Engineering Commons^™

A Monte Carlo Calculation Of Neutron Reflection From Various Curved Surfaces, Charles Jack Kalter

Doctoral Dissertations

"Plane parallel neutron beams normally incident upon the curved surface of a solid reflector are studied with the Monte Carlo method. The geometries studied are cylindrical, parabolic, and hemispherical. It is shown that when the curved surface is cylindrical, a small "focusing effect" occurs in the reflected neutron beam. Parabolic and hemispherical surfaces do not show "focusing". A study of the factors which determine the spatial dependence of the reflected flux shows that the probability of emergence of a neutron, traveling a fixed distance from a point inside the reflector, depends upon the curvature of the surface. It is only …

Continuous Interfacial Polycondensation Of Nylon 6-6, Chandrakant A. Patel

Theses

Nylon 6-6 has been prepared by continuous interfacial polycondensation from hexamethylene diamine and adipyl chloride in a stirred system. The effect of monomer concentration and stirring on the intrinsic viscosity of polyamide 6-6 solution in formic acid (90%) was determined.

As stirring rate and monomer ratio increased, the intrinsic viscosity and polymer yield went through a maximum. Diffusion coefficient (D_AB) for hexamethylene diamine was calculated and from that J_D and mass transfer coefficient /D_AB were calculated. A relation between Reynolds number and J_D factor was established by correlation curve.

Comprehensive Calculations Of The Parameters Describing Proton Energy Loss In Matter, Joseph F. Janni

Nuclear Engineering ETDs

Extensive calculations have been made of the mean energy loss, pathlength, range, multiple scattering, and pathlength straggling of protons in many materials. Emphasis has been placed on obtaining accurate results, especially for heavy materials and protons of very low energy. Values of the energy loss between .01 and 1.0 Mev were obtained by smoothing and interpolating experimental information. Above 1.0 Mev, the Bethe equation with all the necessary shell corrections has been used. Values of the adjusted ionization potential have been determined by least squares fitting the Bethe equation to all available energy loss data. The polarization effect has been …

Theoretical And Experimental Study Of Explosive Closures Of 6061-0 Aluminum Pipes, Lyle E. Edwards

Mechanical Engineering ETDs

This thesis examines the use of explosives to collapse metal pipes from an applications point-of-view. A particular system is studied, both theoretically and experimentally, in order to facilitate the future design of such closures with the least possible physical testing. The calculations are based on a rigid-perfectly plastic model of the observed deformations of the tubes, and on various assumed am derived properties of the metal and sheet explosives under the dynamic conditions of closure. A computer program has been devised which simulates the actual motion of a pipe during collapse. Experimental work involved actual test firing of aluminum cylinders …

Techniques For Active 3he Activation Analysis For Carbon And Oxygen, William Mort Sanders

Nuclear Engineering ETDs

The surface and body concentrations of carbon and oxygen have been measured in various materials using ³He activation. Channeling techniques have been used to differentiate between interstitial and substitutional location of these impurities.

Thin target excitation functions were determined for (³He,p) reactions with carbon and oxygen over a ³He energy range from 2.5 to 9.0 MeV. These data were used to calculate the activation curves for various combinations of incident particle energy, impurity distributions, and material.

Information on several computer codes used during this study is presented.

Computer Solution To Inverse Problems Of Elliptic Form: V²U(X,Y) = G(A,U,X,Y), Frederick Alvin Jeter

Dissertations and Theses

One important aspect of our present age of monolithic high speed computers is the computer's capability to solve complex problems hitherto impossible to tackle due to their complexity. This paper explains how to use a. digital computer to solve a specific type of problem; specifically, to find the inverse solution of a in the elliptical equation V²U(x,y) = g(a,U,x,y), with appropriate boundary conditions. This equation is very useful in the electronics field. The knowns are the complete set of boundary values of U(x,y) and a set of observations taken on internal points of U(x,y). Given this information, plus …

Current Mechanical Fastener Specifications And Test Procedure, John Fraczek

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Field Identification Of Soils And Aggregates For County Roads, D. G. Shurig, Jean E. Hittle

Indiana Local Technical Assistance Program (LTAP) Publications

The primary purpose of this bulletin is to provide instruction to Indiana county road personnel on rating the quality of soils and pit-run materials used in the construction and maintenance of county roads. A system of soil classification is presented which provides the county highway engineer, road supervisor and inspector alike, with a common language for identifying soil types, properties and problems.

