Engineering Commons^™

Generic Algorithms And Null Convention Logic Hardware Implementation For Unsigned And Signed Quad-Rail Multiplication, Samarsen Reddy Mallepalli

Masters Theses

"This thesis focuses on designing generic quad-rail arithmetic circuits, such as signed and unsigned multipliers and Multiply and Accumulate (MAC) units, using the asynchronous delay-insensitive NULL Convention Logic (NCL) paradigm. This work helps to build a library of reusable components to be used for automated NCL circuit synthesis, which will aid in the integration of asynchronous design paradigms into the semiconductor industry"--Abstract, page iii.

Modular Architecting For Effects Based Operations, Emel Meteoglu

Masters Theses

"Effects Based Operations (EBO) is a way of thinking for planning, executing and assessing any operations for the effects they produce, rather than dealing with actions, targets or even objectives. The literature on EBO has been growing day by day; however, there is still a need for modeling techniques and tools that provide more efficient and effective effects based assessment, planning and analysis in order to further develop the capabilities of the operations. In this context, this thesis presents an introduction to EBO by focusing on its methodology, its challenges and also its applicability in different systems. Moreover, this thesis …

Delay-Insensitive Ternary Logic (Ditl), Ravi Sankar Parameswaran Nair

Masters Theses

"This thesis focuses on development of a Single Rail Ternary Voltage Delay-Insensitive paradigm called Delay-Insensitive Ternary Logic (DITL), which is based on NULL Convention Logic (NCL). Single rail asynchronous logic has potential advantages over Dual-Rail logic such as reduction of Power and Interconnect as well as Logic Area. The DITL concept is developed in steps of individual circuit components. These components are designed at the transistor level and are connected together to form a registered pipeline system. Some variations in pipeline design are also investigated"--Abstract, page iii.

Optimal Formation Of Supplier Networks For Product Design And Production Phases To Realize An Evolving Product Family, Padmavathi K. Pakala

Masters Theses

"Due to rapid changes in customer requirements and vast improvements in technology, many product development companies have identified strategies like time-to-market (TTM) compression and product family development as critical for attaining success in today's hyper-competitive markets. Compressing the TTM, to a large extent, is dependent on the suppliers and the project execution skills of the integrator companies. This study presents a methodology for selecting suppliers for two significant phases of the product realization process, namely, product design and production. The proposed methodology uses a two-stage approach for supplier selection where suppliers for product design are selected in the first stage …

Static Evaluation Of The Out-Of-Plane Behavior Of Urm Infill Walls Utilizing Modern Blast Retrofit Systems, Trevor D. Hrynyk

Masters Theses

"Previous investigations have shown that the use of modern retrofit systems can significantly improve the behavior of URM infill walls subjected to variable out-of-plane loads. It has also been shown that the use of externally bonded retrofit systems can greatly reduce the amount of fragmentation and debris scatter that is found to occur in URM walls subjected to high intensity blast loads...The main objective of this study is to investigate, through static testing, the use of modern materials for the purpose of improving the behavior of URM walls subjected to blast loads. This study implemented externally bonded FRP grids and …

Empirical Investigation Of Enhanced Air Fins, Stephen John Dale Rucker

Masters Theses

"Enhanced convective heat transfer surfaces have been a subject of interest for quite some time. Many different methods have been used to increase the amount of heat transfered from a surface. However, nearly all surface enhancement methods come with a price, frictional losses. This thesis studies the use of enhanced convective heat transfer surfaces on air fins in the laminar, transitional, and turbulent flow regimes with emphasis on the transitional regime. A major goal of this thesis is to further the understanding of the influence of an enhanced wall geometry on the transition from laminar to turbulent flow. Causing the …

Enhanced Functional Analysis System Technique For Managing Complex Engineering Projects, Sofia Tan

Masters Theses

"This study presents an Enhanced Functional Analysis Systems Technique (EFAST) tool to facilitate communication amongst various stakeholders such as the customers, program managers, systems architects, and systems engineers. the EFAST maps the customer requirements to downstream system functions and subsystem/component requirements, and outlines the interactions between various system and subsystem level and activities using a top-down approach. A bottom-up approach is used to populate the system element cost and time estimates. The EFAST tool compares the budgeted development resources with the estimated development resources to provide a realistic picture for realizing project in terms of performance, cost, and schedule. The …

Interactive And Dialogue Based Learning In Engineering Education, Siddartha Thummuri

Masters Theses

"This thesis focuses on a class room architecture that provides high levels of interactivity which enhances the students' learning environment both in distance and on-campus contexts and forms a basis for practical learning. Two analyses are presented in this thesis, the first one being a simple measure of levels of interactivity in this course architecture, based on rubric and the second one, a comparative analysis, to demonstrate the effectiveness of interactive (multi-directional information flow) classrooms as opposed to conventional (unidirectional information flow) classrooms and that this course architecture is ideal for enhancement of distance learning and an excellent route to …

