Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Theses and Dissertations

Discipline
Institution
Keyword
Publication Year

Articles 11311 - 11340 of 11490

Full-Text Articles in Engineering

A Robotic Tactile Sensor Incorporating Silicon Planar Technology: A Piezoelectric Polyvinylidene Fluoride Film, And On-Chip Signal Processing, Robert C. Fitch Jr. Dec 1990

A Robotic Tactile Sensor Incorporating Silicon Planar Technology: A Piezoelectric Polyvinylidene Fluoride Film, And On-Chip Signal Processing, Robert C. Fitch Jr.

Theses and Dissertations

This research effort pursued the design, fabrication, and test of a robotic tactile sensor. The VLSI integrated circuit (IC) portion of the sensor included a 7 x 7 array of metal electrodes which were individually connected to identical MOSFET amplifiers. A 25 micrometers thick patch (6 mm x 6 mm) of piezoelectric polyvinylidene fluoride (PVDF) film was attached to the array with a non-conductive adhesive, thereby creating an array of taxels. Charge, generated by the PVDF film, was detected by the amplifiers. The outputs of these amplifiers were connected to onchip signal circuitry designed to produce a single stream of …

Go to article

Silicon Hybrid Wafer Scale Integration (Wsi) Used To Fabricate A Hilbert Transform Integrated Circuit Module, Daniel J. Gaughan Dec 1990

Silicon Hybrid Wafer Scale Integration (Wsi) Used To Fabricate A Hilbert Transform Integrated Circuit Module, Daniel J. Gaughan

Theses and Dissertations

This research was performed in order to develop a superior processing schedule for fabricating Wafer-Scale Integration (WSI) circuit modules. This technology allows the design of circuitry that spans the entire surface of a silicon substrate wafer. The circuit element employed in this research was the Hilbert transform, a digital phase-shifting circuit. The transform was incorporated into a three Integrated Circuit (IC) die package that consisted of a mechanically supportive silicon wafer, three IC die, and a planarizing silicon wafer. The die were epoxied into this wafer using a Teflon block as a flat, and the combination was epoxied onto the …

Go to article

Electromagnetic Scattering From Impedance Strips And Impedance-Loaded Conducting Strips, Mark C. Heaton Dec 1990

Electromagnetic Scattering From Impedance Strips And Impedance-Loaded Conducting Strips, Mark C. Heaton

Theses and Dissertations

This paper investigates the scattering from impedance strips and impedance-loaded conducting strips. The UTd diffraction coefficient for an edge in a conductor is heuristically modified for impedance edges and junctions. Essentially, this is done by scaling the UTD diffraction coefficients according to changes in the geometrical optics field. The new diffraction coefficients are then used to investigate the scattering from impedance strips and impedance- loaded conducting strips. Both uniform and tapered impedances are considered. Results are compared to moment method and physical optics predictions and to measured data. The scattering pattern of a uniform impedance strip was seen to behave …

Go to article

Design And Fabrication Of An Implantable Cortical Semiconductor Integrated Circuit Electrode Array, Pierre K. Lefevre Dec 1990

Design And Fabrication Of An Implantable Cortical Semiconductor Integrated Circuit Electrode Array, Pierre K. Lefevre

Theses and Dissertations

This research furthered the processing steps of the AFIT 16 by 16 implantable cortical semiconductor integrated circuit electrode array, or brain chip. The areas of interest include the brain chip electron ics, metallization, ionic permeation, and implantation. The electronics and metallization are heavily covered. A high speed, single clock divide-by-two circuit was modified with a reset transistor and cascaded to form a ripple counter. This device had stable operation at specific source voltage and clock voltage and frequency. A 7-stage inverter with 10 unmodified divide-by-two circuits cascaded operated between 1.7 and 8 volts, and between 39 Khz and 1 Mhz, …

Go to article

Gabor Filters And Neural Networks For Segmentation Of Synthetic Aperture Radar Imagery, Albert P. L'Homme Dec 1990

Gabor Filters And Neural Networks For Segmentation Of Synthetic Aperture Radar Imagery, Albert P. L'Homme