Pavement Roughness Measurement And Evaluation, Rolands L. Rizenbergs, James L. Burchett, Larry E. Davis

Kentucky Transportation Center Research Report

Vertical accelerations of a passenger in an automobile are automatically summed while traveling a section of road at 51.5 mph. A roughness index is obtained by summing the accelerations and dividing by the time elapsed during the test. The index is subjectively related to the riding quality of pavements. Continuity in measurements since 1957 has been preserved through correlations among successive vehicles involved and reference pavements.

In general, bituminous construction has yielded smoother-riding surfaces than concrete construction. No major improvements in construction were noted on bituminous pavements since 1962. The ride quality of concrete pavements, however, has improved on those …

Kentucky Pavement (Bituminous) Performance Evaluations And Design Studies, James H. Havens

Kentucky Transportation Center Research Report

No abstract provided.

The Lure Of Home, Tim Brady

Publications

This article recounts an aircraft accident that could have been avoided. The pilot ignored flight manual warnings to not fly in icing conditions. The pilot disregarded all advice to stay on the ground but he was anxious to get home and celebrate an occasion with his family. All lives lost on the flight.

Thermal Expansion Of Tungsten At Low Temperatures, Jayant S. Shah, Martin E. Straumanis

Materials Science and Engineering Faculty Research & Creative Works

Lattice parameters, thermal expansion coefficients, and Grüneisen parameters of tungsten are determined by an x-ray method in the temperature range of 180-40 K without the use of liquid gases. Lattice parameters are expressed as a function of temperature. Thermal-expansion coefficients decrease with temperature and show no anomaly in contrast to a hypothesis proposed by Featherston and Neighbours. Grüneisen parameters γ are decreasing with temperature in accordance with the theoretical predictions. © 1971 The American Institute of Physics.

The Effect Of Variable Properties On The Laminar Flow Of Gases, Norman Shilling

Dissertations

The problem of heat transfer in laminar flow of a gas through a constant diameter cylindrical tube is treated. The gas is cooled by the tube walls held at constant temperature. Two tube inlet conditions are considered: (1) fully developed velocity and uniform temperature profiles (Graetz boundary condition) and (2) uniform velocity and temperature (UTV) profiles. Results of the theoretical and experimental phases of the work are presented.

The theoretical solution is based on the compressible boundary layer equations with varying transport and thermodynamic property terms retained. For the Graetz condition, an existing finite difference solution scheme is modified for …

The Pennsylvania State University

ACUTA: Other Publications

Attached is a draft of the charter membership 'letter we discussed at the meeting in Chicago last week. PLEASE. I have no special "pride of authorship" in this type of thing, so I implore you to be ruthless in your criticism, additions, deletions, etc. We want to entice a good membership drive, not put laurels on my head. So, if you'll go over this, make comments and return to me just as soon as possible, I compile the comments, prepare the final copy and have it printed.

Durability Of Traffic Paint On Portland Cement Concrete Pavements, Assaf S. Rahal

Kentucky Transportation Center Research Report

Performance of a series of transverse lines applied to a relatively new concrete pavement, utilizing primes and pretreatments, is reported. The report includes descriptions of the location of test lines and types of paint and pretreatments, performance histories, and analysis of results. Chlorinated rubber, epoxy, and urethane paints were the most durable. Neither pretreatment nor the use of primes significantly increased durability.

Holidays From Danger, Tim Brady

Publications

A reminder to be safe during holidays to prevent fires, avoid personal injury, and stay off the roads after drinking.

Dielectric Properties Of Atactic And Isotactic Polystyrene, Thaddeus F. Kroplinski

Theses

The purpose of this investigation was to determine the dielectric constant and dissipation factor of atactic and isotactic polystyrene at 25°C and at frequencies of 0.1, 1.0, 10, and 100 kilocycles per second. In addition, the effects of molecular weight and crystallinity on the dielectric properties of polystyrene mos also studied.

