Engineering Commons^™

Reliability Problems And Failure Mechanisms In Ic Packaging, Dilip J. Patel

Theses

Today, reliability is acknowledged as an important item in design and operation of electronics circuits and system.

This thesis provides information on evaluation of the reliability for hermetic and non hermetic IC packages made by different manufacturers.

Literature study concentrates on the reliability and related problems in IC packages developed between 1970 and 1988.

Several failure mechanisms and failure modes are discussed to point out how higher reliability in IC packages may be achieved.

The bibliography is given in a chronological order to help further research in this area.

Generation Of Atomic Nitrogen By Gas Discharge In Microwave Cavity, Jong-Shun Shieh

Theses

A microwave discharge system for producing atomic nitrogen at low flow rate and low pressure has been investigated. The molecular nitrogen passes through a microwave cavity in a quartz tube and is dissociated by the microwave energy. Subsequent recombination of nitrogen atoms produces a characteristic yellow glow due to the relaxation of excited molecular nitrogen to its ground state. The titration of nitric oxide with atomic nitrogen was used to measure the atomic nitrogen yield. At a 2 sccm nitrogen flow rate the atomic nitrogen yield was 8.75*10¹⁵ atom/sec, which corresponds to a nitrogen generation efficiency of about 1%. …

A Cmos Digital Temperature Sensor For Asic Vlsi Standard Cell Design, Chih-Ta Sung

Theses

This thesis describes the design of a CMOS digital temperature sensor cell including the physical layout database.This cell is designed for implementation within an ASIC VLSI chip as a standard cell . The digital temperature sensor can trigger an alarm signal and turn off power for preventing fatal damage in the VLSI chip if overheating occurs.A digital output also permits measurement of temperature over the 0 - 120°C range with ±3.4°C accuracy using standard VLSI foundry processing. Two sensing elements are implemented in a differential mode within the temperature sensor cell. An operational amplifier is used in the successive approximation …

X.25 Interface Packet Level Simulation, Arvind Tewari

Theses

An X.25 interface was simulated at the packet level and data packets successfully transmitted from the Data Circuit-Terminating Equipment (a process) to the Data Terminal Equipment (another process). This was executed interactively. Two independent processesg were generated on the AT&T 3B15 computer and inter-process communication (IPC) used to transfer the data. The X.25 interface is based on the Open System Interconnection (OSI) model of the International Standards Organization.

Durability Of Slurry Cut-Off Walls Around Hazardous Waste Sites, M. Khalid Umer

Theses

A study was undertaken in order to provide insight into the behavior of backfill materials when in contact with hazardous chemicals. It was found that the liquid limit is not a reliable parameter in assessing clay behavior when exposed to these chemicals. However, the expansion index provided a consistent correlation to permeability when all other conditions were kept constant. In addition, the use of fly ash mixed with clay showed an increase in the values of permeability even though its grain size is finer than that of sand. It is believed that this phenomenon was the result of the absence …

Design Of A Lan Based Data Acquisition System For Sensor Applications, Krishna Murthy Uppunda

Theses

This thesis presents the design of a local area network (LAN) based data acquisition system for sensor applications. The circuit designed forms the robotic LAN (RLAN) interface between the sensor IC nodes and the ARCNET network. The RLAN network uses two packet protocols. The sensor data request (SDR) packet is received by the sensor IC nodes and the sensor transmits the sensor data (SD) packet. The RLAN interface provides a two way communication between the sensors and the ARCNET network. Whenever an ARCNET node receives the SDR packet, it stores the packet temporarily in a 1k RAM buffer. The RLAN …

Study Of Steel-Concrete Interface Behavior Of Reinforced Concrete Members, Jun Wan

Theses

The main objective of this thesis work is to study the steel-concrete interface behavior of reinforced concrete members using the nonlinear finite element method.

The reinforced concrete member was modeled as a continuum consisting of plane stress rectangular elements which represent the concrete, pin-joint two node bar elements which represent the reinforcing steel, and the nondimensional linkage elements which represent the bond stress-slip, aggregate interaction and dowel action effects. The load increment procedure is employed to carry out the nonlinear analysis.