Theses and Dissertations

This research investigates Gabor filters and artificial networks for autonomous segmentation of 1 foot by 1 foot) high resolution polarimetric synthetic aperture radar (SAR). Processing involved frequency correlation between the SAR imagery and biologically motivated Gabor functions. Methods for selecting the Gabor tuning parameters from the endless choices of frequency, rotation, standard deviation and bandwidth are discussed. Using these parameters, resulting Gabor correlation images were reduced in speckle, and more detailed. This research used cosine Gabor functions and operated on single polarization HH magnitude data. Following selection of the appropriate Gabor features, multiple Gabor representations were generated and converted for …

Go to article

A Study Of The Effects Of Noise Jamming On Radar Receivers, Paul E. Bishop Dec 1990

A Study Of The Effects Of Noise Jamming On Radar Receivers, Paul E. Bishop

Theses and Dissertations

A comprehensive study of the effects of noise jamming on various pulsed radar receiver types is proposed. First, a literature review on the sources of electrical noise and various jamming waveforms is presented. The power spectra for three noise jamming waveforms are rigorously derived. These cases are shot noise in a parallel-plate diode, a series of pulses with random amplitudes and intervals, and for a series of pulses with random amplitudes, spacing and phases. Next, the probability density functions for the output of linear and quadratic detectors are developed. For each detector type, the probability density functions for the cases …

Go to article

Characterization Of Multilayer Perceptrons And Their Application To Multisensor Automatic Target Detection, Dennis W. Ruck Dec 1990

Characterization Of Multilayer Perceptrons And Their Application To Multisensor Automatic Target Detection, Dennis W. Ruck

Theses and Dissertations

The multilayer perceptron was extensively analyzed. A technique for analyzing the multilayer perceptron, the saliency measure, was developed which provides a measure of the importance of inputs. The method was compared to the conventional statistical technique of best features and shown to provide similar rankings of the input. Using the saliency measure, it is shown that the multilayer perceptron effectively ignores useless inputs and that whether it is trained using backpropagation or extended Kalman filtering, the weighting of the inputs is the same. The backpropagation training algorithm is shown to be a degenerate version of the extended Kalman filter. The …

Go to article

Numerical Analysis Of An Axisymmetric Thrust Augmenting Ejector, Kenneth R. Gage Dec 1990

Numerical Analysis Of An Axisymmetric Thrust Augmenting Ejector, Kenneth R. Gage

Theses and Dissertations

Use of an ejector is an effective way to increase the thrust produced by a jet. In this thesis project an axisymmetric ejector concept which had been previously explored by experiment was numerically modeled. An existing axisymmetric, internal flow code based on the explicit MacCormack method was modified to incorporate primary nozzle structure and flow injection within the flowfield. Results were compared qualitatively and quantitatively with experimental results to verify the validity of the model. Internal flow structure, difficult to obtain in experiment, is easily examined. This code may be used for parametric analysis of such ejector performance parameters as …

Go to article

Analysis Of Hypersonic Blunt-Body Flows Using A Total Variation Diminishing Scheme And The Maccormack Scheme, Montgomery C. Hughson Dec 1990

Analysis Of Hypersonic Blunt-Body Flows Using A Total Variation Diminishing Scheme And The Maccormack Scheme, Montgomery C. Hughson

Theses and Dissertations

An explicit second-order accurate, total variation diminishing (TVD) scheme and the MacCormack scheme are applied to the Euler equations in axisymmetric form to study hypersonic blunt body flows. The modified flux approach of Harten, with modification by Yee, for two-dimensional flows is extended to treat axisymmetric flows. Calculated flow properties for the steady state, blunt body problem such as shock standoff distance, bow shock shape, surface pressure distribution and entropy jump conditions are compared to theory, results from the MacCormack scheme, and experimental data for Mach numbers of 3.0, 4.03, 5.06, 6.03 and 8.1. Additionally, the TVD and MacCormack schemes …

Go to article

Modeling And Analysis Of Orthotropic Plate With Circular Cutout And Adhesive Bonded Patch, Mark W. Hunter Dec 1990

Modeling And Analysis Of Orthotropic Plate With Circular Cutout And Adhesive Bonded Patch, Mark W. Hunter

