Engineering Commons^™

Multidimensional Waveform Shaping In Multicarrier Systems, Ertugrul Guvenkaya

USF Tampa Graduate Theses and Dissertations

Constantly increasing demand for wireless communications in various applications has always led to new ways of modulating the radio frequency (RF) carrier signal by advancing waveform structure throughout generations. Although communication data rates are limited by the theoretical capacity, specific signaling designs for the signal that experiences natural and artificial effects in the transmission medium such as multipath fading channel, hardware impairments and multiuser environment promised better solutions in providing improved wireless access to various type of users and networks. Besides communication capacity, broadcasting nature of radio signals poses the information security as another main concern in wireless communications. In …

Synthesis Techniques For Sub-Threshold Leakage And Nbti Optimization In Digital Vlsi Systems, Shilpa Pendyala

USF Tampa Graduate Theses and Dissertations

The rising power demands and cost motivates us to explore low power solutions in electronics. In nanometer Complementary Metal Oxide Semiconductor (CMOS) processes with low threshold voltages and thin gate oxides, subthreshold leakage power dominates total power of a circuit. As technology scales, Negative Bias Temperature Instability (NBTI) emerged as a major limiting reliability mechanism. It causes a threshold voltage shift which, over time, results in circuit performance degradation. Hence, leakage power and NBTI degradation are two key challenges in deep sub micron regime.

In this dissertation, interval arithmetic based interval propagation technique is introduced as an effective leakage optimization …

Optical Communication Using Hybrid Micro Electro Mechanical Structures (Mems) And Commercial Corner Cube Retroreflector (Ccr), Sunny Kedia

USF Tampa Graduate Theses and Dissertations

This dissertation presents a free-space, long-range, passive optical communication system that uses electrostatically modulated microelectromechanical systems (MEMS) structures coupled with a glass total internal reflection (TIR)-type corner cube retroreflector (CCR) as a non-emitting data transmitter. A CCR consists of three mirrors orthogonal to each other, so that the incident beam is reflected back to the incident beam, source. The operational concept is to have a MEMS modulator fusion with TIR CCR, such that the modulators are working periodically to disrupt the evanescent waves at the air interface of one of the three back glass faces of a TIR CCR. The …

In Vacuo Fabrication And Electronic Structure Characterization Of Atomic Layer Deposition Thin Films, Michael Schaefer

USF Tampa Graduate Theses and Dissertations

Improvement of novel electronic devices is possible by tailor-designing the electronic structure at device interfaces. Common problems observed at interfaces are related to unwanted band alignment caused by the chemical diversity of interface partners, influencing device performance negatively. One way to address this problem is by introducing ultra-thin interfacial dipole layers, steering the band alignment in a desired direction. The requirements are strict in terms of thickness, conformity and low density of defects, making sophisticated deposition techniques necessary. Atomic layer deposition (ALD) with its Ångstrom-precise thickness control can fulfill those requirements.

The work presented here encompasses the implementation of an …

Direct Solutions To Perceptual Organization Problems, Ravi Kumar Panchumarthy

USF Tampa Graduate Theses and Dissertations

Quadratic optimization problems arise in various real world application domains including engineering design, microeconomics, genetic algorithms, integrated circuit chip design, probabilistic graphical models and computer vision. In particular, there are many problems in computer vision that require binary quadratic optimization such as motion segmentation, correspondences, figure-ground segmentation, clustering, grouping, subgraph matching, and digital matting. The objective of an optimization algorithm can be related to the state of a physical system, where the goal is to bring the initial arbitrary state of the system to a state with minimum possible energy. By recognizing that the Hamiltonian of nanomagnets can be expressed …

Dynamic Phasor Based Analysis And Control In Renewable Energy Integration, Lakshan Prageeth Piyasinghe

USF Tampa Graduate Theses and Dissertations

The objective of this dissertation is to carry out dynamic modeling, analysis and control of power systems with Renewable Energy Sources (RES) such as: Photovoltaic (PV) power sources and wind farms. The dissertation work is mainly focused on microgrid since it plays a major role in modern power systems and tend to have higher renewable power penetration. Two main theoretical concepts, dynamic phasor and impedance modeling have been adopted to model and analyze the power systems/mocrogrids with RES. The initial state calculation which is essential for small signal analysis of a system is carried out as the first step of …

