Engineering Commons^™

The Flexible Manufacturing System And Its Development In Taiwan, Chi-Shuan Liu

Theses

FMS is a new kind of manufacturing system which is flexible enough to handle a limited variety of parts. It usually consists of three main components: machine tools, a material handling system, and a computer control system. The material handling system is the key to integrating manufacturing cells into the FMS. The machine tools used in FMS are programmable and computer-controlled, having the ability to change their operation process rapidly to deal with product changeovers and part design changes. The digital computer used in FMS has the capability of handling various manufacturing processes which are not capable of being controlled …

Laminar Flow Through A Porous Annulus With Surface Suction, Stelios C. Nicolaides

Theses

A theoretical investigation was conducted to obtain the velocity, pressure and shear stress distributions for incompressible, steady, fully developed, laminar flow through an annulus, with a uniformly porous inside tube wall. Suction at the walls is a result of the pressure difference across the porous wall.

The continuity equation, momentum equation and the Darcy's law for suction velocity are analysed with an integral method. The resulting differential equations were solved using a numerical technique.

For the same radii ratio, dimensionless inlet pressures on both sides of the porous wall and dimensionless porous resistance, the dimensionless length required to reach zero …

Further Development Of Preparation And Measurement Techniques For Triode-Sputtered Mercury Cadmium Telluride Thin Films, Tai-On Chan

Theses

The modified MRC 8800 R.F. triode sputtering system was used for mercury vapor sputtering (Hg^1-xCd^x)Te targets onto N-type (111) silicon substrates with a resistivity of 70 to 90 ohm-cm. Deposition rates were in the 2.6 to 3.6 A/sec range, A Hall mobility value, at 87°K, of 2550 Cm²/V•sec with a carrier concentration of 7(10¹⁵) cm^-3 was obtained for 9 μm thick films with an X-value of 0.25. Obtaining good sputtered films reliably was dependent on having targets that would not crack when bombarded with mercury ions. Improvements in the methods used …

Computer Analysis On Discontinuity Of Cylindrical Pressure Vessels With Various Heads, Ku-Shiang Sheu

Theses

This thesis uses FORTRAN programs to compute the maximum shear stresses of the cylindrical pressure vessel with various heads. They are cylindrical, spherical, ellipsoidal, flat and conic shapes. Also the maximum shear stresses for the bimetallic joints at the vessel wall and away from the vessel wall are analyzed. Numerical examples are given for each case to facilitate the applications.

Present Reliability Of Liquid Crystal Display Devices, C. N. Suresh

Theses

The purpose of this Thesis is to study the life of liquid crystal display devices as at present available in the market place. To accomplish this, accelerated tempera-ture conditions at 77°C and 85°C were used.

During the last few years, there has grown a tremendous interest in wide range temperature operating and fast LCDs. It is therefore important to understand how LCDs behave under these conditions.

The reliability of a liquid crystal display is usually measured in terms of a quantative degradation in electrical performance and a degradation in visual appearance. The degradation in visual appear6knce may manifest itself as …

A Survey Of The Literature On Moisture In Building Construction, Lawrence Charles Tiboldo

Theses

The aim of this thesis was to evaluate the literature on moisture in buildings for its usefulness in the understanding of the theory involved in moisture transfer in buildings. Because analysis of the effects of moisture migration and development of condensation control strategies in structures depends on the knowledge of heat and moisture transfer theory as well as on the documented data on building material properties, evaluation of the usefulness of the reference material will serve as an indication of the availability of pertinent information.

To fulfill this objective, the literature listed as references to Chapter 21 of the 1985 …

Analysis Of Bolted Rock By Computer Modeling, Niann-Chyun Wang

Theses

A computer model-based on VAX-ANSYS system was developed to model the behavior of multi-layer rock systems reinforced by pretensioned rock bolts. Three models were utilized for this study. The third model represents the friction between interlayers occuring due to the tensioned rock-bolts. Results obtained from this study compare favorably with those obtained from equations developed from model studies. An attempt has been made to study the effects of creep on the behavior of the rock-layer system.

Spectrum Analysis And Real-Time Analysis Of Electroencephalograms, Suzanne Hesook Won

Theses

The analysis of the EEG background waveform is studied by two techniques, spectrum analysis and real-time analysis. The spectrum analysis is performed by using Fast Fourier Transformation (FFT) on a segment of the signal. The resulting signal is classified into different band types such as delta, theta, alpha and beta, to see the power in each band, and the magnitude of the power on the left and right side if the brain is evaluated for asymmetry. The mean power frequency shows the frequency where the maxinum power exists in each band type. This type of analysis provides overall information of …

Robot Manipulators And Control, Theresa Wu

Theses

This paper on Robot Manipulators brings together theories from three fields : computer graphics, kinematic equations and microprocessor based control.

