Engineering Commons^™

Evaluation Of A Virtual Refrigerant Charge Sensor, Woohyun Kim, James E. Braun, Haorong Li

Durham School of Architectural Engineering and Construction: Faculty Publications

This paper presents a thorough evaluation of a method for determining refrigerant charge that employs low-cost, non-invasive measurements (i.e., surface mounted temperature measurements). The method could be used as part of a protocol for verified service providers (VSPs) in AC diagnostic tune-up or refrigerant charge, air flow (RCA) verification programs. Ultimately, the method could be embedded within a portable virtual refrigerant charge gauge for a technician’s use or permanently installed on the AC unit. The accuracy of the virtual refrigerant charge sensor method is evaluated in this paper using laboratory data for a number of different systems and over a …

Polaron And Phonon Properties In Proton Intercalated Amorphous Tungsten Oxide Thin Films, M. Saenger, T. Hoing, Brian W. Robertson, R. Billa, Tino Hofmann, Eva Schubert, Mathias Schubert

Nebraska Center for Materials and Nanoscience: Faculty Publications

We report on the evolution of the polaron and phonon mode properties in amorphous tungsten oxide thin films measured by spectroscopic ellipsometry in the infrared to ultraviolet spectral regions as a function of the intercalated proton density. A parametric physical model dielectric function is presented, which excellently describes the ellipsometry data over a large intercalated charge-density range. Upon increased amounts of intercalated charge we observe a strong increase in the polaron absorption in the visible spectral range, a decrease in the infrared W–O bond polarity, and an increase in the W=O bond polarity. Our findings support the oxygen-extraction model as …

Geometrical Interpretation And Simulation Of Holz Patterns, Xingzhong Li

Nebraska Center for Materials and Nanoscience: Faculty Publications

Higher-order Laue zone (HOLZ) pattern is very useful in measurement of crystalline lattice parameters, strain and composition variation in a small area of sample. Bloch dynamical theory on convergent-beam electron diffraction (CBED), including the formation of HOLZ lines, has been well developed and documented in Ref. and references therein. Although CBED patterns and included HOLZ lines are best modeled using a dynamical formulation, models based on a geometrical interpretation for the HOLZ-line positions have remained in widespread use because of their simplicity. Moreover, the geometrical interpretation is helpful to understand the formation of HOLZ lines for beginners. The geometrical interpretation …

Continuous Reservoir Model Updating By Ensemble Kalman Filter On Grid Computing Architectures, Xin Li

LSU Doctoral Dissertations

A reservoir engineering Grid computing toolkit, ResGrid and its extensions, were developed and applied to designed reservoir simulation studies and continuous reservoir model updating. The toolkit provides reservoir engineers with high performance computing capacity to complete their projects without requiring them to delve into Grid resource heterogeneity, security certification, or network protocols.

Continuous and real-time reservoir model updating is an important component of closed-loop model-based reservoir management. The method must rapidly and continuously update reservoir models by assimilating production data, so that the performance predictions and the associated uncertainty are up-to-date for optimization. The ensemble Kalman filter (EnKF), a Bayesian …

Bayesian Model Averaging On Hydraulic Conductivity Estimation And Groundwater Head Prediction, Xiaobao Li

LSU Doctoral Dissertations

Characterization of aquifer heterogeneity is inherently difficult because of the insufficiency of data, the inflexibility of parameterization methods, and non-uniqueness of parameterization methods. Groundwater predictions are greatly affected by multiple interpretations of aquifer properties and the uncertainties of model parameters. This study introduces a Bayesian model averaging (BMA) method along with multiple generalized parameterization (GP) methods to identify hydraulic conductivity and along with multiple simulation models to predict groundwater head and quantify the prediction uncertainty. Two major issues about BMA are discussed. The first problem is with using Occam’s window in usual BMA applications. Occam’s window only accepts models in …

Replication Of Metal-Based Microscale Structures By Compression Molding: A Combined Experimental And Finite Element Analysis Study, Jing Jiang

LSU Doctoral Dissertations

Fabrication of microscale Ta mold inserts by micro-electrical-discharge-machining (ìEDM) is reported. Morphology, chemistry, and structure of the near-surface region of as-machined Ta blanks have been characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy. A TaC surface layer forms on as-machined Ta surfaces. This altered surface layer was removed by electro-chemical-polishing. Further modification of Ta insert surfaces was accomplished by deposition of a conformal Ti-containing hydrogenated carbon coating. We demonstrate successful replication of high-aspect-ratio microscale structures (HARMS) in Al and Cu by compression molding with such surface-engineered Ta mold inserts. In addition, a hybrid microfabrication technique, combining …