Pathogen Removal In Natural Wastewater Treatment And Resource Recovery Systems: Solutions For Small Cities In An Urbanizing World, Matthew Eric Verbyla

USF Tampa Graduate Theses and Dissertations

Sanitation, renewable energy, and food security are among the most pressing global development needs of the century, especially for small cities with rapid population growth. Currently, 53% of the world’s population either lacks access to improved sanitation or discharges fecal waste to the environment without treatment. Furthermore, 80% of food consumed in developing regions is produced by 500 million small farms, and while many of them are still rain-fed, irrigated agriculture is increasing. The post-2015 Sustainable Development Goals, recently adopted by the United Nations, include targets to address the water-energy-food nexus. Wastewater reuse in agriculture can be an important solution …

Corrosion Of Steel In Submerged Concrete Structures, Michael Thomas Walsh

USF Tampa Graduate Theses and Dissertations

This investigation determined that severe corrosion of steel can occur in the submerged portions of reinforced concrete structures in marine environments. Field studies of decommissioned pilings from actual bridges revealed multiple instances of strong corrosion localization, showing appreciable local loss of steel cross-section. Quantitative understanding of the phenomenon and its causes was developed and articulated in the form of a predictive model. The predictive model output was consistent with both the corrosion rate estimates and the extent of corrosion localization observed in the field observations. The most likely explanation for the observed phenomena that emerged from the understanding and modeling …

Investigation Of Low Thermal Conductivity Materials With Potential For Thermoelectric Applications, Kaya Wei

USF Tampa Graduate Theses and Dissertations

Thermoelectric devices make it possible for direct energy conversion between heat and electricity. In order to achieve a high energy conversion efficiency, materials with a high thermoelectric figure of merit (ZT = S²σT/κ, where S is the Seebeck coefficient, σ is the electrical conductivity, T is the absolute temperature, and κ is the thermal conductivity) are in great demand. The standard approach is to optimize charge carrier transport while at the same time scatter the heat transport, a task that is easier said than done. Improving the electrical properties in order to increase ZT is limited since electrons …

Near-Field Microwave Microscopy For Surface And Subsurface Characterization Of Materials, Maria Fernanda Cordoba Erazo

USF Tampa Graduate Theses and Dissertations

This dissertation presents an investigation on the capabilities of Near-Field Microwave Microscopy (NFMM) for the characterization of surface and subsurface materials. Subsurface characterization refers to the detection, differentiation and imaging of dielectric, and metallic features that are coated with an insulating layer. The design, simulation and modeling, and testing of a dielectric resonator (DR)-based NFMM and a coaxial transmission line resonator-based NFMM are discussed in detail in this work. Additionally, materials differentiation and imaging capabilities of each microscope are examined using several bulk samples, liquids, GaAs MMIC circuits, and gold/glass testing patterns.

The 5.7 GHz DR-based NFMM uses a microwave …

Heat Transfer Analysis Of Slot Jet Impingement Onto Roughened Surfaces, Rashid Ali Alshatti

USF Tampa Graduate Theses and Dissertations

The effect of surface roughness on jet impingement heat transfer was investigated in this research. A numerical analysis was conducted for free surface slot jet impinging normally onto a heated plate. Six different geometries and three different plate materials were investigated. The cooling fluid used for the analysis was water, and the flow was laminar with a range of Reynolds number (Re) from 500 to 1000. Temperature distribution, local and average heat transfer coefficient, and local and average Nusselt number were presented for each case.

The steady state heat transfer results show that the increase in Reynolds number (Re) increases …

Kinematic Control Of Redundant Mobile Manipulators, Mustafa Mashali

USF Tampa Graduate Theses and Dissertations

A mobile manipulator is a robotic arm mounted on a robotic mobile platform. In such a system, the degrees of freedom of the mobile platform are combined with that of the manipulator. As a result, the workspace of the manipulator is substantially extended. A mobile manipulator has two trajectories: the end-effector trajectory and the mobile platform trajectory. Typically, the mobile platform trajectory is not defined and is determined through inverse kinematics. But in some applications it is important to follow a specified mobile platform trajectory. The main focus of this work is to determine the inverse kinematics of a mobile …

