Engineering Commons^™

Steady-State Operation Of Bench-Scale Activated Sludge Process Using Phenol And 2-Chlorophenol As Substrates, Jeffrey Richard Caputi

Theses

Experiments were conducted to determine whether a continuous process similar to the common activated sludge process could be operated at a relative steady state with phenol and 2-chlorophenol as the sole carbon sources. After a number of unsuccessful trials, process conditions were developed which allowed for operation at a relative steady state with respect to the concentration of microorganisms in the reactor and the concentration of phenol and 2-chlorophenol in the effluent.

Phenol and 2-chlorophenol were removed at better than 99 percent efficiency on a continuous basis. The mixed liquor grown under the conditions of the experiment was highly filamentous …

The Effect Of Inorganic Salts On Adsorption Of Organics By Fly Ash, Pai-Yuan Horng

Theses

Optimum amounts of inorganic salts ( monovalent, divalent, and trivalent chlorides ) added to various bituminous coal fly ashes in batch adsorption treatment experiments indicates the possibility of improving adsorption capacity.

Experiments were conducted on aqueous solutions of three priority pollutants : phenol, toluene, benzene. Both high fusion and low fusion fly ashes were used as sorbent materials. Removal of organic pollutants was measured using a total organic carbon analyzer.

Isotherm tests positively indicate that the addition of inorganic salts to fly ash significantly increases adsorption capacity. The study shows that removal of organic pollutants by fly ash depends on …

The Kinetics And Mechanism Studies Of Cathodic Electro-Initiated Crosslinking Polymerization Of Unsaturated Polyester Prepolymer, Joseph Yuan-Ji Sheng

Theses

The cathodic electro-initiated polymerization reaction of the unsaturated polyester prepolymer has been found to have the characteristics of the first order ionic initiation polymerization mechanism. The rate of polymer formation is directly proportional to the current intensity and voltage supplied, but inversely proportional to the reaction temperature. The rate of initiation can be expressed as a function of the initial concentration of the prepolymer, residence time and reaction temperature. The rate expression of the initiation step has been derived based upon the experimental data collected as follows:

ln W = k0 exp[-Ea/RT] Ca0 ln t + ln b

where k0 …

High Temperature Reactions Of Chloroform With Methane, Thomas Siozopoulos

Theses

The reactions of Chloroform with Methane were studied at atmospheric pressure in the temperature range of 550-800 deg C, and using three different reactor diameters.

The reaction was found to follow pseudo-first order kinetics in the presence of excess Methane and Argon, and the kinetic parameters were determined for each of the reactor sizes.

The resulting global Arrhenius expressions are:

For 0.4 cm ID Kexp = 2.03 * 10⁸ exp (-34000/RT)

For 1.05 cm ID Kexp = 9.86 * 10⁸ exp (-37950/RT)

For 1.6 cm ID Kexp = 4.17 * 10⁸ exp (-36760/RT)

An increase in the …

Performance Of Second Order Delta Modulation System, Reza Aghazadeh Alavi

Theses

The performance of an ordinary delta modulation (DM) system under three types of input signals was investigated. These signals were band limited Gaussian noise, 800 Hz sine wave, and speech signal. The affects of 2nd DM added to the ordinary DM in improving the performance of the system were researched. This is called a Second Order Delta Modulation System. The obtained data showed an increase of about 3dB in the overall Signal to Noise Ratio (SNR) of the system, in the worse case.

Input to the 2nd DM is the band limited error of the first DM. A linear phase …

Mrp Ii As A Tool For Inventory Management : Application, Implementation, And Its Alternatives, Yi-Hsin Chiu

Theses

MRP II has been used universally as a tool for production planning in various manufacturing systems. Its foundation of success is based on an accurate inventory management. Due to the rational pricing of computer hardware and software, the selection of an appropriate off-the-shelf MRP II package has become an important topic. Moreover, implementation of a commercial MRP II package significantly affects its capability of handling an assigned task. The scope of this thesis is to discuss how to successfully implement MRP II through a design and development of a proper inventory data base in order to expand its application. The …

Mathematical Modelling Of The Simultaneous Diffusion Of Egta And Caegta And Ca2+ In A Two-Compartment System Representing Skinned Smooth Muscle, Roderick Jon Hausser

Theses

Smooth muscle strips "chemically skinned" with Triton X-100 represent a two-compartment system consisting of the extracellular space (ECS) and the cytosolic space (CS) bounded by the permeabilized plasma membrane. Free [Ca²⁺] in such systems must be controlled with sufficiently high concentrations of Ca-buffers (EGTA). The presence of Ca-buffers, however, will oppose and delay any changes in [Ca²⁺] in both compartments. We have developed a model describing the simultaneous diffusion of Ca 2+ , EGTA and CaEGTA between bath and ECS, and ECS and CS and the chemical reaction between ligand and metal species in each compartment. …

The Design And Fabrication Of Dielectric Waveguides For Use With High Power Carbon Dioxide Lasers At 10.6 Microns, Jong Min Kim

Theses

The feasibility of constructing a feasible transission system to propagate 10.6 microns energy from a CO₂ laser is explored. The system is to be used in a clinical surgical setting to deliver as much as 100 watts of CW power from a surgical CO₂. laser to a surgical target.