An axially loaded tensile specimen, a deep beam specimen and a shallow beam specimen were analyzed. The results from …

Experimental Evaluation Of J-Integral For Concrete Subjected To Impact Loading, Naishan Zhang

Theses

This thesis presents an experimental evaluation of J-integral for concrete subjected to impact loading. Twenty four three-point bend specimens with two different thicknesses and mid-span notch lengths were tested under impact velocities of 167.22 in/sec (424.74 cm/sec) and 261.78 in/sec (664.92 cm/sec). Multi specimen method was used to analyze and estimate J_I and its critical J^-Ic values. Effects of specimen thickness and impact velocity on J^-Ic values were observed and discussed. Evaluation of J^-Ic Values from the experimental results of this study indicated that can be characterized as a material constant even under different impact velocities. …

A Research Analysis : Differences Between Contemporary Corporate Management And Entrepreneurial Management, Kevin A. Gugliotta

Theses

A research analysis was conducted to distinguish the differences between contemporary corporate management and entrepreneurial management. A major difference is in the attitude, perception, and priority of the senior management and the organizational mission. Other distinguishing differences are related to individual and organizational leadership, organizational hierarchy and structure, decision-making authority, and compensation systems for employees.

Use Of The Lms Algorithm In Ecg Analysis, Xiaohua Yang

Theses

The purpose of this thesis is to develop an IBM PC-AT based system to effectively process electrocardiogram (ECG) signals. Adaptive filter theory is used to implement a noise cancellation system (adaptive noise canceller), which adaptively cancels the ECG signals resulting in real ECG noise. The adaptive process is based on the well known least-mean square (LMS) algorithm.

The noise canceling system is software based. Several programs have been written, which include analog to digital converter control, data acquisition and storage, data retrieval, adaptive filtering and digitized data graphics.

The thesis presents numerous computer experiments. The performance of the adaptive noise …

The Influence Of Aggregate Grading With Two Different Binders On Mechanical Strength Of Polymer Concrete, Pei-Yuan Gao

Theses

The scope of this research is to study the influence of grading of the aggregate on the mixing design and the strength of polymer concrete .

Also, the curing conditions, the modification of polymer and the application of coupling agent were investigated.

Based on the experimental results, two numerical methods were developed to be used in combining the aggregates to obtain the desired specific surface area and the grading of the aggregate.

A computer program was developed for one of the methods to give all the possible compositions of the aggregate.

Theoretical explanation is offered and a numerical example is …

Thermodynamic And Leaching Studies Of Various Systems, Satya D. Rami

Theses

The group contribution approach is a reliable and fast method for the prediction of liquid phase activity coefficients in none lectrolyte, nonpolymeric mixtures at low to moderate pressures and temperatures between 300 and 425 K. It has become widely used in practical chemical engineering applications in cases where little or no relevant experimental information is available.

The two group contribution methods examined in the course of this work, are the Knox and & UNIFAC models. Group interaction parameters are evaluated for each of these models and results compared. Although the results for both models are similar when sufficient data are …

A Dynamic Model Of Fill-And-Draw Reactor Utilizing An Inhibitory Substrate, Yun-Fei Ko

Theses

A dynamic model of a fill-and-draw reactor has been developed, which includes a number of operational parameters, the fraction of total cycle time devoted to fill, reaction and draw, and the concentration of the toxic substance in the feed to the reactor.

Operating diagrams have been generated, from which one can choose suitable operating parameters.

The model has been solved numerically for Andrews kinetics ( substrate inhibition ), and tested experimentally, using a 5-liter fill-and-draw reactor with phenol as sole carbon source and a pure culture of Pseudomonas putida. Results compared very well to the model predictions.

Artificial Intelligence And Mechanical Engineering, Efthimios Papayianis

Theses

Many artificial intelligence programs have been developed to assist engineers in their search for solutions. Most of them are designed to assist with a specific type of problem and they usually take the form of an expert system. However one may also use the concepts of artificial intelligence to solve a problem for which an expert system is not yet available.

Three expert systems were developed with Prolog to demonstrate how artificial intelligence can help solve problems in mechanical engineering. The first expert assists in the design of simply supported beams. The second expert assists in the design of thick …

Netexpert, An Expert System For Computer Network Management, Sailen Patel

Theses

Data Communications systems consist of distributed software and hardware components executing concurrently a number of communications functions. The logical framework for these functions is called data communication architecture and is layered hierarchically according to the OSI model. The protocol defines the syntax and semantics of the communications between entities of the same layer. NETEXPERT: An Expert system described here contains a set of formal specifications corresponding to different abstractions level of the protocol. On the highest level there is a specification of the service provided by this protocol. On the consecutive lower levels there are successive refinements of this specification …

Implementation Of A Robotic Workcell, John J. Rogers

Theses

This thesis is intended to provide the reader with some insight into the implementation of robotics technology into an organization. A seven step approach to implementing robotics into an organization was used. The seven steps consist of the following:

1) Initial familiarization with the technology.

2) Plant survey to identify potential applications.

3) Selection of the application.

4) Selection of the robot.

5) Detailed economic analysis.

6) Planning and engineering the installation.

7) Installation.