Estimating Likelihood Of Having A Brca Gene Mutation Based On Family History Of Cancers And Recommending Optimized Cancer Preventive Actions, Mehrnaz Abdollahian

USF Tampa Graduate Theses and Dissertations

BRCA1 and BRCA2 are gene mutations that drastically increase chances of developing breast and ovarian cancers, up to 20-fold, for women. A genetic blood test is used to detect BRCA mutations. Though these mutations occur in one of every 400 in the general population (excluding Ashkenazi Jewish ethnicity), they are present in most cases of hereditary breast and ovarian cancer patients. Hence, it is common practice for the physicians to require genetic testing for those that fit the rules as recommended by the National Cancer Comprehensive Network. However, data from the Myriad Laboratory, the only provider of the test until …

Use Of Fdm Components For Ion Beam And Vacuum Applications, Eric Miguel Tridas

USF Tampa Graduate Theses and Dissertations

This study focuses on novel approaches to the modeling and construction of devices used in ion beam and vacuum systems. Turbulent computational fluid dynamics simulations were performed to model the air flow into an ion funnel system. The results of these simulations were coupled one-way with electrodynamics simulations of the fields generated by the ion funnel. Using the turbulence kinetic energy (k), a spatially varying estimation of the fluctuating component of the velocity field was calculated. These resulting simulations more accurately predicted the ion transmission through the system. Using fused deposition modeling (FDM) novel construction methods for the ion funnel …

Effect Of Mineral And Chemical Admixtures On Durability Of Cementitious Systems, Victor Tran

USF Tampa Graduate Theses and Dissertations

Mineral and chemical admixtures are used today in almost all concrete mixtures to improve concrete fresh and hardened properties, and to enhance concrete durability. In this study, four mineral and four chemical admixtures were investigated: namely, metakaolin (MK), silica fume (SF), Class F fly ash (FA), blast-furnace slag (BFS), two high-range water reducers (SP), water reducer/retarder (WRD), and air-entrainer (AEA). The objective of this study is to assess the effects of commonly used mineral and chemical admixtures on the durability of the cementitious system. Two durability issues were addressed in this study: the potential of the cementitious system to generate …

The Development Of A Fluorescence-Based Reverse Flow Injection Analysis (Rfia) Method For Quantifying Ammonium At Nanomolar Concentrations In Oligotrophic Seawater, William Abbott

USF Tampa Graduate Theses and Dissertations

The goal of this thesis was to adopt a reverse flow injection analysis (rFIA) technique to the fluorometric analysis of the reaction o-phthaldialdehyde (OPA) with ammonium, allowing accurate measurements of ammonium concentrations lower than the detection limit of the widely used indophenol blue (IPB) colorimetric method while accounting for the background fluorescence of seawater. Ammonium is considered an essential nutrient for primary productivity, especially in the nutrient depleted surface ocean where as the most reduced form of dissolved inorganic nitrogen, it is readily assimilated via metabolic pathways. Challenges in the quantification of ammonium require more sensitive analytical techniques for …

Synthesis, Characterization And Ferroelectric Properties Of Ln-Type Znsno3 Nanostructures, Corisa Kons

USF Tampa Graduate Theses and Dissertations

With increasing focus on the ill health and environmental effects of lead there is a greater push to develop Pb-free devices and materials. To this extent, ecofriendly and earth abundant LiNbO₃-type ZnSnO₃, a derivative of the ABO₃ perovskite structure, has a high theoretically predicted polarization making it an excellent choice as a suitable alternative to lead based material such as PZT. In this work we present a novel synthesis procedure for the growth of various ZnSnO₃ nanostructures by combined physical/chemical processes. Various ZnSnO₃ nanostructures of different dimensions were grown from a ZnO:Al template …

Design, Fabrication And Analysis Of A Paver Machine Push Bar Mechanism, Mahendra Palnati

USF Tampa Graduate Theses and Dissertations

Now-a-days, the major challenge that’s being faced by the concrete industry is the cleaning of concrete handling equipment. Concrete consists of aggregates, which harden with time, and the transportation of concrete mixture within the plant is a significant problem. This will not only increase the overall maintenance cost, but will lead to loss of raw materials, affect the rate of production, and reduce the lifetime of concrete handling equipment.

