent natural language processing software, the program assembles each paragraph …

Groundwater Research In Middle Earth, Thomas Lapoint

Liberal Arts and Engineering Studies

My senior project focused on studying saltwater intrusion in a coastal town of New Zealand. I feel lucky that I was able to travel to such a distant place, conduct research that was insightful and interesting, and immerse myself in an international culture all in the name of my education. As a Liberal Arts and Engineering Studies student, I aim to analyze not only the cultural differences and similarities that the foreign environment offers to me but also the detailed, technical, engineering aspect of my research. I believe that my education should be approached with a well rounded perspective that …

Design And Implementation Of A Byzantine Fault Tolerance Framework For Non-Deterministic Applications, H. Zhang, Wenbing Zhao, Louise E. Moser, P. Michael Melliar-Smith

Electrical and Computer Engineering Faculty Publications

State-machine-based replication is an effective way to increase the availability and dependability of mission-critical applications. However, all practical applications contain some degree of non-determinism. Consequently, ensuring strong replica consistency in the presence of application non-determinism has been one of the biggest challenges in building dependable distributed systems. In this Study, the authors propose a classification of common types of application non-determinism with respect to the requirement of achieving Byzantine fault tolerance (BFT), and present the design and implementation of a BFT framework that controls these types of non-determinism in a systematic manner.

Fuzzy Robot Controller Tuning With Biogeography-Based Optimization, George Thomas, Paul Lozovyy, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

Biogeography-based optimization (BBO) is an evolutionary algorithm (EA) based upon the models of biogeography, which describe the relationship between habitat suitability and the migration of species across habitats. In this work, we apply BBO to the problem of tuning the fuzzy tracking controller of mobile robots. This is an extension of previous work, in which we used BBO to tune a proportional-derivative (PD) controller for these robots. We show that BBO can successfully tune the shape of membership functions for a fuzzy controller with both simulation and real world experimental results.

Distributed Learning With Biogeography-Based Optimization, Carre Scheidegger, Arpit Shah, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

We present hardware testing of an evolutionary algorithm known as biogeography-based optimization (BBO) and extend it to distributed learning. BBO is an evolutionary algorithm based on the theory of biogeography, which describes how nature geographically distributes organisms. We introduce a new BBO algorithm that does not use a centralized computer, and which we call distributed BBO. BBO and distributed BBO have been developed by mimicking nature to obtain an algorithm that optimizes solutions for different situations and problems. We use fourteen common benchmark functions to obtain results from BBO and distributed BBO, and we also use both algorithms to optimize …

Value Landscape Engineering: Identifying Costs, Water Use, Labor, And Impacts To Support Landscape Choice., Kelly Kopp, Larry Rupp, Paul G. Johnson, Roger K. Kjelgren, David E. Rosenberg, Heidi Kratsch

CWEL Publications

We present a spreadsheet model that identifies the costs, water, labor, fertilizer, pesticides, fuel, energy, carbon emissions, and particulates required of and generated by a user-specified residential or commercial landscape over its economic life. This life includes site preparation, materials purchase, installation, annual maintenance and replacing landscape features that wear out or die. Users provide a variety of site-descriptive information and the model queries an extensive database of landscape data to calculate costs, required inputs, and impacts. We verified model results against observations of water, labor, fertilizer, and fuel use over eight years at three landscapes in the Salt Lake …

Looking Below The Surface Of Breast Tissue During Surgery, A Mahadevan-Jansen, Md Keller, Elizabeth Vargis, B Caldwell, T-Q Nguyen, Ndm Granja, M Sanders, Mc Kelley

Biological Engineering Faculty Publications

In this article, we present a method that provides prompt detection of the presence of cancer cells inside the 2-mm margin of tissue surrounding the tumor after excision using spatially offset Raman spectroscopy (SORS). SORS was developed to detect subtle changes in soft tissue spectra in the 100–2000 μm range and tested on excised breast tissues. The results display a very high specificity and sensitivity (100% and 95%, respectively) of classification between positive and negative tumor margins. SORS is a clinically feasible method, suitable for the real-time, intraoperative assessment of tumor margins at the micrometer level.