Kilovolt Blumlein Pulse Generator With Variable Pulse Duration And Polarity, Andrea De Angelis, Juergen F. Kolb, Luigi Zeni, Karl H. Schoenbach

Bioelectrics Publications

A Blumlein pulse generator which utilizes the superposition of electrical pulses launched from two individually switched pulse forming lines has been designed and tested. By using a power metal-oxide-semiconductor field-effect transistor as a switch on each end of the Blumlein line, we were able to generate pulses with amplitudes of 1kV across a 100Ω load. Pulse duration and polarity can be controlled by the temporal delay in the triggering of the two switches. Using this technique, we have demonstrated the generation of pulses with durations between 8 and 60ns. The lower limit in pulse duration was determined by the switch …

Fabrication And Characterization Of Zno Nanowire Arrays With An Investigation Into Electrochemical Sensing Capabilities, Jessica Weber, Sathyaharish Jeedigunta, Ashok Kumar

Mechanical Engineering Faculty Publications

ZnO nanowire arrays were grown on a Si (100) substrate using the vapor-liquid-solid (VLS) method. ZnO nanowires were characterized by XRD, SEM, bright field TEM, and EDS. They were found to have a preferential orientation along the -axis. The as-prepared sample was functionalized with glucose oxidase by physical adsorption. FTIR was taken before and after functionalization to verify the presence of the attached enzyme. Electrochemical measurements were performed on the nanowire array by differential pulse voltammetry in the range of -0.6 to 0.4 V. The nanoarray sensor displayed high sensitivity to glucose in the range of 1.0 x 10^{-4 …}

Formation Control Of Car-Like Mobile Robots, Shweta Annapurani Panimadai Ramaswamy

Masters Theses

"A traditional tracking and control design approach already available in literature is derived and discussed for a car-like mobile robot. It involves a decoupled design involving two separate algorithms, one for velocity control design and another for torque control design. Weak interactions among the algorithms and separate designs make the robot performance optimization and the formation stability difficult to achieve. So, a new tracking and control architecture wherein the conventional elements are replaced by a single component that performs all the functions and hence called the integrated tracking and control scheme is used"--Abstract, page iii.

Application Of Artificial Neural Networks And Colored Petri Nets On Earthquake Resilient Water Distribution Systems, Nandini Kavanal Balakrishnan

Masters Theses

"Water distribution systems are important lifelines and a critical and complex infrastructure of a country. The performance of this system during unexpected rare events is important as it is one of the lifelines that people directly depend on and other factors indirectly impact the economy of a nation. In this thesis a couple of methods that can be used to predict damage and simulate the restoration process of a water distribution system are presented. Contributing to the effort of applying computational tools to infrastructure systems, Artificial Neural Network (ANN) is used to predict the rate of damage in the pipe …

Massive Spatiotemporal Watershed Hydrological Storm Event Response Model (Mhserm) With Time-Lapsed Nexrad Radar Feed, Changqing Song

Civil & Environmental Engineering Theses & Dissertations

Correctly and efficiently estimating hydrological responses corresponding to a specific storm event at the streams in a watershed is the main goal of any sound water resource management strategy. Methods for calculating a stream flow hydrograph at the selected streams typically require a great deal of spatial and temporal watershed data such as geomorphological data, soil survey, landcover, precipitation data, and stream network information to name a few. However, extracting and preprocessing such data for estimation and analysis is a hugely time-consuming task, especially for a watershed with hundreds of streams and lakes and complicated landcover and soil characteristics. To …

Nonlinear Random Response Of Large-Scale Sparse Finite Element Plate Bending Problems, Swati Chokshi

Civil & Environmental Engineering Theses & Dissertations

Acoustic fatigue is one of the major design considerations for skin panels exposed to high levels of random pressure at subsonic/supersonic/hypersonic speeds. The nonlinear large deflection random response of the single-bay panels aerospace structures subjected to random excitations at various sound pressure levels (SPLs) is investigated. The nonlinear responses of plate analyses are limited to determine the root-mean-square displacement under uniformly distributed pressure random loads. Efficient computational technologies like sparse storage schemes and parallel computation are proposed and incorporated to solve large-scale, nonlinear large deflection random vibration problems for both types of loading cases: (1) synchronized in time and (2) …

Rapid Prototyping For Virtual Environments, Emre Baydogan

Electrical & Computer Engineering Theses & Dissertations

Development of Virtual Environment (VE) applications is challenging where application developers are required to have expertise in the target VE technologies along with the problem domain expertise. New VE technologies impose a significant learning curve to even the most experienced VE developer. The proposed solution relies on synthesis to automate the migration of a VE application to a new unfamiliar VE platform/technology. To solve the problem, the Common Scene Definition Framework (CSDF) is developed, that serves as a superset/model representation of the target virtual world. Input modules are developed to populate the framework with the capabilities of the virtual world …