The present study focuses on the design and implementation of an adaptive cleaning mechanism in the concrete industry and its importance in achieving efficient cleaning, which is tested to verify its …

Operation And Monitoring Of Parabolic Trough Concentrated Solar Power Plant, Harsha Vardhan Amba

USF Tampa Graduate Theses and Dissertations

The majority of the power generated today is produced using fossil fuels,emitting carbon dioxide and other pollutants every second. Also, fossil fuels will eventually run out. For the increasing worldwide energy demand, the use f reliable and environmentally beneficial natural energy sources is one of the biggest challenges. Alongside wind and water, the solar energy which is clean, CO2-neutral and limitless, is our most valuable resource.

Concentrated solar power (CSP) is becoming one of the excellent alternative sources for the power industry. The successful implementation of this technology requires the efficient design of tracking and operation system of the CSP …

Evaluating Corrosion Resistance Of Reinforcing Steel In A Novel Green Concrete, Andrea Carolina Ramirez

USF Tampa Graduate Theses and Dissertations

Reinforced concrete structures are expected to have a long service life with minimal maintenance. Corrosion of reinforcing steel is a major factor in reducing concrete structure lifespan, as corrosion products occupy a larger volume than that of the consumed steel and generate tensile stresses that crack the concrete cover. Procedures to control corrosion in traditional concrete, which is made with Portland-cement (PC), have been well established. However, in recent years novel concrete materials based on alternatives to normally cured PC have been developed in response to global needs to reduce greenhouse gases emissions. In particular, a promising new cement has …

Evaluation Of Low-Cost Low Impact Development Practices In Southwest Florida For The Control Of Urban Runoff, Laura Kathren Rankin

USF Tampa Graduate Theses and Dissertations

Stormwater management is required due to development and alteration of the natural environment. It is heavily regulated in Florida and at the national level. Over the last two decades, Low Impact Development (LID) has been promoted as a sustainable and environmentally friendly method of controlling urban runoff. Case studies, provided in Chapter 2, show that LIDs can restore watershed hydrology by balancing the water budget. The difference in runoff between pre-development and post-development appears to increase with soil perviousness. However, the potential for mitigating the impacts of urbanization through runoff reduction is also greater for pervious, sandy soils that dominate …

Binding Of Nitrite In Concrete, Cement Mortar And Paste, Saad Alshehri

USF Tampa Graduate Theses and Dissertations

Calcium nitrite as a corrosion inhibitor is mainly used to protect steel reinforcement in concrete by reducing its corrosion rate. Hence the effectiveness of calcium nitrite depends on its availability as a free nitrite in the pore solution. The present research work aims to determine the concrete mixture component mostly responsible for nitrite binding in concrete. Firstly, the experimental program included testing of nitrite binding in cement paste. Secondly, the effect of adding the fine aggregate (mortar mix) on nitrite binding was assessed. Finally, the mix with coarse aggregate (concrete mix) was evaluated. In-situ leaching method was used to obtain …

Feasibility Of Cathodic Protection In Grouted Post Tensioned Tendons - Exploratory Model Calculations, Jacob Dharma Bumgardner

USF Tampa Graduate Theses and Dissertations

Recent corrosion related failures of grouted post tensioned tendons, even after the introduction of improved grouts, have led to renewed interest in supplemental or backup means of corrosion control for these systems. A finite element model is presented to explore feasibility of impressed current cathodic protection of strand in grouted tendons. The model examines polarization evolution as function of service time and includes consideration of anode placement and size, grout porosity, pore water alkalinity, electrochemical species diffusivity and applied voltage on the polarization efficacy and durability of such a system. The exploratory model projections suggested that, within the context of …

Consumer Perception And Anticipated Adoption Of Autonomous Vehicle Technology: Results From Multi-Population Surveys, Nikhil Menon

USF Tampa Graduate Theses and Dissertations

Emerging automotive and transportation technologies, such as autonomous vehicles (AVs) have created revolutionary possibilities in the way we might travel in the future. Major car manufacturers and technology giants have demonstrated significant progress in advancing and testing AV technologies in real-life traffic conditions.