These steps were applied in an actual organization, the IBM Corp. Real-life processes and operations were utilized in proceeding with the seven step approach. Included in …

Microcomputer Control Of An Ac Induction Motor Using A Pwm Computational Intensive Method, Luther William Schnug

Theses

A three-phase microcomputer based AC Inverter has been developed using a computational intensive PWM algorithm that generates the output bridge switching patterns in real time. This approach utilizes the on-board capabilities of an advanced microcontroller, (a 16-bit 8097 from Intel), to eliminate most of the external hardware, and demands on memory size, required in other designs. This algorithm implements in software the Triangular Modulation Method of PWM generation, and utilizes a trapezoidal approximation to the sinusoidal reference waveform. Brassboard tests have shown that this approximation produces 5th and 7th harmonics that degraded performance, at low speeds. An enhanced algorithm, utilizing …

The Path Method In Power System State Estimation, Fareed A. R. Shirazi

Theses

A new method for Power System State Estimation (PSSE), the 'Path Method', is developed and studied. In this method the state (voltage magnitude and angle) of one node is calculated at a time, using only the local measurements. This procedure is repeated to calculate the state of all nodes in the system, following a predefined path to determine the next node whose state is to be calculated. In the process, more measurements are used whenever available and possible. Results obtained for this method are comparable and close to those of the Line-Flow Only (LFO) method. An advantage of the Path …

Lf Pulse Magnetic Field Generation And Uniformity Studies, Shun-Wen Tan

Theses

This thesis dealt with the design and construction of a pulsed magnetic field (PMF) generation circuit. The spatial variations of the generated PMF are also studied The generated PMF is intended to be used for two purposes (a) in hospitals, for its healing effect of broken bones, and (b) to study the effects of PMF on industrial bacteria and their activity in transforming toxic waste to benign waste

A square coil made of two sections is constructed and the associated circuitry for the PMF generation is designed and built The circuitry is divided into two parts. the control circuit and …

An Application Of Bit Level Systolic Arrays On Digitized Adaptive Array Processes, Shin-Hwa Tsai

Theses

This thesis has concentrated on some aspects of adaptive arrays, i.e., the data type as well as the calculating processes under an optimized version. An adaption of a modified bit-level array is described on the control structure for processes like correlation matrix, Q-R decomposition and solution of triangular linear systems. In short, an implementation of SMI(Sample Matrix Inversion) under a parallel systolic array process is consider5ed. Also an application of utilizing systolic array on a matrix inversion is derived. As a result, it could be predicted that a VLSI chip implementation for small adaptive arrays is feasible in the near …

Degradation Of Dichloromethane, Trichloromethane & Carbon Tetrachloride In A Photoreactor, Sanjay Wadhwa

Theses

A SS 304 photoreactor has been designed to study the degradation of EPA priority pollutants. This newly designed system was used to study the kinetics of degradation of dichloromethane, trichloromethane and carbon tetrachloride under O₂/UV, O₃/O₂/UV and H₂O₂/UV schemes. These compounds have been found to exhibit similar kinetics. The experimental data obtained was. analyzed for pollutant concentration using gas chromatography. The rate constants and mass transfer coefficients were found using a mathematical model to fit the experimental data. A computer program based on the Rosenbrock Hillclimb method in conjunction with …

An Automated System For Optimal Synthesis Of Planar Linkages, Daming Wang

Theses

This thesis addresses the fundamental weakness of the current CAD capabilities and develops a new CAD system with optimization capability. A computer-aided mechanism design system is developed for general problems of optimal kinematic synthesis of planar four-bar mechanisms. The new system is made as user-friendly as possible and it is unique in that it combines Graphics capability, general Analysis capabilities, and Optimization capability into one system. Related background theory in IMP, optimization and optimal synthesis of mechanisms are discussed. The problems and methods in developing the new system are addressed. New routines and modifications made to the original systems are …

Co-Metabolism Of Pentachlorophenol With Glucose Using Two-Stage Anaerobic Activated Carbon Fluidized Beds, Zen Wang

Theses

Abstract - Detoxification of pentachlorophenol by using a two-stage anaerobic biological activated carbon fluidized bed has been investigated. Glucose was introduced as a cosubstrate to determine the relationship between the glucose/PCP ratio and the extent of PCP detoxification in such a system. This system has been proved to be effective in the removal of both PCP and COD. Ratio of glucose to PCP predominates the performance of the system throughout the whole course of this experiment. At a glucose/PCP ratio of 0.33, the system has a highest reduction of both PCP and COD. Addition of glucose to the highly PCP …

Decontamination Of Contaminated Clay Soils By Thermal Treatment, Chandrakanthi Weerasinghe

Theses

An experimental investigation on the desorption of contaminated clay soils by thermal treatment was performed. This study was carried out on two clay soils (kaolinite and bentonite) sorbed with three liquid organic compounds (phenol, chlorophenol, and chlorobenzene). The study consists of two different phases, the adsorption and desorption. The results on batch equilibrium adsorption were correlated with different isotherm models of which the Freundlich isotherm model was found to be best fit in predicting adsorption capacities of kaolinite, and that for bentonite was found to be the linear isotherm model.