Polystyrene slabs of uniform thickness mere prepared by molding the polymer under heat and pressure. The isotactic polystyrene slabs Imre annealed at 175°g for various lengths of time to achieve varying degrees of crystallinity.

The molded polystyrene slabs were fitted with circular aluminum foil electrodes to form a three …

Front Matter, University Of Missouri--Rolla

Symposia on Turbulence in Liquids

No abstract provided.

Turbulent Interface Detector Using A Multiple Array Of Single Hot Wires, W. H. Schwarz

Symposia on Turbulence in Liquids

Intermittency circuits can be used to experimentally determine some of the properties of the turbulent interface that occur in turbulent shear flows. The signal I(x,t) is unity if turbulence is present at x and zero otherwise. Using the signals obtained from detectors at one or more points, certain statistical measures of the interface position Y(x,t) can be determined. Also using a linear array of conventional single hot-wire probes, the position of the interface can be detected continuously to within some small error. The intent of this h-detector is similar to the wave-height detector used in studies of sea surfaces. The …

Experiments In Magneto-Fluid-Mechanic Natural And Forced Heat Transfer From Horizontal Hot-Film Probes, P. F. Dunn, P. S. Lykoudis

Symposia on Turbulence in Liquids

Experiments investigating magneto-fluid-mechanic effects on the heat transfer of quartz-coated hot-film probes are described. A standard heat transfer-velocity calibration curve is obtained by traversing a probe, whose axis is aligned horizontally, in the presence of a magnetic field parallel to the probe's axis. The working medium is mercury. Results indicate a significant reduction of the probe1s heat transfer in both the free and forced convection regimes.

Turbulence Measurements With The Split-Film Anemometer Probe, B. W. Spencer, B. G. Jones

Symposia on Turbulence in Liquids

The newly developed split-film anemometer probe, manufactured by Thermo- Systems, Inc. of St. Paul, Minnesota, has been applied to the measurement of two-dimensional turbulence characteristics, including turbulent shear stress, in mixing layer and boundary layer shear flows. Probes of both 6-mil and 2- mil diameters were used which had the same physical dimensions as ordinary hot-film anemometer probes. The film on this sensor is split into two 170° elements resulting in two independent sensors. This enables the probe to detect vertical as well as axial components of the instantaneous velocity vector. It therefore serves the same purpose as an x-probe, …

The Unpolarized Electrode In A Pulsating Poiseuille Pipe Flow, B. M. Bergmann, T. H. Hodgson

Symposia on Turbulence in Liquids

In recent years three workers have described methods of measurement of unsteady flow quantities in water using unpolarized electrodes. Both Binder and Chuang have attempted measurements of turbulent velocity fluctuations, whereas Dumargue described a method of fluctuating pressure measurement.

In this paper, analysis and experiment were used to critically compare the previous workers' experiments. From measurements in an oscillating Poiseuille pipe flow it is concluded that an electrode positioned in the wall detects a signal with a phase angle of π/4 ahead of the fluctuating velocity as measured by a hot-film probe in the pipe center. This is exactly the …

Current Investigations Of Turbulent Shear, S. J. Kline, G. R. Offen, W. C. Reynolds

Symposia on Turbulence in Liquids

The paper covers first a short review of the history of research on turbulent shear and second a description of current experiments which may lead to further understanding.

The first portion categorizes the kinds of data which have been taken and discusses what can be learned from each. It then summarizes what is firmly established concerning the nature of turbulent shear, mostly from work of the past decade. A description of the several interpretations of these data under theoretic study by current leading researchers is then given.