Results from multi-population surveys indicate that despite enjoying moderate familiarity with AVs, more than 40% of the respondents were likely to use them when they become available. Simply looking at the demographic differences without paying any regard to the perceptions might suggest that the demographic differences are the primary causal factors behind the differences observed in the …

Kelvin Probe Electrode For Field Detection Of Corrosion Of Steel In Concrete, Leonidas Philip Emmenegger

USF Tampa Graduate Theses and Dissertations

While the Kelvin Probe (KP) has been used in a variety of surface scanning applications, the use of the KP in reinforced concrete structures to detect corrosion has been pioneered by previous work performed at the University of South Florida. However, in that work, the scale and construction of the probes was not suited to use in the field. This is primarily attributable to the small operating disk-to-concrete gap which would make the probe unable to accommodate road conditions, such as irregularities in the grading of the road, and local pitting of the surface. Therefore, it was important to investigate …

A Study Of Digital Rf Phase Shifters Fabricated With Additive Manufacturing, Yaniel Vega

USF Tampa Graduate Theses and Dissertations

Digital RF phase shifters fabricated using additive manufacturing processes are presented and studied. The purpose is to explain the performance differences between phase shifters fabricated using additive manufacturing and those fabricated with conventional subtractive techniques. All phase shifters are designed to operate at a center frequency of 2.45 GHz with a 100 MHz bandwidth. The 1-bit 45° switched line phase shifters have an average insertion loss of 1.3 dB and a 220 mm² footprint, while the 1-bit 180° high-pass low-pass phase shifters have an insertion loss 1.56 dB and a 180 mm² footprint. The 4-bit high-pass low-pass, switched …

Passive Symmetry In Dynamic Systems And Walking, Haris Muratagic

USF Tampa Graduate Theses and Dissertations

The ubiquitous nature of symmetry lends itself to be taken for granted, however the breath of research on symmetry encompasses several disciplines. In engineering, studies centered on symmetry often address issues in dynamic systems theory, robotics, and gait rehabilitation. This thesis presents findings on two specific topics dealing with passively induced symmetry; dissimilar rotating systems and human gait. Past studies on passive symmetry in dynamic systems often incorporate physical coupling or a controller. This thesis presents a technique to passively induce symmetry between two dissimilar systems that are not physically connected. This work also presents a human gait study consisting …

Embedded System Design Of A Real-Time Parking Guidance System, Omkar Dokur

USF Tampa Graduate Theses and Dissertations

The primary objective of this work is to design a parking guidance system to reliably detect entering/exiting vehicles to a parking garage in a cost-efficient manner. Existing solutions (inductive loops, RFID based systems, and video image processors) at shopping malls, universities, airports etc., are expensive due to high installation and maintenance costs. There is a need for a parking guidance system that is reliable, accurate, and cost-effective. The proposed parking guidance system is designed to optimize the use of parking spaces and to reduce wait times. Based on a literature review we identify that the ultrasonic sensor is suitable to …

Modeling Intrastate Air Travel: A Case Study Of The State Of Florida, Kai Liao

USF Tampa Graduate Theses and Dissertations

Florida is a state in the southeastern region of the United States. Its infrastructure allows for several travel modes including: rail, automobile, bus, aircraft, and ship. However, most intrastate travelers in Florida are limited to two practical choices: travel by car (ground mode) or travel by air (air primary mode). Due to the dramatic growth of Florida’s population over recent years, traffic has become a critical factor that impacts Florida’s development. This thesis focuses on intrastate air primary mode and develops decision making models that could aid government and airline companies to better understand travelers need and as such plan …

Tailoring The Pore Environment Of Metal-Organic And Molecular Materials Decorated With Inorganic Anions: Platforms For Highly Selective Carbon Capture, Patrick Stephen Nugent

USF Tampa Graduate Theses and Dissertations

Due to their high surface areas and structural tunability, porous metal-organic materials, MOMs, have attracted wide research interest in areas such as carbon capture, as the judicious choice of molecular building block (MBB) and linker facilitates the design of MOMs with myriad topologies and allows for a systematic variation of the pore environment. Families of MOMs with modular components, i.e. MOM platforms, are eminently suitable for targeting the selective adsorption of guest molecules such as CO₂ because their pore size and pore functionality can each be tailored independently. MOMs with saturated metal centers (SMCs) that promote strong yet reversible …