Executable System Architecting Using Systems Modeling Language In Conjunction With Colored Petri Nets - A Demonstration Using The Geoss Network Centric System, Renzhong Wang

Masters Theses

"Models and simulation furnish abstractions to manage complexities allowing engineers to visualize the proposed system and to analyze and validate system behavior before constructing it. Unified Modeling Language (UML) and its systems engineering extension, Systems Modeling Language (SysML), provide a rich set of diagrams for systems specification. However, the lack of executable semantics of such notations limits the capability of analyzing and verifying defined specifications. This research has developed an executable system architecting framework based on SysML-CPN transformation, which introduces dynamic model analysis into SysML modeling by mapping SysML notations to Colored Petri Net (CPN), a graphical language for system …

A Simulation Environment Modeling The Use Of Wireless Sensor Networks For The Detection And Mapping Of Wildfires, Matthew Gann

Masters Theses

"Over the past 5 years, billions of dollars have been spent fighting wildfires which consume thousands of acres. Currently, satellites are the primary source of information regarding the location of large scale wildfires. The satellites in use are capable of reporting the location of the wildfire, but these reports are generated infrequently and have a low spatial resolution, where the reported location of the fire can be off by 500 meters. Timely detection (latency) and frequent report (throughput) are needed to help prevent the destruction caused by wildfires. This thesis, a system is described based on an ad-hoc wireless sensor …

On-Line Inspection And Thermal Properties Comparison For Laser Deposition Process, Yu Yang

Masters Theses

"This thesis is focused on comparing the laser deposition cladding with intended design model and comparing the effect of laser deposition process on thermal properties with traditional welding process. It is research on two aspects of laser deposition cladding. The first part of the thesis is aimed at solving the geometric inspection of laser deposition cladding, and the second part is for comparing the thermal properties of laser deposition cladding to samples of conventional welding process"--Introduction, page 1.

Printed Circuit Board (Pcb) Loss Characterization Up-To 20 Ghz And Modeling, Analysis And Validation, Abhilash Rajagopal

Masters Theses

"Dielectric properties and losses are increasingly more important in signal link path characterization, as data rates increases. High-frequency effects such as dielectric losses, dispersion and skin-effect losses need to be considered. For ensuring signal integrity, it is important to characterize losses of printed circuit board (PCB) dielectrics. To extract dielectric properties of a stripline transmission medium, an analytical technique was used...Two test materials were studied, and the extraction procedure was refined. This technique was applied to microstrip transmission lines. Two analytical solutions were derived for extracting practical material parameters. A microstrip test vehicle was designed and the two extraction methods …

Configuration, Manufacture, Assembly, And Integration Of A University Microsatellite, Lori Ann Ziegler

Masters Theses

"The Space Systems Engineering Team at the University of Missouri-Rolla (UMR), in conjunction with a number of Air Force, NASA, and industry mentors, is working toward the design, development, and launch of its first satellite, UMR SAT (University of Missouri-Rolla Satellite). This thesis documents the design of the UMR SAT satellites, specifically focusing attention on the layout of all components, component boxes designed for containment and protection from electromagnetic interference and the attachment of components inside the boxes and the boxes to the structure. This thesis also discusses the development of UMR SAT with challenges faced in manufacturing and prototyping …

Characterization Of Coarse Aggregate Angularity Using Digital Image Processing, Gregory Allen Swift

Masters Theses

"This thesis involves a comparative analysis between well-established physically performed measurements for coarse aggregate and an image-based system. A thorough literature review was conducted, focusing on the importance of aggregate shape and how it is measured. In addition, state of the art in image-based aggregate measurement was reviewed along with the impacts and difficulties of an image-based methodology. Physical testing, consisting of Uncompacted Void Content, Index of Particle Shape and Texture (Compacted Voids), and Percent of Fractured Particles (fractured face or crush counts), was performed on aggregate control samples prior to testing on bulk aggregate samples. All aggregate samples were …

Current Measurement In Power Electronic And Motor Drive Applications - A Comprehensive Study, Asha Patel

Masters Theses

"Current measurement has many applications in power electronics and motor drives. Current measurement is used for control, protection, monitoring, and power management purposes. Parameters such as low cost, accuracy, high current measurement, isolation needs, broad frequency bandwidth, linearity and stability with temperature variations, high immunity to dv/dt, low realization effort, fast response time, and compatibility with integration process are required to ensure high performance of current sensors. Various current sensing techniques based on different physical effects such as Faraday's induction law, Ohm's law, Lorentz force law, magneto-resistance effect, and magnetic saturation are studied in this thesis. Review and examination of …

Development, Modeling, And Simulation Of A Nano Aerial Vehicle Using Empirical Data, Wyatt Emery Davenport

Masters Theses

"The ultimate goals of this study were to use experimental data to estimate the flight capabilities of a flapping wing nano aerial vehicle (NAV), estimate the power required to provide such flight, and develop a controller approach for future use in the design of this aircraft. The experimental data is a collection of measurements of the normal force on a flapping wing taken in stationary water, and was used to develop empirical coefficient derivatives for use in the dynamic modeling of the NAV"--Abstract, page iii.