The optimal transmission system is a slender flexible cylindrical structure, 1 mm in diameter and 1.5 m long. The structure should be sufficiently flexible to be bent into a 5 to 10 cm radius without a significant increase in the attenuation constant. For clinical applications the system must …

Automated Manufacturing Technology As A Factor In Production Planning And Control, Henry Steven Nicholas

Theses

The field of automated manufacturing technology is examined. The physical hardware is described, including transfer systems, feeder systems, placing devices, automated work stations, sensors, and actuators. The interrelation of the hardware elements is described and various applications are identified. The role of the control system and its interaction with the hardware is examined. The data communications network required for the control system is considered. Various types of computers, computer network structures, and process control strategies are examined.

The use of automated manufacturing technology requires a new approach to production planning and control. The traditional approach is described and several problem …

The Feasibility And Economics Of Resource Recovery Using Municipal Solid Waste, Joachim Aloysius Pinto

Theses

This thesis gives an overview of the feasibility and economics of a resource recovery project. The feasibility study of a resource recovery project is done by analyzing its markets, economics, and environmental aspects. The use of market development, accurate capital and operating cost estimation procedures and environmental impact analysis help in predicting fairly accurately the feasibility of a resource recovery facility and also gives a good estimate of the economics of the project.

The thesis also discusses the different system design that are or were used in waste-to-energy conservation. It is quite evident from the discussion that the only two …

Evaluation Of Numerical Inversion Of Laplace Transformed Solutions, Yu-Chwin Lin

Theses

Here, some linear physical systems are analyzed by using the standard Numerical Laplace Transformation and Inversion method, including undamped and damped systems:

1. Undamped system: A bar clamped at one end and at one end free.

2. Damped system: Viscously damped linear discrete system.

The advantage of the Numerical Laplace Transformation method is that it reduces the inversion of the Laplace transformed solution to numerical integration; it makes the problem much easier to solve. In the present work, we also studied a new Numerical Laplace Transformation Inversion method by Wilcox (App.0 and Ref.l). The merit of this new method is …

Reflections On Solid Modeling In Cad/Cam System, Yuh-Hwa Chyr

Theses

In this thesis, we will first study the mathematical fundamental for geometric modeling. It includes modeling space, representation scheme, and various characteristics for solid modeling. Then we discuss how a solid modeling system is integrated into an overall CAD/CAm system. What functions it performs, and what fuctions must be performed with other parts of the CAD/CAM systems. And how data can be transfered between solid modeling system and other CAD/CAM system.

Solid modeling has created a new era in CAD/CAM. A solid model is an unambiguous, three-dimensional, geometric representation of a design. The more design information a model can represent, …

Modeling And Simulation Studies On Nmos Vlsi, Chang-Joo Kim

Theses

This thesis has two parts. The first part deals with the theoretical analysis and experimental verification of the variation of channel resistance and threshold voltage as a function of drain and source voltages in NMOS transistor with the substrate taken as reference. And the second part deals with simulation and optimization of the NMOS sense amplifier circuits.

Firstly, the NMOS transistor with the substrate taken as reference node is analysed and a set of formulas is derived for the variation of channel resistance as a function of the terminal voltages. Experimental results (using SCL 4007AE from Signetics) show good agreement …

Digital Signal Processing Implementing The C Language With Graphics Spectrum Analysis Display, Anuraksa Mahanirananda

Theses

Digital Signal Processing discussed in this thesis is concerned with the transformation of signals or complex wave forms From time domain to frequency domain and vise-versa, implemented on microcomputer systems. The primary principles are: speed of transformation, ease of usage as an application program, capabilities of graphics displaying transformed data (such as power spectrum analysis), storing these data onto record files, and capability of using these data Files and programs with other application programs.

We begin by discussing briefly, the concepts of Fourier theory, Discrete and Fast Fourier Transform, algorithms of Fast Fourier Transform and bit-reversal. Then we implement these …

Microcomputer-Based Automated Feeding And Monitoring System For Eating Behavior Studies On Rats, Tseng-Huang Shih

Theses

An instrumentation system has been designed to monitor feeding behavioral experiments on rats. This instrumentation system is capable of performing these experiments in an automated manner without any human intervention. It is capable of monitoring these experiments concurrently in six cages. It exhibits several features that make it more versatile than previous feeding & monitoring systems. It is also capable of storing the data generated on to a floppy disk and later printing out the data for analysis.