There are four chapters in this paper, chapter one is the conceptual development on homogeneous transformations, express the position and orientation of the transposition of an object in Cartisian coordinates. Chapter two develops the method of obtaining the Cartisian coordinate position and orientation of the end effector for a manipulator, give the joint coordinate as input and use the homogeneous transformation to express the position and orientation. Chapter 3 is a very difficult one; it solves the parameters for the …

Identification Of Linear System With Feedback Input, Jyh Yang

Theses

A new procedure with feedback input is presented for identification of continuous-time systems. Using Lyapunov's direct method to prove it asymptotic stability. For the procedure to be applicable, it's assumed that all the state variables of the plant are accessible and that there is no measurement noise so the model reference scheme can be used to identify the parameters of the plant.

The procedure results in the convergence of every parameter of a model to the corresponding one of the system as the time approaching to infinite i.e. t→∞. Digital computer simulations are provided to demonstrate the feasibility of the …

Reliability Evaluation Of Liquid Crystal Displays Under Accelerated Test Conditions, Ravi Sankar Kalyandrug

Theses

This study has determined the effects of high temperature and humidity on the reliability of liquid crystal dis-plays.

Reliability life testing was done on variety of LCD samples under different operating conditions. All the besting was done under accelerated conditions, including high temperature of 85°C and relative humidity of 70%. A number of failure modes were identified in the long series'of tests.

Among many failure modes such as peeling of seal, degradation of polarizers etc., the most important is the degradation of alignment of liquid crystal molecules. Leakage current measurements were made on all the LCD samples before and after …

Frequency Characterization Of A Thin Linear Antenna Using Diakoptic Theory, Howard Harold Smith

Theses

A frequency dependent analytical expression for the input impedance of a thin wire antenna is obtained using diakoptic theory. In diakoptic theory the linear antenna is seperated into electrically short segments where each segment is treated as a two-port network. This approach eliminates the need for an integral equation formulation. An impedance matrix is found which characterizes coupling between all segments. By expanding the free space Green's function in a power series in wavenumber k each entry in the resultant impedance matrix is obtained as a function of frequency. Enforcement of the continuity of currents and equality of scalar potentials …

Scheduling Effects Of 5-(3,3-Dimethyl-1-Triazeno)Imidazole-4-Carboxamide (Dtic) And 1,3-Bis-Chloroethyl-1-Nitrosourea (Bcnu) On Mouse Melanoma Cells B16cl5, Gracie V. Coffey

Theses

DTIC and BCNU have been demonstrated to have enhanced chemotherapeutic effects in mice bearing Bl6 mouse melanoma cells. The order of administration seems to be important in maintaining optimum effects. This was shown is a study by Hill et al. (unpublished).

In the present study, mouse melanoma cells, Bl6CL4, were treated with either DTIC or BCNU. The drug was allowed to remain on the cells for 2, 3, or 4 days. The drug-containing media were then removed, the cells were washed and fresh medium was added. The cells were incubated in an atmosphere of 5% CO2 and 95% air at …

Automated Eeg Spectrum Analysis System, Marinela C. Laguna

Theses

A computer system has been designed to acquire EEG data from monkeys and to perform the spectral and statistical analysis. The system is capable of processing two channels simultaneously, acquire 64 Kbytes of EEG data for each channel on floppy disk, do the spectrums and averages of the spectrums, and calculate the histogram amplitudes of 13 frequency bands in a range of 0-71.1 Hz.

The software gives the user a lot of choices with respect to data acquisition and processing. The relative spectral power differences between "no-drug" and "drug" experiments give information about the drug effects on the central nervous …

The Quantitative Analysis Of Airborne Particulates By X-Ray Flourescence, George C. Asteriou

Theses

Airborne particulate matter from the New Jersey State area collected on Quartz Microfiber filters was analyzed by X-Ray Fluorescence spectroscopy. The quantitative analysis of the samples against N. B. S. standards produced results which were compared with Atomic Absorption analysis

The results from the two methods were correlated by the introduction of empirical factors for each element.

However, a larger number of analyzed standards of varied composition, along with the creation of a spectral library, can minimize the need for empirical factors and yield accu¬rate results.