On The Relative Sensitivity Of Mass-Sensitive Chemical Microsensors, Luke A. Beardslee, S. Truax, J.-J. Su, Stephen M. Heinrich, Fabien Josse Phd, O. Brand

Civil and Environmental Engineering Faculty Research and Publications

In this work, the chemical sensitivity of mass-sensitive chemical microsensors with a uniform layer sandwich structure vibrating in their lateral or in-plane flexural modes is investigated. It is experimentally verified that the relative chemical sensitivity of such resonant microsensors is -to a first order- independent of the microstructure's in-plane dimensions and the flexural eigenmode used, and only depends on the layer thicknesses and densities as well as the sorption properties of the sensing film. Important implications for the design of mass-sensitive chemical microsensors are discussed, whereby the designer can focus on the layer stack to optimize the chemical sensitivity and …

An Analysis Of The Effectiveness Of Emergency Locator Transmitters To Reduce Response Time And Locate Wreckage In U.S. General Aviation Accidents, Ajit Jesudoss

Doctoral Dissertations and Master's Theses

Emergency Locator Transmitters (ELT) help search crews to locate aircraft in distress and to rescue survivors. This study analyzed ELT data from U.S. General Aviation accidents during the period 2006 to 2010. This study examined the effectiveness of ELTs in terms of ELT Success Rate (ESR) and False Negative Rate (FNR) based on ELT-Aided. This study found a significant difference between ELT-Operated and ELT-Aided. The ESR was found to be 38.58% whereas the FNR was found to be 61.42 %. The Missing Data Ratio (MDR), where accident reports had no ELT information, was found to be above 95%. Recommendations were …

Seawater/Wastewater Production Of Microalgae-Based Biofuels In Closed Loop Tubular Photobioreactors, Joshua Bradley Lowrey

Master's Theses

The push for alternatives to petroleum fuels has forced researchers to look for highly productive, renewable, non-food resources.  The advantages of using microalgae instead of traditional oil crops for biofuel production include high oil yields, rapid reproductive rates, and versatile growing requirements.  In order to reduce the cost of producing microalgae based biofuels, wastewater has been used as a nutrient source instead of specialized plant nutrients.  The purpose of this study was to compare the relative effectiveness of different combinations of microalgae strain and dairy wastewater for increasing biomass.  The methods for monitoring growth included optical density, cell counting, biomass …

Assessment Of First Year Experiences At Sjsu, Patricia Backer, Emily Allen, Janet Sundrud

Faculty Publications

With nearly 5,000 students, the Charles W. Davidson College of Engineering (CoE) at San José State University (SJSU) is the largest provider of engineers to Silicon Valley companies and is ranked 12th among engineering programs for master’s-level institutions in the 2009 U.S. News &World Report's listing of "America’s Best Colleges. “Our overarching theoretical model for student retention is based on Tinto’s model. We adapted this model, based on additional research, to address the needs of students at SJSU. According to this model, effective and positive interactions in college should increase the student’s commitment and effort in college, and thereby, increase …

Service Learning In A Multi-Disciplinary Renewable Energy Engineering Course, Stacy Gleixner, Patricia Backer, Elena Klaw

Faculty Publications

One of the most significant challenges facing this coming generation of engineers is how to fight the complex issue of climate change. One aspect of this that is playing an increasingly important role is alternative and renewable energy technologies. Emerging applications such as solar cells, wind energy conversion devices, and fuel cells involve significant contributions across a range of traditional engineering disciplines. Therefore, for companies to be successful in researching, designing, and manufacturing these products, they must operate in a truly multi-disciplinary environment. To prepare graduates to be successful in this, engineering education must provide students with multi-disciplinary learning environments. …