Theses and Dissertations

The purpose of this study was to investigate a modeling technique to simply and adequately model an adhesive bonded patch on an orthotropic plate. This report is limited to linear material behavior. This thesis is also the basis for further work into nonlinear material range and three-dimensional stress states. To further advance aerospace battle damage repair techniques for composite repairs, a finite element model of an orthotropic plate with a hole and patch was constructed to investigate the accuracy of such a model. The fundamental problem in this model is the development of a simple and accurate method of modeling …

Go to article

Turbulence Scales In The Passage Of A Linear Turbine Cascade, James L. Acree Dec 1990

Turbulence Scales In The Passage Of A Linear Turbine Cascade, James L. Acree

Theses and Dissertations

Convective heat transfer in a turbine cascade is examined for turbulence effects. Turbulence in the free stream is varied by injection of air through a jet-grid device upstream of the cascade. Pressure and flow patterns on the blade surface, and flow velocity in two components, are examined to determine the effect of the jet-grid. Velocity and velocity fluctuation in two components are measured. Local turbulence scales through the cascade passage are determined, and local turbulent energy dissipation rate is determined. Results indicate injection of air through the jet-grid changes the angle of incidence, and therefore changes the surface pressures and …

Go to article

Vortex Bursting Over A Unit Area Aspect Ratio Delta Wing Using Vortex Paneling Methods, Donald A. Lorey Dec 1990

Vortex Bursting Over A Unit Area Aspect Ratio Delta Wing Using Vortex Paneling Methods, Donald A. Lorey

Theses and Dissertations

A unit aspect ratio delta wing is analyzes to determine if an unsteady vortex panel method can calculate the vortex bursting of the vortex developed along the leading edge. A two-dimensional vortex panel method is used to investigate wake splitting schemes of the vortex cores that comprise the vortex sheet, or wake. The worthier of the splitting methods is later implemented into the three-dimensional wake. The weighting values of the Kutta equations are investigated for the leading edges, and are determined to be problem specific. An alternative approach to management of the wake data is presented and implemented. The delta …

Go to article

A Comparison Of Molecular Vibration Modeling For Thermal Nonequilibrium Airflow, Kenneth J. Moran Dec 1990

A Comparison Of Molecular Vibration Modeling For Thermal Nonequilibrium Airflow, Kenneth J. Moran

Theses and Dissertations

The effects of thermal nonequilibrium on flows about blunt-bodies have not been studied numerically in isolation from chemical reactions. Typically, air is modeled as a perfect gas or as a chemically reacting mixture. In the former case, significant errors result at Mach numbers exceeding about 5. However, below Mach numbers around 8, the effects of chemical reactions are negligible. This study analyzes flow about a simple axisymmetric blunt-body at moderate hypersonic speeds (Mach numbers between 5-8). A first-order-accurate Roe scheme was used to compute solutions of the Euler equations assuming different gas models: perfect gas, thermal equilibrium, and thermal nonequilibrium. …

Go to article

Transverse Cracking In A Fiber Reinforced Ceramic Matrix Composite, Steven E. Bachmann Dec 1990

Transverse Cracking In A Fiber Reinforced Ceramic Matrix Composite, Steven E. Bachmann

Theses and Dissertations

The purpose of this study was to investigate the transverse cracking behavior of a fiber reinforced ceramic matrix composite. The major objectives were to determine the crack initiation stress and the minimum transverse crack spacing for different cross-ply lay-ups of SiC/1723, to provide explanation for the differences in the performance of the lay-ups, and to compare the test results to available theoretical models and to other composite systems. The thickness of the transverse ply was found to have a great effect on the transverse cracking behavior of laminates. The saturation crack spacing decreased as the transverse ply thickness was decreased. …

Go to article

Effect Of Riblets On Pressure Recovery In A Straight-Walled Diffuser, Michael K. Reagan Dec 1990

Effect Of Riblets On Pressure Recovery In A Straight-Walled Diffuser, Michael K. Reagan