Energy Efficient Processor Operation And Vibration Based Energy Harvesting Schemes For Wireless Sensor Nodes, Phani Kumar Gajjala

Masters Theses

"A wireless Sensor Network (WSN) is a network of spatially distributed autonomous sensors deployed in the environment in order to cooperatively monitor physical or environmental conditions such as temperature, sound, pressure, motion or pollutants at different locations. Each node in a sensor network is equipped with a radio transceiver, a microprocessor and an energy source such as a battery which should be replaced periodically. To increase the lifetime of the network keeping the small size in mind, methods should be put in place to reduce the power consumption of the sensor node or increase the node life and/or to supply …

Shielding Characteristics Of A Commercial 19-Inch Rack-Based Cabinet, Jue Chen

Masters Theses

"From an electromagnetic compatibility perspective, a commercial 19-inch rack-based cabinet of 40U height is comprised of different functional modules housed in well-shielded enclosures. Three methodologies are applied to investigate the overall shielding performance of various cabinet features, including doors, side panels and cable egress, an important feature that is of primary interest here"--Abstract, page iii

E-Design Tools For Friction Stir Welding: Cost Estimation Tool, Pradeep Kumar Tipaji

Masters Theses

"A cost model is an important tool for product design and material selection. An efficient and effective cost estimation tool is necessary for early design evaluation. In this paper, cost estimation models that estimate the production cost for Metal Inert Gas (MIG), Friction Stir (FS), and Friction Stir Spot (FSS) welded joints are presented. These models determine the cost incurred to fabricate each joint along with a detailed explanation of each cost component. Each cost component has been closely analyzed and major cost components have been included in the cost model"--Abstract, page iv.

A Network Infrastructure For Real-Time Monitoring Of Campus Energy Consumption, Sandeep Kunchum

Masters Theses

"Pressing environmental concerns and rising energy costs have led many organizations to carefully review their energy consumption. Conservation requires that energy use be monitored accurately and continuously, to identify areas with higher energy consumption. Lighting has repeatedly been identified as such an area. A simple, yet effective method for reducing lighting energy consumption is retrofitting existing light fixtures with modern energy-efficient versions. The University of Missouri-Rolla is currently carrying out a lighting retrofit of all fixtures on campus. The pilot building for this project is McNutt Hall, as it has the single highest consumption of lighting energy. The results of …

Microfluidic Biosensors For Intelligent Metabolite Monitoring, Nitin Radhakrishnan

Masters Theses

"Baseline (zero-value) drift and sensitivity degradation are two common problems related with biosensors. In order to overcome these problems, there is a great need for integrating an on-demand, in situ self-diagnosis and self-calibration unit along with the sensor. Utilizing the microfluidic technology, it is possible to explore the feasibility of implementing this function without any externally coupled bulky apparatus. A microsystem including a microfluidic channel and calibration electrodes are prepared by microfabrication techniques"--Abstract, page iv.

Vision Based Leader-Follower Formation Control For Mobile Robots, Gerard Sequeira

Masters Theses

"Creating systems with multiple autonomous vehicles places severe demands on the design of control schemes. Robot formation control plays a vital role in coordinating robots. As the number of members in a system rise, the complexity of each member increases. There is a proportional increase in the quantity and complexity of onboard sensing, control and computation. This thesis investigates the control of a group of mobile robots consisting of a leader and several followers to maintain a desired geometric formation"--Abstract, page iii.

