Engineering Commons^™

Poly (Lactic Acid)/Nanoclay Nanocomposites For Packaging Applications, Maissa Akram Adi

Theses

With increasing stringent environmental regulations and attempts to reduce dependence on fossil fuels for polymer production, bio-based polymers are receiving appreciable global attention. In this context, bio-based poly (lactic acid) (PLA) is one of the most frequently used polymers in packaging applications. However, despite of its high versatility, this polymer is limited in packaging applications due to its low mechanical properties. The two-dimensional nanofillers such as nanoclay and graphene are well known for improving the thermo-mechanical properties of polymers at low concentrations. However, increasing higher filler concentration to improve barrier properties of polymers reduces their mechanical properties which is a …

Deep Learning For Quantitative Motion Tracking Based On Optical Coherence Tomography, Peter Abdelmalak

Theses

Optical coherence tomography (OCT) is a cross-sectional imaging modality based on low coherence light interferometry. OCT has been widely used in diagnostic ophthalmology and has found applications in other biomedical fields such as cancer detection and surgical guidance.

In the Laboratory of Biophotonics Imaging and Sensing at New Jersey Institute of Technology, we developed a unique needle OCT imager based on a single fiber probe for breast cancer imaging. The needle OCT imager with sub-millimeter diameter can be inserted into tissue for minimally invasive in situ breast imaging. OCT imaging provides spatial resolution similar to histology and has the potential …

Recovery Of Valuable Metals From Spent Lithium-Ion Batteries Using Organic Acids: Assessment Of Technoeconomic Feasibility, Leqi Lin

Theses

Lithium ion batteries (LIBs) are used in diverse electronic products with anticipated over 500 thousand tonnes of the waste LIBs globally in 2020. To protect the environment and also recover valuable materials such as lithium (Li) and cobalt (Co), our research employed a hydrometallurgy method and demonstrated that exposure of spent LIBs to Organic Aqua Regia (OAR) could leach Li and Co without the pre-separation of cathode from Al foil using organic solvents such as Dimethylformamide (DMF) and N-Methyl-2-pyrrolidone (NMP). The leaching efficiency of 99% and 94% for Li and Co were obtained with a leaching rate of 0.021, 0.167 …

Enhanced Removal Of Perfluorooctanoic Acid (Pfoa) Via Microwave-Fenton-Reactive Membrane Filtration, Fangzhou Liu

Theses

Perfluorooctanoic Acid (PFOA), one of the common per- and poly fluorinated alkylated substances (PFASs), is increasingly detected in the environment due to the diverse industrial applications and high resistance to degradation processes. This study evaluated degradation of PFOA in microwave-assistant catalytic membrane filtration, a process that integrates microwave catalytic reactions into a ceramic membrane filtration. First, water permeation of the pristine and catalyst-coated membranes were examined under the influence of microwave irradiation to analyse the impacts of the coating layer and water temperature increase on permeate flux, which were well interpreted by three models. Then, the PFOA removal was first …

Model-Based Deep Siamese Autoencoder For Clustering Single Cell Rna-Seq Data, Zixia Meng

Theses

In the biological field, the smallest unit of organisms in most biological systems is the single cell, and the classification of cells is an everlasting problem. A central task for analysis of single-cell RNA-seq data is to identify and characterize novel cell types. Currently, there are several classical methods, such as K-means algorithm, spectral clustering, and Gaussian Mixture Models (GMMs), which are widely used to cluster the cells. Furthermore, typical dimensional reduction methods such as PCA, t-SNE, and ZIDA have been introduced to overcome “the curse of dimensionality”. A more recent method scDeepCluster has demonstrated improved and promising performances in …

Spectral 3d Reconstruction Based On Macroscopic Oct Imaging, Xingyu Zhou

Theses

Various optical technologies have been utilized to improve art conservation by art conservators, such as laser triangulation, stereophotogrammetry, structured light, laser scanner and time of flight sensors. These methods have been deployed to capture the 3D or surface topography information of sculptures and architectures. Optical coherence tomography (OCT) has introduced new imaging methods to study the surface features and subsurface structures of delicate cultural heritage objects. However, despite its higher spatial resolution, the field of view (FOV) of OCT severely limits the size of the scanning area and does not allow macroscopic examination. To solve this issue, we develop and …

An Information Theoretic Approach To Assess Perceived Audio Quality Using Eeg With Reduced Number Of Electrodes, Sansit Das

Theses

Electroencephalograph(EEG) is a process mainly used in medical and research fields to study the electrical activities in a brain. In this technique, 128 or 256 electrodes are attached to the scalp and the electrical activities of the human brain is recorded with the help of a software. In the global scenario, the EEG responses are studied and analysed to acknowledge any disorders in the brain, such as epilepsy or head injury.