Theses and Dissertations

The objective of this thesis was to investigate the effect of riblets on the pressure recovery in a straight-walled diffuser. Previous work has shown that riblets were effective in reducing the viscous drag over surfaces subjected to a turbulent boundary layer. More recently, riblets were shown to delay the flow separation within a subsonic, straight-walled diffuser by as much as 200%. The purpose of this investigation was to determine the effect on the pressure distribution within a diffuser that has had the flow separation point favorably altered by the application of riblets. Investigation results revealed that riblets not only delayed …

Go to article

Investigation Of Fatigue Damage Mechanisms In A Metal Matrix Composite Under Elevated Temperature, Barry D. Portner Dec 1990

Investigation Of Fatigue Damage Mechanisms In A Metal Matrix Composite Under Elevated Temperature, Barry D. Portner

Theses and Dissertations

This study investigated the fatigue damage initiation and progression in SCS-6/Ti-15-3 under an environment of fatigue loading at isothermal temperature. This program included two parts. First, an 808 Ultimate Tensile Strength system was set up to accommodate testing at two frequencies of 2.0 and 0.0208 cps at a constant temperature of 427° C. Second, at intervals during the load cycle process, the test specimens were characterized by establishing damage parameters based on changing modulus of elasticity, average strain, strain range, and ultimate tensile strength. Damage progression was documented in the form of failure of the fiber-matrix interface, matrix cracking, fiber …

Go to article

Development Of A Piezoelectric Polymer Film Pressure Transducer For Low Frequency And Dynamic Pressure Measurement, Ted H. Halley Dec 1990

Development Of A Piezoelectric Polymer Film Pressure Transducer For Low Frequency And Dynamic Pressure Measurement, Ted H. Halley

Theses and Dissertations

The purpose of this research was to investigate the characteristics of a small and inexpensive pressure transducer made from piezoelectric film. The pressure transducer was designed to be small and surface mountable so that the pressure distribution could be measured on an aerodynamic body. A charge reset technique was used to overcome the traditional limitations, low frequency measurements and charge decay, of a piezoelectric device.

Go to article

Modelling And Analysis Of Kernel Function And Development Of Equivalent Theodorsen Function For Three-Dimensional Aeroelastic Analysis, John K. Ryder Dec 1990

Modelling And Analysis Of Kernel Function And Development Of Equivalent Theodorsen Function For Three-Dimensional Aeroelastic Analysis, John K. Ryder

Theses and Dissertations

A fractional calculus model is developed for the kernal function under incompressible subsonic flow conditions for rectangular planform airfoils with small aspect ratio. A model valid for restricted regions of the kernel function for compressible subsonic flow conditions is also developed. Additionally, a method for numerically solving the pressure-downwash integral equation for rectangular planform wings of aspect ratio two through ten in incompressible flow is developed. An equivalent Theodorsen function for three- dimensional unsteady flow is developed, enabling the use of simpler two- dimensional aeroelastic equations of motion to fully capture the more complicated three-dimensional effects.

Go to article

Investigation Of Damage Mechanisms In A Cross-Ply Metal Matrix Composite Under Thermo-Mechanical Loading, Joel J. Schubbe Dec 1990

Investigation Of Damage Mechanisms In A Cross-Ply Metal Matrix Composite Under Thermo-Mechanical Loading, Joel J. Schubbe

Theses and Dissertations

Metal matrix composites (MMCs) are rapidly becoming strong candidates for high temperature and high stiffness structural applications such as the Advanced Tactical Fighter (ATF). This study systematically investigated the failure modes and associated damage in a cross-ply, [0/90]2s SCS6/Ti-15-3 metal matrix composite under in-phase and out-of-phase thermomechanic fatigue. Initiation and progression of fatigue damage were recorded and correlated to changes in Young's Modulus of the composite material. Experimental results show an internal stabilization of reaction zone size but degradation and separation from constituent materials under extended cyclic thermal loading. Critical to damage were transverse cracks initiating in the 90° …

Go to article

Robustness Of H2 And H∞ Design Techniques In The Design Of A Guided Missile Controller, Steven R. Kolbow Dec 1990

Robustness Of H2 And H∞ Design Techniques In The Design Of A Guided Missile Controller, Steven R. Kolbow