Another feature that makes it more versatile is the flexibility of the system. Construction of a parameter file before doing the experiment …

High Temperature Reactions Of 1,2-Dichloroethane With Water Vapor In A Tubular Reactor, Charles E. Anderson

Theses

This study examines the reaction of l,2-dichloroethane with water vapor. The linear-flow method is utilized, assuming plug flow without axial diffusion. Normal operation is at atmospheric pressure and the reactor is a quartz tube in a thermal region 45 cm in length. Two reactor diameters of 0.4 cm and l.05 cm are used. Water and l,2-dichloroethane enter the system in liquid phase via syringe pumps. After vaporizing in heated tubing, they are combined with argon, the reactor carrier gas. The molar ratio of water to l,2-dichloroethane is 55:l and varied residence times are achieved by changing the argon flowrate. Reactor …

Trends In Metal (Pb, Zn, Ni, As And Se) Concentrations In The New Jersey Air Environment, Geoffrey Ike Ejiofor

Theses

The trend and atmospheric concentrations of five trace elements (Pb, Zn, Ni, As and Se) were studied at Newark (urban site) and Ringwood (rural site), New Jersey, during January - September 1985, whilst the Hackensack Meadowlands, New Jersey were monitored during October 1985-March 1986. The analytical procedure involved collection of the airborne particulates on a glass fiber filter using a non-dichotomous high volume sampler. The samples were digested and analyzed using the atomic absorption spectrophotometer. It was ascertained that Newark and Meadowlands exhibited higher average concentrations of Zinc and Lead than Ringwood. It was concluded all the metals originated mostly …

The Biochemical Fuel Cell : Conversion Of Waste To Energy, Charles August Mielke

Theses

A batch biochemical-fuel cell was constructed and studies on the production of bioelectric energy using an alga Scenesdesmus quadricauda, and a bacterium Desulfovibrio desulfuricans, were conducted. Results were compared for a steady state cell using various concentrations of media components and showed that a 1000-fold increase in the concentration of media components produced a net potential output of 0.03mv/ml compared to an initial output of 0.02mv/ml. Further studies showed the biochemical net potential output using activated sludge from a waste treatment facility was 0.01mv/ml compared to 0.02mv/ml for the cell using the initial media concentration.

The system exhibited steady state …

Thermal Decomposition Of Chlorobenzene In An Atmosphere Of Hydrogen, Edward Robert Ritter

Theses

The thermal decomposition of chlozobenzene was investigated in a tubular flow reactor at 1 atmosphere total pressure and average residence times of 0.02 - 2.5 seconds. The temperature range from 800 - 1010°C was studied in both a reductive atmosphere of hydrogen and an inert atmosphere of heIium. Complete destruction of chlorobenzene occurs at about 1000°C for an average residence time of 1 second in hydrogen gas. In the inert gas, the complete destruction of the reagent was not observed in the range of conditions which were studied. The major products observed for pyrolysis in hydrogen were benzene, HCl, and …

Multi-H Continuous Phase Modulation : Its Properties And Analysis, Jyung-Cheng Chen

Theses

Multi-h CPM, a generalization of CPFSK and also one of the so-called Combined Modulation and Coding schemes, is useful in digital communication systems where both the bandwidth and power are constrained. The increased signal processing complexity, which can be viewed as the third communication resource, is used to trade for both power and bandwidth, and to approach the error-free communication promised by Shannon's theorem.

The transmitted multi-h CPM signal carries a coded sequence of continuous phase changes; the possible phase states form a cylindrical trellis in phase and time, in which the modulation indices are reused in a cyclical fashion. …

Experimental Study Of Rectangular Reinforced Concrete Members Under Combined Biaxial Bending And Tension, Naresh B. Patel

Theses

In practice it is a very common case to have a column subjected to combined effects of axial tension and biaxial bending moments and very few efforts are done to get good design approach for such special members.

So for this purpose, experiments were carried out on rectangular shapecolumns. Rectangular shaped columns were casted in homogeneous with brackets - one on each end and at connections haunches were provided to avoid the possible end failure. The overall shape of this configuration was "H" shape. Two hydraulic jacks were used; one on either side of the columns and thus column section …

Logic Simulation And Methodologies For Design For Testability, Ravi Shankar Prasad Mallampalli

Theses

This thesis describes the method used for developing the standard TTL blocks using the logic simulator SPLICE1. It also gives a comprehensive overview of methods which can be used for designing a circuit which is testable. A format called Electronic Design Interchange Format (EDIF) is also described as a tool which can be used for transporting design data in the VLSI indgstry.

Biorhythms And Industrial Injuries, James Vincent Detitta

Theses

The purpose of this study is to determine whether or not a relationship exists between the time of an industrial injury and a specific position on the biorhythm scale known as a critical day.