Recent studies performed by researchers, have focused on analysing these electrical activities to access perceived audio quality from users by using information theoretic approaches, such as mutual information. Experiments …

Development Of A Composite Sustainability Index For Roadway Intersecttion Design Alternatives In The Uae, Maryam Juma Al-Kaabi

Theses

Many studies had been carried out to evaluate the sustainability of transportation systems, but little attention was given in these studies to the design of roadway intersections. The objective of this study was to define a framework to assess intersection sustainability from a road-user perspective and to develop a visual tool that helps decision-makers to support a more sustainable design of roadway intersections. Suitable sustainability indicators that would serve as elements in the built framework at the strategic and early planning level were extracted from the literature. The extracted indicators were utilized with relative weights to develop basic dimensional indices …

Smart Inverters For Distributed Pv Network Management, Colin Charles Levis

Theses

Securing a sustainable decarbonised economy involves moving towards a decentralised power system with increasing penetration levels of distributed photovoltaics (PVs) within the low voltage distribution network (LVDN). Increasing penetration levels of PV systems pose challenges for maintaining grid voltage and frequency stability. Thus requires studies and simulations to estimate the needs and technical requirements to overcome the challenges and maximise the opportunities. These simulations require time-domain system models with a high dynamic resolution such as electromagnetic transient (EMT) simulations with small-time steps that capture the required performance with large numbers of network elements. However, the small-time step implies a high …

Assessment Of Different Seismic Retrofit Systems Of Rc Buildings For Earthquake Risk Mitigation, Aya Ragab Mohamed Abou Ei-Hamd

Theses

Many existing Reinforced Concrete (RC) structures were designed and constructed at a time when design codes were insufficient according to current standards. This class of structures is at risk of damage when subjected to strong earthquake loading. Therefore, several seismic retrofit techniques have been investigated experimentally to increase the earthquake resistance and damage-control potential of pre-seismic code structures using different methods such as quasi-static and pseudo-dynamic testing. However, a limited number of studies have focused on investigating the overall seismic performance of retrofitted RC structures using shake table testing. The first task of this study assesses analytically and experimentally the …

Control Of Energy Storage Utilisation For A Building Integrated Microgrid Using Multi-Objective Metaheuristic Optimisation Methods, Quang An Phan

Theses

The aim of this thesis was to develop and analyse optimisation strategies for commercial buildings with integrated microgrids, in order to find optimal trade-offs between maximising profitability and facilitating renewable energy from the national power grid. The continued proliferation of microgrids, as well as the increase in electricity produced by renewable energy sources on the Irish national grid has necessitated the requirement for these strategies. Models to simulate the performance of a photovoltaic system, wind turbine and battery bank were developed and validated. The most suitable optimisation algorithm to generate an optimal charge/discharge rate schedule for a battery bank was …

Viability Analysis Of Tralee’S District Heating System, Ed O’Connor

Theses

At present a large proportion of domestic and commercial heating systems in Ireland are fossil fuel based. Decarbonisation of Irelands heating system would mean a shift away from traditional fossil fuels, and a step towards more renewable and sustainable thermal energy systems. This thesis outlines a viability analysis of one of the options available to assist in the achievement of Ireland’s thermal energy goals and carbon emissions targets. The option considered in this proposal is the development of a wood chip fuelled District Heating System (DHS) to cater for the thermal needs of the town of Tralee. Several alternatives DHS …

Micro Pipes – A Portable Integrated Platform For Electrochemical Sensing Using Essence Architecture, Hansin Kim

Theses

The field of microfluidics and lab-on-chip (LOC) technology has the potential to have a truly transformative effect in biological engineering. This includes areas such as single-cell analysis, environmental monitoring, regenerative medicine, and point-of-care diagnostics. Yet despite being the subject of intense research over the past two decades, LOC devices have not been widely adopted. It is increasingly evident that there is a need for an effective and adaptable integration strategy to realize the potential of this technology.

Presented in this thesis is a design for a chip-to-world interface that aims to improve integration while maintaining cost-efficiency and ease of fabrication. …

Magnetic Field Effects On Lithium Ion Batteries, Kevin Mahon

Theses

The Nobel Prize in Chemistry 2019 was just recently awarded to John B. Goodenough, M. Stanley Whittingham, and Akira Yoshino for the development of lithium-ion batteries. Lithium-ion batteries have seen use in many different industries and applications such as in portable devices, power grids, and electric vehicles. As lithium-ion batteries become more commonplace they will need to be modeled more extensively. The magnetic field effect on lithium-ion batteries has not been studied significantly since they were first discovered.