Theses and Dissertations

This work follows Capt. R.L. Riddle's 1989 thesis (ADA216147) which compared conventional, H2 and H∞ controlled guided missiles in simulated flyouts against an airborne target. The simulation results did not clearly demonstrate the H2 and H∞ controller advantages. In this study the missile model and simulation were refined. In addition to simulation runs, performance, noise attenuation, and μ (structural singular value) robustness analyses were conducted. Results showed areas where improvement was needed in the H2 and H∞ controllers used in the study. An H2 and H∞ controller redesign is recommended using the …

Go to article

Computational Investigation Of Circulation Control Turbulence Modeling, T. Bryan Scruggs Dec 1990

Computational Investigation Of Circulation Control Turbulence Modeling, T. Bryan Scruggs

Theses and Dissertations

A computational study of the turbulence model parameters and the effect on the flow field of a circulation control airfoil was conducted. A Beam- Warming algorithm with a modified Baldwin-Lomax turbulence model was used to solve the Navier-Stokes equations. A comparison between the effects of the Bradshaw constant on the flow field about the cylinder and the flow field about an airfoil were to be made. The lack of a steady 'converged' solution for the cylinder precluded the analysis of the flow field about a cylinder. For the airfoil, the separation point moves rearward and an enhanced vortex pattern is …

Go to article

Effects Of Specific Heat Ratio On A Simulated Chemical Laser Cavity Flow, Curt Dewayne Botts Dec 1990

Effects Of Specific Heat Ratio On A Simulated Chemical Laser Cavity Flow, Curt Dewayne Botts

Theses and Dissertations

Mixing of primary cold flow air and secondary helium to control the ratio of specific heats for the medium flowing through a simulated chemical laser nozzle/lasing cavity was accomplished. The effects of a range of mixture specific heat ratios on flowfield behavior were examined using static pressure ports in the test cavity. Schlieren photography and high speed filming aided description of the flow dynamics. Results indicated that boundary layer effects became evident in the nozzles as specific heat ratios increased. Large pressure fluctuations were observed in the cavity when helium was introduced into the flow to raise the specific heat …

Go to article

An Experimental Study Of A Sting-Mounted Single-Slot Circulation Control Wing, Michael E. Pelletier Dec 1990

An Experimental Study Of A Sting-Mounted Single-Slot Circulation Control Wing, Michael E. Pelletier

Theses and Dissertations

This wind tunnel study investigated the feasibility of using a sting and force balance to measure the aerodynamic forces and moments on a circulation control wing. A 20% this, 8.5% camber, single blowing slot, rectangular wing was designed, built, and tested in the AFIT 5-ft wind tunnel. Lift and drag coefficients were referenced to the stability axis. The Reynolds number for all tests was 950,000; angle of attack was varied from -6 to +6 degrees. Trends in the data were similar to two dimensional data, with the exception of high drag coefficients with increased blowing. Results show it is feasible …

Go to article

H2 And H∞ Optimization With A Restricted Region Of Stability, Michael J. Mares Dec 1990

H2 And H∞ Optimization With A Restricted Region Of Stability, Michael J. Mares

Theses and Dissertations

Many modern control design methods, such as H2 and H∞ optimization, guarantee that the closed-loop system will be stable. To make further use of this guarantee, the portion of the s-plane considered to be stable is restricted to a region left of a vertical line some distance alpha from the imaginary axis. This alpha shift was accomplished in the state space equations, so standard computational tools still work. now the system is not only guaranteed to be stable, but also has some guaranteed speed for the time response. The equations for guaranteeing some arbitrary damping ratio were also …

Go to article

Fracture Toughness Of Unidirectional Fiber Reinforced Ceramic Composites In Mode Ii Utilizing Laser Interferometry, Joseph W. Truskowski Dec 1990

Fracture Toughness Of Unidirectional Fiber Reinforced Ceramic Composites In Mode Ii Utilizing Laser Interferometry, Joseph W. Truskowski