Transport Phenomena Of Copper Ions Through An Electromembrane, Ren-Fu Cheng

Theses

A separation process based on a new class of membrane ( the electromembrane ) was studied. Experiments were performed using three types of electromembrane to remove copper ions from aqueous solution. A Separation Cell Unit was designed and set up to investigate the transport of copper ions through the electromembranes under the influence of both an electric field and a concentration gradient. Fluxes achieved were much greater than those reported for other membrane processes, and the energy consumption was one half that of electrolytic deposition.

Vapor Pressures Of Some Coal Oil Fractions, David G. Gaydos

Theses

New data on coal tar oils and data from the literature on pure compounds and oils derived from coal were used for testing the predictions by the correlation of Maxwell—Bonnell. Based on the observation that the discrepancies between the predicted values and the data are systematic, recommendations were deduced on needed modifications to the correlation. A proposal for modification to the Maxwell and Bonnell correlation to improve prediction of vapor pressures of highly aromatic fuel fractions with characterization factors of8 UOPK 10.5 was made.

Experimental data were taken on vapor pressures of fractions of coke oven coal tar oils and …

The Biodegradation Of Phenolics Using Mixed Liquor From Passaic Valley Sewerage Commissioners Plant, Newark, New Jersey, Daewon Pak

Theses

The biological degradation of phenol, O-chlorophenol, and 2,6-dichlorophenol was studied at room temperature in aerated 5 liter batch reactors using mixed liquor from Passaic Valley Sewerage Commissioners Plant (Newark, New Jersey). From the concentration versus time data, kinetic rate constants were determined for phenol (at 100 ppm), 2'-chlorophenol (at 20 ppm), and 2,6-dichlorophenol (at 10 ppm). Air stripping and adsorption were determined to be insignificant removal mechanisms for the three compounds studied.

It was noted that the biodegradation rates increased after the organisms were acclimated to 100 ppm phenol. In addition, on substrate exposure, the degradation rate increased from the …

The Kinetics And Hepatotoxicity Of Benzyl Chloride Vapor In Rats, Hari V. Rao

Theses

Male Sprague Dawley rats (250g) were exposed to benzyl chloride vapor at a concentration of 220 ppm for 6 hours. During inhalation, the blood benzyl chloride concentration increased to reach a steady state level of 9-10 ug/ml between 4 and 6 hours of exposure. A small concentration of benzyl chloride (0.86 ug/ml) was present in the blood four hours after the termination of exposure. The absorption half life was 0.53 hours (0.39-0.81) and the elimination half life was l.12 hour (0.93-l.40).

The absorbed benzyl chloride was largely retained in the blood and some of it (0.22 ug/g) was sequestered into …

Protective Laboratory Measures For The Flexible Wall Permeameter And The Atterberg Limits Tests Using Hazardous And Toxic Chemicals, Robert A. Tetla

Theses

Safety procedures for performing geotechnical testing with hazardous and toxic materials, excluding radioactive wastes, are developed for the Flexible Wall Permeameter and the Atterberg Limits Tests. The tests were evaluated in detail to determine the critical points at which the technician would be exposed to the hazardous and/or toxic permeant. It was found that the following safety measures should always be taken; 1) the apparatus and all testing should be undertaken in a sliding sash hood using the proper face velocity, 2) air monitoring using a personal dosimeter and/or a detector tube is required to assure that the concentration of …

Improving The Capabilities Of The Chemical Engineering Simulation System (Chess) Computer Program, Thomas Zvolensky

Theses

Chemical process simulation programs have become an indispensable tool to chemical engineers in the preparation of heat and material balances, and energy conservation studies. Since the 1960's several dozen process simulators have been developed which are in use today within companies and through computer service bureaus. Due to advances in the areas of unit operation analysis and thermodynamic relations, these programs require periodic modification. This thesis describes the programming modifications made to the Chemical Engineering Simulation System (CHESS) version 2.0, computer program. This undertaking was considered warranted since no improvements have been made to CHESS since its release in 1971. …

Human Factors In The Design Of Computer Graphics Input/Output Interfaces, Michael Uche Amadi

Theses

Computers are used for solving problems of various kinds and therefore, if the users are to fully benefit from the systems, they must be considered during the earliest stages of the system development. There are three major classes of computer users namely: naive, managerial, and scientific-technical. These users have different characteristics that the designer must consider within his/her system. Only by including such distinctions will these user groups each be able to perform at their respective optimum levels. Just as there are different users, there are also numerous applications to which computers can be applied. This thesis will be restricted …

Buckling Of Some Grooved Columns, Clovis Georges Baaklini

Theses

Columns with two types of transverse grooves are analyzed: a one-sided groove whose bottom is parallel to a vertical plane and cross-section is constant, and a concentric uniform groove. Then, for illustration and to be more specific, round columns are selected such that the cross-section becomes partially circular, for one-sided grooves and totally circular for a concentric groove. The columns are simply supported at both ends and subjected to a compressive eccentric load P at eccentricity e. The static equilibrium of such columns is studied via two types of solutions: the solution to three-segment column and a substantially simpler but …

Analysis And Application Of Automatic Guided Vehicle Systems, Mansuk Bae

Theses

It is the intent of this thesis to analysis the practical applications of Automatic Guided Vehicle Systems (AGVS) as a vital aid in the development of material handling operations within a variety of business sectors.