A thermal desorption study followed the equilibrium adsorption study. A …

Effects Of Compliance And Machining Prameters On Robotic Grinding/Deburring, Kung-Le Chang

Theses

A theoretical model for robotic grinding/deburring has been developed and compared with experimental results. Various grinding parameters such as depth of cut, feed rate, surface profile and roughness, grinding forces, and robot stiffness, have been experimentally investigated in this study. It was observed that the depth of cut is a function of specific grinding energy, force, and robot compliance. The observed roughness and waviness are directly proportional to depth of cut and feed rate and, in addition, to the robot compliance and the encoder quantization error. Other effects of the robot system for grinding performance are also addressed.

Charge Transfer Inefficiency Of Buried-Channel Charged Coupled Device Registers For Low Temperature Operation Of Ptsi Infrared Image Sensors, Benjamin Benjamin Esposito

Theses

Buried channel charge coupled devices used as readout registers in PtSi Schottky-barrier detector infrared image sensors were investigated to characterize factors that influence charge transfer efficiency at low temperatures ranging from 38 to 80K. These factors included frequency of operation, background signal, gate voltage, signal level, gate length, and temperature. It was found that increased gate voltage and decreased gate length are most effective in reducing charge transfer efficiency. This was attributed to increased fringing fields between the potential wells involved in charge transfer. As temperature was decreased from 50K to 38K progressively larger trapping losses were observed due to …

Hydrodynamic Lubrication Performance Of Mineral Oils With Polymer Additives, Moshe David Felzenstein

Theses

This study was undertaken with the view to determining experimentally the influence of polymer additives on journal bearing performance under static load. Viscoelastic lubricants such as oils with polymer additives are in common use and exhibit a reduced dependence of the viscosity on temperature but the effect on the performance of a static journal bearing is not clear. Additives of the polymer polyisobutylene and STP were blended with Newtonian base oil which was used to establish the baseline performance of the test bearing. A comparison was made between the performance of these blends and the base oil. The performance of …

Respiratory Impedances Computed From The Forced Oscillation Technique Using An Esophageal Balloon, Richard Thomas Fisler

Theses

The purpose of this investigation is to develop methodology for the standard measurement and physiological interpretation of lung resistance and compliance using non-invasive forced oscillations techniques and validating these results with standardized esophageal balloon techniques. Application of the forced oscillation technique with an esophageal balloon in place permits partitioning of the respiratory system into the pulmonary system which is of primary interest and the less clinically important chestwall system. Diseased lung states are induced in normal subjects by inhalation of a bronchoconstrictor. The total respiratory (pulmonary plus chest wall) and pulmonary impedances are interpreted using both a linear three element …

The Evaluation Of The Impact Of Reducing The Domestic Wastewater Phosphorus On The Algal-Related Water Quality Of The Hudson/Raritan Estuary And Northern New Jersey's Coastal Waters, Ron Gautreau

Theses

An investigation was undertaken to examine the planktonic algal-related water quality of the Hudson/Raritan Estuary and northern New Jersey's coastal waters with respect to quantifying the relationship between the amount of phosphorus loading to the planktonic algal-related water quality responses. Recreational and commercial uses of northern New Jersey's coastal waters have at times been impaired by excessive growth of planktonic algae. Using population equivalents and export coefficients the amount of domestic wastewater and land runoff derived phosphoruscontributed to the Estuary was estimated. The P load contributed to the Estuary via the discharge of New York and New Jersey domestic wastewater …

Three Dimensional Study Of Macromolecular Leakage Patterns Using Video Image Analysis, Nikhil V. Khimani

Theses

It has long been known that blood - tissue transport of macromolecules in the microcirculation is driven by diffusion. Although two dimensional models fit the experimental data well, the diffusion process is three dimensional.The objective of this research was to establish a three dimensional unsteady state mathematical model for intravascular transport of macromolecules, and suppoi t the theoretical establishment by experimental results.

Three dimensional diffusion of macromolecules through the interstitial space in the hamster cheek pouch was studied, with intravital fluorescence microscopy. After application of bradykinin, the movement of Fluorescein isothiocynate (F.I.T.C.) - labeled Dextrans of average molecular weight 150,000 …