Theses and Dissertations

A laser interferometry technique to measure crack opening displacement was developed and applied to end notched flexure specimens of a Corning Glass Works 1723 glass matrix with silicon carbide fibers. The laser interferometer displacement gauge monitored the crack opening displacement (COD) at the location of a support while specimens were subjected to Mode II (forward shear) cracking at room temperature via three point bend tests on a standard Instron Compression machine. Vertical displacement was measured at the center of the test specimen using a linear variable differential transformer. Load verses displacement curves were generated for both the LVDT displacement and …

Go to article

A Linear Quadratic Regulator Weight Selection Algorithm For Robust Pole Assignment, Jeffrey D. Robinson Dec 1990

A Linear Quadratic Regulator Weight Selection Algorithm For Robust Pole Assignment, Jeffrey D. Robinson

Theses and Dissertations

An advantage of linear quadratic regulator (LQR) design is that it gives a robust system by guaranteeing stability margins. This property is used to develop an algorithm for placing robust poles. The algorithm chooses the positive semidefinite weighting matrix Q and positive definite weighting matrix R by attempting to place closed loop poles at a set of desired poles. If the desired poles lie outside the allowable LQR region, the algorithm finds the achievable poles inside the region that are closest to the desired poles. The solution requires using a gradient search technique to minimize a weighted eigenvalue difference cost …

Go to article

Micromechanical Modeling Of The Fiber/Matrix Interface Region In A Metal Matrix Composite, David D. Robertson Dec 1990

Micromechanical Modeling Of The Fiber/Matrix Interface Region In A Metal Matrix Composite, David D. Robertson

Theses and Dissertations

In order to develop reasonable analytical models and to better understand how the integrity of the fiber/matrix interface in high temperature titanium based metal matrix composites effects the overall transverse normal characteristics, a parametric study of various fiber/matrix interface conditions was performed. Analysis methods included both a simplified one-dimensional mathematical model and a finite element analysis using MSC/NASTRAN. First, both strong and weak interfacial bonds were examined. Subsequently, to provide for partial bonding, a model that used an elastic-plastic interphases zone between the fiber and matrix was examined.

Go to article

Finite Element Investigation Into The Dynamic Instability Characteristics Of Laminated Composite Panels, Walter W. Taylor Jr. Dec 1990

Finite Element Investigation Into The Dynamic Instability Characteristics Of Laminated Composite Panels, Walter W. Taylor Jr.

Theses and Dissertations

Dynamic instability of a laminated composite panel subjected to a transverse load is studied. Up to cubic variations in the thickness coordinate are included in the inplane displacement field, and only the constant component is kept in the transverse displacement. The transverse shear strains retain only linear displacement terms and vary parabolically through the thickness. The complete quadratic displacement functions are included in the inplane strains. A 36 degree of freedom shell element is used to obtain numerical results. The static snap through load vs displacement curve, as well as the critical collapse load, is examined by invoking the Riks …

Go to article

Realistic Orbits About The Martian Moons, Samuel R. Bryant Dec 1990

Realistic Orbits About The Martian Moons, Samuel R. Bryant

Theses and Dissertations

Orbits about the Martian moons, Phobos and Deimos, previously found to be stable by the Poincare surface of section technique in a restricted three- body system, were investigated with non-zero eccentricity of the moons added to the dynamics of the planar four-body system (Mars, moon sun, artificial satellite). Although not strictly applicable to this case, the surface of section technique was used to verify whether or not the previously found stable orbits were realistic when a real world perturbation was added to the system dynamics. The surface of section technique involves the numerical integration of several orbits with the same …

Go to article

Predicting The Performance Of Airborne Antennas In The Microwave Regime, David P. Carroll Dec 1990

Predicting The Performance Of Airborne Antennas In The Microwave Regime, David P. Carroll

Theses and Dissertations

This study investigated the application of a high-frequency model (Uniform Geometrical Theory of Diffraction) of electromagnetic sources mounted on a curved surface of a complex structure. In particular, the purpose of the study was to determine if the model could be used to predict the radiation patterns of cavity-backed spiral antennas mounted on aircraft fuselages so that the optimum locations for the antennas could be chosen during the aircraft design phase. A review of literature revealed a good deal of work in modeling communications, navigation, identification antennas (blade monopoles and aperture slots) mounted on a wide variety of aircraft fuselages …

Go to article

First Prev Next Last