Design Of A High-Speed Architecture For Stabilization Of Video Captured Under Non-Uniform Lighting Conditions, Ming Zhu Zhang

Electrical & Computer Engineering Theses & Dissertations

Video captured in shaky conditions may lead to vibrations. A robust algorithm to immobilize the video by compensating for the vibrations from physical settings of the camera is presented in this dissertation. A very high performance hardware architecture on Field Programmable Gate Array (FPGA) technology is also developed for the implementation of the stabilization system. Stabilization of video sequences captured under non-uniform lighting conditions begins with a nonlinear enhancement process. This improves the visibility of the scene captured from physical sensing devices which have limited dynamic range. This physical limitation causes the saturated region of the image to shadow out …

Sublethal And Killing Effects Of Atmospheric-Pressure, Nonthermal Plasma On Eukaryotic Microalgae In Aqueous Media, Ying Zhong Tang, Xin Pei Lu, Mounir Laroussi, Fred C. Dobbs

OES Faculty Publications

In-depth studies on the interaction of nonthermal plasmas with microorganisms usually focus on bacteria; only little attention has been given to their effects on more complex eukaryotic cells. We report here nonthermal plasma's effects on cell motility, viability staining, and morphology of eukaryotic microalgae, with three marine dinoflagellates and a marine diatom as major targets. The effects on motility and viability staining depended on the time of exposure to plasma and the species of microalgae. We observed a strong pH decrease in aqueous samples (marine and freshwater algal cultures, their culture media, and deionized water) after exposure to plasma, and …

Characterization And Glass Formation Of Jsc-1 Lunar And Martian Soil Simulants, C. S. Ray, Sabhayu Sen, Signo Tadeu Dos Reis

Materials Science and Engineering Faculty Research & Creative Works

The space exploration mission of NASA requires human and robotic presence for long duration beyond the low earth orbit (LEO), especially on Moon and Mars. Developing a human habitat or colony on these planets would require a diverse range of materials, whose applications would range from structural foundations, (human) life support, (electric) power generation to components for scientific instrumentations. A reasonable and cost-effective approach for fabricating the materials needed for establishing a self-sufficient human outpost would be to primarily use local (in situ) resources on these planets. Since ancient times, glass and ceramics have been playing a vital role on …

A Learner-Centered Approach For Preparing At-Risk Students, Glenn Ellis, Mary Moriarty, Gary Felder

Engineering: Faculty Publications

No abstract provided.

Moving Up The Cmmi Capability And Maturity Levels Using Simulation, David Raffo, Wayne Wakeland

Complex Systems Faculty Publications and Presentations

Process Simulation Modeling (PSIM) can be used to evaluate issues related to process strategy, process improvement, technology and tool adoption, project management and control, and process design. It is a flexible tool and can aid in quantitatively testing ideas about how to configure a process or how to configure a software acquisition supply chain (consisting of contractors and sub-contractors) that would be too expensive or too risky to construct and evaluate in any other manner.

Recent developments in PSIM tools have drastically cut the costs of developing models to evaluate process issues. Moreover, new models and more systematic and repeatable …

Acceptor Levels In Gase:In Crystals Investigated By Deep-Level Transient Spectroscopy And Photoluminescence, Y. Cui, R. Dupere, A. Burger, D. Johnstone, K. C. Mandal, S. A. Payne

Faculty Publications

No abstract provided.

The Journal Of Undergraduate Research: Volume 06

The Journal of Undergraduate Research

This is the complete issue of the South Dakota State University Journal of Undergraduate Research, Volume 6.

Erosion Function Apparatus, Ryan Larsen

The Journal of Undergraduate Research

The Erosion Function Apparatus (EFA) test uses site-specific soil samples acquired via thin-walled tubes to generate the erosion rate and shear stress which is plotted to create an erosion plot. The information produced by the test can help an engineer accurately determine the depth of scour as a function of time for bridge design, and thereby determine the depth a foundation system should be constructed. During EFA testing, a data acquisition system records the velocity and amount of soil eroded. This data is used to calculate the Reynolds Number, friction factor, erosion rate, and shear stress. Once the data has …

Fatigue Analysis Of An Inline Skate Axel, Garrett Hansen, Mike Woizeschke

The Journal of Undergraduate Research

In this paper, an inline skate axel is analyzed based on fatigue and economic principles for four different materials. The loading scenario on the axel of the inline skate is derived and broken down to a maximum shear stress that must be less than the maximum fatigue stress of the axel material. A fatigue analysis using Goodman line diagrams is applied to axels made of aluminum, titanium, nylon, and PVC. The material strengths are then compared to the loading requirements and determined whether they would be sufficient for an axel material. Finally, the prices are compared to verify the selection …