Modeling these batteries is still difficult because of the many complexities of the operation of a battery. Lithium-ion batteries are commonly modeled …

Impact Of Stirrer Speed And Media Type-Loading On The Breakage Kinetics During Wet Stirred Media Milling Of Griseofulvin, Nathaniel Parker

Theses

The aim of this study is to investigate the impact of stirrer speed (2000-4000 rpm) and bead loading (~20-60%) on the breakage kinetics-energy consumption during milling of griseofulvin, a poorly soluble drug, and compare the performance of crosslinked polystyrene (CPS) beads with that of yttrium-stabilized zirconia (YSZ) beads. Laser diffraction, SEM, viscometry, and XRPD were used for characterization. A microhydrodynamic model was used to interpret the breakage kinetics. An increase in stirrer speed led to faster breakage due to more frequent and forceful CPS bead-bead collisions. Despite causing slight decrease in maximum contact pressure, an increase in CPS bead loading …

Lithium As A Possible Therapeutic Drug In Posttraumatic Brain Injury, Tulika Das

Theses

Lithium, a popular drug for treating mental health disorder has shown promising effect in recent research on traumatic brain injury (TBI). The mechanism of lithium for treating bipolar mood disorder is still not properly understood, but recent studies showed that lithium is neuroprotective in TBI. In my thesis, the neuroprotective effects of lithium were examined in primary neuronal culture and mild blunt injury using rodent model of Lateral Fluid Percussion Injury (LFPI). At first determination of the neuroprotective/toxicity effects of lithium in neuronal culture was done and observed that 0.5 - 1.0 mM concentrations were found to be neuroprotective as …

Effect Of 3d Printed Tablet Shape On Drug Release Profile, Christina Gedeon

Theses

There is a growing interest in utilizing additive manufacturing (AM) as a manufacturing tool to develop oral tablets for personalized medicine. This ultimate goal in mind, this study explores the feasibility of extrusion-based fused deposition modeling (FDM) to 3D print oral tablets with tunable design to control drug release profile. Tablets are printed using poly(vinyl alcohol) (PVA) loaded with model drugs: acetaminophen and caffeine. Hot melt extrusion (HME) is used to fabricate PVA filaments loaded with acetaminophen and caffeine. These filaments are used to fabricate a range of tablets with varying designs to prepare immediate and delayed release tablets. Thermal …

Study And Modelling Of Lithium Ion Cell With Accurate Soc Measurement Algorithm Using Kalman Filter For Electric Vehicles, Kasthuriramanan Mahendravadi Sivaguru

Theses

Lithium Ion cells are preferred over lead acid cells for electric vehicles due to their energy density, higher discharge current and size. The cost of lithium ion cells is scaling down compared to ten years earlier, but as their performance characteristics increase, the need for safety and accurate modelling also increases.

The absence of a generic cell model is associated to the different makes of cells and different chemistries of Lithium ion cells behave differently under the testing conditions required for every unique application. The focus of this thesis will be on how to provide intelligence to the battery management …

Multi-Objective Optimal Capacity And Placement Of Distributed Generators In The Power System Networks Using Atom Search Optimization Method, Ashwaq Faisal Alkhatib

Theses

Nowadays, renewable energy sources become a significant source of energy in the new millennium. The continuous penetration of dispersed resources of the reactive power into power systems is predicted to introduce new challenges. Power loss mitigation and voltage profile development are the major investigation challenges

that recently attracted the attention of researchers in the field of power systems. Distributed generation (DG) is widely preferred because it is a highly effective solution that strengthens the performance of power system networks. This multiobjective function study aims to minimise power losses in the feeders, sustain voltage levels and reduce the application cost of …

Graphene/Polypropylene Nanocomposites, Carmen Karam Abuoudah

Theses

Graphene has been regarded as a multifunctional nanofiller for manufacturing polymer nanocomposites. A small amount of graphene nanosheets is expected to significantly improve the properties of base polymers. The property enhancement, however, is a function of the degree of exfoliation and dispersion of graphene as well as its compatibility with the polymer. The non-polar nature of polyolefins such as polyethylene (PE) and polypropylene (PP) restricts the homogeneous dispersion of graphene, leading to significant agglomeration of the nanosheets and thus, limiting the expected property improvements in polyolefins. Currently, more efforts are focused on finding strategies to improve graphene dispersion in polyolefins. …

Introducing Digital Content To Kclc, Chad Briesacher

Theses

No abstract provided.