The second portion of the paper discusses the extraordinarily difficult problem of identifying …

Interpretation Of Hot-Film Anemometer Response In A Non-Isothermal Field, W. E. Burchill, B. G. Jones

Symposia on Turbulence in Liquids

A new technique for interpretation of hot-film anemometer sensor response is described. This technique has been applied to simultaneous measurement of profiles of mean velocity, the three components of velocity vector fluctuation, and temperature fluctuation in non-isothermal pipe flow of water using multiple sensors. Sensors operated in the constant temperature mode (CTA) respond to both mean and fluctuating velocity and temperature. The influence of mean temperature gradient on CTA sensor response was eliminated by appropriate adjustment of the sensors' operating resistances as the temperature gradient was traversed. The adjustments were derived from analysis of linearized CTA sensor response. A sensor …

On Velocity Measurements In Non-Isothermal Turbulent Flows, R. Chevray, N. K. Tutu

Symposia on Turbulence in Liquids

Turbulent velocity measurements in non-isothermal flows are conventionally performed by constant current hot-wire anemometry. The procedure involved however is cumbersome, the output signals are nonlinear and more critically a continuous signal of velocity fluctuations is not provided. The method described here utilizes two orthogonal wires situated a fraction of a millimeter apart. The upstream wire is operated in a low overheat, constant-current compensated mode thus providing a signal proportional to temperature while the down-stream wire, practically unaffected by the thermal wake of the first wire is operated in the constant temperature mode. Compensation for the effects of local temperature on …

Near Wall Visual Measurements In Drag Reducing Flow, H. C. Hershey

Symposia on Turbulence in Liquids

A review of several explanations for the mechanisms of drag reduction is presented. Visual studies of ordinary liquids are reviewed briefly, and visual studies in drag reducing flow are discussed. Finally, current work at Ohio State University is described where high speed motion pictures will be taken of drag reducing flow using the technique of Brodkey and Corino.

Wavevector/Frequency Spectrum Of Turbulent-Boundary-Layer Pressure, D. M. Chase

Symposia on Turbulence in Liquids

Knowledge of the wavevector/frequency spectrum of wall pressure, P(K,ω) [K = (k₁,k₃)], for a normal turbulent boundary layer has been largely confined to properties depending on the mean-convective ridge (k₁=ω/u_c). Recent theoretical work yields the wavevector dependence of P(K,ω), for flow at low Mach numbers, also in the acoustic wave number domain where K ≤ ω/c, except for undetermined functions of ωδ/U_∞. In the nonconvective but incompressive domain of wavevectors (important in underwater acoustics), apart from the proportionality to K² where ω/c ≤ K ≤ δ^-1, the …

Measurements To Elucidate The Mechanism Of Drag Reduction, R. J. Hansen

Symposia on Turbulence in Liquids

A number of investigators have attributed the reduced turbulent flow drag exhibited by polymer solutions to their high elongational viscosity. The results of a recent theoretical study of drag reduction are summarized, which show that it may instead be a consequence of the non-Newtonian behavior of polymer solutions in time-varying shear fields. Experiments are proposed to ascertain the relative importance of these transient shear effects and elongational effects in reducing drag.

Turbulent Velocity And Pressure Fields In Boundary-Layer Flows Over Rough Surfaces, W. K. Blake

Symposia on Turbulence in Liquids

This paper is a discussion of recent measurements of the statistics of the turbulent velocity and wall pressure fields in rough-wall boundary layers. These measurements, made in part by the author, have been performed over a variety of walls covering a wide range of roughness sizes and configurations. The various measurements are compared in order to determine the structure and scaling parameters of the turblulent field convected at speeds near the mean velocity of the boundary layer. The mean square turbulent velocities, their one-dimensional spectral densities, and their longitudinal and vertical microscales are compared for different walls. The velocity fields …

Effect Of Randomly Fluctuating Pressure Gradients, With Arbitrarily Specified Power Spectrum And Probability Density, On Flow In Channels, M. Perlmutter

Symposia on Turbulence in Liquids

A randomly fluctuating longitudinal pressure gradient of a non-Gaussian form and arbitrary power spectrum will cause a randomly fluctuating velocity to be superimposed on the steady incompressible flow in a channel. Pressure- gradient and velocity correlations, frequency response functions and system power loss are calculated. Numerical random pressure gradient signals were generated using Fourier series expansion, with random picking of discrete Fourier spectrum values and a nonlinear no memory transformation. Numerical values of the velocity signal were then calculated by linear transformation of the pressure-gradient signal. Pressure-gradient and velocity signals were compared for difference in amplitude, frequency, time lag, and …