Ninety-six employees who worked at the E. I. du Pont de Nemours Plant in Parlin, New Jersey served as a test group during 1980. In order to determine if a relationship did exist, the subjects' biorhythmic cycles for 1980 were charted and then their injury performance was monitored during that year to see if the injury date corresponded with a critical day. An additional test was …

Gas-Phase Reaction Of 1,2-Dichloroethane With Hydrogen In A Tubular Flow Reactor, Wei-Lian Lee

Theses

We have studied the reaction of 1,2-dichloroethane with H₂ in three tubular flow reactors of different diameters at atmospheric pressure in the temperature range of 550° C to 1000°C. The kinetic parameters and product distribution were experimentally determined for each size reactor. The wall and bulk reaction rate constants were decoupled via analysis of three different surface to volume reaction data.

The experimental reactor was an isothermal tubular flow reactor that operated within the domain of plug flow region. The reaction was found to follow first-order kinetics with respect to 1,2-dichloroethane when in the presence of excess hydrogen. The …

A New Density-Dependent Mixing Rule For Equations Of State, Theodore John Shatynski

Theses

A general procedure for the development of density-dependent mixing rules is demonstrated. This method is used to obtain a density-dependent local-composition mixing rule based on an extention of the work of Knox et al (1984). The resulting expression is tested with the Soave-Redlich-Kwong equation of state. Results for normal and cryogenic vapor-liquid systems for both one-parameter and three-parameter versions of the mixing rule are compared with results using the classical mixing rules.

Effect Of Center Of Gravity Location On Optimum Performance Of Random Vibratory Vehicle Suspension, Daniel Mahar

Theses

This study provides the analysis for the optimal design of a conventional vehicle suspension system, consisting of a sprung mass (vehicle body) and two unsprung masses (wheel frame), accentuated by the implementation of a damped absorber to the unsprung masses. Further, the effect of the c.g. (center of gravity) location of the vehicle body is investigated. A two dimensional, four degrees of freedom linear model is chosen. Randomly profiled terrain is assumed to impart hyperbolically distributed stationary vertical random displacements to the front and rear wheels. For generalization, nondimensional design parameters are selected. Criteria for optimization include the tire-terrain normal …

Analyze3d, A Structural Analysis Program Employing Membrane And Solid Finite Elements, James Mendham Gathercole

Theses

The purpose of this thesis is to describe the addition of an 8 and 20-node isoparametric brick element to the finite element program ANALYZE, permitting three-dimensional analysis. The reason for the addition is that even though Analyze is a relatively simple program, its simplicity makes it a good educational tool for finite element courses. The added brick element expands the use of the program for educational purposes.

In its original form, Analyze is a finite element package for static structural analysis developed at Wright Patterson Air Force Base. The program consists of four finite elements: (1) bar, (2) membrane triangle, …

The Effect Of Systemic Arterial Pressure On Microvascular Flow And Transcapillary Exchange Of Macromolecules In The Hamster Cheek Pouc, Govind Mohanlal Gawdi

Theses

Microvascular flow velocities and transport of macromolecules were studied in the hamster cheek pouch under control and acute high arterial pressure conditions, with or without topical (local) application of the vasodilating agent, bradykinin. Mean arterial pressures of 130-160% control were attained by intravenous renin infusion. The microcirculation of the cheek pouch was studied using intravital microscopy. Areas with arterioles and venules were recorded on a videotape for later analysis of red cell velocity, using an RBC tracking correlator, and vessel diameter using a video shearing monitor.

In addition, vascular permeability to macromolecules was studied in the hamster cheek pouch vascular …

Zeta Potential Measurements Of Biological Flocs Using A Streaming Potential Cell, Wayne James Gallagher

Theses

A streaming potential apparatus was assembled and tested. Its purpose was to characterize the surface of biological flocs in a wastewater environment. Samples of mixed liquor were obtained from the Passaic Valley Sewerage Commissioners wastewater treatment plant in Newark, New Jersey. Filtered mixed liquor was passed through a bed of the floc particles in the streaming potential cell, and the electric potential across the cell was measured as a function of the differential pressure drop. From these data, the zeta potential was calculated using the Helmholtz equation. Values of -0.88 and -0.44 millivolts were obtained for two mixed liquor samples.

Gallium Film Formation By Ion Cluster Beam Deposition, Te-Chuan Hsu

Theses

Gallium thin films were deposited by Ion Cluster Beam (ICB) from pure gallium. This research had two objectives: to develop a practical method of crucible heating to generate gallium clusters; and to investigate the influence of ICB system parameters on the formation of clusters and film properties. An electron-bombardment crucible heater with a novel construction was designed. The top section of the carbon crucible was kept at a higher temperature than the middle section to prevent clogging of the nozzle and " spitting " phenomena which were found to occur with the conventional design. Crucible temperatures up to about 1360°C …