Cognitive Biases In Risk Management, William Thomas Siefert

Masters Theses

"This thesis contends that most Risk Management/Mitigation programs fail to be as effective as they could be due to a number of mostly overlooked drivers, such as motivation and cognitive biases. The issue of cognitive biases is very seldom addressed. When questioned, most engineers purport to not have any biases. They insist that they use only logic, reasoning, and math to make decisions. A set of data was collected and reviewed for this thesis. The data presented shows that cognitive biases do affect the risk management/mitigation process. Knowledge of these biases and their potential impact on a project will lead …

Identification Of Radial Streaming And Pseudopods In Dermoscopy Images, Sayali Prabhakar Deshpande

Masters Theses

"This thesis demonstrates an algorithm to identify the features of radial streaming and pseudopods found in dermoscopy images of malignant melanoma. The algorithm includes preprocessing images using the Principal Component Transform and an application of mathematical techniques to extract the desired features from the lesion image on the basis of color, size, shape, and orientation with respect to the lesion boundary. These identified features are further used to classify the lesion as malignant or benign. The proposed algorithm has produced a diagnostic accuracy of 90.50% for the training set of 31 malignant and 109 benign images and a diagnostic accuracy …

Synthesis And Characterization Of Platinum-Based Multi-Component Catalysts For Direct Methanol Fuel Cells, Li Ren

Masters Theses

"In the thesis work, Pt-based binary, ternary, quaternary alloy anode catalysts supported on sonochemically treated multi-walled carbon nanotubes (CNTs) were synthesized with ethylene glycol reduction of corresponding metal chloride salts. Inductively coupled plasma-mass spectroscopy (ICP-MS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM) were used for catalyst characterization. Cyclic voltammetry for methanol oxidation and CO stripping were used to evaluate the performance of the catalysts.

PtRu nanoparticles supported on CNTs (PtRu/CNT) were prepared under a series of pHs. It was found that the PtRu particle size, composition, and catalytic activity were all sensitive to the deposition …

Susceptibility Scanning System As Failure Analysis Tool For System Level Esd Problems, Giorgi Muchaidze

Masters Theses

"System level Electrostatic Discharges (ESDs) can lead to soft-errors (e.g., bit-errors, wrong resets). The goal of this project is to offer guidance in finding the root cause of soft-errors frequently observed using immunity scanning system. Immunity scanning is an increasingly adopted method for root cause analysis of system level immunity sensitivities. It allows localizing affected nets and ICs. At first a description of the ESD discharge process is given, which provides the necessary background for correctly analyzing ESD failures. Local scanning and in-circuit measurement techniques are expounded in this study. Further, it is shown how PCB scanning results can reveal …

Design For Test Techniques For Asynchronous Ncl Designs And Fpgas, Sindhu Kakarla

Masters Theses

"Testing of an electronic chip is an important step in the design process, as it can detect faults and ensure reliability. Design for Test (DFT) methods are used to modify existing designs to enable their testing by Automatic Test Pattern Generators. This thesis focuses on developing testing techniques for design automation of NULL Conventional Logic (NCL) circuits and for detection of capacitive crosstalk effects in Field Programmable Gate Arrays (FPGAs).

A novel technique is developed for testing asynchronous NCL designs aimed at good fault coverage with acceptable gate overhead. The technique focuses on testing stuck-at-faults in the internal feedback paths …

Manufacturing And Characterization Of Soy-Based Pultruded Polyurethane Composites, Rama Bhadra Raju Vuppalapati

Masters Theses

"In the recent past, composites have been finding various applications in civil infrastructure, marine, transportation, automotive and non-automotive applications by replacing metals in structural components. Pultrusion is considered to be a cost effective method for manufacturing composite materials.

Polyurethane resin systems form a good alternative to the conventional styrene based systems in pultrusion due to their better physical, chemical and mechanical properties. Polyols derived from soybean oil along with isocyanates produce polyurethanes that can match in many aspects with one derived from the petrochemical polyols. Even though, polyurethanes have good properties there are lots of challenges like designing unique material …

Damping Controllers For Power System Oscillations Using A Static Var Compensator, Sandhya R. Jetti

Masters Theses

"Damping of power system plays an important role in not only increasing the transmission capacity but also in stabilizing the power system, especially after critical faults. Static Var Compensator (SVC) is a shunt FACTS device which has capability of fast and continuous capacitive and inductive reactive power supply to the power system. SVCs are widely used for voltage stability but studies show that they are also effective in providing damping to the system. In this thesis, three types of SVC damping controllers are designed. The first damping controller is an optimal linear controller in which the parameters of a damping …

Manufacturing Of High Performance Composites Using Vacuum Assisted Resin Transfer Molding, V. G. K. Menta

Masters Theses

"The objective of this research is to establish and enhance the existing Vacuum Assisted Resin Transfer Molding (VARTM) process to manufacture high performance composite parts usable in the aerospace industry.

Flat, hat, pi and multi stiffened panels have been manufactured by the VARTM process using AS4-5HS and AS4-8HS carbon fabric, and SI-ZG-5A low viscosity epoxy resin. Silicone-based reusable molds have been designed and developed to manufacture stiffened panels. Dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) experiments of the SI-ZG-5A resin system were conducted to determine the storage modulus, loss modulus, and the glass transition temperature. The density and …