Particle Motion On A Plane Slope Under Spilling Breaking Waves, Jennifer Nelson

The Journal of Undergraduate Research

The experiments discussed in this paper involve the motion of discrete solid particles on a plane slope under spilling breaking wave conditions. Particle Image Velocimetry was used to capture images of seeder particles in water so the motion of the fluid particles and solid particles could be traced. The images produced from the experiments have two phases. Since the behavior of the water and the sediment particles must be studied individually, the two phases of the image must be separated. A series of functions in MATLAB allows the two-phase image to be separated into two images—one containing only the sediment …

A Highly Reliable Non-Volatile File System For Small Satellites, Rama Krishna Nimmagadda

University of Kentucky Master's Theses

Recent Advancements in Solid State Memories have resulted in packing several Giga Bytes (GB) of memory into tiny postage stamp size Memory Cards. Of late, Secure Digital (SD) cards have become a de-facto standard for all portable handheld devices. They have found growing presence in almost all embedded applications, where huge volumes of data need to be handled and stored.

For the very same reason SD cards are being widely used in space applications also. Using these SD Cards in space applications requires robust radiation hardened SD cards and Highly Reliable Fault Tolerant File Systems to handle them. The present …

Color Multiplexed Single Pattern Sli, Neelima Mandava

University of Kentucky Master's Theses

Structured light pattern projection techniques are well known methods of accurately capturing 3-Dimensional information of the target surface. Traditional structured light methods require several different patterns to recover the depth, without ambiguity or albedo sensitivity, and are corrupted by object movement during the projection/capture process. This thesis work presents and discusses a color multiplexed structured light technique for recovering object shape from a single image thus being insensitive to object motion.

This method uses single pattern whose RGB channels are each encoded with a unique subpattern. The pattern is projected on to the target and the reflected image is captured …

Motion Correction Structured Light Using Pattern Interleaving Technique, Raja Kalyan Ram Cavaturu

University of Kentucky Master's Theses

Phase Measuring Profilometry (PMP) is the most robust scanning technique for static 3D data acquisition. To make this technique robust to the target objects which are in motion during the scan interval a novel algorithm called ‘Pattern Interleaving’ is used to get a high density single scan image and making Phase Measuring Profilometry insensitive to ‘z’ motion and prevent motion banding which is predominant in 3D reconstruction when the object is in motion during the scan time

Electrical, Structural, And Chemical Properties Of Semiconducting Metal Oxide Nanofiber Yarns, A. F. Lotus, E. T. Bender, E. A. Evans, R. D. Ramsier, Darrell Hyson Reneker

College of Polymer Science and Polymer Engineering

The electrical, structural, and chemical properties of twisted yarns of metal-oxide nanofibers, fabricated using a modified electrospinning technique, are investigated in this report. In particular, synthesized zinc oxide and nickel oxide yarns having diameters in the range of 4-40 mu m and lengths up to 10 cm were characterized, whose constituent nanofibers had average diameters of 60-100 nm. These yarns have one macroscopic dimension for handling while retaining some of the properties of nanofibers. (C) 2008 American Institute of Physics.

High Ppeed Circuit Techniques For Network Intrusion Detection Systems (Nids), Ajay Mohan Mahajan

Mechanical Engineering Faculty Research

No abstract provided.

Development Of Ballistic Limit Equations For Dual-Wall Spacecraft Shielding: A Concise History And Suggestions For Future Development, William P. Schonberg

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

All earth-orbiting spacecraft are susceptible to impacts by orbital debris particles, which can occur at extremely high speeds and can damage flight- and mission-critical systems. The traditional damage mitigating shield design for this threat consists of a “bumper” that is placed at a relatively small distance away from the main “inner wall” of the spacecraft. The performance of a hypervelocity impact shield is typically characterized by its ballistic limit equation, which is typically drawn as a line of demarcation between regions of rear-wall perforation and no perforation; when graphically represented, it is often referred to as a ballistic limit curve. …

Sustainable Lunar Habitat Protection Against Damage By Meteoroid Impacts, William P. Schonberg, Robin Putzar, Frank Schaefer

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Sustainability is a key consideration in the design and establishment of human habitats on the Moon (and on Mars as well). One hazard faced by such habitats is the damage that can be caused by the impact of a meteoroid on a critical habitat structure or structural component. in this paper we discuss various approaches to meteoroid shielding for lunar habitats, focusing on approaches that use resources mined or extracted from the moon. Advantages and disadvantages of these various techniques are also presented and discussed. the Moon's mineralogy is highlighted, and suggestions are presented for materials that can be used …