An evaluation of basis concepts, structural components, practical applications and benefits, and future accessments of AGVS, in terms of material handling are fully discussed. Additionally, a computerized simulation model that calculates "How many Automatic Guided Vehicles Are Needed?" under specific factory conditions and external environmental factors, is both tested and result evaluated.

The author concludes that the use of AGVS as a method for material …

An Integrated, Interactive Analysis And Design Of High-Rise Buildings On Micro-Computers, Vijayakumar Balusu

Theses

The implementation of Computer-Aided-Software, coupled with matrix and finite element techniques permitted the analysis and design of structures to the desired degree of accuracy and modelling. The successfulness of micro-computers in a vastly business oriented market has prompted the structural engineer to take advantage of cheaper and efficient micro-computers in the analysis and design of structures particularly the high-rise buildings. The availability of a comprehensive, integrated software for the analysis and design of high-rise building frames that can be operated on a micro-computer is either not currently available in the market or the available software programs do not fulfill the …

The Evaluation Of New Jersey's Remedial Response Program With Regard To The Use Of Risk Assessment In Determining Extent Of Cleanup, Susan Christine Gieser

Theses

In order to effectively manage the cleanup of hazardous waste sites the New Jersey Department of Environmental Protection developed a comprehensive Master Plan. Under P. L. 1983, c. 222 (A-1255) the Hazardous Waste Advisory Council was charged with reviewing New Jersey's remedial action program. One issue identified by the Council for review was the use of risk assessment for determining extent of cleanup. The study was comprised of a literature search, review of legislation that impacts on this issue, interviews with DEP personnel, and consultation with others from academia and industry to recommend what is an acceptable risk and its …

The Accident Prevention Responsibilities Of Management, Kenneth A. Hogue

Theses

The principles of industrial safety described in this paper are discussed from the viewpoint of the industrial supervisor. Maintaining a safe work environment is considered to be a prime responsibility of line supervisors. Accident prevention is viewed as avoidance of unsafe acts and conditions. Guidelines are suggested which enable the the supervisor to impart a safety consciousness on the worker. The Occupational Safety and Health Act and its practical implications are discussed from the standpoint of reporting, correction of unsafe conditions, and penalties. Recommendations are made in the areas of training, communication, and employee motivation.

A Parameter Identification System For The Human Electroretinogram, Yu-Huai Hsiao

Theses

The human Electroretinogram (ERG) is obtained in a clinical test to detect physiological abnormalities in the eye. A mathematical model of the ERG has been developed, as well as a system to identify its parameters. The system utilizes several computers. The data acquisition and initial processing is done on a previously developed system at the Eye Institute of New Jersey and the University of Medicine and Dentistry of New Jersey, which has been modified to provide the facility for further processing. Software was developed to use a MINC-11/23 computer at New Jersey Institute of Technology to transfer data between the …

Skyline Technique For Least Square Temporal Finite Element Method, Ying-Woei Hu

Theses

Skyline technique is known to be one of the most efficient numerical methods for solving symmetric and positive definite simultaneous linear algebraic equations whose coefficient matrix is banded and sparse. This technique considers non-zero elements below the skyline only and manipulates Gaussian elimination process efficiently.

In recent years, the finite element methods applied to discretize the space domain has been successfully extended to time domain discretization. This new technique, temporal finite elements, makes it possible to numerically solve initial value problems in a manner similar to boundary value problems.

This thesis introduces skyline technique to one of the temporal finite …

Standardization, Certification Its Impact On Electronic Systems Manufacturing, Lawrence M. Johmann

Theses

This thesis is a result of an in-depth study of the standardization and certification process in various countries throughout the world. The study was undertaken due to the general lack of readily available information on the subject and problems the author encountered while involved in standardization and certification activities at his previous place of employment.

The thesis discusses product and process standardization and certification and its impact on electronic systems manufacturers. First, the need for standardization and certification is established and its history is reviewed, then the various types and classifications are addressed. Subsequently, standardization in the United States, in …