Home Energy Management System For Demand Response Purposes, Isra Adam Hussein Haroun

Theses

The growing demand for electricity has led to increasing efforts to generate and satisfy the rising demand. This led to suppliers attempting to reduce consumption with the help of the users. Requests to shift unnecessary loads off the peak hours, using other sources of generators to supply the grid while offering incentives to the users have made a significant effect. Furthermore, automated solutions were implemented with the help of Home Energy Management Systems (HEMS) where the user can remotely manage household loads to reduce consumption or cost. Demand Response (DR) is the process of reducing power consumption in a response …

The Assessment Of Walkability As A Social Aspect Of Sustainability: The Case Of Dubai Neighborhoods, Uae, Rania Elsaed Elesawi

Theses

In an attempt to reduce car dependency, the process of planning, mainly on a neighborhood level, has recently been directed to focus on the accommodation of walkability as a significant factor of planning development. This approach contributes not only to improving urban patterns but also majorly in addressing issues of sustainability. The social aspect of sustainability has not received much attention and is considered the least described pillar. The positive association between aspects of human behavior and built environment, particularly walkability, suggests that measuring social aspects of sustainability may be conceivable especially in the context of community development. Sustainable neighborhoods …

An Electrical Matlab Model Of Plasma Electrolytic Oxidation, Huize Xue

Theses

Plasma Electrolytic Oxidation (PEO), a part of Plasma electrolytic Deposition (PED), has been developing for surface modification of metallic materials in the past 20 years. During PEO process, sample always connect with anode of DC power source, under high temperature, accelerating process of oxidation reaction to from an average and dense oxidation film. A general passage, Plasma electrolysis for surface engineering, written by A.L. Yerokhin, X. Nie gives us a trend of what happened during PEO process but did not determine specific material and value. Linxin Zhu’s Development of PEO invent a new boiling system and investigated relationship between surface …

Blind Source Separation Using Dictionary Learning Over Time-Varying Channels, Anushreya Ghosh

Theses

Distributed sensors observe radio frequency (RF) sources over flat-fading channels. The activity pattern is sparse and intermittent in the sense that while the number of latent sources may be larger than the number of sensors, only a few of them may be active at any particular time instant. It is further assumed that the source activity is modeled by a Hidden Markov Model. In previous work, the Blind Source Separation (BSS) problem solved for stationary channels using Dictionary Learning (DL). This thesis studies the effect of time-varying channels on the performance of DL algorithms. The performance metric is the probability …

Design And Implementation Of An Automated Oil Distribution System For A Homogenizer Machine In Gea Mechanical Equipment – Niro Soavi, Luca Gandolfi

Theses

This thesis shows the steps that have been followed and done in order to improve a critical operation of a technological process of the GEA Mechanical Equipment. The critical operation was the filling with different types of oils the homogenizing machine because it was characterized by a lot of inefficiencies and, in particular, by huge risks for job security. These critical issues gave the opportunity and the chance to realize a project in order to give a process optimization and security improvement.

After having faced all the aspects and steps needed for this project, it has been realized a system …

Vergence Eye Movement Parameters For Pre/Post-Obvat And Sham Therapy On Binocularly Normal Controls, Joel V. Rajah

Theses

Vergence is the disjunctive movement of the eyes to maintain single binocular vision. Vergence eye movements are necessary to maintain the object of interest on the fovea of each eye as an individual looks from one object to another. Recent studies show that office based vergence/accommodative therapy (OBVAT) is an effective treatment for the binocular dysfunction known as convergence insufficiency. This study was performed to investigate the changes in oculomotor parameters parameter data for pre- and post-therapy subjects who are binocularly normal controls. A haploscope was used to collect eye movement data pre- and post-therapy. The analysis of the eye …

Glass Transition Temperature Of Particles For Drug Delivery, Yiqing Yang

Theses

Drug delivery plays an important role in targeted therapies and nanoparticles which can be used as drug carriers and it’s a frequently researched topic. Poly(lactic-co-glycolic acid) (PLGA), a highly biocompatible polymer, has been used as a drug delivery vehicle in many studies. One of the challenges facing drug delivery particles is the problem of burst release which is when a large amount of the drug is suddenly released from the particle once it is placed in the body. This is generally undesirable as usually a slow and controlled release is preferred. The glass transition temperature has an effect on drug …

Multiframe Coded Computation For Distributed Uplink Channel Decoding, Brinell F. Monteiro

Theses

The latest 5G technology in wireless communication has led to an increasing demand for higher data rates and low latencies. The overall latency of the system in a cloud radio access network is greatly affected by the decoding latency in the uplink channel. Various proposed solutions suggest using network function virtualization (NFV). NFV is the process of decoupling the network functions from hardware appliances. This provides the exibility to implement distributed computing and network coding to effectively reduce the decoding latency and improve the reliability of the system. To ensure the system is cost effective, commercial off the shelf (COTS) …

Tomato Puree Convective Heat Transfer Simulation Using Boussinesq Approximation, Matteo Fabbri

Theses

With the advance of new technologies, the food industries are requiring systems that allow to produce the desired products with faster rates at cheaper costs. In this case, the study was initiated with the purpose to better understand what happens inside a package containing tomato puree when this is heated above 343 K in a tunnel pasteurizer. If the fluid must reach the thermal and microbiological condition of “pasteurization”, the system must guarantee that the temperature (around 343° Kelvin) is kept for a certain time allowing to pasteurize even the cooler package’s fluid-particle. The faster the system can heat the …